ML19256F766
| ML19256F766 | |
| Person / Time | |
|---|---|
| Issue date: | 07/31/1977 |
| From: | Office of Nuclear Reactor Regulation |
| To: | |
| References | |
| NUREG-0313, NUREG-313, NUDOCS 7912200782 | |
| Download: ML19256F766 (15) | |
Text
N U REG-0313 TECHNICAL REPORT ON MATERIAL SELECTION AND PROCESSING GUIDELINES FOR BWR COOLANT PRESSURE BOUNDARY PIPING
, n,,,
k 1780 292 Office of Nuclear Reactor Regulation U. S. Nuclear Regulatory Commission 7912200~/h
A'"IlabI' from NationalTjhnicajyMormatij,g,rvice f Se 8Pring eld, yg "g'nra
- & $3.5
'rofiche $3.00
- rice: printed The price of this document for requesters outside of the North American Continent can be obtained from the National Technical Information Service.
NUR EG-0313 TECHNICAL REPORT ON MATERIAL SELECTION AND PROCESSING GUIDELINES FOR BWR COOLANT PRESSURE BOUNDARY PIPING Manuscript Completed: July 1977 Date Published: July 1977 i780 M 3 Division of Operating Reactors Division of Systems Safety Office of Nuclear Reactor Regulation U. S. Nuclear Regulatory Commission Washington, D. C. 20555
-i-TABLE OF CONTENTS 1.
INTRODUCTION.........................
1 II.
SUMMARY
OF ACCEPTABLE METHCDS TO MINIMIZE CRACK SUSCEPTIBILITY 3
III.
INSERVICE INSPECTION AND LEAK DETECTION REQUIREMENTS FOR BWRs WITH VARYING CONFORMANCE TO MATERIAL SELECTION AND PROCESSING GUIDELINES....................
4 IV.
IMPLEMENTATION OF MATERIAL SELECTION AND PROCESSING GUIDELINES 9
V.
GENERAL RECOMMENDATIONS
...................10 1780 294
I.
16TRODUCTION Small, hairline cracks in austenitic stainless steel piping in boiling water reactor (BWR) facilities were observed as early as 1965.
In each case, it was believed that the situation had been corrected or substan-tially reduced by better control of welding, contaminants and/or design modifications.
In September,1974, when the first of a series of cracks in the piping of the more modern BWRs was found at Dresden Unit No.
2.,
the then Atomic Energy Commission (AEC) initiated an intensive investiga-tion to evaluate the cause, extent, and safety implications of the observed cracking.
In January 1975, a special Pipe Cracking Study Group was formed to coordinate and accelerate the staff's continuing investiga-tions of the occurrences of pipe cracking. This group included represen-tatives of the Nuclear Regulatory Commission (NRC) and their consultants.
In October, 1975, the Study Group issued a report, NUREG-75/067 " Tech-nical Report, Investigation and Evaluation of Cracking in Austenitic Stainless Steel Piping of Boiling Water Reactor Plants." During the same general time span, the General Electric Company (GE) conducted an indepen-dent evaluation of the cracking occurrences and submitted their findings and recommendations to the NRC. This paper sets forth the NRC technical position based on the information available at this time.
Plant operating history indicates that Type 304 and 316 austenitic stainless steel piping in the reactor coolant pressure boundary of boiling water reactors are susceptible to stress corrosion cracking.
1780 295 Studies have shown that such cracking is caused by a combination of
.the presence of significant amounts of oxygen in the coolant, high stresses, and some sensitization of metal adjacent to welds. Such cracks have occurred in the heat affected zones adjacent to welds but are not expected to occur outside these areas, provided that the pipe material is properly annealed.
Pipe runs containing stagnant or low velocity fluids have been observed to be more susceptible to stress corrosion cracking than pipes containing a continuously flowing fluid during plant operation.
Historically, t.1ese cracks have been identified either by volumetric examination, by leak detection systems, or by visual inspection.
Because of the inherent high material toughness of austenitic stainless steel piping, stress corrosion cracking is unlikely to cause a rapidly propagating failure resulting in a loss-of-coolant accident.
Although the probability is extremely low that these stress corrosion cracks will propagate far enough to create a significant safety hazard to the public, the presence of such cracks is undesirable.
Steps should therefore be taken to minimize stress corrosion cracking in BWR piping systems to eliminate this condition and to improve overall plant reliability.
It is the purpose of this position to set forth acceptable methods to reduce the stress corrosion cracking susceptibility of BWR piping and thereby also provide an increased level of reactor coolant pressure D
boundary integrity.
