ML14282A476

Final Written Examination with Answer Key (401-5 Format) (Folder 2)

ML14282A476
Person / Time
Site:	Susquehanna
Issue date:	08/18/2014
From:	Susquehanna
To:	D'Antonio J Operations Branch I
References
TAC U01896
Download: ML14282A476 (219)

Text

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam I RO I Tier I2 I Group 11 I Cognitive Level I High I Level of Difficulty I 2 KIA 215004 K1.02 Source Range Monitor System I Importance 1 3.4 Statement Knowledge of the physical connections and/or cause-effect relationships between SOURCE RANGE MONITOR (SRM) SYSTEM and Reactor manual control.

QUESTION 1 Unit 1 startup is in progress.

The reactor is critical with a 300-second period.

While operators are withdrawing SRMs per G0-200-002, annunciator ROD OUT BLOCK (AR-1 04-H03) is received .

Operators stop withdrawing SRMs and note the following SRM readings:

Counts SRM (cps) Position A 90 Partially withdrawn B 200 Partially withdrawn c 8E4 Fully inserted D 2E5 Fully inserted IRMs are reading 10 on Range 2.

Which one of the following identifies the actions that will clear the ROD OUT BLOCK alarm and allow control rod withdrawal to continue?

A. Bypass SRM D, ONLY B. Insert SRM A to obtain approximately 1000 cps, ONLY C. Place all IRMs on Range 3 Bypass SRM D D. Insert SRM A to obtain approximately 1000 cps Bypass SRM D Proposed Answer D Applicant References None Explanation SRMs A and Dare generating rod-out block signals to the RMCS. SRM A is reading below the WITHDRAW PERMIT setpoint of 100 cps and is not fully inserted. SRM Dis reading above the UPSCALE setpoint of 1E5 cps. A rod-out block from ANY SRM channel to RMCS generates a RMCS ROD OUT BLOCK to prevent control rod withdrawal.

D is the correct answer. Inserting SRM A will clear the WITHDRAW PERMIT rod-block signal from SRM A to RMCS, and bypassing SRM D will clear the SRM UPSCALE rod-block signal from SRM D.

CONFIDENTIAL Examination Material Page 1 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION A is incorrect. Bypassing SRM D will clear its rod-out block signal to RMCS, but the signal from SRM A remains.

B is incorrect. Inserting SRM A to obtain 1000 cps, per the applicable G0-200-002 guidance, will clear its rod-out block signal to RMCS, but the signal from SRM D remains.

C is incorrect. While placing all IRMs on Range 3 will bypass the WITHDRAW PERMIT rod-out block from SRM A, it will result in a DOWNSCALE trip from all IRMs and a rod-out block signal to RMCS. Bypassing SRM D would clear the rod-out block signal to RMCS, but to no effect.

10CFR55 41.6 Technical References AR-104-E06 AR-104-B06 AR-104-COS G0-100-002 Learning Objectives 1345 Question Source New Previous NRC Exam No Comments KIA sampled on LOC25 NRC exam . This question satisfies the significantly modified critieria of NUREG-1021 ES-401 D.2.f Operations Reviewer mj I 03119114 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 2 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam I RO I Tier I2 I Group 11 I Cognitive Level I High I Level of Difficulty I 3 KIA 205000 K1.08 Shutdown Cooling System (RHR 'Importance ,3.9 Shutdown Cooling Mode)

Statement Knowledge of the physical connections and/or cause-effect relationships between SHUTDOWN COOLING SYSTEM (RHR SHUTDOWN COOLING MODE) and the following: LPCI.

QUESTION 2 Unit 1 is in Mode 3 performing a unit shutdown for a failing Recirc Pump seal.

RHR Loop A has just been placed into Shutdown Cooling using RHR Pump 1A.

The recirc pump seal fails completely. Drywell pressure rises and a RPS trip on high Drywell pressure occurs.

Which one of the following describes the response of RHR?

RHR Loop A RHR Loop B A. RHR Pump 1A tripped Injecting in LPCI alignment RHR SOC isolated B. RHR Pump 1A running in SOC Standby RHR Pump 1C in standby C. RHR Pumps 1A and 1C tripped Running on minimum flow RHR SOC isolated D. RHR Pumps 1A and 1C running Injecting in LPCI alignment in SOC Proposed Answer D Applicant References None Explanation A high Drywell pressure LOCA initiation signal has been received. With reactor pressure below the SOC interlock of 98 psig this results in a LPCI initiation signal to both divisions of RHR. RHR Loop 8 will start, align for LPCI, and inject to the reactor with reactor pressure well below the 430 psig injection valve auto-open permissive. The SOC flowpath is unaffected by Drywell pressure, the only effects on RHR Loop A is that RHR Pump 1C will start in the SOC alignment in addition to RHR Pump 1A and HV-151-FOHA (LPCI o/b inj valve) will receive a full-open signal.

A Incorrect. While RHR Loop 8 will inject in the LPCI alignment, RHR Pump 1A will not receive a trip signal as a SOC isolation does not occur on high OW pressure.

8 Incorrect. RHR Loop 8 will align for and inject in the LPCI mode. RHR Pump 1C will start in the SOC lineup, as the F006C is opened as part of the procedure for placing RHR Loop A in service, regardless of the RHR pump started.

C Incorrect. RHR Loop 8 will align for and inject in the LPCI mode. There is no SOC isolation signal, so neither RHR Loop A pump receives a trip signal.

CONFIDENTIAL Examination Material Page 3 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION D Correct. RHR Pump 1C will start on the high DW pressure /low reactor pressure combination. The RHR Loop A SOC lineup is unaffected by the DW pressure signal.

RHR Loop B will align for and inject in the LPCI mode.

10CFR55 41.7 Technical References OP-149-002 Step 2.1.2.g-l, 2.1.7, 2.6.3.a NOTE Learning Objectives 10766 u Question Source Bank ILO LXR TMOP049/180/002 Previous NRC Exam No Comments Operations Reviewer mj I 06/03/2014 Facility Representative _ _/_ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 4 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam I RO I Tier I2 I Group 11 I Cognitive Level I High I Level of Difficulty I 2 KJA 212000 K2.02 Reactor Protection System I Importance 1 2.1 Statement Knowledge of electrical power supplies to the following: Analog trip system logic cabinets QUESTION 3 Which one of the following identifies the power supply or supplies that if de-energized , would result in venting the scram air header through the Backup Scram Valves SV-147F11 OA and F110B?

A. 1Y201A AND 1Y201 B B. 1Y201AAND1D614 C. 1D614AND1D624 D. 1D614, 0NLY Proposed Answer A Applicant References None Explanation The Backup Scram Valves SV-147110A(B) are energize-to-open, DC-powered solenoid valves that individually provide a redundant means to vent the scram air header on actuation. The valve solenoids are energized by the respective DC power supply 1 D614(624) on a full RPS initiation.

A is the correct answer. De-energization of the RPS Buses 1Y201 A and 1Y201 B removes power from the RPS relay logic cabinets 1C609 and 1C611 and deenergizes the RPS K14x trip relays resulting in a full RPS initiation signal which energizes the Backup Scram Valve solenoids.

B, C and D are all incorrect as loss of DC power to the Backup Scram Valves prevent the valve from actuating.

B is plausible as this is the power supplies to the RPS A trip system and Backup Scram Valve SV-147110A.

C is plausible as this choice represents the loss of power to both divisions of Backup Scram valves.

Dis plausible as this choice is the power supply to Backup Scram Valve SV-147110A and represents incorrect application of the deenergize-to-open operating principle of the scram pilot solenoid valves to the Backup Scram Valves.

10CFR55 41 .7 Technical References M-147 Sht 1 M1-C72-22 Sht 1,12,17 TM -OP-058 Learning Objectives 10072 Question Source New Previous NRC Exam No Comments 3/13 rat. Minor editorial corrections, swapped C&D distractors, based on Ops Reviewer CONFIDENTIAL Examination Material Page 5 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION comments.

Operations Reviewer mj I 03113114 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 6 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam I RO I Tier I 2 I Group 11 I Cognitive Level I Low I Level of Difficulty I 3 KIA 239002 K2.01 Safety Relief Valves I Importance 1 2.8 Statement Knowledge of electrical power supplies to the following: SRV solenoids QUESTION 4 Which one of the following identifies all of the power-operated SRV functions that remain available on a loss of 1D614?

A. ADS initiation Lower Relay Room manual operation B. ADS initiation Control Room manual operation C. Control Room manual operation Remote Shutdown Panel manual operation D. Lower Relay Room manual operation Remote Shutdown Panel manual operation Proposed Answer A Applicant References None Explanation 1D614 supplies power to the normal operation SRV solenoids and the Division 1 ADS logic and associated Division 1 ADS solenoids on the SRVs. The Remote Shutdown Panel handswitches also receive power from 1 D614 to operate the normal operation SRV solenoids of the A, B and C SRVs. Division 2 of ADS is unaffected and upon an automatic or manual ADS initiation will energize the Division 2 ADS solenoids to open the ADS SRVs. The handswitches in the Lower Relay Room are part of the Division 2 ADS logic and will also function to open the SRVs via the Division 2 ADS logic and associated power supply.

A CORRECT. An ADS initiation and manual operation from the Lower Relay Room are still posible on a loss of 1 D614. No other means of electrically operating the SRVs is available.

B Incorrect. Control Room manual operation is not possible as power is lost to the normal operating solenoids and the Control Room handswitches.

C Incorrect. Neither Control Room nor RSDP manual operation is possible as power is lost to the normal operating solenoids and both the Control Room and RSDP handswitches.

D Incorrect. While the ADS SRVs may be operated from the Lower Relay Room, RSDP manual operation is not possible as power is lost to the normal operating solenoids and the RSDP handswitches.

10CFR55 41.7 Technical References E-180 Sht 1 M1-B21-129 Sht4, 5 Learning Objectives 1651 Question Source New Previous NRC Exam No Comments CONFIDENTIAL Examination Material Page 7 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Operations Reviewer _ _I _ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 8 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 4 KIA 259002 K6.05 Reactor Water Level Control System Statement Knowledge of the effect that a loss or malfunction of the following will have on the REACTOR WATER LEVEL CONTROL SYSTEM : Reactor water level input QUESTION 5 Use your provided references to answer this question.

Unit 1 is operating at rated power.

The following reactor level indications are observed on the 1C652 Standby Information Panel.

Narrow Range A +31 in, down slow Narrow Range B +39 in , up slow Narrow Range C +31 in , down slow Wide Range +18 in, down slow Narrow Range (XR-10602) +35 in, steady Upset Range (XR-10602) +32 in, down slow Wide Range indications on 1C601 also show +18 in, down slow.

Which one of the following identifies ill! correct level indication(s) in these conditions?

A. Narrow Range B B. Upset Range (XR-10602)

Wide Range C. Narrow Range A and C Wide Range D. Narrow Range A and C Upset Range (XR-10602)

Wide Range Proposed Answer D Applicant References ON-145-001 Att A Explanation The indications provided are consistent with a slow failure high of the Narrow Range B (NRLBB) signal in the Feedwater Level Control System. The signal has not yet drifted high enough for it to be flagged as DEVIANT, so the FWLC Average Level input is still taken from NRLA and NRLBB and the low median level. FWLC Selected Level remains Average Level. The XR-10601 NR indication is the FWLC Selected Level. Because of the simple arithmetic average as NRLBB drifts up FW flow is reduced to return Average Level to the FWLC setpoint of +35",

resulting in all valid reactor level indicators slowly indicating lower as FW flow to the reactor is reduced.

A Incorrect. Narrow Range 8 has drifted high. The other level indications provided are associated with both the C004 and COOS instrument racks, eliminating a common-mode failure due to variable/reference leg leaks or condensing chamber issues.

CONFIDENTIAL Examination Material Page 9 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION B Incorrect. While UR and WR are correct, NR A and C are also correct.

C Incorrect. While NR A and C, and WR, are all correct, UR is also correct.

D CORRECT. NR A and C, UR, and WR indications are all correct for the given conditions.

10CFR55 41 .7 Technical References ON-145-001 Section 2.0 Learning Objectives 15999 Question Source New Previous NRC Exam No Comments Operations Reviewer mj I 03119114 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 10 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 3 KIA 211000 K3.01 Standby Liquid Control System Statement Knowledge of the effect that a loss or malfunction of the STANDBY LIQUID CONTROL SYSTEM will have on following : Ability to shutdown the reactor in certain conditions QUESTION 6 Unit 1 experienced a high-power A TWS .

Standby Liquid Control Pump A was started .

A local operator reports that the pump discharge relief valve lifted and is stuck open.

Which one of the following describes the availability of SLC to inject boron to shutdown the reactor under these conditions?

A Boron tank contents are being lost to Radwaste B. Boron is being injected to the reactor at a reduced flowrate C. SLC Pump B must be started to inject boron to the reactor D. Boron can be injected to the reactor with RCIC , ONLY Proposed Answer c Applicant References None Explanation Each SLC pump is provided with a discharge pressure relief valve located between the pump and its discharge check valve. The relief valve returns to the pump suction and is capable of passing full flow from the pump.

A Incorrect. All flow from SLC Pump A is being returned to the pump suction via the lifted relief valve.

B Incorrect. All flow from SLC Pump A is being returned to the pump suction via the lifted relief valve.

C Correct. The SLC Pump A discharge check valve will seat to prevent flow from SLC Pump B passing through the open SLC Pump A relief valve. Starting SLC Pump B fires the 2nd squib valve creating a second flow path out of the SLC system to the reactor.

D Incorrect. The SLC Pump A discharge check valve will seat to prevent flow from SLC Pump B passing through the open SLC Pump A relief valve. The B squib valve can be fired to create a second flow path. Use of RCIC is not required.

10CFR55 41 .6 Technical References M-148 Learning Objectives 10887j Question Source Bank ILO LXR TMOP053/1214/006 Previous NRC Exam No Comments CONFIDENTIAL Examination Material Page 11 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Operations Reviewer mj I 0610312014 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 12 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 3 KJA 263000 K4.02 D.C. Electrical Distribution Statement Knowledge of D.C. ELECTRICAL DISTRIBUTION design feature(s) and/or interlocks which provide for the following: Breaker interlocks, permissives, bypasses and cross-ties QUESTION 7 The Class 1E 125V DC system automatically provides an alternate control power supply to select ESS Bus breakers to ensure LOOP/LOCA load shed occurs.

Which one of the following identifies loads that have the alternate power supply?

A. ESW Pump C ESW Pump D RHRSW Pump 1A RHRSW Pump 1B B. ESWPumpA ESWPump B RHRSW Pump 2A RHRSW Pump 2B C. CRD Pump 1B CRD Pump 2B RHR Pump 1D RHR Pump 2D D. Core Spray Pump 1C Core Spray Pump 1D RHRSW Pump 1A RHRSW Pump 1B Proposed Answer A Applicant References None Explanation The alternate breaker trip power supply logic is provided to ensure that specific loads are shed to prevent overloading a Diesel Generator when re-energizing its respective bus during a LOOP/LOCA with a failure of the 1D620 DC power supply. The alternate trip power is interlocked with the normal breaker control power to ensure the 2 DC sources are not cross-tied.

A Correct. These breakers required redundant trip capability.

B Incorrect. These are the equivalent 1A/1 Band 2A/2B ESS Bus loads.

C Incorrect. While CRD Pumps 1B and 2B have the redundant trip power, no ECCS pumps do.

D Incorrect. While RHRSW Pumps 1A and 1B have the redundant trip power, no ECCS pumps do.

10CFR55 41.7 CONFIDENTIAL Examination Material Page 13 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Technical References ON-102-610,620 TM-OP-002 Learning Objectives 11859 e Question Source Bank ILO LXR TMOP0021101441008 Previous NRC Exam No Comments Operations Reviewer _ _I _ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 14 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 3 KIA 218000 K4.02 Automatic Depressurization System Statement Knowledge of AUTOMATIC DEPRESSURIZATION SYSTEM design feature(s) and/or interlocks which provide for the following: Allows manual initiation of ADS logic QUESTION 8 Unit 2 experienced a loss of all high-pressure reactor injection systems.

Both divisions of ADS were inhibited when the ADS logic timer alarms initiated without a valid initiation signal present.

Subsequently, a Rapid Depressurization on low reactor water level is required.

All low-pressure ECCS systems respond as designed.

Which one of the following identifies the action(s) required, if any, to immediately initiate ADS from the Control Room using the arm-and-depress pushbuttons?

A ADS can be manually initiated immediately with no additional action B. Start at least 1 RHR or 2 Core Spray pumps in a division C. Un-inhibit ADS D. Start at least 1 RHR or 2 Core Spray pumps in each division AND Un-inhibit ADS Proposed Answer A Applicant References None Explanation ADS has been inhibited due to an unspecified logic malfunction. Subsequently, reactor level has fallen below -161" requiring Rapid Depressurization. The ECCS initiation at -129" will start all low-pressure ECCS pumps and provide a valid initiation signal to ADS after a time delay.

A Correct. ADS can be manually initiated as long as 1 RHR or 2 Core Spray pumps in the associated division are running , which is the case as level has fallen below the -129" ECCS initiation setpoint. Depressing the manual initiation PB will result in immediate actuation of ADS and opening SRVs.

B Incorrect. The required pumps are already running due to reactor level< -129".

C Incorrect. This will initiate ADS, but after a 105-second time delay at minimum, and potentially significantly longer if a high DW pressure signal is not present and the -129" reactor level low timer to bypass the required DW pressure signal has only recently initiated.

D Incorrect. The required pumps are already running and the manual initiation PBs are not affected by the ADS inhibit keyswitch.

10CFR55 41 .7 Technical References M1-B21-102 Sht 204 CONFIDENTIAL Examination Material Page 15 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Learning Objectives 2105 a,b Question Source Bank LXR LOR TMOP083EI21 051005 Previous NRC Exam No Comments Operations Reviewer mj I 0612312014 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 16 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 3 KJA 215003 K5.01 Intermediate Range Monitor (IRM) System Statement Knowledge of the operational implications of the following concepts as they apply to INTERMEDIATE RANGE MONITOR (IRM) SYSTEM : Detector operation QUESTION 9 Unit 1 is starting up, with IRMs on Range 1 and 2.

Engineering just reported that the high-voltage power supplies on the Division 2 IRMs were mis-calibrated during the outage.

The Division 2 IRMs are operating with detector voltages set to the SRM voltage.

Which one of the following describes the operational implications for the Division 2 IRMs?

A. Will eventually fail upscale as reactor power is raised to enter Mode 1 B. Are reading higher than Division 1 IRMs C. Are reading lower than Division 1 IRMs D. No effect from detector voltage error, as IRMs are ionization detectors Proposed Answer B Applicant References None Explanation The Division 2 IRMs are operating at a higher voltage than normal, at the same voltage as a SRM. The SRMs operate in the proportional region of the gas-filled detector curve. The reading from IRMs operating at the higher detector voltage will be higher than those operating at the correct voltage.

A Incorrect. IRM detectors have lower-enriched uranium and a lower gas pressure. With one division of IRMs inoperable, LCO requirements for the IRM function are not satisfied and power ascension will be limited. It will take more than the 12 hours1.388889e-4 days <br />0.00333 hours <br />1.984127e-5 weeks <br />4.566e-6 months <br /> allowed by the RPS TS to raise reactor power sufficiently to make the SRMs fail upscale. IRM readings at Mode 1 are typically on Range 10, and well below the upscale alarm setpoint.

B Correct. The higher applied voltage on the Division 2 IRM detectors will result in significantly higher readings from these detectors, substantially higher than the Division 1 detectors.

C Incorrect. The higher applied voltage on the Division 2 IRM detectors will result in significantly higher readings from these detectors, substantially higher than the Division 1 detectors. This distractor represents a misconception about whether the IRMs or SRMs operate at the higher voltage required to place the detector in the proportional region of the gas-filled detector curve.

D Incorrect. The nominaiiRM voltage of 100 VDC is such that the IRMs operate in the ionization region of the gas-filled detector curve. The 350 VDC applied to an IRM will result in the detector entering the proportional region of the GFDC.

10CFR55 41.2 Technical References TM-OP-0788 CONFIDENTIAL Examination Material Page 17 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Learning Objectives 2337 c Question Source New Previous NRC Exam No Comments Operations Reviewer _ _I _ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 18 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 2 KIA 206000 K5.02 High Pressure Coolant Injection System Statement Knowledge of the operational implications of the following concepts as they apply to HIGH PRESSURE COOLANT INJECTION SYSTEM : Turbine shaft sealing: BWR-2,3,4 QUESTION 10 Unit 2 scrammed from rated power due to a loss of offsite power.

Both trains of Standby Gas Treatment System fail to start and cannot be manually started .

Which one of the following identifies the operational implications of placing HPCI in pressure control for these conditions?

A. Becomes air-bound due to the buildup of non-condensible gases B. Isolates on turbine exhaust diaphragm rupture C. Isolates on high room temperature D. HPCI room radiation levels rise Proposed Answer D Applicant References None Explanation SGTS accepts the discharge of the HPCI barometric condenser vacuum pump. This pump functions on a HPCI initiation signal to draw a slight vacuum on the HPCI barometric condenser tank to aid in condensing steam drains. With no flowpath to SGTS a pressure relieving valve will direct the discharge of the pump back to the barometric condenser.

Collection of steam drains will be affected, but HPCI operability is not affected.

A Incorrect. Collection of non-condensible gases in the HPCI main steam supply will not result in the turbine or HPCI pump becoming air-bound.

B Incorrect. Additional moisture may be present in the HPCI turbine steam lines, which could carry into the turbine and exhaust. However, the steam drains will still function to remove moisture, albeit at a degraded efficiency. No concern exists for overpressurization of the HPCI turbine exhaust due to moisture.

C Incorrect. Steam leakage from the HPCI turbine seals will rise, but the HPCI isolation on high room temperature is sized for a 25 gpm steam leak.

D Correct. Steam leakage from the HPCI turbine seals will rise, resulting in increased transport of radioactive gases from the main steam supply into the HPCI room.

10CFR55 41.7 Technical References TS 3.5.1 Bases TM-OP-052 M-156 Sht 1 Learning Objectives 11255 e Question Source Bank ILO LXR TMOP052/2037/007 Previous NRC Exam No CONFIDENTIAL Examination Material Page 19 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Comments Operations Reviewer _ _I _ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 20 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 2 KIA 262002 K6.02 Uninterruptable Power Supply (A.C./D.C.)

Statement Knowledge of the effect that a loss or malfunction of the following will have on the UNINTERRUPTABLE POWER SUPPLY (A.C./D.C.) : D.C. electrical power QUESTION 11 Which one of the following identifies the effect on Vital UPS 1D666(2D666) of a loss of the Division 2 250 VDC bus 1D662(2D662)?

Unit 1 - 1D666 Unit 2 - 2D666 A. Transfers to ALTERNATE Transfers to ALTERNATE B. Transfers to ALTERNATE Remains on PREFERRED C. Remains on PREFERRED Transfers to ALTERNATE D. Remains on PREFERRED Remains on PREFERRED Proposed Answer B Applicant References None Explanation The Vital UPS inverter 1D666 is supplied from Class 1E 250V DC bus 1D662. The Unit 2 Vital UPS inverter, 2D666, is supplied from a separate non-Class 1E 250V DC battery, 2D142.

A Incorrect. Unit 2 Vital UPS is powered from 2D142.

B Correct. The 1D666 static switch will automatically transfer to the ALTERN ATE supply on undervoltage. 2D666 remains on the PREFERRED source as its supply is unaffected by 2D662.

C Incorrect. This choice represents misapplication of the unit difference to Unit 2.

D Incorrect. While 2D666 remains on the preferred source, 1D2666 does not. This is a plausible distractor as the Computer UPS 1D656 is supplied from the Division 1 250 VDC bus.

10CFR55 41.4 Technical References ON-1 (2)88-001 TM-OP-017 Learning Objectives 10174 Question Source New Previous NRC Exam No Comments Operations Reviewer _ _I_ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 21 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION BLANK PAGE CONFIDENTIAL Examination Material Page 22 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 2 KJA 217000 K6.04 Reactor Core Isolation Cooling System Statement Knowledge of the effect that a loss or malfunction of the following will have on the REACTOR CORE ISOLATION COOLING SYSTEM (RCIC): Condensate storage and transfer system QUESTION 12 Unit 1 is operating at rated power.

A leak develops on the Condensate Storage Tank.

Annunciator RCIC CONDENSATE STORAGE LOW LEVEL (AR-108-E01) is in alarm.

Which one of the following describes the response of RCIC to this alarm?

A. No actions occur until annunciator CONDENSATE TANK A HI-LO LEVEL (AR-016-DO?)

alarms B. HV-149-F031, PUMP SUCT FROM SUPP POOL, opens AND simultaneously HV-149-F010, PUMP SUCT FROM CST, closes C. HV-149-F031, PUMP SUCT FROM SUPP POOL, opens THEN HV-149-F010, PUMP SUCT FROM CST, closes D. HV-149-F010, PUMP SUCT FROM CST, closes AND HV-149-F031, PUMP SUCT FROM SUPP POOL, opens WHEN a RCIC initiation signal is received Proposed Answer c Applicant References None Explanation A RCIC suction swap is initiated when the RCIC low CST level alarm is received at 43.5" CST level. The suction swap occurs by the F031 automatically opening in response to the low CST level signal, followed by closure of the F010 once the F031 is full open.

A Incorrect. The CST high-low level alarm is indicative of an abnormal CST level nearer the normal operating range (19' 8"), well above the level at which the RCIC low CST alarm is received.

B Incorrect. The suction swap is initiated with an OPEN signal to the F031 valve. The F031 FULL OPEN initiates a closure signal to the F010.

C Correct. The F031 valve receives an open signal on low CST level at the alarm setpoint.

The F010 closes once the F031 is full open.

D Incorrect. A RCIC initiation signal is not required to generate an open signal to the F031, it open directly on the low CST level signal.

10CFR55 41.7 CONFIDENTIAL Examination Material Page 23 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Technical References OP-150-001 Section 2.2 AR-108-E01 Learning Objectives 11244 Question Source New Previous NRC Exam No Comments Operations Reviewer _ _I _ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 24 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 3 KIA 400000 A1.01 Component Cooling Water System Statement Ability to predict and I or monitor changes in parameters associated with operating the CCWS controls including: CCW flow rate QUESTION 13 Both units are operating at rated power.

S0-054-A03, Quarterly ESW Flow Verification Loop A , is in progress, with ESW Pump A and C running .

Which one of the following ESW loads, if isolated, would require securing an ESW Pump to avoid pump damage due to potential overheating?

A. Unit 1 OR Unit 2 Reactor Building B. Any Diesel Generator aligned for standby service C. 2 or more Diesel Generators aligned for standby service D. BOTH Control Structure Chillers Proposed Answer c Applicant References None Explanation ESW minimum flow requirements are normally maintained by having the flow paths for all loads valved in. Having both pumps running in a loop requires consideration of pump minimum flow only if more than 1 large load is isolated, per OP-054-001 Step 2.1 .2.d. Large loads are defined as either Unit 1 or 2 Reactor Buildings or any Diesel Generator.

A Incorrect. This is only 1 large load.

B Incorrect. This is only 1 large load.

C Correct. ESW isolated to 2 or more DG aligned for standby service constitutes more than 1 large load per Step 2.1.2.d of OP-054-001 .

D Incorrect. This is the 2nd largest individual ESW load that can be valved in.

10CFR55 41 .8 Technical References OP-054-001 Step 2.1.2.d, Att A Learning Objectives 10812 Question Source New Previous NRC Exam No Comments Operations Reviewer _ _I _ __ Facility Representative lnit I date lnit I date CONFIDENTIAL Examination Material Page 25 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION BLANK PAGE CONFIDENTIAL Examination Material Page 26 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam I RO I Tier I 2 I Group 11 I Cognitive Level I High I Level of Difficulty I 2 KIA 203000 A1.09 RHRILPCI: Injection Mode I Importance 1 2.9 Statement Ability to predict and/or monitor changes in parameters associated with operating the RHRILPCI:

INJECTION MODE (PLANT SPECIFIC) controls including: Component cooling water systems QUESTION 14 Both units are operating at rated power.

A spurious initiation of Unit 1 RHR Loop B occurs due to a fault in the manual initiation pushbutton.

Which one of the following identifies the RHR Pumps running on Unit 1, and which pump motor oil coolers have cooling water from ESW?

RHR Pumps running RHR Pumps with ESW cooling A. All All B. All RHR Pumps 1B, 1C, 1D C. RHR Pumps 1B, 1D RHR Pumps 1B, 1C, 10 D. RHR Pumps 1B, 1D None Proposed Answer A Applicant References None Explanation A LPCI initiation signal has been received on Unit 1 Division 2 RHR. Due to the cross-divisional initiation logic, this is equivalent to a full initiation signal to both divisions of LPCI.

All 4 RHR pumps receive a start signal and started after their respective time delays. Diesel Generators C and D receive start signals from the divisional LPCI logic. The start of DG C and D will result in starts of the associated C and D ESW Pumps.

A Correct. All 4 RHR pumps are running on Unit 1 as a result of the Div 2 LPCI initiation.

With ESW C and D running ESW is being supplied to all 4 RHR Pump oil coolers.

B Incorrect. This represents an assumption that the DG start signal comes from the respective divisional LPCIIogic, and reflects that the RHR Pump 1C oil cooler is cooled from both ESW loops, so that RHR Pump 1C oil cooler receives cooling from ESW B.

C Incorrect. All 4 RHR pumps will be running due to the cross-divisional initiation logic.

This choice does reflect that the RHR Pump 1C oil cooler is cooled from both ESW loops.

D Incorrect. All 4 RHR pumps will be running due to the cross-divisional initiation logic, and both loops of ESW will have at least 1 pump running to supply cooling.

10CFR55 41.7 Technical References M-111Sht2,3 M1-E11-66 Sht 4 M1-E21-20 Sht 3 TM-OP-054 Learning Objectives 10805 h CONFIDENTIAL Examination Material Page 27 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Question Source Bank ILO LXR TMOP0491181122 Previous NRC Exam No Comments Operations Reviewer _ _I _ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 28 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 4 KIA 223002 A2.05 Primary Containment Isolation System/Nuclear Steam SupplyShut-Off Statement Ability to (a) predict the impacts of the following on the PRIMARY CONTAINMENT ISOLATION SYSTEM/NUCLEAR STEAM SUPPLY SHUT-OFF; and (b) based on those predictions, use procedures to correct, control, or mitigate the consequences of those abnormal conditions or operations: Nuclear boiler instrumentation failures QUESTION 15 Unit 1 is operating at rated power.

While I&C is restoring from a channel calibration, ALL Wide Range level indications on the 1C004 panel momentarily lower, to approximately -50", then return to normal.

Which one of the following identifies one effect of the transient, and the operator action required in response?

A. Both Reactor Recirculation Pumps trip Immediately place the Mode switch to SHUTDOWN B. Reactor Bldg Chilled Water is isolated to the Recirc Pump Motor Coolers Reset the NSSSS and RBCW isolation logics and reopen the RBCW supply valves C. RBCCW is isolated to the Recirc Pump Motor Coolers Reset the NSSSS and RBCCW isolation logics and reopen the RBCCW supply valves D. Reactor Bldg Chilled Water is isolated to the Drywell Coolers Fully open the RBCCW TCV to maximize Drywell cooling Proposed Answer B Applicant References None Explanation ON-145-004 Table 2 shows the Wide Range level indications located on the 1C004 panel. A momentary spike to -50" will result in a Level 2 trip at -38" .

A Incorrect. There are 2 possible methods of tripping the recirc pumps on the -38" signal.

ATWS-RPT trips the recirc pumps at -38", but the logic is A+C or B+D to trip the respective trip systems. The A and B channels of the N025 level instruments are affected. The 2nd possible method is due to loss of cooling, but manual action is required there are no automatic trips of the recirc pumps on high pump motor temperature. The M-G set motors do have a direct high motor temperature trip.

B Correct. The trip of the A and B channels of the N026 level instruments will result in isolation of RBCW to the Recirc Pump motor coolers via the NSSSS -38" isolation logic.

The NSSSS and RBCW isolation logics must be reset and the valves reopened to restore cooling.

C Incorrect. RBCCW is supplied to the Recirc Pump bearing and seal coolers, not the motor coolers. RBCCW isolates to the Drywell on a Level 1 isolation signal.

D Incorrect. RBCW does isolate to the Drywell coolers, and the specified malfunction would satisfy the logic, but the setpoint is Level1 (-129").

CONFIDENTIAL Examination Material Page 29 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION 10CFR55 41.7 Technical References ON-145-004 Table 2, ON-159-002 Att B E-184 Sht 1 E-216 Sht 11,29 M1-B21-131 Sht 7, 10 TM-OP-0598, TM-OP-080 Learning Objectives 11307 h Question Source New Previous NRC Exam No Comments Operations Reviewer mj I 0610312014 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 30 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 2 KJA 215005 A2.02 Average Power Range Monitor/Local Power Range Monitor Statement Ability to (a) predict the impacts of the following on the AVERAGE POWER RANGE MONITOR/LOCAL POWER RANGE MONITOR SYSTEM ; and (b) based on those predictions, use procedures to correct, control, or mitigate the consequences of those abnormal conditions or operations: Upscale or downscale trips QUESTION 16 Unit 1 is shutting down for a planned outage. Reactor power is 12 percent.

Improved BPWS Control Rod Insertion is being used.

Insertion of a number of high-worth control rods results in a rapid power reduction. Reactor power is 5 percent when control rod insertion is halted.

Which one of the following identifies the next action to be performed, and why?

A. Continue inserting control rods per the shutdown sequence An unrecognized re-criticality can occur if control rod insertion is stopped B. Withdraw control rods to raise core power to approximately 10 percent Reactor power is too low for operation with the Mode switch in RUN C. Place the Mode switch to SHUTDOWN Unrecognized re-criticality can occur and continued control rod insertion is blocked D. Place the Mode switch to STARTUP Clear the control rod withdrawal block by the APRMs Proposed Answer D Applicant References None Explanation With reactor power initially at 12 percent, power is too high to have placed the Mode switch in STARTUP. Per G0-100-004 Step 5.33.9 the Mode switch is not placed to STARTUP until approximately 10 percent power. The next step required by the GO will be to place the Mode switch in STARTUP to clear the APRM downscale control rod withdrawal block at 5 percent power.

A Incorrect. Un-recognized criticality does not become a concern until power is less than 3 percent or if subcriticality is confirmed.

B Incorrect. Control rod withdrawal is blocked by the APRM downscale at 5 percent.

C Incorrect. Un-recognized criticality does not become a concern until power is less than 3 percent. Control rod insertion is not blocked, the APRMs are only generating a withdrawal block, the RWM is bypassed for Improved BPWS.

D Correct. The APRMs are generating a control rod withdrawal block that can only be cleared by placing the Mode switch to STARTUP.

10CFR55 41.6 CONFIDENTIAL Examination Material Page 31 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Technical References G0-1 00-004 Step 5.33 AR-104-H03 Learning Objectives 15716 Question Source New Previous NRC Exam No Comments Operations Reviewer _ _I _ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 32 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam I RO I Tier I2 I Group I 1 I Cognitive Level I Low I Level of Difficulty I 3 KIA 264000 A3.04 Emergency Generators (Diesel/Jet) I Importance 1 3.1 Statement Ability to monitor automatic operations of the EMERGENCY GENERATORS (DIESEUJET) including:

Operation of the governor control system on frequency and voltage control QUESTION 17 Diesel Generator A was being tested at rated load when it tripped due to a spurious high vibration condition .

Diesel Generator trips have been reset per ON-024-001, Diesel Generator Trip.

The Auto Voltage Regulator has NOT been adjusted since the DG tripped .

A test run of the DG is to be performed to demonstrate operability, syncing to ESS Bus 1A.

Which one of the following describes the Control Room indication expected to be observed if the DG is started for the test run without adjusting the Auto Voltage Regulator?

A. Diesel Generator low-priority trouble alarm DG A volts steady at nominal 4KV B. Diesel Generator low-priority trouble alarm DG A volts steady at approximately 4.5KV C. Diesel Generator high-priority trouble alarm DG A volts steady at nominal 4KV D. Diesel Generator high-priority trouble alarm DG A volts at 0 KV Proposed Answer D Applicant References None Explanation ON-024-001 for resetting a DG trip contains a requirement to run the auto voltage regulator setpoint to minimum when resetting a DG trip in preparation for a retest of the engine. This ensure the minimum field current and terminal voltage on the restart. Voltage regulator setup will take place as part of a test run during generator synch and loading/unloading.

Without adjustment of the voltage regulator following a DG trip from full load, an overvoltage trip is expected on subsequent restart of the engine.

A Incorrect. This describes operation of the DG as for a normal trip reset.

B Incorrect. This describes continued operation of the DG with elevated voltage, as expected for a change in generator field.

C Incorrect. The overvoltage trip will result in a high-priority DG alarm and trip of the DG.

D Correct. An overvoltage trip will generate a high-priority DG alarm and the DG will trip.

Voltage indication goes to 0 on a overvoltage trip.

10CFR55 CONFIDENTIAL Examination Material Page 33 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Technical References ON-024-001, Step 3.9, 5.0 LA-0521-806, AR-015-81 0 Learning Objectives 11273 f Question Source New Previous NRC Exam No Comments The KJA was interpreted to include the voltage regulator in addition to the governor due to the failure to reference voltage regulation in the A3 KJA and the importance of the tested concept atSSES.

Operations Reviewer _ _I _ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 34 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 2 KIA 262001 A3.02 A.C. Electrical Distribution Statement Ability to monitor automatic operations of the A. C. ELECTRICAL DISTRIBUTION including : Automatic bus transfer QUESTION 18 Refer to the control panel mimic on the following page when answering this question.

Unit 1 is operating at rated power, Unit 2 is shutting down, in Mode 2.

An electrical transient occurs.

No operator action occurred after the transient.

The final electric plant lineup is shown on the illustration on the following page.

Which one of the following correctly describes the events that led to the electric plant lineup shown?

A. Startup Bus 20 experienced a lockout condition B. Transformer T-20 experienced a lockout condition C. Startup Bus 20 breaker to Tie Bus OA 107, OA 104-03, tripped when Tie Breaker OA 105-02 closed D. Startup Bus 20 feeder breakers tripped on overcurrent when Aux Bus 12B was transferred to Tie Bus OA 107 CONFIDENTIAL Examination Material Page 35 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION

[Insert sim panel mimic display]

Proposed Answer A Appl icant References None Explanation The electric plant lineup show is that obtained following a Startup Bus 20 lockout, when starting in the normal lineup with the Unit 2 Main Generator offline and the Unit 2 Aux Buses transferred to the Tie Bus.

A Correct. On the SUB20 lockout, the feeder breaker from T-20, OA104-01, and the SUB20 feeder to Tie Bus OA107, OA104-03, open . The de-energization of Tie Bus OA107 initiates a closure signal to the Tie Breaker, OA015-02 to close. The Tie Breaker permissive to close is met as the Unit 2 Aux Bus 12A and 12B feeder breakers are closed but OA104-03 is open. The Tie Breaker closes, re-energizing Tie Bus OA107 and the Unit 2 Aux Buses.

B Incorrect. On a T-20 lockout the SUB20 breaker to Tie Bus OA107, OA104-03, remains closed. OA104-01 opens, as well as MOAB 2R105. High Speed Ground Switch 2R106 closes.

C Incorrect. This distractor is plausible as the Tie Bus auto-closure permissive is that OA104-03 be open. This distractor represents translation of this starting permissive into an automatic action on an attempted closure of the Tie Breaker. The Tie Breaker would remain open and no automatic closure signal would be generated, with a Unit 2 Aux Bus fed from OA107 and OA104-03 closed.

D Incorrect. This distractor is plausible for a bus overcurrent condition. However the manual transfer of the Aux Buses was completed successfully, as indicated by the matched semaphores on both Aux Bus feeders from the Unit 2 Main Generator, 2A101-01 and -02.