Recognizing that the most straightforward and y&
N desirable approach or methods may not be practicable, or even possible, for all plants, the bases fcr varying degrees of conformance to our guidelines are provided. Augmented inservice inspection and leak detec-tion requirements are established for plants that have not fully implemented the provisions contained in Part II of this document.
SUMMARY
OF ACCEPTABLE METHODS TO MINIMIZE CRACK SUSCEPTIBILITY The material selection and processing guidelines listed below identify alternative acceptable methods to minimize susceptibility to stress corrosion in BWR pressure boundary piping.
It is expected that adoption of these practices will result in a high degree of protection against stress corrosion cracking.
1.
Corrosion Resistant Materials All pipe and fitting material including weld metal should be of a type and grade that has been shown to be highly resistant to oxygen-assisted stress corrosion in the as-installed condition.
Unstabilized wrought austenitic stainless steel with >0.035%
carbon does not meet this requirement unless all such piping including welds is in the solution annealed condition. The acceptability of alternative materials, processes, or other methods to provide an adequate degree of corrosion resistance will be made on a case-by-case basis.
2.
Corrosion Resistant " Safe Ends" All unstabilized wrought austenitic stainless steel piping with carbon contents >0.035% should be in the solution annealed condition.
1780 297 If welds joining these materials are not solution annealed, they should be made between case (or weld overlaid) austenitic stainless steel surfaces (5% minimum ferrite) or other materials having high resistance to oxygen-assisted stress corrosion. The joint design must be such that any unstabilized wrought austenitic stainless steel containing 1 035% carbon, which may become sensitized as a result 0
of the welding process, is not exposed to the reactor coolant.
3.
Other proposed methods to provide protection against stress corrosion cracking will be reviewed on a case by case basis.
Regulatory Guide 1.44 " Control of the Use of Sensitized Stainless Steel",
dated May, 1973 will be revised to provide additional guidance on acceptable practices.
III.
INSERVICE INSPECTION AND LEAK DETECTION REQUIREMENTS FOR BWRs WITH VARYING CONFORMANCE TO MATERIAL SELECTION AND PROCESSING GUIDELINES 1.
For plants where all ASME Code Class I reactor coolant pressure boundary piping subject to inservice inspections under Section XI meets the guidelines stated in Part II, no augmented inservice inspection or leak detection requirements are necessary.
2.
Piping in all other plants is subject to additional inservice inspection and leak detection requirements, as described below.
The degree of inspection of such piping depends on whether the specific piping runs are conforming or non-confonring, and on whether the specific piping runs are classified as " Service 1780 298 Sensitive".
" Service Sensitive" lines are defined as those that have experienced cracking in service, or that are considered to be particularly susceptible to cracking because of high stress, or because they contain relatively stagnant, intermittent, or low flow coolant.
Examples of piping runs considered to be service sensitive include, (but are not limited to): core spray lines, recirculating by-pass lines (or " stub tubes" on plants that have removed the by-pass lines)
CRD hydraulic return lines, isolation condenser lines, and shut down heat exchanger lines.
A.
For non-conforming lines that are not service sensitive:
(1)
Inservice inspection of the non-conforming lines should be conducted in accordance with the schedule specified in ASME Code,Section XI - Subsection IWB, as required by the applicable examination Categories B-F and B-J, with the exception that the required examination should be completed in no more than 80 months (two thirds of the time perscribed in the schedule in the ASME Boiler and Pressure Vessel Code Section XI).
If examinations conducted during the first 80 month period reveal no incidence of stress corrosion cracking, the examination schedule thereafter can revert to the schedule perscribed in Section XI of the ASME Boiler and Pressure Vessel Code.
1780 299 The piping areas subject to examination, the method of examina-tion, the allowable indication standards and examination pro-cedures should comply with the requirements of the Edition and Addenda of the ASME Code,Section XI identified as applicable by 10 CFR Part 50, Section 50.55a, Paragraph (g), " Codes and Standards."
(2) The reactor coolant leakage detection system should be operated under the following Technical Specification requirements in order to enhance the discovery of unidentified leakage that may include through-wall cracks developed in austenitic stainless steel piping:
a.
The source of reactor coolant leakage should be identifiable to the extent practical, using leakage detection and collec-tion systems that meet the position described in Section C, Regulatory Position of Regulatory Guide 1.45, " Reactor Coolant Pressure Boundary Leakage Detection Systems," or an acceptable equivalent system.
b.