10CFR55 41 .7 Technical References ON-003-002 Step 2.10 Learning Objectives 11779 I Question Source New Previous NRC Exam No Comments Operations Reviewer _ _I _ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 36 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 4 KJA 300000 A4.01 Instrument Air System (lAS)

Statement Ability to manually operate and I or monitor in the control room: Pressure gauges QUESTION 19 Refer to the control panel mimic on the following page when answering this question.

Two indications of Instrument Air pressure are provided on 1C668 in the Control Room:

PI-12511A, INSTR AIR PRESS Pl-12564 , INSTR AIR HDR PRESS Which one of the following identifies the indications that most closely correspond to (1) the pressure at which Instrument Air compressor loading is controlled?

(2) the pressure at which the Service Air cross-tie will open?

Compressor Loading Service Air Cross-Tie A. INSTR AIR HDR PRESS INSTR AIR HDR PRESS B. INSTR AIR HDR PRESS INSTR AIR PRESS C. INSTR AIR PRESS INSTR AIR PRESS D. INSTR AIR PRESS INSTR AIR HDR PRESS CONFIDENTIAL Examination Material Page 37 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Proposed Answer B Appl icant References None Explanation The Control Room is provided with 2 indications of Instrument Air pressure for each unit.

Compressor loading is controlled by the PSL-12508x series of pressure switches. These sense Instrument Air pressure downstream of the Instrument Air Dryers. The INSTR AIR HDR PRESS from Pl-1(2)2564 is sensed in the Turbine Building instrument air header.

Service Air cross-tie from PCV-12560 connects to Instrument Air immediately downstream of the Instrument Air receivers. This is where the INSTR AIR PRESS from PI-1(2)2511A is sensed.

A Incorrect. The pressure at which the S/A cross-tie will open most closely corresponds to INSTR AIR PRESS.

B Correct. The 1/A compressors are controlled by 1/A pressure downstream of the 1/A Dryers. This most closely corresponds to INSTR AIR HDR PRESS. The pressure at which the S/A cross-tie will open most closely corresponds to INSTR AIR PRESS.

C Incorrect. The IIA compressors operating pressure most closely corresponds to INSTR AIR HDR PRESS.

D Incorrect. The 1/A compressors operating pressure most closely corresponds to INSTR AIR HDR PRESS. The pressure at which the S/A cross-tie will open most closely corresponds to INSTR AIR PRESS.

CONFIDENTIAL Examination Material Page 38 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION 10CFR55 41.4 Technical References M-125 Sht 1,2,3,20 Learning Objectives 10588 b Question Source New Previous NRC Exam No Comments Operations Reviewer _ _I _ __ Facility Representative _ _I_ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 39 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION BLANK PAGE CONFIDENTIAL Examination Material Page 40 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 3 KIA 261000 A4.04 Standby Gas Treatment System Statement Ability to manually operate and/or monitor in the control room: Primary containment pressure QUESTION 20 Unit 1 is starting up from a forced outage.

Suppression Chamber inerting is in-progress using Standby Gas Treatment System A.

HD-17508A, DRWLIWETWELL BURP DMP, fails closed.

Which one of the following identifies ...

(1) the effect of the damper closure if no operator action is taken?

(2) the appropriate operator action to initiate in response to the failure?

A. Primary containment pressure will rise until the reactor scrams on high Drywell pressure Terminate the purge by closing HV-15721, CONTN N2 PURGE OB ISO B. Primary containment pressure will rise until the reactor scrams on high Drywell pressure Place SGTS Bin-service and open HD-17508B, DRWLIWETWELL BURP DMP C. Primary containment pressure will rise until Drywell pressure reaches 1 psig Terminate the purge by closing HV-15721, CONTN N2 PURGE OB ISO D. Primary containment pressure will rise until Suppression Chamber pressure reaches 1 psig Place SGTS Bin-service and open HD-17508B, DRWLIWETWELL BURP DMP Proposed Answer c Applicant References None Explanation A N2 purge of the Suppression Chamber is in progress. The SC is being vented to the common SGTS suction by the HD-17508A and B dampers in series. When the HD-17508A fails closed, venting of the SC via SGTS is no longer possible and SC pressure will begin to rise.

When SC pressure is 0.5 psig above Drywell pressure, the OW vacuum reliefs will lift, allowing the SC to vent to the DW and raising DW pressure. SC chamber pressure will continue to rise as long as the N2 supply path is open, so DW pressure will rise, lagging SC pressure by approximately 0.5 psig.

A Incorrect. When Drywell pressure reaches 1 psig the N2 purge supply isolation valve, HV-15721, will automatically close. With the vent path isolated by the HD-17508A failure, SC and DW pressure will remain constant, with the OW at approximately 1 psig, well below the 1.72 psig scram setpoint.

B Incorrect. As noted Drywell pressure will not exceed 1 psig. The HD-17508A is in series with the HD-175088. The lineup is not 1 valve to each SGTS train.

CONFIDENTIAL Examination Material Page 41 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION C Correct. When Drywell pressure reaches 1 psig the N2 purge supply isolation valve, HV-15721, will automatically close. With the vent path isolated by the HD-17508A failure, SC and OW pressure will remain constant, with the OW at approximately 1 psig, well below the 1.72 psig scram setpoint. The containment pressurization transient may be terminated by closing the N2 makeup valve HV-15721 (refer to AR-112-003).

D Incorrect. The HD-17508A is in series with the HD-175088. The lineup is not 1 valve to each SGTS train.

10CFR55 41 .9 Technical References OP-173-001 Section 2.1 AR-112-003 M-157 Sht 1 V-175 Sht 29, E-192 Sht 19 TM-OP-070 Learning Objectives 11181 Question Source New Previous NRC Exam No Comments Operations Reviewer _ _I _ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 42 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 2 KIA 209001 2.4.46 Low Pressure Core Spray System Statement Emergency Procedures I Plan -Ability to verify that the alarms are consistent with the plant conditions.

QUESTION 21 Unit 1 experienced a condition in the Secondary Containment requiring Rapid Depressurization.

Core Spray Pumps 1A and 1C were manually started for reactor level control.

Annunciator RHR INJ PERMISSIVE LOOP A RX LO PRESS (AR-109-A05) is clear.

Reactor pressure is 400 psig, down slow.

Which one of the following describes the preferred method to open HV-152-F005A, CORE SPRAY LOOP A IB INJ SHUTOFF, and inject with Core Spray Loop A under these conditions?

A. Wait until reactor pressure lowers below 230 psig and AR-109-A05 goes into alarm ,

THEN open HV-152-F005A using the Control Room handswitch B. Arm and depress the CORE SPRAY LOOP A MAN INIT pushbutton C. Place LO RX PRESS PERM on the 1C601 Core Spray Loop A control panel to BYPASS, THEN open HV-152-F005A using the Control Room handswitch D. Dispatch NPOs to locally open the HV-152-F005A manually Proposed Answer c Applicant References None Explanation Following a Rapid Depressurization with a loss of Condensate, reactor level will be low with HPCI and RCIC isolated on low reactor pressure and unavailable to restore reactor level. The conditions presented in the stem stipulate that reactor pressure has fallen below the ECCS low-pressure injection permissive, but reactor level has not lowered to the ECCS automatic initiation setpoint as alarms AR-109-802 (CS A actuated), -803 (ECCS hi DW press( and -804 (ECCS low reactor level) are all clear.

A Incorrect. Reactor pressure of 400 psig satisfies the auto-open permissive for the Core Spray F005 injection valve. The 230 psig is a plausible value for the setpoint for the permissive alarm as it is just below the 236 psig setpoint for the auto-closure setpoint for the Recirc Pump discharge valve automatic closure for LPCI injection.

8 Incorrect. Arming and depressing the CS A manual initiation pushbutton is not preferred, as this action will result in a loss of Drywell cooling and subsequent entry into E0-1 03. OP-AD-004 Att A, V.A.3 directs the operator to take action to initiate ECCS injection prior to the auto-initiation setpoint. Performance of a component-by-component start of CS satisfies this direction.

C Correct. Placing the App R bypass in service bypasses the F005A interlock with the F004A. An ECCS initiation signal is not present to generate an auto-open signal.

OP-151-001 Section 2.3.4 provides direction for operation of the App R bypass.

D Incorrect. Operation from the Control Room is possible.

CONFIDENTIAL Examination Material Page 43 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION 10CFR55 41.7 Technical References E-155 Sht 12 OP-151-001 Section 2.3.4 OP-AD-004 Att B,Section V Learning Objectives 10387 c Question Source New Previous NRC Exam No Comments Operations Reviewer _ _I _ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 44 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 2 KJA 217000 2.4.2 Reactor Core Isolation Cooling Statement Emergency Procedures I Plan -Knowledge of system set points, interlocks and automatic actions associated with EOP entry conditions.

QUESTION 22 Which one of the following sets of alarms represents the mimimum requirement for entry into E0-1 00-1 04?

A. RCIC LEAK DETECTION HI TEMP/HI DIFF TEMP (AR-108-EOS), ONLY B. RCIC LEAK DETECTION LOGIC A HI TEMP (AR-108-F04)

OR RCIC LEAK DETECTION LOGIC 8 HI TEMP (AR-108-FOS)

C. RCIC LEAK DETECTION LOGIC A HI TEMP (AR-108-F04)

AND RCIC LEAK DETECTION LOGIC 8 HI TEMP (AR-108-FOS)

D. RCIC LEAK DETECTION HI TEMP/HI DIFF TEMP (AR-108-EOS)

AND RCIC LEAK DETECTION LOGIC A HI TEMP (AR-108-F04)

AND RCIC LEAK DETECTION LOGIC 8 HI TEMP (AR-108-FOS)

Proposed Answer A Applicant References None Explanation Entry into E0-000-104 is made on area temperatures, radiation levels or room flooding. The alarms listed for consideration all involve EO entry on room temperature. The E0-104 entry conditions (MAX NORMAL temperatures) are set to the setpoint of the first high temperature alarm for area with steam leak detection, such as the RCIC room. The MAX SAFE temperatures for these areas are set to the isolation setpoint. See E0-104 Table A Correct. This is the alarm received for elevated temperatures is the RCIC equipment room at 120 oF room temperature, 45 oF room t.T.

B Incorrect. These alarms are received when the respective channel of the isolation logic trips. These alarms are not required to be received for E0-104 entry as they do not alarm until the isolation setpoint at the MAX SAFE temperature is reached.

C Incorrect. These alarms are received when the respective channel of the isolation logic trips. These alarms are not required to be received for E0-104 entry as they do not alarm until the isolation setpoint at the MAX SAFE temperature is reached.

D Incorrect. The LOGIC A( B) alarms are received when the respective channel of the isolation logic trips. These alarms are not required to be received for E0-104 entry as they do not alarm until the isolation setpoint at the MAX SAFE temperature is reached.

10CFR55 41.7 Technical References E0-000-104 AR-1 (2)08-E05 Learning Objectives 14583 CONFIDENTIAL Examination Material Page 45 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Question Source New Previous NRC Exam No Comments Operations Reviewer _ _I _ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 46 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam I RO I Tier I2 I Group 11 I Cognitive Level I High I Level of Difficulty I 3 KJA 206000 K2.02 High Pressure Coolant Injection System jlmportance 1 2.8 Statement Knowledge of electrical power supplies to the following: System pumps: BWR-2,3,4 QUESTION 23 Unit 1 scrammed from rated power due to a loss of Feedwater.

Reactor level is being maintained +20" to +45" using RCIC.

Reactor pressure is being maintained 800-1050 psig with HPCI.

DC panel1 D274 is then de-energized.

Which one of the following describes the effect on HPCI , and any operator action required due to the loss of DC power?

A. HPCI will trip Maintain reactor pressure using SRVs B. HPCI will receive an isolation signal and trip, but fail to isolate Close HV-155-F002, STM SUPPLY IB ISO HV C. HPCI will remain in pressure control If HPCI trips on high reactor level, maintain reactor pressure using SRVs D. HPCI trip logic is defeated Isolate the HPCI steam supply on any HPCI trip signal Proposed Answer c Appl icant References None Explanation 1D274 is the 250V DC power supply to a number of components, including the HPCI Aux Oil Pump and various system valves.

A Incorrect. HPCI trip and control logic is power by 125V DC. None of the components affected by the loss of 250V DC power will result in a HPCI trip.

B Incorrect. The HPCI isolation logic is powered by 125V DC. None of the HPCI steam supply isolation valves are powered from 1D274.

C Correct. On a Level 8 signal the 125 VDC-powered HPCI trip logic will close the Turbine Steam Supply Valve F001, powered from 1 D264. As the HPCI turbine coasts down the loss of oil pressure from the shaft-driven main oil pump, with the AOP unavailable, will prevent re-opening the HPCI turbine stop valve if the trip condition clears.

D Incorrect. The HPCI trip logic is powered by 125V DC.

10CFR55 41.7 Technical References ON-188-001 TM-OP-052 CONFIDENTIAL Examination Material Page 47 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Learning Objectives 11257 b Question Source New Previous NRC Exam No Comments Operations Reviewer _ _I_ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 48 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam I RO I Tier I2 I Group 11 I Cognitive Level I High I Level of Difficulty 14 KIA 262001 K5.02 A.C. Electrical Distribution !Importance 1 2.6 Statement Knowledge of the operational implications of the following concepts as they apply to A. C. ELECTRICAL DISTRIBUTION: Breaker control QUESTION 24 The plant experienced a loss of offsite power.

Diesel Generator A started 1 minute ago, but did NOT load onto either ESS Bus 1A or 2A.

Conditions have deteriorated, such that the plant is now in a Station Blackout.

Which one of the following identifies the operation implications of immediately re-energizing ESS Buses 1A and 2A from the Control Room?

A. Entry into E0-1 00(200)-030, Unit 1(2) Response to Station Blackout, will NOT be required B. Diesel Generator A will trip due to loss of cooling after a few minutes C. Installation of Blue Max to 1D613 and 2D613 is no longer required D. Diesel Generator A will trip due to an overload condition because pump auto-start timers have timed out Proposed Answer B Applicant References None Explanation No ESW pumps are in service to provide cooling to Diesel Generator A. ESW Pump A has a pump start signal present. Due to the breaker configuration, the ESW Pump attempts to start onto a de-energize bus and trips with the start signal present. This actuates the anti-pump logic of the ESW Pump breaker. ESW Pump A will not automatically start when ESS Bus 1A is re-energized and cannot be started manually due to the anti-pump feature. Before the ESS Buses can be re-energized DG A must be shutdown locally, then breaker control power to ESW Pump A must be de-energized, then restored, to reset the anti-pump logic. When the Diesel Generator is restarted locally, the associated ESW pump will auto-start.

A Incorrect. Immediate entry into E0-100(200)-030 will not be required, but after DG A trips in 8 minutes due to a loss of cooling entry will be required.

B Correct. Runtime of a Diesel Generator loaded without cooling is approximately 4.5 minutes, unloaded 8 minutes.

C Incorrect. While the battery chargers will be momentarily restored when ESS Buses 1A and 2A are re-energized, the chargers will be lost once D G A trips due to loss of cooling.

D Incorrect. Pump autostart timers for other pumps will still function to prevent an overload trip of the Diesel Generator.

10CFR55 41.7 Technical References E0-1 00-030 Step 2.1 CONFIDENTIAL Examination Material Page 49 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Learning Objectives 14625 Question Source New Previous NRC Exam No Comments Operations Reviewer mj I 0612312014 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 50 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 4 KJA 261000 K1.01 Standby Gas Treatment System Statement Knowledge of the physical connections and/or cause-effect relationships between STANDBY GAS TREATMENT SYSTEM and the following: Reactor building ventilation system QUESTION 25 Unit 1 is operating at rated power when a small LOCA occurs .

Zone 1 and Zone 3 ventilation isolates.

RB RECIRC SYS TO SGTS DMP, HD-07543A, fails to automatically respond on the Zone 3 isolation signal.

Which one of the following specifies the pressure the Standby Gas Treatment system will establish in Zones 1 and 3?

A. more positive than 0" we B. O"wc C. more negative than -0.25" we D. more negative than -0.40" we Proposed Answer c Applicant References None Explanation The HD=07543A is 1 of 2 parallel dampers that provide a flowpath from the Reactor Building ventilation Recirc system to SGTS. Failure of just 1 damper still provides a suction source for SGTS to be able to drawdown Zones 1 and 3 to the design negative pressure of -0.25" we.

A Incorrect. This choice is consistent with the supply to SGTS isolated in conjunction with normal Zone 1 and 3 ventilation isolated, and the secondary containment slowly pressurizing.

B Incorrect. This choice is consistent with initial response of Zone 1 and 3 pressure to the supply to SGTS isolated in conjunction with normal Zone 1 and 3 ventilation isolated.

C Correct. The SGTS system will still be able to take a suction on Zones 1 and 3 and drawdown Zones 1 and 3 to the design pressure.

D Incorrect. This choice represents a failure of a SGTS modulating damper PPD-07554A to modulate to allow SGTS to limit drawdown to the design pressure of -0.25" we.

10CFR55 41.8 Technical References M-175 Sht 2 ON-159-002 Att B TM-OP-070 Learning Objectives 11228 f Question Source New Previous NRC Exam No CONFIDENTIAL Examination Material Page 51 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Comments Operations Reviewer mj I 0610312014 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 52 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 2 KIA 400000 K4.01 Component Cooling Water System Statement Knowledge of CCWS design feature(s) and or interlocks which provide for the following: Automatic start of standby pump QUESTION 26 Unit 1 is operating at rated power.

Annunciator RBCCW HEAD TANK HI-LO LEVEL (AR-123-E06) is received .

The NPO dispatched to the RBCCW head tank reports NO level in the tank sightglass. Makeup to the head tank is unsuccessful in recovering level.

The following annunciators are then received:

RBCCW PUMPS DISHARGE HEADER LO PRESS (AR-123-E03)

RBCCW HEAT EXCHANGER HEADER LO PRESS ( AR-123-E04)

Operators note Pl-11308, RBCCW HX DSH PRESS, is fluctuating widely.

Which one of the following identifies the action to be taken in response to this condition?

A. Depress and release the STOP pushbutton for each RBCCW Pump B. Depress the STOP pushbutton for the STANDY RBCCW Pump THEN Depress the STOP pushbutton for the running RBCCW Pump C. Depress AND hold the STOP pushbutton for both RBCCW Pumps THEN Release the STOP pushbuttons D. Depress AND hold the STOP pushbutton for both RBCCW Pumps Open the breakers for both RBCCW pumps Release the STOP pushbuttons Proposed Answer D Applicant References None Explanation RBCCW pumps automatically start on a low pump discharge pressure of 61 psig, as indicated by alarm AR-123-E03, regardless of pump status. In this question a leak has occurred somewhere in the RBCCW system as evidenced by the loss of level in the RBCCW head tank, with makeup to the head tank unable to restore level. The RBCCW pumps are cavitating due to the loss of system inventory as evidenced by the low-pressure alarms and the wide fluctuation in system pressure indicated. The action in response to pump cavitation per ON-114-001 Step 3.8.11 is to stop both RBCCW pumps.

A Incorrect. The pump auto-start logic will restart each pump as soon as the STOP PB is released .

CONFIDENTIAL Examination Material Page 53 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION B Incorrect. The pump auto-start logic does not differentiate between running and standby RBCCW pump. The pump auto-start logic will restart each pump as soon as the STOP PB is released.

C Incorrect. There is no interlock in the auto-start logic that looks at the status of both RBCCW pumps to bypass the auto-start on low system pressure.

D Correct. Both RBCCW pumps receive a start signal on low system pressure that is only bypassed by depressing the pump STOP PB. This is the means to shutdown the RBCCW system per 10CFR55 41.4 Technical References E-147 Sht 2 ON-114-001 OP-114-001 AR-123-E03 Learning Objectives 11086 a Question Source Bank ILO LXR TMOP014116941001 Previous NRC Exam No Comments Operations Reviewer _ _I _ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 54 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 3 KIA 215002 K1.05 Rod Block Monitor System Statement Knowledge of the physical connections and/or cause/effect relationships between ROD BLOCK MONITOR SYSTEM and the following: Four rod display: BWR-3,4,5 QUESTION 27 The Rod Block Monitor Operator Display Assemblies located above the 4-Rod Display, on the Standby Information Panel, experience a loss of power.

Which one of the following identifies the effect of the loss of the ODAs on the RBM and the APRMs?

A. No control rod withdrawal blocks No RPS actuation B. Control rod withdrawal block due to RDCS inoperable No RPS actuation C. Control rod withdrawal block due to RBM inoperable No RPS actuation D. Control rod withdrawal block due to APRM inoperable Full RPS actuation Proposed Answer A Applicant References None Explanation The RBM ODAs comprise part of the OEM 4-rod display. The RBM ODAs provide LPRM indication for the 4 LPRM strings surrounding the selected control rod.

The ODAs are not required for RBM or APRM operability. The ODAs are powered from non-Class 1E 120 V Instrument AC 1Y218-014.

A Correct. Loss of the ODAs has no effect on RBM or APRM operability. No control rod block or scram signals are generated.

B Incorrect. The components powered by 1Y218 on the SIP are not required for RDCS operability. The 4-rod display is powered from 1Y219.

C Incorrect. The operability of the RBM is unaffected by the loss of the ODA.

D Incorrect. The operability of both the RBM and APRMs are unaffected by the loss of their ODAs. Any control rod block will not be due to APRM inoperable.

10CFR55 41.6 Technical References ON-117 -001 Att A TM-OP-078K Learning Objectives 15804 Question Source New Previous NRC Exam No Comments CONFIDENTIAL Examination Material Page 55 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Operations Reviewer _ _I _ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 56 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 2 KIA 201001 K2.01 Control Rod Drive Hydraulic System Statement Knowledge of electrical power supplies to the following: Pumps QUESTION 28 Unit 2 is operating at rated power.

CRD Pump 2B is out of service following routine maintenance.

Offsite power is lost from the Mountour/Mountain switchyard.

RPS buses remain energized during the transient.

Which one of the following describes the action required on Unit 2 to maintain power operation?

A. Cross-tie Instrument Air to Containment Instrument Gas per ON-225-001, Loss of CIG B. Restart CRD Pump 2A per ON-255-007, Loss of CRD System Flow C. Restore Drywell Cooling isolation per ON-003-001, Loss of Startup Bus 10 D. Restore Recirc Pump cooling per ON-003-002, Loss of Startup Bus 20 Proposed Answer B Applicant References None Explanation On Unit 2, CRD Pump 2A is in service. It is powered from ESS Bus 2A, whose normal feed is from Startup Bus 10. When power is lost to the 230 KV grid, ESS Bus 2A will transfer to the alternate supply from Startup Bus 20. The fast transfer results in a momentary de-energization of ESS Bus 2A and a trip of CRD Pump 2A. Failure to restore CRD will eventually require a reactor scram due to the loss of charging water pressure, as HCU accumulators experience a slow loss of pressure.

A Incorrect. With RPS power maintained a CIG isolation does not occur and cross-tying 1/A to CIG is not required.

B Correct. CRD Pump 2A loses power on the fast transfer of ESS Bus 2A to the alternate source. This is a subsequent action for a loss of SUB10.

C Incorrect. A Drywell Cooling isolation does not occur on a loss of ESS Bus power, as the DW cooling isolation logic is initiated from low-pressure ECCS initiation logic. The DW cooling isolation solenoids are powered from 1Y219 UPS power.

D Incorrect. While Recirc Pump cooling is required to be restored following a momentary loss of power to ESS Bus 2A, this is the incorrect procedure. The 230 KV offsite grid supplies SUB 10, not SUB 20.

10CFR55 41.4 Technical References ON-003-001, ON-204-201 Learning Objectives 10018 a Question Source New CONFIDENTIAL Examination Material Page 57 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Previous NRC Exam No Comments Operations Reviewer _ _I _ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 58 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam I RO I Tier I 2 I Group I 2 I Cognitive Level I High I Level of Difficulty 14 KIA 239001 K3.15 Main and Reheat Steam System I Importance 1 3.5 Statement Knowledge of the effect that a loss or malfunction of the MAIN AND REHEAT STEAM SYSTEM will have on following: Reactor water level control QUESTION 29 Unit 1 is operating a 65 percent power.

Inboard MSIV HV-141-F022A fails closed.

The unit remains on-line.

Which one of the following describes how Feedwater level control responds to the MSIV closure?

A. Feedwater level control transfers to 1E-CONTROL Reactor level lowers slightly due to the MSIV closure, then stabilizes at +35" B. MSL A flow is substituted as approximately 3.5 Mlbm/hr Total Steam Flow remains selected for input to 3E-CONTROL Reactor level rises due to the rise in Total Steam Flow, then stabilizes at +35" C. MSL A flow is substituted as 0 Mlbm/hr Total Steam Flow remains selected for input to 3E-CONTROL Reactor level drops due to the drop in Total Steam Flow, then stabilizes at +35" D. MSL A flow is substituted as approximately 0 Mlbm/hr Turbine 1st Stage Pressure/Flow selected for input to 3E-CONTROL Reactor level lowers slightly due to the MSIV closure, then stabilizes at +35" Proposed Answer D Applicant References None Explanation The plant will remain on-line for a single MSL isolated at reduced power. Steam flow in the isolated line falls to 0 Mlbm/hr. ICS compares each steam line flow to the high median steam flow, in this case the middle value of the 3 steam line flow for the unisolated lines or approximately 3.5 Mlbm/hr. MSL A flow will be substituted, as it exceeds the +/-0. 75 Mlbm/hr deviation criteria. The average of the remaining 3 MSL flows is used as the substitute value.

The total steam flow is then recalculated with the substitute value for MSL A and compared to Turbine 1st stage pressure. Use of the average value through 3 MSL flows will result in a total MSL flow well above the actual MSL flow, as total MSL flow is high by 1/3 due to using a substitute value for MSL A instead of the actual value of 0. Total steam flow will fail the validation test of +/-2.1 Mlbm/hr difference when compared to Turbine 1st stage pressure/flow.

Turbine 1st stage pressure/flow is then used as the input to 3E-CONTROL, and the substitute value for MSL A flow is set to 0 Mlbm/hr.

Reactor level drops slightly on the MSIV closure due to the momentary pressure spike and void collapse. FWLC in 3-E will quickly stabilize level at the setpoint.

CONFIDENTIAL Examination Material Page 59 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION A Incorrect. FWLC doesn't swap to 1E control until both the total MSL flow (due to 2 MSL flow inputs bad or unusable) and turbine 1st stage pressure/flow inputs are both unusable. The response of reactor level is what is expected for a transfer to 1E control simultaneous with a MSL isolation.

B Incorrect. This represents a failure to recognize the validation of the total MSL flow will fail due to being one-third higher than actual MSL flow due to the substitution effect.

ICS FWLC is steam-flow dominant, so a sudden rise in steam flow will result in a corresponding rise in FW flow. Level will rise by a few inches, then return to the setpoint as the level deviation integrates in the Master Level Controller.

C Incorrect. The substitute value for MSL A flow is approximately 3 Mlbm/hr. Total steam flow would not drop and induce a level transient due to 3E control action.

D Correct. MSL A flow is substituted as described, Turbine 1st stage pressure is selected due to the Total Steam Flow value being approximately 1/3 higher than actual steam flow, and the only level transient is due to the MSIV closure.

10CFR55 41.5 Technical References ON-145-001 Section 2.2, Att B Learning Objectives 16087 Question Source Bank LXR LOR TMOP0451/16001/002 Previous NRC Exam No Comments Operations Reviewer mj I 06/03/2014 Facility Representative _ _/_ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 60 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam I RO I Tier I 2 I Group I 2 I Cognitive Level I Low I Level of Difficulty I 2 KIA 286000 K4.03 Fire Protection System !Importance 13.3 Statement Knowledge of FIRE PROTECTION SYSTEM design feature(s) and/or interlocks which provide for the following: Maintenance of fire header pressure QUESTION 30 The Fire Protection System is in the normal lineup.

An electrical fire causes the loss of the Motor-Driven Fire Pump.

Which one of the following describes the response of the Fire Protection System to maintain fire header pressure?

A. Backup Motor-Driven Fire Pump will start at 95 psig B. Diesel Engine-Driven Fire Pump will start at 95 psig C. Diesel Engine-Driven Fire Pump will start at 85 psig D. Backup Diesel Engine-Driven Fire Pump will start at 85 psig Proposed Answer c Applicant References None Explanation A fire has occurred and the Motor-Driven Fire Pump has failed. Only the Diesel Engine Driven Fire Pump is available to maintain fire header pressure. Backup Fire Protection is normally isolated from the main Fire Protection header and is unavailable.

A Incorrect. This is the starting setpoint of the Motor-Driven Fire Pump, but while the Backup Fire Protection system contains exact duplicates of the Jockey Fire Pump and the Diesel Engine-Driven Fire Pump, there is no Backup Motor-Driven Fire Pump.

B Incorrect. This is the starting setpoint of the MDFP, not the DDFP.

C Correct. This is the only standby fire pump aligned to the Fire Protection header. The DDFP auto-starts at 85 psig.

D Incorrect. Both DDFP (normal and Backup) auto-start at 85 psig, however Backup Fire Protection is not normally aligned for service.

10CFR55 41 .4 Technical References OP-013-001 Learning Objectives 11385 c Question Source Bank ILO LXR TMOP013/2291/003 Previous NRC Exam No Comments Operations Reviewer mj I 06/24/2013 Facility Representative _ _/_ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 61 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION BLANK PAGE CONFIDENTIAL Examination Material Page 62 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam I RO I Tier I 2 I Group I 2 I Cognitive Level I High I Level of Difficulty 14 KJA 201003 K5.05 Control Rod and Drive Mechanism I Importance 1 3.0 Statement Knowledge of the operational implications of the following concepts as they apply to CONTROL ROD AND DRIVE MECHANISM : Reverse power effect QUESTION 31 Unit 1 is starting up. Reactor power is approximately 45 percent.

Operators are withdrawing 12 shallow control rods, from position 40 to position 48, per Reactor Engineering direction.

Which one of the following identifies the operational concern associated with these control rod withdrawals?

A. Violation of the MCPR limit due to excessive bottom-peaked power shape B. Violation of the MCPR limit due to excessive top-peaked power shape C. Reduction in reactor power due to change in core void distribution D. Increased RBM rod out blocks due to the effect on A-level LPRMs Proposed Answer c Applicant References None Explanation Withdrawal of shallow control rods will result in a change in core void distribution. Insertion of shallow control rods results in reduced void fractions in the 4 bundles in the control cell, resulting in higher bundle power. When the shallow control rods are withdraw void fractions rise in the now-uncontrolled bundles and total core power lowers.

A Incorrect. MCPR limit violations are typically not of concern at low power/low rod-line conditions. MCPR is more limiting for top-peaked power shape.

B Incorrect. While the MCPR limit is more affected by top-peaked power shapes, this control rod pattern adjustment will result in a much more strongly bottom-peaked power shape, not top-peaked.

C Correct. This is an operational concern, anticipating the effect on core power of shallow control rod withdrawal.

D Incorrect. While A-level LPRMs are most strongly affected by the control rod withdrawal, the A-level LPRMs are not used in the RBM.

10CFR55 41.5 Technical References SC056A Chapter 5 Learning Objectives SC056A Ch 5 Obj 12 Question Source New Previous NRC Exam No Comments CONFIDENTIAL Examination Material Page 63 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Operations Reviewer _ _I _ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 64 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 2 KIA 204000 K6.05 Reactor Water Cleanup System Statement Knowledge of the effect that a loss or malfunction of the following will have on the REACTOR WATER CLEANUP SYSTEM : A. C. power QUESTION 32 Unit 2 startup is in progress, in Mode 2 at 50 psig.

CRD Pump 2B is in-service.

Power to Startup Bus 10 is lost.

ESS Bus 2A fails to transfer to its alternate supply, but is re-energized by Diesel Generator A.

Which of the following describes the effect of the power loss on Unit 2 reactor level?

A. Reactor level is rising due to the loss of Main Turbine EHC B. Reactor level is rising due to the loss of RWCU blowdown C. Reactor level is falling due to the loss of CRD D. Reactor level is falling due to the loss of Condensate Proposed Answer B Applicant References None Explanation On Unit 2 a loss of SUB10 will result in a momentary loss of ESS Buses 2A and 2C and a loss of RPS 2A. Unit 2 Aux Buses are unaffected as they are supplied from SUB20. The loss of RPS will result in a loss of RWCU due to a partial isolation by the PCIS outboard logic.

A Incorrect. Unit 2 Aux Buses are powered from SUB20. This would be the effect on Unit 1 as main turbine shell warming would isolate on the loss of EHC.

B Correct. RWCU pumps would trip and RWCU would be isolated from the reactor due to the RPS 2A trip on the ESS Bus 2A transfer to alternate.

C Incorrect. CRD Pump 2B is powered from ESS Bus 20 and is unaffected by the transient.

D Incorrect. Condensate would be running per G0-200-002, with 1 pump in service, before the loss of SUB 10. The in-service Condensate would continue to operate. CRD is adequate to maintain reactor level at the power level typical for this reactor pressure, so a loss of Condensate will not affect reactor level.

10CFR55 41.5 Technical References ON-003-001 ON-258-001 Learning Objectives 11085 g Question Source New Previous NRC Exam No CONFIDENTIAL Examination Material Page 65 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Comments Operations Reviewer mj I 06124114 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 66 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam I RO I Tier I2 I Group I 2 JCognitive Level I High I Level of Difficulty I 2 KJA 230000 A1.01 RHRILPCI: Torus/Suppression Pool Spray I Importance 13.8 Mode Statement Ability to predict and/or monitor changes in parameters associated with operating the RHRILPCI:

TORUS/SUPPRESSION POOL SPRAY MODE controls including: Suppression chamber pressure QUESTION 33 Unit 1 scrammed from rated power on a turbine trip.

After the scram, primary containment pressure begins to rise. Primary containment pressures are as follows :

Drywell pressure 1.9 psig, steady Suppression Chamber pressure 2.3 psig, up slow E0-100-103 is entered for high Drywell pressure.

RHR Loop A is placed in Suppression Chamber spray per OP-149-004, RHR Containment Cooling.

HV-151-F027A, SUPP POOL SPRAY CTL, is opened fully when FI-15120A, CONTN SPRAY DIV 1, fails to respond.

FI-E11-1 R603A, RHR A/C FLOW, indicates approximately 550 gpm .

Which one of the following describes the expected response of primary containment pressure in these conditions?

A. Drywell pressure remains steady Suppression Chamber pressure lowers B. Drywell pressure remains steady Suppression Chamber continues to rise C. Drywell pressure begins to lower Suppression Chamber pressure remains steady D. Drywell and Suppression Chamber pressure continue to rise Proposed Answer A Applicant References None Explanation The conditions in the stem are consistent with a leaking SRV with a tailpipe rupture in the Suppression Chamber as indicated by Suppression Chamber pressure greater than Drywell Pressure. Drywell pressure is rising intermittently as the DW-SC vacuum breakers cycle at 0.5 psid. RHR Loop A system flow is indicated as 550 gpm, the approximate value for full flow with a full open spray valve. Action to fully open the spray valve on a failed SC spray indicator is from OP-149-004.

CONFIDENTIAL Examination Material Page 67 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION A Correct. The SC spray flow will immediately begin to lower SC pressure due to condensation of steam in the SC airspace from the leaking SRV. OW pressure will remain steady due to the loss of OW cooling and SC no longer relieving steam back to the OW through the DW-SC vacuum breakers.

B Incorrect. If SC pressure continues to rise, OW pressure will rise when the differential between the two compartments exceeds 0.5 psid and the vacuum breakers relieve the SC to the DW.

C Incorrect. The RHR system flow indication is indicative of SC spray flow. SC pressure is expected to lower when spraying a SC filled with steam from a leaking SRV tailpipe before OW pressure would lower.

D Incorrect. SC pressure would be expected to fall due to the indication of SC spray flow.

OW pressure would not rise any higher once the rise in SC pressure is arrested.

10CFR55 41.5 Technical References OP-149-004 Section 2.8.2 E0-000-1 03 Step PCIP-4 Learning Objectives 10771 s Question Source New Previous NRC Exam No Comments Operations Reviewer _ _I _ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 68 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 4 KIA 226001 A2.06 RHRILPCI: Containment Spray System Mode Statement Ability to (a) predict the impacts of the following on the RHRILPCI: CONTAINMENT SPRAY SYSTEM MODE ; and (b) based on those predictions, use procedures to correct, control, or mitigate the consequences of those abnormal conditions or operations: D.C. electrical failures QUESTION 34 Unit 1 is operating at rated power with RHR Loop B out of service for a SOW.

The reactor scrams due to a small LOCA in the Drywell.

E0-1 00-103 is entered for high Drywell pressure.

RHR Loop A is placed in Suppression Chamber spray per OP-149-004, RHR Containment Cooling .

Before containment pressure reaches the threshold for Drywell spray, annunciator RHR LOOP A OUT OF SERVICE (AR-1 09-B09) alarms.

The following conditions are observed:

BIS LOOP A RELAY LGC PWR FAILURE (AR-154-A02) LIT RHR LOOP A INIT ISO RESET (HS-E11-1 S56A) Extinguished LOCA ISOLATION MANUAL OVERRIDE (HS-E11-1S17A) Extinguished Which one of the following identifies the preferred method to place Drywell spray in service?

Note: HV-151-F021A- DRYWELL SPRAY IB ISO valve HV-151-F016A- DRYWELL SPRAY OB ISO valve A. Open the outboard HV-151-F016A valve from the Control Room Open the inboard HV-151-F021A valve locally B. Open the inboard HV-151-F021A valve from the Control Room Open the outboard HV-151-F016A valve locally C. Open both RHR Loop A Drywell spray valves locally D. Open both RHR Loop A Drywell spray valves from the Control Room Proposed Answer D Applicant References None Explanation A LOCA has occurred. Only RHR Loop A is available. A loss of RHR logic power occurs before DW sprays can be aligned. The loss of logic power results in losing the manual containment cooling override feature in the RHR logic, but it also defeats the automatic close signal to the OW spray valves from the LOCA signal. There is no interlock between the 18 and 08 OW spray valves, so both valves can be opened from the Control Room.

CONFIDENTIAL Examination Material Page 69 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION A Incorrect. Local valve operations are not required.

B Incorrect. Local valve operations are not required.

C Incorrect. Local valve operations are not required.

D Correct. The valves can be opened from the Control Room.

10CFR55 41.7 Technical References AR-154-A02 E-153 Sht 95 M1-E11-66 Sht4, 5 Learning Objectives 10768 b Question Source New Previous NRC Exam No Comments Operations Reviewer mj I 0610312014 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 70 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 3 KIA 271000 A3.01 Offgas System Statement Ability to monitor automatic operations of the OFF GAS SYSTEM including: Automatic system isolations QUESTION 35 Unit 1 is operating at rated power.

The following alarms are received UNIT 1 RECOMBINER CCW PUMP DISCHARGE PRESSURE LO (AR-131-A02)

UNIT 1 RECOMBINER CCW PUMP MOTOR TROUBLE (AR-131-A03)

The alarms cannot be cleared.

Which one of the following identifies the effect of the alarms and the action that can be taken in response?

A. Offgas isolation Swap Unit 1 to the Common Recombiner B. Offgas isolation Place the Common GRRCCW Pump in service C. ARESD Signal (HV-10721, SJAE DSCH ISO closed)

Re-open SJAE suction valves D. Recombiner shutdown Reset the Recombiner Shutdown and return the Recombiner to service Proposed Answer A Applicant References None Explanation The alarms received will result in an Offgas isolation on low Recombiner condenser cooling water flow due to trip of the Unit 1 GRCCW pump. As the alarms cannot be cleared the Unit 1 Recombiner cannot be returned to service.

A Correct. An Offgas isolation will occur on the pump trip, resulting in closure of the SJAE suction valves. The Common Recombiner must be placed in-service to Unit 1 to restore Offgas.

B Incorrect. While an Offgas isolation will occur, the Common GRCCW Pump cannot be aligned to the Unit 1 Recombiner.

C Incorrect. Closure of the HV-1 0721 generates an ARESD signal, it does not result from another initiating condition. The SJAE suction valves cannot be reopened until the Common Recombiner is placed in service.