Plant shutdown should be initiated for inspection and corrective action when the leakage system indicates, within a period of four hours or less, an increase in the rate of unidentified leakage in excess of two gallons per minute, or when the total unidentified leakage attains a rate of five gallons per minute, whichever occurs first.
1780 3u0 c.
Unidentified leakage should include all leakage other than:
1.
Leakage into closed systems, su~ch as pump seal or valve packing leakage that is captuced, metered, and conducted to a sump or collecting tank, 2.
Leakage into the containment atmosphere from sources that are specifically located and known either not to interfere with the operation of the unidentified leakage detection system, nor not to be from a through-wall crack in the piping within the reactor coolant pressure boundary.
B.
For non-conforming lines that are service sensitive:
(1) The leakage detection requirements described in III.A above, should be implemented.
(2) The welds and adjoining areas of bypass piping of the discharge valves in the main recirculation loops, and of the austenitic stainless steel reactor core spray piping up to and including the second isolation valve should be examined at each reactor refueling outage or at other scheduled or unscheduled plant shutdowns. Successive examinations need not be closer than six months, if shutdowns occur more frequently than six months. This requirement applies to all bypass lines whether the 4-inch valve is kept open or closed during operation, jJQ]
']l In the event these examinations find the piping free of unacceptable indications for three successive inspections, the examination may be extended to each 36 month period (plus or minus by as much as 12 months) coinciding with a refueling outage.
In these cases, the successive examination may be limited to one bypass pipe run, and one reactor core spray piping run.
(3) The welds and adjoining areas of other service sensitive piping should be examined on a sampling basis.
For example, if a system consists of several branch runs with essentially symmetric piping configurations that perform similar system functions, an acceptable inspection program should include at least one, but not less than 25%, of the similar branch runs. The frequency of such examinations should be as described in 2 above.
If unacceptable flaw indications are detected in any branch run, the remaining branch runs among the group should be examined.
In the event the examinations reveal no unacceptable indica-tions within three successive inspections, the examination schedule may revert to the ASME Boiler and Pressure Vessel Code,Section XI, " Inservice Inspection of Nuclear Power Plant Components" with the exception that the required examination should be completed during each 80 month period (two-thirds the time perscribed in the schedule in the ASME Code Section XI).
1780 302 (4) The method of examination, the allowable indication standards and examination procedures should comply with the requirements of the Edition and Addenda of the ASME Code,Section XI identified as applicable by 10 CFR Part 50, Section 50.55a, Paragraph (g), " Codes and Standards."
IV.
IMPLEMENTATION OF MATERIAL SELECTION AND PROCESSING GUIDELINES 1.
For plants that apply for a construction pennit after the issue date of this document, all ASME Code Class I reactor coolant pressure boundary lines should conform to the guidelines stated in Part II.*
2.
For plants under review, but for which a construction permit has not yet been issued, all service sensitive lines should conform to the guidelines stated in Part II. Other ASME Code Class I reactor coolant pressure boundary lines should conform to Part II to the extent practicable.
3.
For plants that have been issued a construction permit, ASME Code Class I reactor coolant pressure boundary lines should conform to the guidelines stated in Part II to the extent practicable.
- Af ter revision, Regulatory Guide 1.44 may be used as guidance for acceptable materials, process, or other methods.
1780 503 4.
For plants that have been issued an operating license, service sensitive lines should be modified to conform to the guidelines stated in Part II, to the extent practicable.
Lines in which cracking is experienced should be replaced with piping that conforms to the guidelines stated in Part II.
V.
GENERAL RECOMMENDATIONS The measures outlines in Part II of this document provide for positive actions that are consistent with the current technology. The implemen-tation of these actions should markedly reduce the susceptibility to stress corrosion cracking in BWRs.
It is recognized that additional techniques are available to limit the corrosion potential of BWR coolant pressure boundary materials and improve the overall system integrity.
These include plant design and operational considerations to reduce system exposure to potentially aggressive environment, improve material fabrication and welding techniques and provisions for volumetric inspec-tion capability in the design of weld joints. Specifically, considera-tion should be given to:
1.
K aimizing the total extent of the coolant pressure boundary with special emphasis on stagnant or low flow lines.
2.
Reducing the oxygen content of the primary coolant.
1780 304
Om,
'ES f
)
'l t,4 4
' IO
" Q,t,0.
'NorO c-05y4Ce NO, ES a4,
'"~4< : ;g, %, ;~,..
s ol ' o,, $, ',* t e., N' ;
s
'*r
c.,,,,
4
'80 305
/ '