D Incorrect. The Recombiner shutdown signal likely would not be received due to the loss of flow in the GRCCW loop. The Uni1 Recombiner shutdown signal will not reset and stay reset until the Unit 1 GRCCW Pump can be restarted.

10CFR55 41.7 CONFIDENTIAL Examination Material Page 71 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Technical References AR-131-A02, A03 ON-143-001 Learning Objectives 10930 b Question Source Bank LXR LOR AD0451153041086 Previous NRC Exam No Comments Operations Reviewer mj I 05114114 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 72 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 2 KIA 241000 A4.07 Reactor/Turbine Pressure Regulating System Statement Ability to manually operate and/or monitor in the control room: Main stop/throttle valves (operation)

QUESTION 36 When conducting the quarterly surveillance of Turbine Stop Valves (MSV-1 ,2,3,4) per S0-193-001, Quarterly Turbine Valve Cycling, which one of the following signals will energize the fast-acting solenoid?

A. First 10 percent of valve stroke B. First 10 seconds of valve stroke C. Last 10 percent of valve stroke D. Stop Valve Test Switch opens Proposed Answer c Applicant References None Explanation Per S0-193-001 Step 5.2.5e, the TSV will fast-close once the valve reaches the 90 percent closed position.

A Incorrect. The valve will fast-close over the last 10 percent of valve position 8 Incorrect. The fast-close signal is based on valve position, not stroke time.

C Correct. The valve fast-closes for the last 10 percent of valve stroke.

D Incorrect. The valve fast-closes when the Stop Valve Test Switch closes.

10CFR55 41 .7 Technical References S0-193-001 Learning Objectives 1658 h Question Source Bank ILO LXR TMOP093E/1658/001 Previous NRC Exam No Comments Operations Reviewer _ _/_ __ Facility Representative _ _/_ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 73 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION BLANK PAGE CONFIDENTIAL Examination Material Page 74 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 2 KJA 201006 2.2.42 Rod Worth Minimizer System (RWM)

Statement Ability to recognize system parameters that are entry-level conditions for Technical Specifications.

QUESTION 37 Which one of the following requires entry into a Technical Specification LCO?

A. 1 channel of EOC-RPT inoperable at 25 percent power, MCPR limits for inoperable EOC-RPT not applied B. Extraction steam isolated to 1 of the 2 in-service Feedwater heater strings at 20 percent power C. Rod Block Monitor A bypassed during startup at 15 percent power D. Rod Worth Minimizer bypassed for plant shutdown at 10 percent power Proposed Answer D Applicant References None Explanation The question presents four conditions for evaluation for LCO entry.

A Incorrect. EOC-RPT operability is not required until 26 percent power per TS 3.3.4.1.

B Incorrect. While ON-147-002 requires entry into LCO 3.2.2 with extraction steam isolated to 1 heater string with only 2 heaters in-service, at 20 percent power MCPR limits do not apply per TS 3.2.2.

C Incorrect. RBM operability is not required until 28 percent power per TS 3.3.2.1.

D Correct. The RWM bypassed at 10 percent power does not comply with LCO 3.3.2.1.

10CFR55 41.6 Technical References TS 3.3.2.1 Learning Objectives 13426 Question Source New Previous NRC Exam No Comments Operations Reviewer _ _I _ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 75 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION BLANK PAGE CONFIDENTIAL Examination Material Page 76 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 3 KJA 290002 2.2.40 Reactor Vessel Internals Statement Ability to apply Technical Specifications for a system.

QUESTION 38 Use your provided references to answer this question.

Unit 1 is preparing to restart Recirc Pump A at power.

Current conditions are as follows:

Reactor power 30 percent Load-line 58 percent Steam dome temperature 539 °F Bottom head drain temperature 509 °F Recirc Pump A loop temperature 479 °F Recirc Pump B loop temperature 514 °F Recirc Pump B loop flow 18,000 gpm Which one of the following identifies the action required to proceed with the pump start?

A Raise Recirc Pump B loop flow~ 21,320 gpm B. Insert control rods to lower reactor powers 27 percent C. Raise Recirc Pump A loop temperature ~ 489 oF D. Maintain Recirc Pump A loop temperature ~ 464 oF Proposed Answer D Applicant References TS 3.4.10 Explanation An application of TS 3.4.10 is required to determine the action required to allow start of an idle Recirc Pump at power. SR 3.4.10.3 and SR 3.4.10.4 specify the limits to apply to satisfy LCO 3.4.10.

A Incorrect. This represents a mis-application of the note to SR 3.4.10.6 for power increases in SLO. Operation in SLO would be allowed with loops flows> 21,320 gpm.

Start of an idle loop is not allowed by OP-164-001 with flows above 19,500 gpm to protect the TRS limit of 50 percent loop flow (21,320 gpm).

B Incorrect. This represents a mis-application of the note to SR 3.4.10.6 for power increases in SLO.

C Incorrect. This is the action required if the idle loop temperature must be within 50 oF of steam dome temperature. The bases for SR3.4.1 0.4 allow the use of running loop temperature to be used as the coolant temperature for the SR.

D Correct. The bases for SR 3.4.10.4 allow the use of running loop temperature to be used as the coolant temperature for the SR. This use is reflected in OP-164-002 Step 2.4.27.d(3). This is the lowest temperature allowed in the idle loop to be within 50 oF of the running loop temperature.

CONFIDENTIAL Examination Material Page 77 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION 10CFR55 41.10 Technical References TS 3.4.10 OP-164-001 Step 2.4.27.d(3)

Learning Objectives 13225 Question Source New Previous NRC Exam No Comments Operations Reviewer _ _I _ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 78 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 2 KJA 295028 EK1.01 High Drywell Temperature Statement Knowledge of the operational implications of the following concepts as they apply to HIGH DRYWELL TEMPERATURE : Reactor water level measurement QUESTION 39 Unit 1 is operating at rated power when a small steam leak occurs in the Drywell.

Operators note the Wide Range level indications on 1C601 recorders UR-14201A(B), RPV PARAMETERS PAM RECORDER.

Which one of the following identifies the operational implications of a steam leak in the vicinity of the condensing chamber for the Wide Range A level indication?

A. Wide Range A will indicate lower than Wide Range B B. Wide Range A will indicate higher than Wide Range B C. Wide Range A will gradually fail downscale D. Wide Range A will gradually fail upscale Proposed Answer B Applicant References None Explanation Elevated temperatures in the area of a level instrument reference leg will result in erroneously high indicated level due to the higher temperature, lower density fluid in the reference leg.

With a steam leak in the area of the D004A reference leg, all Wide Range A level indications will indicate higher than Wide Range B.

A Incorrect. WR A will indicate higher than WR B.

B Correct. WR A will indicate higher than WR B. WR B should be selected for reactor level control.

C Incorrect. WR A would not fail downscale, it would indicate higher.

D Incorrect. WR A would not fail upscale, the instrument is designed to provide accurate reactor level indication during the DBA LOCA.

10CFR55 41.5 Technical References ON-145-004 TM-OP-080 Learning Objectives 1479 i Question Source New Previous NRC Exam No Comments Operations Reviewer _ _/_ __ Facility Representative tnc I 0612912014 lnit I date lnit I date CONFIDENTIAL Examination Material Page 79 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION BLANK PAGE CONFIDENTIAL Examination Material Page 80 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 2 KIA 700000 AK1.01 Generator Voltage and Electric Grid Disturbances Statement Knowledge of the operational implications of the following concepts as they apply to GENERATOR VOLTAGE AND ELECTRIC GRID DISTURBANCES: Definition ofterms: volts, watts, amps, VARs, power factor QUESTION 40 Both units are operating at rated power with 1 Reactor Recirc Pump in MONITOR mode.

A grid transient occurs.

Margins to the Main Generator Capability Curve are as shown:

Unit 1 -4 MW, down slow Unit 2 +2 MW, down slow TCC contacts the Control Room and requests that both units assume a more lagging power factor.

Which one of the following identifies the action to take on both units to satisfy the TCC request while maintaining margin to the Main Generator Capability Curve?

A. Place Reactor Recirc in MANUAL Lower Auto Voltage Regulator to operate as close as possible to 0 VARs B. Ensure Reactor Recirc lowers power Raise Auto Voltage Regulator as allowed by the capability curve C. Place Reactor Recirc in MANUAL Raise Auto Voltage Regulator as allowed by the capability curve D. Ensure Reactor Recirc lowers power Lower Auto Voltage Regulator to operate as close as possible to 0 VARs Proposed Answer B Applicant References None Explanation Unit 1 is operating above the main generator capability curve, with Unit 2 approaching the curve, due to a grid transient that resulted in both units assuming more reactive load. Action must be taken on Unit 1 to restore operation within the capability curve. TCC has requested both units assume a more lagging power factor. This requires both units to assume more reactive loading and raise vars. The MONITOR mode of recirc will initiate core power reductions to lower MWe loading to restore margin to the capability curve.

A Incorrect. Placing recirc in manual will result in MWe remaining constant. Combined with lowering VARs this will result in operating with a more leading power factor.

B Correct. Lowering MWe will restore margin to the capability curve allowing the units to assume more VAR loading, resulting in a more lagging power factor CONFIDENTIAL Examination Material Page 81 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION C Incorrect. With MWe constant due to the action to maintain core power constant, the only adjustment possible to the Auto Voltage regulator is to lower VAR loading to restore margin to the capability curve. Lowering VARs results in a more leading power factor.

0 Incorrect. Lowering VARs will result in a more leading power factor.

10CFR55 41 .5 Technical References ON-198-001 TM-OP-0980 Learning Objectives 10850 a Question Source New Previous NRC Exam No Comments Operations Reviewer _ _I _ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 82 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 3 KIA 295021 AK1.04 Loss of Shutdown Cooling Statement Knowledge of the operational implications of the following concepts as they apply to LOSS OF SHUTDOWN COOLING : Natural circulation QUESTION 41 Unit 1 is shutting down for a refueling outage in Mode 4, reactor coolant temperature 195 oF.

RHR is operating in Shutdown Cooling .

Recirc Pumps are shutdown.

Reactor head vents to the Drywell sump have NOT been opened.

A leak results in reactor level lowering to +5" .

Which one of the following identifies (1) the correct indication for determining vessel heatup rate?

(2) how entry into Mode 3 would be indicated?

A RWCU bottom head drain temperature (NLT01 or TR-821-1 R006)

Mode 3 entry is indicated by RWCU drain temperature B. Reactor vessel skin temperature (TE-821-1 N030E)

Mode 3 entry is indicated by reactor vessel skin temperature C. Reactor vessel skin temperature (TE-821-1 N030E)

Mode 3 entry must be inferred from steam dome pressure rise D. RHR heat exchanger inlet temperature (TRS-E11-1 R601)

Mode 3 entry must be inferred from steam dome pressure rise Proposed Answer c Applicant References None Explanation With reactor level falling to +5" a RHR SOC isolation occurs. RHR pumps trip on loss of suction path as the RHR F008 and F009 valves close. No recirc pumps are running and level is

< 45" so no core coolant circulation is occurring. ON-149-001 specifies the methods for determining vessel heatup. With the reactor head vents not yet aligned to the Drywell sump the reactor will pressurize as coolant temperature rises and reaches saturation in the core.

A Incorrect. Use of RWCU for coolant temperature is not allowed by ON-149-001 Step 3.4.6.b as no core circulation is occurring. RWCU drain temperature is not indicative of core coolant temperature.

B Incorrect. Although ON-149-001 does allow the use of vessel skin temperature under these conditions, this temperature is not reflective of core coolant temperature because of the lack of circulation in the reactor due to the low reactor level and no recirc pumps running.

CONFIDENTIAL Examination Material Page 83 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION C Correct. ON-149-001 does allow the use of vessel skin temperature under these conditions. Entry into Mode 3 will be indicated when reactor pressure begins to rise as core coolant temperature reaches saturation and starts to steam.

D Incorrect. ON-149-001 does allow the use of vessel skin temperature under these conditions.

10CFR55 41.5 Technical References ON-149-001 Step 3.5, 5.0 Learning Objectives 10771 r Question Source Bank LOR LXR TMOP0491107711001 Previous NRC Exam No Comments Operations Reviewer mj I 0612412014 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 84 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 2 KIA 600000 AK2.01 Plant Fire On Site Statement Knowledge of the interrelations between PLANT FIRE ON SITE and the following : Sensors I detectors and valves QUESTION 42 The Control Structure HVAC rooms in Area 12/21-783 are protected by a Pre-Action Sprinkler system.

Which one of the following identifies the condition(s) required to be met to discharge fire suppression water into the area in the event of a fire?

A. Simplex Priority 1 alarm must be received for the area, ONLY B. Simplex Priority 2 alarm must be received for the area, ONLY C. Area temperatures must exceed the melt temperature of the sprinkler head fusible links AND Simplex Priority 2 alarm must be received for the area D. Area temperatures must exceed the melt temperature of the sprinkler head fusible links AND OS& Y valve must be opened locally AND Sprinkler system isolation valve must be opened locally Proposed Answer c Applicant References None Explanation Pre-action Sprinkler systems require 2 conditions be satisfied to discharge fire suppression water into an area. First the sprinkler piping must be charged by opening the pre-action valve.

This occurs when the Simplex Priority 1 alarm is received. Second area temperatures must rise sufficiently to melt the fusible links in the closed sprinkler heads in the area. Only when both conditions are satisfied will fire suppression water be discharged into the area.

A Incorrect. This is indicative of opening of the pre-action valve to charge the sprinkler header. No fire suppression water is discharged into the area until the sprinkler fusible heads melt. This distractor is a description of how a pre-action deluge system functions.

8 Incorrect. This is indicative of fire detection in the area. No action is initiated by the fire suppression system on the detection alarm.

C Correct. This is indicative of opening of the pre-action valve to charge the sprinkler header. No fire suppression water is discharged into the area until the sprinkler fusible heads melt.

D Incorrect. The local valve operations are required for a manual deluge system.

10CFR55 41.4 CONFIDENTIAL Examination Material Page 85 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Technical References FP-013-186 OP-013-001 Step 2.5.3.a Note AR-SP-002 AR-SP-001 TM-OP-013, TM-OP-013Z Learning Objectives 11383 h Question Source New Previous NRC Exam No Comments Operations Reviewer mj I 0610312014 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 86 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 2 KIA 295005 AK2.02 Main Turbine Generator Trip Statement Knowledge of the interrelations between MAIN TURBINE GENERATOR TRIP and the following:

Feedwater temperature QUESTION 43 Which one of the following identifies why reactor power rises by approximately 4 percent when the Main Turbine is tripped during a normal plant shutdown per G0-1 (2)00-004, Plant Shutdown to Minimum Power?

A. Reactor pressure rises to a new steady-state value when pressure control is transferred to the bypass valves B. Extraction steam is isolated to the #1 and #2 Feedwater heaters, ONLY, when the Main Turbine is tripped C. Extraction steam is isolated to the #3 , #4 and #5 Feedwater heaters, ONLY, when the Main Turbine is tripped D. Extraction steam is isolated to ill! Feedwater heaters when the Main Turbine is tripped Proposed Answer D Applicant References None Explanation A turbine trip results in isolation of extraction steam to all Feedwater heaters. #5 heater is 9th stage extraction from the HP turbine, all others are extraction steam from the LP turbines. A turbine trip isolates extraction steam to all FW heaters. In G0-1 (2)00-004 Step 5.28 Note states reactor power rises approximately 4 percent on the turbine trip.

A Incorrect. Reactor pressure does rise slightly after the trip of the main turbine, approximately 3 psig. This variation in reactor pressure is small and insufficient to cause power to rise by 4 percent.

B Incorrect. Extraction steam is isolated to all FW heaters. This distractor is plausible as the #1 and #2 heaters do not have MOV isolation valves in their extraction steam supply.

C Incorrect. Extraction steam is isolated to all FW heaters. This distractor is plausible as the #3, #4 and #5 heaters all have MOV isolation valves in their extraction steam supply.

D Correct. All extraction steam is isolated to all FW heaters on a turbine trip.

10CFR55 41.5 Technical References G0-1 00-004 Step 5.28 Note M-102-1 Learning Objectives 11172 Question Source New Previous NRC Exam No Comments Operations Reviewer _ _I _ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 87 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION BLANK PAGE CONFIDENTIAL Examination Material Page 88 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam I RO I Tier 11 I Group 11 I Cognitive Level I Low I Level of Difficulty I 2 KIA 295031 EK2.15 Reactor Low Water Level I Importance 1 3.2 Statement Knowledge of the interrelations between REACTOR LOW WATER LEVEL and the following: A. C.

distribution QUESTION 44 Unit 1 experiences a hydraulic block ATWS.

Initial A TWS power is 40 percent.

SLC injection is successful.

With reactor power at 10 percent Feedwater is lost.

Reactor level falls to -135".

Which one of the following identifies the loads that will be shed for electrical distribution protection if the Main Turbine trips at this time?

A. TBCCW Pumps B. Service Water Pumps C. Instrument Air Compressors D. Turbine Building Chillers Proposed Answer B Applicant References None Explanation A Main Turbine trip will result in a Main Generator lockout. When the Main Generator lockouts trip with a LOCA initiation signal on low reactor level (-129") sealed-in, the Aux Buses undergo a Plant Aux load shed. Major 13.8 KV loads on the Aux Buses receive a momentary trip signal to ensure the Startup Buses are not overloaded when the Aux Buses fast transfer to the Tie Bus.

A TBCCW pumps are powered from 480V MCCs supplied by the Aux Buses. The power supplies to the TBCCW Pumps are not shed on the Plant Aux Load Shed.

B Correct. Service Water Pumps are shed on the Plant Aux Load Shed.

C Incorrect. Instrument Air Compressors are locked out for 10 minutes on a -129" signal, but only if a Loss of Offsite Power has occurred.

D Incorrect. The TB Chillers are powered from the ESS Buses. This distractor is plausible in that these chillers are shed on the LOCA signal, but are not affected by the status of the main generator.

10CFR55 41.4 Technical References E-102 Sht 31 E-145 Sht 1 Learning Objectives 11779 h CONFIDENTIAL Examination Material Page 89 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Question Source New Previous NRC Exam No Comments Operations Reviewer _ _I _ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 90 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam I RO I Tier 11 I Group 11 I Cognitive Level I Low I Level of Difficulty I 3 KJA 295016 AK3.03 Control Room Abandonment !Importance 1 3.5 Statement Knowledge of the reasons for the following responses as they apply to CONTROL ROOM ABANDONMENT : Disabling control room controls QUESTION 45 Which one of the following identifies the reason for disabling the Control Room HMis during performance of ON-100-009, Control Room Evacuation, for a Control Room fire?

A. Enable manual control of LV-10641, FW STARTUP RX LEVEL CONTROL VLV, at 1C1115 B. Prevent uncontrolled condensate injection by spurious opening of LV-1 0641, FW STARTUP RX LEVEL CONTROL VLV C. Prevent uncontrolled condensate injection by spurious re-opening of any HV-10603A(B)(C), RFP DSCH ISO VLV D. Ensure SETPOINT SETDOWN remains in effect to maintain reactor level as low as possible to avoid RCIC high-level trip Proposed Answer c Applicant References None Explanation In the event of a Control Room fire, ON-100-009 identifies the primary concern with fire-induced misoperation of ICS as re-opening of the HV-10603x RFP discharge valves. Re-opening of these valves during a controlled reactor cool down would result in uncontrolled condensate injection and vessel flooding. With the 10603 valves remaining closed, as long as the pumps are running Condensate should remain available to inject, and ICS can automatically maintain reactor level via the 10641 startup level control valve.

A Incorrect. The HMI at the 1C1115 panel is provided for observing performance of the LV-10641 valve, not to enable control. The 1C1115 view-only HMI is referenced in the Caution to ON-1 00-009 Step 4.6.

8 Incorrect. The LV-10641 valve is left in AUTO to allow ICS to be able to maintain reactor water level when Condensate Pumps are capable of injection. Spurious re-opening of the 10603x valves is the primary concern of allowing the Control Room HMis to remain functional during a Control Room fire.

C Correct. Spurious re-opening of the 10603x valves is the primary concern of allowing the Control Room HMis to remain functional during a Control Room fire.

D Incorrect. Setpoint Setdown is reset as part of the ON-1 00-009 Immediate Operator Actions to allow ICS to maintain reactor level in the normal band when Condensate Pumps are capable of injection. RCIC high-level trips are defeated when control is transferred to the RSDP.

10CFR55 41.10 Technical References ON-100-009 Learning Objectives 15320 Question Source New Previous NRC Exam No CONFIDENTIAL Examination Material Page 91 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Comments Operations Reviewer mj I 05114114 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 92 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam I RO I Tier 11 I Group 11 I Cognitive Level I Low I Level of Difficulty I 2 KIA 295037 EK3.01 SCRAM Condition Present and Reactor Power Above APRM Downscale or Unknown I Importance 14.1 Statement Knowledge of the reasons for the following responses as they apply to SCRAM CONDITION PRESENT AND REACTOR POWER ABOVE APRM DOWNSCALE OR UNKNOWN : Recirculation pump trip/runback QUESTION 46 Which one of the following describes why Recirc Pumps are run back to minimum speed for an ATWS where RPS fails to trip at rated power?

A Limit development of potentially fuel-damaging power oscillations B. Anticipation of a Recirc LIM1 runback when reactor level is lowered C. Reduce dilution of Standby Liquid Control boron by circulation through the recirc piping D. Prevent containment heatup due to tripping the Main Turbine and exceeding bypass valve capacity Proposed Answer D Applicant References None Explanation In an ATWS at rated power with a failure of RPS to trip, the immediate priority in executing E0-000-113 is to lower reactor power. After SLC is initiated recirc pumps are tripped for a rapid power reduction. Prior to tripping recirc pumps, if any steam-driven turbine is in operation recirc speed is reduced to minimum first. This is to prevent high-level trips of the steam turbine.

A Incorrect. The reduction in recirc flow will actually make the development of large power oscillations more likely. SLC initiation and reactor level reduction are performed in part to compensate for the decrease in stability margin when recirc flow is reduced.

B Incorrect. No concern for anticipating the automatic runback is identified by E0-000-113. The only discussion of a LIM1 run back in Step LQ/Q-7 of E0-000-113 is that action is required to initiate a runback to minimum if a LIM1 runback has not occurred.

C Incorrect. SLC concentration and inventory limits are established full mixing of the boron solution in the recirc loops.

D Correct. Specifically, trip of the main turbine in an ATWS with no rod motion will likely result in power levels exceeding bypass valve capability. As a result, primary containment will be challenged per E0-000-113 Step LQ/Q-7.

10CFR55 41.5 Technical References E0-000-113 Learning Objectives 14613 Question Source New Previous NRC Exam No Comments Operations Reviewer _ _/_ __ Facility Representative _ _/_ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 93 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION BLANK PAGE CONFIDENTIAL Examination Material Page 94 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam I RO I Tier 11 I Group 11 I Cognitive Level I Low I Level of Difficulty I 2 KJA 295038 EK3.03 High Off-Site Release Rate I Importance 1 3.7 Statement Knowledge of the reasons for the following responses as they apply to HIGH OFF-SITE RELEASE RATE: Control room ventilation isolation QUESTION 47 Which one of the following identifies why the CREOASS system is initiated in the PRESSURIZATION mode in response to a Zone I or II isolation signal?

A. To ensure Control Room equipment OPERABILITY is maintained by providing a controlled environment during accident conditions B. To ensure Control Room equipment OPERABILITY is maintained by minimizing the intake of radioactive material in the Control Room C. To minimize dose to Control Room personnel because a LOCA resulting in high on-site and off-site release rates could be in progress D. To minimize dose to Control Room personnel because a fuel handling accident may have resulted in gross fuel cladding damage Proposed Answer c Applicant References None Explanation The applicant is asked to identify the bases for the Control Room isolation function (CREOASS actuation in the Pressurization mode) in response to a Zone 1 or 2 isolation signal.

The Zone 1 and 2 isolation signals are reactor level low (-38") and high Drywell pressure (1.72 psig). Initiating CREOASS in the PRESSURIZATION mode isolates the normal Control Room fresh air intake and aligns the intake to the CREOASS filter trains, ensuring the air intake is filtered before release into the Control Room.

A Incorrect. This distractor is describing the basis of the Control Room Floor Cooling systems, which maintain a controlled temperature environment in the Control Room in normal and accident conditions.

B Incorrect. While CREOASS does limit the intake of radioactive material into the Control Room atmosphere, the purpose of the system as described in TS Bases 3.7.3 is to limit personnel exposure, not ensure equipment remains within the assumed EQ.

C Correct. The purpose of the CREOASS initiation is to limit minimize dose to Control Room personnel by aligning the system to provide a source of filtered air if the event in progress degrades into a LOCA.

D Incorrect. This distractor is describing the basis of the CREOASS actuation on high secondary containment ventilation radiation levels, which are Zone Ill isolation signals, not Zone 1 or 2.

10CFR55 41.12 Technical References TS 3.7.4 Bases Learning Objectives 13057 Question Source New Previous NRC Exam No Comments CONFIDENTIAL Examination Material Page 95 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Operations Reviewer _ _I _ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 96 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam I RO I Tier 11 I Group 11 I Cognitive Level I Low I Level of Difficulty I 2 KIA 295026 EA1.03 Suppression Pool High Water !Importance 13.9 Temperature Statement Ability to operate and/or monitor the following as they apply to SUPPRESSION POOL HIGH WATER TEMPERATURE: Temperature monitoring QUESTION 48 Which one of the following identifies conditions when Suppression Pool temperature cannot be determined?

A. Control has been transferred to the Remote Shutdown Panel B. Suppression Pool temperature > 230 oF C. Suppression Pool level< 20.5 ft D. 1Y216 is de-energized Proposed Answer B Applicant References None Explanation Suppression Pool temperature is monitored by a network of 20 RTDs connected to 2 divisionalized SPOTMOS NUMAC panels with additional monitoring capability at the Remote Shutdown Panel. SPOTMOS calculates 3 average temperatures. The SPOTMOS RTDs are located at 20.5' SP level and approximately 3.5' SP level.

1) Bulk SP Temp is the preferred indication with SP level> 20.5'. It utilizes both upper and lower RTDs.

2) SPOTMOS average temp is available with SP level > 20.5' It utilizes upper RTDs only.

3) SPOTMOS bottom-average temp is available for SP level > lower RTD location. It utilizes only lower RTDs.

A Incorrect. SP temperature indication is available at the RSDP on Tl-15751 once control has been transferred to the RSDP per ON-100-009.

B Correct. SP temperature cannot be determined above 230 oF per E0-000-103 Step SP/T-1 bases. This is the upper limit for the RTD indication.

C Incorrect. This is the level at which the upper RTDs are located. 2 of the 3 average SP temperature measurements are lost, but the bottom average remains.

D Incorrect. All of the lower RTDs are powered from Division 1. This is the alternate power supply for the Division 1 SP temperature RTDs.

10CFR55 41.7 Technical References E0-000-103 SP/T-1 TM-OP-059Z Learning Objectives 10507 e Question Source New Previous NRC Exam No Comments Operations Reviewer _ _/_ __ Facility Representative _ _/_ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 97 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION BLANK PAGE CONFIDENTIAL Examination Material Page 98 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam I RO I Tier 11 I Group 11 I Cognitive Level I Low I Level of Difficulty 14 KJA 295004 AA1.01 Partial or Complete Loss of D.C. Power I Importance 1 3.3 Statement Ability to operate and/or monitor the following as they apply to PARTIAL OR COMPLETE LOSS OF D.C.

POWER : D.C. electrical distribution systems QUESTION 49 Unit 1 is operating at rated power.

During a routine panel test, the following annunciator panels are found to be non-responsive:

1C651 AR-104 Division 2 RPS AR-105 Main Turbine AR-1 06 Main Generator, Electrical 1C668 All annunciators Which one of the following identifies the first electrical distribution system to investigate?

A. 1D645, 125V DC B. 1D662, 250V DC C. 1D240, Instrument AC UPS D. 1Y246, Instrument AC Proposed Answer A Applicant References None Explanation The only direct means of monitoring the DC and 120V AC systems in the SSES Control Room is via annunciation on Control Room panels 1C651, on annunciator panel AR-106. Power for AR-106 is from ESS 125 VDC panei1D645.

A Correct. 1 D645 breakers 16 and 19 power the affected annunciator panels.

B Incorrect. This is a plausible choice, in that it is the Division 2 ESS 250 VDC system.

C Incorrect. This is a plausible choice, in that it is the 120V Instrument AC UPS powered from a dedicated battery backup.

D Incorrect. This is a plausible choice, in that it is the Class 1E 120V Instrument AC power for Division 2 from the D load group.

10CFR55 41.7 Technical References ON-102-640 AR-106-G17 Learning Objectives 10983 e Question Source New Previous NRC Exam No Comments CONFIDENTIAL Examination Material Page 99 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Operations Reviewer _ _I _ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 100 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam I RO I Tier 11 I Group 11 I Cognitive Level I High Level of Difficulty 3 KIA 295018 AA1.01 Partial or Complete Loss of Component Cooling Water Importance 3.3 Statement Ability to operate and/or monitor the following as they apply to PARTIAL OR COMPLETE LOSS OF COMPONENT COOLING WATER: Backup systems QUESTION 50 Which one of the following describes how Drywell cooling is provided following a loss of offsite power?

A. All previously running Drywell cooler fans automatically restart RBCCW automatically aligns to supply Drywell coolers ESW must be manually aligned to supply RBCCW heat exchangers B. All previously running Drywell cooler fans automatically restart RBCCW must be manually aligned to supply Drywell coolers ESW automatically aligns to supply RBCCW heat exchangers C. All Drywell cooler fans automatically restart, except the undervessel and reactor head area coolers RBCCW automatically aligns to supply Drywell coolers ESW must be manually aligned to supply RBCCW heat exchangers D. All Drywell cooler fans automatically restart, except the undervessel and reactor head area coolers RBCCW must be manually aligned to supply Drywell coolers ESW automatically aligns to supply RBCCW heat exchangers Proposed Answer A Applicant References None Explanation A loss of offsite power occurred. Drywell coolers all restart when the Diesel Generators re-energize the respective ESS Buses. RBCCW will automatically realign to supply cooling to the Drywell coolers due to a loss of power to both RBCW chilled water pumps. RBCCW heat sink to service water is lost, so RBCCW HX cooling must be realigned from Service Water to ESW.

A Correct. This describes the normal plant response to a loss of offsite power.

B Incorrect. RBCCW automatically aligns to the Drywell coolers, and ESW must be manually aligned to RBCCW.

C Incorrect. The undervessel and reactor head area coolers response differs from the other OW coolers under LOCA, not LOP, conditions.

D Incorrect. The undervessel and reactor head area coolers response differs from the other DW coolers under LOCA, not LOP, conditions. RBCCW automatically aligns to the Drywell coolers, and ESW must be manually aligned to RBCCW.

10CFR55 41.4 Technical References ON-104-001 E-224 Sht 1 E-216 Sht 4, 8, 9 TM-OP-073 Learning Objectives 11191 b CONFIDENTIAL Examination Material Page 101 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Question Source Bank ILO LXR TMOP073118821001 Previous NRC Exam No Comments Operations Reviewer _ _I _ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 102 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam I RO I Tier 11 I Group 11 I Cognitive Level I Low I Level of Difficulty I 3 KIA 295030 EA2.03 Low Suppression Pool Water Level I Importance 13.7 Statement Ability to determine and/or interpret the following as they apply to LOW SUPPRESSION POOL WATER LEVEL : Reactor pressure QUESTION 51 Which one of the following identifies when bypassing interlocks and re-opening MSIVs is allowed to lower reactor pressure, in accordance with E0-000-112, Rapid Depressurization?

A. HCTL violated in ATWS, initial A TWS power < 5 percent and SLC not initiated B. Primary Containment pressure approaching 65 psig C. Reactor pressure > 95 psig with 4 SRVs open D. Suppression Pool level< 5 ft Proposed Answer D Applicant References None Explanation The question requires the determination of whether alternate RPV vent paths are required to accomplish Rapid Depressurization per E0-000-112. The question requires the applicant to interpret the effect of low Suppression Pool level when reactor pressure must be reduced via Rapid Depressurization in EOPs to determine the correct answer.

A Incorrect. In an ATWS, bypassing interlocks and re-opening MSIVs is allowed per Step LQ/P-5 of E0-000-113, but only when SLC is required. SLC is not required in this choice. With HCTL violated in a low-power ATWS, Rapid Depressurization is required with SRVs.

B Incorrect. PC pressure approaching 65 psig requires terminating injection into the reactor and PC from external sources via overrides in E0-000-102 and -103. No special direction regarding reactor depressurization is provided.

C Incorrect. Reactor pressure> 95 psig with 4 SRVs open does not allow use of alternate vent paths, per E0-000-112 Step RD-11.

D Correct. Suppression Pool level this low will result in uncovering SRV spargers and direct steam release to the Suppression Chamber airspace. Use of alternate RPV vent paths is required.

10CFR55 41.10 Technical References E0-000-112 Step RD-7, 11, 13 Learning Objectives 14593 Question Source New Previous NRC Exam No Comments Operations Reviewer mj I 5/14/14 Facility Representative _ _/_ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 103 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION BLANK PAGE CONFIDENTIAL Examination Material Page 104 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam I RO I Tier 11 I Group 11 I Cognitive Level I High I Level of Difficulty 14 KIA 295001 AA2.05 Partial or Complete Loss of Forced Core I Importance I 3.1 Flow Circulation Statement Ability to determine and/or interpret the following as they apply to PARTIAL OR COMPLETE LOSS OF FORCED CORE FLOW CIRCULATION : Jet pump operability QUESTION 52 Unit 1 experienced a reduction in core power and generator output.

Operators note the following parameter change as shown Indicated core flow Higher Core plate LlP Lower Recirc Pump B flow Higher Loop A JP flows Higher Loop B JP flows Lower Jet pump 9 flow Lower Jet pump 10 flow Higher Which one of the following identifies (1) the most likely cause of the observed indications?

(2) whether the jet pumps are still capable of performing their required safety function?

A. Displaced jet pump mixer Jet pump safety function is NOT maintained B. Loose jet pump mixer Jet pump safety function is NOT maintained C. Loose jet pump mixer Jet pump 10 is INOPERABLE Jet pump safety function is maintained for all other jet pumps D. Plugged jet pump nozzle Jet pump 9 is INOPERABLE Jet pump safety function is maintained for all other jet pumps Proposed Answer A Applicant References None CONFIDENTIAL Examination Material Page 105 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Explanation ON-164-005 provides guidance on diagnosing jet pump failures. The reduction in core power, generator load and core plate t.P indicate actual core flow has lowered. The mismatch between JP 9 and 10 indicates one of these jet pumps has faulted. JP 10 flow higher, JP 9 flow lower and the opposite JP loop total flow higher are all consistent with a displaced jet pump mixer. This is confirmed by the rise in Recirc Pump B flow, as the displaced mixer allows the riser pipe to discharge directly into the downcomer.

Safety function of a jet pump is described in the TS 3.4.3 Bases. Jet pump structural integrity is required to ensure the core can be reflooded to 213 core height after the DBA LOCA.

A Correct. The symptoms presented are consistent with a displaced JP mixer. JP safety function is lost as 213 core flooding cannot be assured with a failed mixer.

B Incorrect. For a loose JP mixer the JP flow of both JP on the riser is expected to lower.

JP safety function is lost as 2/3 core flooding cannot be assured with a failed mixer.

C Incorrect. For a loose JP mixer the JP flow of both JP on the riser is expected to lower.

JP safety function is lost with the structural failure of 1 JP.

D Incorrect. For a plugged JP nozzle indicated core flow is consistent with actual JP flow.

Recirc Pump B flow would be lower due to the increased flow resistance of the plugged nozzle.

10CFR55 41.3 Technical References ON-164-005 TS 3.4.2 Bases Learning Objectives 11502 Question Source New Previous NRC Exam No Comments Operations Reviewer mj I 05114114 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 106 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam I RO I Tier 11 I Group 11 I Cognitive Level I Low I Level of Difficulty 14 KIA 295024 EA2.06 High Drywell Pressure I Importance 1 4.1 Statement Ability to determine and/or interpret the following as they apply to HIGH DRYWELL PRESSURE:

Suppression pool temperature QUESTION 53 Which one of the following identifies a set of initial conditions that could lead to Primary Containment pressure exceeding the design limit if a design-basis Loss of Coolant accident were to occur?

A. Drywell pressure at 0.6 psig Suppression Chamber pressure at 1 psig B. Suppression Pool temperature > 105 oF HPCI full-flow test in progress C. Both loops of Drywell spray inoperable D. 2 of 3 required Drywell cooler fan pairs inoperable Proposed Answer B Applicant References None Explanation The applicant is required to evaluate 4 postulated initial conditions to identify the initial condition that lies outside the assumptions of the DBA LOCA analysis such that the high Drywell pressure design limit could be exceeded.

A Incorrect. Both primary containment compartment pressures are within the TS 3.6.1.4 LCO requirements. Although the Drywell is typically slightly positive relative to the Suppression Chamber, the only specific requirements on AP is< 1.5 psid DW-SC per TS 3.6.1.4 and > -0.5 psid DW-SC to prevent opening vacuum breakers.

B Correct. This Suppression Pool temperature, combined with continued testing that results in adding heat to the Suppression Pool, could result in exceeding Drywell high pressure design limits in the DBA LOCA due to being outside the initial conditions assumed in the containment pressure and pool heatup analyses. TS 3.6.2.1 Condition C requires immediate action to limit continued SP temperature increase and hourly action to monitor SP temperature to ensure the reactor operating limit of 110 *F is not exceeded.

C Incorrect. Drywell spray is the primary means for rapidly lowering DW pressure following events that result in high Drywell pressure. However, functionality of RHR for DW spray is not required by Technical Specifications or the TRM.

D Incorrect. The operability of 3 pairs of Drywell cooler fans is required by TS 3.6.3.2. The safety function of the DW cooler fans is for containment atmosphere mixing post-LOCA to dilute any hydrogen produced throughout the entire DW volume. Action within 1 hour1.157407e-5 days <br />2.777778e-4 hours <br />1.653439e-6 weeks <br />3.805e-7 months <br /> is required if 2 of 3 pairs are inoperable, but the action is to verify the alternate hydrogen control function of containment nitrogen purge is available. The cooling function of the OW coolers is not required to be operable to ensure the DW pressure response post-LOCA is acceptable.

10CFR55 41.9 Technical References TS 3.6.2.1 Bases Learning Objectives 13430 CONFIDENTIAL Examination Material Page 107 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Question Source New Previous NRC Exam No Comments Operations Reviewer _ _I _ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 108 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam I RO I Tier 11 I Group 11 I Cognitive Level I Low I Level of Difficulty I 2 KIA 295023 2.4.18 Refueling Accidents I Importance 1 3.3 Statement Knowledge of the specific bases for EOPs.

QUESTION 54 Both units are operating at rated power.

Dry Fuel Storage cask loading operations are being conducted in the Unit 1 and 2 Spent Fuel Pools.

A loss of offsite power occurs . Both units scram from rated power.

During the loss of power a spent fuel bundle is dropped in the Unit 2 Spent Fuel Pool. The 818' elevation is evacuated due to high area radiation levels.

Both units enter the Secondary Containment control EOP (E0-1 00(200)-1 04) .

SGTS SPING release rate exceeds the HI alarm.

Reactor Building SPING release rate is less than 10 percent of the normal full-power rate .

Which one of the following describes the action allowed to be taken with regard to Secondary Containment ventilation per E0-1 00(200)-1 04, and why?

Note: ES-070-001 -Secondary Containment HVAC lsolation/SGTS Initiation ES-134(234 )-003 - Re-Establishing Reactor Building HVAC ON-159-002- Containment Isolation Sec Ctmt HVAC Action A. Implement ES-134-003 and re-start Maintain functionality of equipment located in Zones I and II normal HVAC Secondary Containment B. Implement ES-134-003 and re-start Minimize spread of airborne contamination Zones I and II normal HVAC between HVAC Zones C. Implement ES-070-001 to isolate Maintain personnel access to Secondary Zones I, II and Ill Containment during post-accident conditions D. Implement ON-159-002 to verify Ensure any potential release occurs through a Zones I, II and Ill isolated filtered and monitored release path Proposed Answer D Applicant References None CONFIDENTIAL Examination Material Page 109 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Explanation Restarting Reactor Building normal HVAC is allowed by E0-000-104 Step SC-3 under certain specific conditions. Restarting HVAC is important to re-establish building cooling, allowing personnel access and maintaining conditions in the RB within the environment qualifications of equipment important to safety located in the RB. Restoration of RB HVAC results in unfiltered releases from the secondary containment via the normal RB exhaust. Bypassing isolation logics and restoring normal ventilation is therefore not allowed when there is potential for radioactive release due to returning normal HVAC systems to service.

A Incorrect. With the loss of offsite power, normal RB HVAC is unavailable. With the loss of normal HVAC Zones I and II cannot be maintained at a negative pressure without being isolated and SGTS in-service. This is the basis for restoring normal RB HVAC when possible and allowed due to no rad concerns.

B Incorrect. With the loss of offsite power, normal RB HVAC is unavailable. With the loss of normal HVAC Zones I and II cannot be maintained at a negative pressure without being isolated and SGTS in-service. Isolation of Zone Ill does isolate the common recirculation space from the non-affected unit preventing the spread of airborne radioactivity to the unaffected unit.

C Incorrect. Personnel access to the Secondary Containment is enhanced with restoration of building cooling by restarting normal HVAC, not by isolating the normal ventilation systems. Performing ES-070-001 is not necessary as a full Zone 1-111 isolation and SGTS initiation occurred due to the los sof offsite power.

D Correct. Isolation of all HVAC Zones is necessary to ensure the release from the refueling accident on the 818' elevation occurs through a filtered and monitored release path. With the loss of offsite power, the potential spread of airborne radioactivity from the 818' elevation to Zones I and II would result in an unmonitored and untreated release as Zones I and II cannot be maintained at a negative pressure without being isolated and SGTS in-service.

10CFR55 41.10 Technical References E0-000-1 04 Step SC-3 Learning Objectives 14613 Question Source New Previous NRC Exam No Comments Operations Reviewer Facility Representative _ _I _ _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 110 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam I RO J Tier l 1 I Group l1 I Cognitive Level I High I Level of Difficulty I 3 KJA 295003 2.4.49 Partial or Complete Loss of A. C. Power I Importance 14.6 Statement Ability to perform without reference to procedures those actions that require immediate operation of system components and controls.

QUESTION 55 Units 1 and 2 are operating at rated power.

ESS Transformer T-111 experiences a transformer lockout.

ESS Bus 2C is de-energized by the transformer lockout.

Breaker 2A203-01, XFMR 111 TO BUS 2C, remains closed.

Which one of the following identifies the immediate action required in response to this condition?

A. Open breaker 2A203-01, ONLY B. Open breaker 2A203-01 Close breaker 2A203-08, XFMR 211 TO BUS 2C C. Turn XFMR 211 TO BUS 2C synchroscope on Close breaker 2A203-08, XFMR 211 TO BUS 2C D. Place Diesel Generator C governor control to isochronous Depress DG C start pushbutton Proposed Answer A Applicant References None Explanation With the electric plant in the normal alignment ESS Transformer T-111 is the normal feeder to ESS Bus 2C. On a transformer lockout the transformer feeder breaker from other Startup Bus opens, and all downstream feeders from the transformer open. For ESS Bus 2C this is 2A203-01. This breaker remaining closed represents a failure of a protective action to occur automatically. Per OP-AD-001 Section 6.4 the operator shall manually initiate the protective feature should it fail to occur automatically. In this case that is to open 2A203-01. Once 2A203-01 opens the bus transfer scheme to its alternate supply should occur automatically.

Energization of a dead ESS 4KV bus, if required, is performed per ON-004-002.

A Correct. 2A203-01 should have opened automatically on the transformer lockout. This is the only action required to be performed immediately in response to the transformer lockout.

B Incorrect. Immediate action to close breaker 2A203-08 is not allowed per 01-AD-006 Step 4.3.15.a.

C Incorrect. Operation of the ESS Bus 2C synchroscope is not required to respond to the situation. Procedural direction for turning on synchroscope must be followed per ON-004-002.

CONFIDENTIAL Examination Material Page 111 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION D Incorrect. Starting the DG will not re-energize the bus. The DG does not have a start signal, as the DG start logic still sees the 2A203-01 breaker closed. The DG start logic does not include a direct start signal on bus undervoltage, only normal and alternate feeder breakers open.

10CFR55 41 .10 Technical References AR-015-E01 OP-AD-001 Step 6.4 ON-1 04-203 Section 5.0 01-AD-006 Step 4.3.15b Learning Objectives 10121 Question Source New Previous NRC Exam No Comments Operations Reviewer mj I 05114114 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 112 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 4 KIA 295019 2.4.9 Partial or Complete Loss of Instrument Air Statement Knowledge of low power/shutdown implications in accident (e.g., loss of coolant accident or loss of residual heat removal) mitigation strategies.

QUESTION 56 Unit 1 is shutting down for a planned outage and is in Mode 3.

Feedwater pumps are shutdown and isolated.

Operators are preparing to establish Condensate long-path recirculation flow with the LV-1 0641 Startup Level Control valve.

A small leak develops in the Drywell. A reactor scram occurs on high Drywell pressure.

A loss of Instrument Air occurs.

Reactor level is -5", down slow.

Which one of the following describes the immediate availability of Condensate from the Control Room to restore reactor level, and the reason why?

Condensate Availability Reason A. NOT available Startup level control valve LV-1 0641 cannot be opened B. NOT available Condensate Filtration System inlet and outlet valves fail closed C. Available Startup level control bypass valve HV-10640 valve remains functional D. Available Startup level control valve (LV-1 0641) fails as-is Proposed Answer A Applicant References None Explanation A loss of instrument air has a number of effects on the Condensate system. The condensate pump min flow valves fail open, diverting Condensate back to the hotwell, minimizing the injection capability of the system at higher pressures. At lower pressures the system may be capable of some injection to the reactor. Condensate pumps are not directly affected by the loss of air, as pump cooling is maintained.

The startup level control valve LV-10641 fails as-is on a loss of air. The 10641 valve is closed in preparation for the long-path recirculation alignment A Correct. A flow path to align Condensate Pumps to inject to the reactor cannot be established in the Control Room. The LV-10641 was closed at the time of the loss of air and fails as-is.

B Incorrect. The CFS inlet and outlet valves fail as-is on a loss of 1/A.

CONFIDENTIAL Examination Material Page 113 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION C Incorrect. Condensate injection would not be available as the 10640 fails closed. This distractor is consistent with the misunderstanding of the method of operation of the 10640, due to the HV designation typically used for MOVs and the lack of automatic valve control.

D Incorrect. The LV-10641 fails as-is, closed in preparation to establish long-path recirc flow.

10CFR55 41.4 Technical References ON-118-001 Learning Objectives 11155 a Question Source Modified Bank Vision LOC_BASIC S-300000-RB0-10-002. Revised stem conditions and correct answer. Additional changes for revision of ON-118-001.

Previous NRC Exam No Comments Reference CR 2014-16675 for changes in LV-10641 operation.

Operations Reviewer _ _I _ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 114 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 3 KJA 295025 EK1.04 High Reactor Pressure Statement Knowledge of the operational implications of the following concepts as they apply to HIGH REACTOR PRESSURE : Decay heat generation QUESTION 57 Unit 1 is starting up at 14 percent power.

Reactor Feedpump B has been placed in Flow Control Mode, with valve control for all 3 RFPs in MANUAL, due to a suspected software error in ICS.

The reactor is manually scrammed due to trip of both Recirc Pumps, per ON-100-101, Scram, Scram-Imminent.

In the scram report, one minute after scram, reactor pressure is reported as 790 psig, down slow, with MSIVs open.

Which one of the following characterizes the reactor pressure response, and the prompt operator action required in response to these conditions?

Reactor pressure response Operator action A. Lower than expected Close MSIVs due to PCIS malfunction B. Lower than expected Close bypass valves with the manual jack C. Expected Close MSIVs to prevent violating cooldown rate D. Expected Manually align Feedwater in startup level control to prevent uncontrolled injection Proposed Answer D Applicant References None Explanation Following a reactor scram from low-power (approximately 14 percent) at beginning of cycle, core decay heat is at a minimum and reactor pressure following a scram will be slow to recover. Prompt action with reactor pressure at 790 psig and going down will be required to ensure FW realigns to the startup level control alignment.

Operation at 11-15% RTP with a RFP in FCM is allowed by G0-1 00-102.

Low reactor pressure following a low-power scram is expected. The plant-reference simulator shows reactor pressure at 750 psig and lowering 150 seconds after a manual scram with no recirc pumps running.

A Incorrect. Conditions for an automatic closure of the MSIVs were not met as the reactor was manually scrammed from power. ON-100-101 directs placing the Mode switch to SHUTDOWN to scram the reactor, bypassing the MSIV closure on low pressure.

B Incorrect. No reason to expect bypass valve malfunction is provided in the stem. The manual jack would be ineffective in closing failed open bypass valves.

CONFIDENTIAL Examination Material Page 115 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION C Incorrect. Prompt action to close MSIVs is not procedurally directed for these conditions. Additional actions to close MSL drains, secure a RFP, and realign aux steam to secure normal steam loads should be attempted first.

D Correct. With the initial low reactor pressure this low and trending down, action to realign FW to startup level control is appropriate. E0-100-102 Step RCIP-1 will provide direction for this action once E0-1 00-102 is entered.

10CFR55 41.5 Technical References OP-145-001 Att A E0-000-102 Step RCIP-1 G0-100-102 ON-100-101 Learning Objectives 16095 Question Source New Previous NRC Exam No Comments Operations Reviewer mj I 06103114 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 116 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam I RO I Tier 11 I Group 11 I Cognitive Level I Low I Level of Difficulty I 2 KIA 295006 AK3.06 SCRAM I Importance 1 3.2 Statement Knowledge of the reasons for the following responses as they apply to SCRAM : Recirculation pump speed reduction QUESTION 58 Which one of the following identifies the reason the Recirc Pumps run back to LIM1 following a reactor scram at power?

A. To reduce power in the upper portion of the core by increasing voiding B. To minimize reactor level shrink during the scram transient C. To provide a redundant method of core power reduction D. To maintain Recirc Pump NPSH Proposed Answer D Applicant References None Explanation The Recirc Pumps runback to LIM1 on a reactor scram on a +13" reactor level signal or low FW flow. The purpose of this run back on low level is to maintain recirc pump NPSH due to the loss of static head to the recirc pump suctions. The purpose of the low FW flow run back is to maintain recirc pump NPSH with higher temperature water in the downcomer.

A Incorrect. This is the reason for the EOC-RPT function, which trips the recirc pumps to lower power to improve MCPR margin during the turbine trip transient.

B Incorrect. Reducing recirc pump speed has the effect of raising downcomer levels, but this is not done to affect reactor level during the scram transient.

C Incorrect. This is the reason for the ATWS-RPT function, which trips the recirc pumps to off on lower reactor levels which could be indicative of an ATWS condition.

D Correct. The basis for the LIM1 run back on low reactor level is to limit recirc pump speed to maintain NPSH.

10CFR55 41.5 Technical References AR-102-C01 TM-OP-064E Learning Objectives 16026 Question Source New Previous NRC Exam No Comments Operations Reviewer _ _I_ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 117 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION BLANK PAGE CONFIDENTIAL Examination Material Page 118 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam I RO I Tier 11 I Group I 2 I Cognitive Level I High I Level of Difficulty 14 KJA 295002 AK1.04 Loss of Main Condenser Vacuum I Importance 1 3.0 Statement Knowledge of the operational implications of the following concepts as they apply to LOSS OF MAIN CONDENSER VACUUM: Increased Offgas flow QUESTION 59 Unit 1 is operating at rated power.

Annunciator STEAM SEAL EVAP HI-LO LEVEL (AR-119-801) is received .

Seal Steam Evaporator level indicated on Ll-10749, SSE LEVEL, indicates -2.5 inches, down fast.

Which one of the following identifies (1) the appropriate action to take to clear the alarm?

(2) the action required if Seal Steam is lost and CANNOT be recovered?

Action to clear alarm Action if Seal Steam lost A. Close SSE SLOWDOWN ISO, Scram the reactor HV-101761 Close MSIVs B. Close SSE SLOWDOWN ISO, Perform Scram Imminent Actions HV-101761 Place second Offgas charcoal subtrain in-service C. Open SSE LEVEL BYPS, Scram the reactor HV-1 0750 Close MSIVs D. Open SSE LEVEL BYPS, Perform Scram Imminent Actions HV-10750 Place second Offgas charcoal subtrain in-service Proposed Answer c Applicant References None Explanation A malfunction in the condensate supply to the Seal Steam Evaporator has occurred as indicated by the SSE high-low level and indicated SSE level at the low-level alarm setpoint and lowering. Makeup to the SSE is required to maintain seal steam header pressure and prevent a loss of Main Condenser vacuum. The appropriate action to attempt to clear the alarm is to open the bypass around the normal SSE level control valve, HV-10750. If seal steam is completely lost, air intrusion past the turbine seals will result in a total loss of condenser vacuum. The reactor must be scrammed and the MSIVs must be closed in anticipation of the turbine trip and automatic MSIV isolations that occur on low condenser vacuum, combined with the possibility of seal damage due to excessive cold air flow across the hot labyrinth seals.

CONFIDENTIAL Examination Material Page 119 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION A Incorrect. The SSE blowdown isolation valve is the isolation valve to the continuous blowdown line to the Main Condenser. Closing this isolation valve will have a momentary effect on SSE level, but additional makeup will be required.

B Incorrect. The SSE blowdown isolation valve is the isolation valve to the continuous blowdown line to the Main Condenser. Closing this isolation valve will have a momentary effect on SSE level, but additional makeup will be required. Normally the SSE drains to the #2 FW heaters for improved thermal efficiency. While placing a 2nd charcoal train in-service is required for Offgas flow> 150 scfm, for a total loss of seal steam condenser vacuum cannot be maintained. A reactor scram and MSIV closure will occur.

C Correct. This will result in additional makeup to the SSE if condensate transfer is in service to clear the SSE low-level alarm . The reactor must be scrammed and the MSIVs must be closed in anticipation of the turbine trip and automatic MSIV isolations that occur on low condenser vacuum when seal steam is totally lost.

D While placing a 2nd charcoal train in-service is required for Offgas flow> 150 scfm, for a total loss of seal steam condenser vacuum cannot be maintained. A reactor scram and MSIV closure will occur.

10CFR55 41.5 Technical References AR-119-C02 ON-143-001 Step 3.7.4 Learning Objectives 10944 g Question Source New Previous NRC Exam No Comments Operations Reviewer mj I 05114114 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 120 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 3 KIA 295017 AK2.14 High Off-Site Release Rate Statement Knowledge of the interrelations between HIGH OFF-SITE RELEASE RATE and the following:

PCIS/NSSSS QUESTION 60 Units 1 and 2 are in Mode 1.

A loaded Dry Fuel transfer cask is being moved to its trailer in the Central Railroad Bay.

The Central Railroad Bay is aligned to Zone 3 HVAC.

The cask drops, resulting in significant fuel damage and a breach of the cask confinement boundary.

Reactor Building HVAC exhaust duct radiation monitors indicate as follows (mR/hr) :

Refuel Floor Refuel Floor Railroad High Wall Access Shaft Channel A (mr/hr) 4 6 15 Channel B (mr/hr) 3 9 Downscale Which one of the following identifies how offsite releases will be minimized in this condition?

Zone Ill Standby Gas Treatment A. Automatically isolates Both auto-start B. Automatically isolates Train A auto-starts C. Must be manually Train A auto-starts isolated D. Must be manually Must be manually isolated started Proposed Answer B Applicant References None Explanation A fuel handling accident in the Zone Ill space of secondary containment has occurred. A ventilation exhaust process rad monitor has tripped. This results in an isolation signal to Zone Ill and a start signal to the A train of SBGT and the A RB Recirc Fan. Actuation of either channel of Zone Ill isolation logic results in a full isolation of the Zone (1 of 2 dampers in-series). The B RR Access Shaft rad monitor appears to have failed, perhaps due to the accident, in the downscale conditions. This results in a DOWNSCALE/INOP alarm, but no INOP trip. No Channel B rad monitor is in the tripped condition.

A Incorrect. Only the Division 1 components will auto-start due to the A channel exceeding the TRIP setpoint. The downscale does not generate any auto-start signals.

CONFIDENTIAL Examination Material Page 121 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION B Correct. Zone Ill isolates and the A SBGT and RB Recirc Fan start.

C Incorrect. Manual isolation of Zone Ill is not required.

D Incorrect. One train of SBGT and a RB Recirc Fan auto-start, which is sufficient to assure the safety function of minimizing release from the accident. Zone Ill automatically isolates.

10CFR55 41 .9 Technical References AR-016-F12,H12 Learning Objectives 10879 e Question Source New Previous NRC Exam No Comments Operations Reviewer mj I 05114114 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 122 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 4 KIA 500000 EK3.07 High Containment Hydrogen Concentration Statement Knowledge of the reasons for the following responses as they apply to HIGH PRIMARY CONTAINMENT HYDROGEN CONCENTRATIONS: Operation of drywell vent QUESTION 61 Refer to the table below when answering this question.

Unit 1 experienced a fuel-damaging severe accident.

Adequate core cooling was lost and could not be re-established with both loops of RHR aligned for LPCI.

Current Containment combustible gas concentrations are as follows :

Hydrogen Oxygen Drywell 8 percent 4 percent Suppression 2 percent 5 percent Chamber Which one of the following describes the combustible gas control strategy for these conditions?

A. Vent the Drywell, to remove combustible gas from the Containment airspace to prevent a hydrogen deflagration B. Vent the Drywell, to maintain Containment pressure as low as possible in the event of a hydrogen detonation C. Spray the Containment, to cool non-condensibles and scrub fission products out of the Containment atmosphere before release D. Maximize Containment Recombiner operation, to reduce combustible gas concentrations TABLE 6 COMBUSTIBLE LIMITS OW OR SUPP CHMBR 6%

AND OW OR SUPP CHMBR 5%

CONFIDENTIAL Examination Material Page 123 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Proposed Answer A Applicant References None Explanation Combustible gas concentrations have exceeded the limits of E0-100-103 Table 6. E0-103 actions require recombiners be secured (Step PCIG-4) and EP-DS-001 entered (Step PCIG-7).

The strategies available in EP-DS-001 for combustible gas control include primary containment venting in addition to recombiner operation and containment spray.

A Correct. Venting the Drywell is the preferred combustible gas control strategy. Venting the DW is preferred to venting the Suppression Chamber for these conditions, as introducing the high H2 concentrations in the DW to the SC would create a combustible mixture.

B Incorrect. Attempting to lower DW pressure in anticipation of a hydrogen detonation is not a recognized method of H2 control.

C Incorrect. Containment spray is not available as all RHR pumps are required to attempt to restore adequate core cooling .

D Incorrect. Recombiner operation is precluded w ith a combustible mixture present in Containment.

10CFR55 41.5 Technical References E0-100-103 Step PCIG-4 EP-DS-001 Section 1 EP-DS-004 Att A Learning Objectives 12098 Question Source New Previous NRC Exam No Comments Operations Reviewer mj I 0610312014 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 124 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam I RO I Tier 11 I Group I 2 I Cognitive Level I High I Level of Difficulty 14 KJA 295008 AA1.07 High Reactor Water Level I Importance 1 3.4 Statement Ability to operate and/or monitor the following as they apply to HIGH REACTOR WATER LEVEL : Main turbine QUESTION 62 Unit 1 is operating at rated power.

The 1C004 instrument rack experiences a leak on the common Narrow Range level variable leg. All Narrow Range level indications on the 1C004 rack begin drifting lower.

Feedwater Level Control marks Narrow Range Level Channel B as DEVIANT.

Which one of the following identifies the effect on reactor level, and the operator action to be taken due to the level instrument malfunction?

Reactor level effect Operator action A. No effect Place 1C004 in Maintenance Bypass B. Reactor level lowers as FWLC reduces Insert a manual scram FWflow C. Reactor level rises as FWLC increases Select Narrow Range A or C for FWLC FWflow D. Reactor level rises as FWLC increases Scram the reactor FWflow Trip the Main Turbine and all Reactor Feedwater Pumps Proposed Answer D Applicant References None Explanation A variable leg leak on the 1C004 instrument panel results in slowly lowering reactor level indications on the N004A and C inputs to ICS and the N024A and B inputs to RPS, among others. With ICS marking the unaffected NR input N004B as DEVIANT, the ICS level selection logic is taking the A and C inputs as indicated reactor level. As these indications are drifting lower, ICS begins raising FW flow to attempt to raise level. With no feedback due to the instrument drift, actual reactor level continues to rise and will eventually reach +54" . With the NR A and C indicating low, no turbine trip signal will be generated.

A Incorrect. Actual level will rise. Placing 1C004 in Maintenance Bypass would be an appropriate response to the malfunction.

B Incorrect. Actual level will rise. The action of inserting a manual scram is consistent with the assumption that 1 division of RPS has failed due to multiple level instrument failures.

C Incorrect. While actual reactor level would rise, selecting one of the failed instrument channels for FWLC is an inappropriate action. This distractor is consistent with failing to identify the instruments associated with the C004 rack.

CONFIDENTIAL Examination Material Page 125 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION D Correct. Actual level is rising , and the Main Turbine and RFPT trips at +54" are disabled with the failure of the NR A and C lower.

10CFR55 41.7 Technical References ON-145-001 ON-145-004 Learning Objectives 10297 I Question Source New Previous NRC Exam No Comments Operations Reviewer _ _I _ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 126 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 2 KJA 295022 AA2.02 Loss of CRD Pumps Statement Ability to determine and/or interpret the following as they apply to LOSS OF CRD PUMPS : CRD system status QUESTION 63 Unit 1 has experienced an A TWS.

Operators maximized CRD per E0-100-113 Sheet 2.

Subsequently, CRD Pump suction pressure lowered to 6" HgV for 4 seconds, then returned to normal.

Annunciator CRD PUMP SUCTION FILTER HI DIFF PRESS (AR-107-C01) was in alarm momentarily, but has now cleared.

Which one of the following identifies the required operator action with regards to the CRD pump suction filter to continue to attempt to drift control rods?

A. Bypass the CRD Pump suction filter, ONLY B. Lower the output of the CRD flow controller THEN Bypass the CRD Pump suction filter C. Bypass the CRD pump suction filter THEN Restart both CRD Pumps D. Restart both CRD Pumps Bypass the CRD pump suction filter ONLY if the alarm re-flashes Proposed Answer c Applicant References None Explanation With both CRD pumps running the CRD pump suction filter has clogged and resulted in a trip of both CRD pumps on low suction filter. ON-155-007 Section 3.6 provides instructions for bypassing the pump suction filter and restarting CRD Pumps if tripped. In this event, both CRD pumps tripped on low suction pressure for more than the 3-sec TO.

A Incorrect. Both CRD Pumps have tripped. Bypassing the CRD pump suction filter alone is inadequate to attempt to drift control rods.

B Incorrect. Reducing the flow through the system would be an appropriate action if the CRD pumps were still running C Correct. Both CRD pumps have tripped. The pump suction filter must be bypassed before the pumps can be restarted and kept running.

D Incorrect. The alarm cleared only due to the trip of both CRD pumps. The CRD pumps will continue to trip on low suction pressure if the suction filter is not bypassed.

CONFIDENTIAL Examination Material Page 127 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION 10CFR55 41.6 Technical References AR-107-801, C01 ON-155-007 Section 3.6 Learning Objectives 11444 m Question Source Bank LOR LXR AD0451153041145 Previous NRC Exam No Comments Operations Reviewer mj I 0610312014 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 128 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 2 KIA 295007 2.4.6 High Reactor Pressure Statement Knowledge of EOP mitigation strategies.

QUESTION 64 Unit 1 is operating at rated power.

HPCI is out of service for routine maintenance.

The reactor scrams from rated power due to a loss of EHC.

Which one of the following identifies the first method of manual pressure control capable of stabilizing reactor pressure below the scram setpoint per E0-000-102, RPV Control?

A. Main Turbine Bypass Valves, using the manual jack B. Main Steam Line drains C. Align RCIC for CST-to-CST operation D. SRVs using an A-B-C sequence Proposed Answer D Applicant References None Explanation Following a loss of Main Turbine EHC the main condenser remains available. Of the methods listed and available, only SRVs have enough capacity to maintain reactor pressure below the RPS scram setpoint.

A Incorrect. The manual jack is unavailable due to the loss of EHC. This distractor represents application of a motor actuator to the bypass valves similar to that used for the Main Turbine turning gear.

B Incorrect. MSL drains remain available on a loss of EHC, and Main Condenser availability is maintained. However, drain capacity is limited and will result in reactor pressure rising above the scram setpoint and SRV cycling on the relief setpoint.

C Incorrect. Use of RCIC for pressure control is allowed, however the capacity of RCIC is limited and inadequate to prevent reactor pressure rising above the scram setpoint and SRV cycling on the relief setpoint.

D Correct. SRVs provide the initial RPV pressure relief on an abrupt loss of EHC, and subsequent manual use will be required to maintain pressure in a stable band below the scram setpoint until another system can be recovered or decay heat lowers to within the capability of available systems.

10CFR55 41.5 Technical References E0-000-1 02 Step RC/P-6 Learning Objectives 14593 Question Source New Previous NRC Exam No CONFIDENTIAL Examination Material Page 129 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Comments Operations Reviewer _ _I _ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 130 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 4 KIA 295029 EA2.03 High Suppression Pool Water Level Statement Ability to determine and/or interpret the following as they apply to HIGH SUPPRESSION POOL WATER LEVEL : Suppression pool water level QUESTION 65 Unit 1 experienced a fuel-damaging severe accident.

EP-DS-002, RPV and Primary Containment Flooding, is being performed.

The TSC has requested a determination if Containment water level has reached 116 ft, to see if core submergence has been achieved, using ON-159-003, Primary Containment Water Level Anomaly.

Which one of the following describes how the determination of Containment water level is to be made?

A. Plot Drywell pressure on the Containment level versus Drywell pressure graph, ONLY B. Ensure the Drywell has been vented to atmosphere THEN Plot Drywell pressure on the Containment level versus Drywell pressure graph C. Calculate the Drywell to Suppression Chamber flP THEN Plot the flP on the Containment level versus flP graph D. Ensure the Drywell has been vented to atmosphere THEN Calculate the Drywell to Suppression Chamber flP THEN Plot the flP on the Containment level versus flP graph Proposed Answer B Applicant References None Explanation TAF is a Containment water level of 116' . With a maximum indicated Containment water level of 49' on installed instrumentation, Suppression Chamber and Drywell pressures must be used to determine actual level. A level of 116' is in the Drywell above the Drywell pressure tap.

Therefore Drywell pressure can be used to directly determine the water level in Containment, if the Drywell is vented to atmosphere.

A Incorrect. Without ensuring the OW is vented to atmosphere, using DW pressure to determine Containment water level could give a false high reading.

B Correct. With the DW vented to atmosphere, the OW pressure directly correlates to Containment water level.

C Incorrect. This is the method used to determine Containment water level when level is above 49' and below the Drywell pressure tap at 64'.

CONFIDENTIAL Examination Material Page 131 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION D Incorrect. This is the method used to determine Containment water level when level is above 49' and below the Drywell pressure tap at 64'. Containment pressurized above atmosphere will affect both SC pressure and DW pressure readings equally.

10CFR55 41 .9 Technical References ON-159-003 EP-DS-002, Step RF-16 Learning Objectives 337 a Question Source Modified Bank 2011 LOC23 NRC Exam Question 64. Stem conditions changed to result in a different correct answer, minor editorial and formatting changes.

Previous NRC Exam Yes Comments Operations Reviewer _ _I _ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 132 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 3 KIA 2.1.37 Conduct of Operations Statement Knowledge of procedures, guidelines, or limitations associated with reactivity management.

QUESTION 66 Which one of the following evolutions requires a Reactivity Manipulation Package with a Reactivity Maneuver Request in accordance with OP-AD-338?

A. Lowering Recirc Pump speed from 35 to 30 percent for shutting down a Recirc Pump for Single Loop Operation per OP-164-001 B. Adjustments to recirc flow to maintain rated power, as xenon builds in following a plant startup C. Movement of partially withdrawn control rods for monthly surveillance testing performed as part of S0-156-001, Control Rod Exercising D. Movement of control rods performed as part of control rod scram time testing in Mode 1 per SR-155-004, Scram Time Measurement of Control Rods Proposed Answer D Applicant References None Explanation OP-AD-338 Section 6.3.2 provides a list of reactivity maneuvers that do not require a Reactivity Maneuver Package.

A Incorrect. Lowering recirc pump speed for recirc pump shutdown is specifically exempted in OP-AD-338 Step 6.3.2b(5).

B Incorrect. Changes in recirc flow to maintain a specified power level, in this case< rated power, are specifically exempted in OP-AD-338 Step 6.3.2b(2).

C Incorrect. Performance of the monthly control rod push-me/pull-me surveillance is covered by the exemption in OP-AD-338 Step 6.3.2a(3), as the single-notch control rod movements in the SO will not change power by 5 percent.

D Correct. Moving control rods for scram time testing per SR-1 (2)55-004i s not included on the list of activities exempted from requiring a RMP. SR 1(2)55-004 Step 5.4 states that a RMR will provide the authorization to stroke the control rods for performance of the test.

10CFR55 41.10 Technical References OP-AD-338 Section 6.3.2 NDAP-QA-0338 Step 5.13 SR-1(2)55-004 Step 5.4 Learning Objectives 14913 Question Source Bank AD044/14913/1 (LXR Ops Initial Bank)

Previous NRC Exam No Comments Operations Reviewer mj I 06/03/14 Facility Representative _ _/_ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 133 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION BLANK PAGE CONFIDENTIAL Examination Material Page 134 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam I RO I Tier I3 I Group I N/A I Cognitive Level I High I Level of Difficulty I 2 KIA 2.1.25 Conduct of Operations I Importance 1 3.9 Statement Ability to interpret reference materials, such as graphs, curves, tables, etc.

QUESTION 67 Refer to the figure on the following page when answering this question.

Unit 1 has experienced a large-break LOCA.

ECCS availability is limited. Only the following systems are injecting , and at the indicated flow rates:

Core Spray Pump 1B 3200 gpm Core Spray Pump 1C 3500 gpm RHR Pump 1C 8100 gpm Compensated Fuel Zone Level indication is NOT available.

Reactor pressure is 200 psig.

Which one of the following correctly identifies the lowest non-compensated Fuel Zone level indication that provides adequate core cooling under these conditions?

A. -161" B. -180" C. -205" D. -225" CONFIDENTIAL Examination Material Page 135 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION RPV Pressure (psig)

Fuel Zone Indicated 0 100 200 300 400 500 600 700 800 900 1000 1100 1- -110 -110 83 ~76 64 53 -48 37 -32 1- -120 -104 88 .;..,82 71 -66 -61 51 -46 1- -130 -114 -106 93 83 -79 .,..74 64 -60

- -140 -125 -117 -111 -105 -1()1 91 .. -87 78 -7"4

--150 -150 -136 -128 -:-122 -117 -113 -108 -104 -100 92 -88

- TAF -160 -147 -139 -134 -129 -125 -12.0 -117 -113 -1~ -106 -102 I

N

-170 -157

-150 -145 -141 -137 -133 -130 -126 -123 -119 -116 c - --

• H - -180 -168 -161 -157 -153 -149 -145 -142 -139 -136 -133 -130 E - * - - -- --

s 1- -190 -179 --173 -168 -164 -161 -158 -155 -152 -150 -147 -144 0 - -200 .* -200 -189 -184 -180 -176 -173 -170 -168 -165 -163 -160 -158 F -

-210 -200 -195 -191 -188 -186 -183 -181 -178 -176 -174 -172 w -

A - -220 -211 -206 -203 -200 -198 -195 -193 -191 -190 -188 -186 T -

E - -230 -222 -217 -214 -212 -210 -208 -206 -204 -203. -201 -200 R -

- . -240 -232 -228 -226 -224 -222 -220 -219 -218 -217 -215 -215

--250 -250 -243 -239 -237 -235 -234 -233 -232 -231 -230 -229 -229

- -260 -254 -251 -249 -247 -246 -245 -244 -244 -243 .-243 -243

- -270 -265 -262. -260 -259 -258 -257 -257 '-257 -257 -257 -257

- -280 -275 -273 .;,272 -271 -271 -270 -270 -270 -270 -270 -271

- -290 -284 -284 -283 -283 -282 -283 -283 -283 -284 -286 -285

- -300 -300 -297 -295 -295 -295 -295 -295 -295 -296 -297 -297 -299

- -310 -307 -306 -306 -306 -307 -307 -308 -309 -310. -311 -313 Proposed Answer B Applicant References None CONFIDENTIAL Examination Material Page 136 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Explanation For the given set of conditions the only available means of adequate core cooling is by submergence. While the combination of Core Spray flow is > 6350 gpm, spray cooling requires that flow from a single Core Spray loop to ensure the spray flow is effective at cooling the uncovered portion of the core by direct spray impingement.

Wide Range cannot be used to determine if adequate core cooling is satisfied as the indicatin provided is unstable and Fuel Zone is trending down, expected with degraded ECCS systems during a LOCA. With the compensated FZ indication not avaialble, to determine reactor level the nomograph of indicated Fuel Zone level to actual reactor level provided in Att D of ON-145-004 must be used.

A Incorrect. Fuel Zone level of -161" does assure adequate core cooling, but raising level that high is not required to establish adequate core cooling.

B Correct. For a reactor pressure of 200 psig Att D of ON-145-004 shows that actual reactor water is at TAF forts an indicated FZ level of -180".

C Incorrect. An indicated FZ level of -205" is below TAF. This is also the MZIRWL for steam cooling with no injection, but application of MZIRWL is inappropriate under the specified conditions because of ECCS flow.

D Incorrect. An indicated FZ level of -225" is below TAF. This level does correspond to the actual reactor level for spray cooling of -21 0", but application of spray cooling is inappropriate under the specified conditions because the total spray flow is split between two Core Spray loops.

10CFR55 41.10 Technical References ON-145-004, Step 3.3 and Att D E0-000-102 Step RCIL-2, RCIL-18 Learning Objectives 1480 Question Source New Previous NRC Exam No Comments Operations Reviewer mf I 05115114 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 137 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION BLANK PAGE CONFIDENTIAL Examination Material Page 138 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam I RO I Tier I 3 I Group I N/A J Cognitive Level I Low j Level of Difficulty I3 KJA 2.2.39 Equipment Control I Importance 1 3.9 Statement Knowledge of less than or equal to one hour Technical Specification action statements for systems.

QUESTION 68 Unit 2 startup is in progress.

Reactor pressure is 800 psig .

The in-service CRD Pump trips. The standby pump cannot be started.

Cross-tie of Unit 1 CRD to supply Unit 2 CRD has been directed.

Which one of the follfsowing correctly describes the conditions for placing the Mode Switch to SHUTDOWN per Technical Specifications?

A. 20 minutes after any one CRD accumulator is inoperable B. 20 minutes after the second CRD accumulator is inoperable AND Any inoperable accumulator is associated with a withdrawn control rod C. Immediately when one CRD accumulator is inoperable AND The inoperable accumulator is associated with a withdrawn control rod D. Immediately after the second CRD accumulator is inoperable AND Any inoperable accumulators are associated with a withdrawn control rod Proposed Answer c Applicant References None Explanation TS 3.1.5 applies. Condition C is entered on any HCU accumulator becoming inoperable due to low gas pressure with reactor pressure < 900 psi g. The action to verify the accumulator is associated with a fully inserted control rod is required immediately upon recognizing a loss of CRD charging water header pressure. If the inoperable accumulator is for a withdrawn control rod, Required Action C.1 cannot be performed within the Required Action Time and entry into Condition D is required.

A Incorrect. The 20 minute allowance of Condition B does not apply. The distractor is plausible in that this may be a prudent action to take based on the Note 2 to Step 3.2 of ON-255-007, but it is not required by Tech Specs.

B Incorrect. This is the correct action if the candidate were to incorrectly apply the requirements of TS 3.1.5 Conditions B and D as if reactor pressure were> 900 psi g.

C Correct. Condition C is entered on the first inoperable HCU accumulator, and Condition D requires placing the Mode Switch to SHUTDOWN immediately if the inoperable accumulator is associated with a withdrawn control rod.

D Incorrect. Condition C only requires 1 HCU accumulator to be inoperable for entry.

CONFIDENTIAL Examination Material Page 139 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION 10CFR55 41.10 Technical References ON-255-007 Step 3.2 Unit 2 TS 3.1.5 Learning Objectives 13430 Question Source Bank TMOP05511272511 LXR OPS_INITIAL_BANK Previous NRC Exam No Comments Operations Reviewer mj I 05115114 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 140 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 4 KIA 2.2.15 Equipment Control Statement Ability to determine the expected plant configuration using design and configuration control documentation, such as drawings, line-ups, tag-outs, etc.

QUESTION 69 Use your provided references to answer this question.

Unit 1 is operating at rated power when SRV G spuriously opens.

Indications for SRV G solenoids are as follows:

Hand switch (1 C601) AMBER lit, RED extinguished ADS A (1 C601) RED Extinguished ADS B (1C601) RED lit Hand switch (1 C628) AMBER lit, RED extinguished Hand switch (1 C631) AMBER extinguished, RED lit Which one of the following identifies the fuses required to be pulled to close the SRV?

A. F3B and F4B, ONLY B. F25B and F26B, ONLY C. F45 and F46, ONLY D. F3B and F4B AND F45 and F46 Proposed Answer A Applicant References M1-B21-129 Sht 5, 6 (redacted for power supply designation)

Explanation The indications provided are consistent with a spurious energization of the Division 2 ADS solenoid for SRV G, SV-14113G2.

A Correct. Fuses F3B and F4B supply power to the Division 2 ADS solenoid for SRV G, SV-14113G2 per M1-B21-129 Sht 5.

B Incorrect. Fuses F25B and F26B supply power to the Division 2 ADS solenoid indication for SRV G only, per M1-B21-129 Sht 6. Pulling these fuses would extinguish the lit indicators for SRV G, but would not close the SRV.

C Incorrect. Fuses F45 and F46 supply power to the normal relief operation solenoid for SRV G, SV-14113G3 per M1-B21-129 Sht 7. Pulling these fuses would have no effect with the Division 2 ADS solenoid energized for the SRV.

D Incorrect. Pulling fuses F45 and F46 is not required to close the SRV.

10CFR55 41.7 Technical References M1-B21-129 Sht 5, 6 CONFIDENTIAL Examination Material Page 141 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Learning Objectives 13701 Question Source New Previous NRC Exam No Comments Operations Reviewer mj I 05115114 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 142 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 3 KIA 2.3.13 Radiation Control Statement Knowledge of radiological safety procedures pertaining to licensed operator duties, such as response to radiation monitor alarms, containment entry requirements, fuel handling responsibilities, access to locked high-radiation areas, aligning filters, etc.

QUESTION 70 Unit 1 is operating at 2 percent power.

Maintenance personnel have entered the Drywell to perform emergent repairs on elevation 738'.

The PCOM notes that reactor power is rising unexpectedly.

Reactor power continues to rise until it exceeds 3 percent.

Which of the following actions must the PCOM take per NDAP-QA-0309, Primary Containment Access and Control?

A. Manually insert control rods to maintain power < 3 percent B. Immediately place the Mode Switch to SHUTDOWN C. Immediately direct personnel to move down to Drywell elevation 704' D. Notify HP to resurvey the 738' elevation of the Drywell Proposed Answer 8 Applicant References None Explanation NDAP-QA-0309 Section 6.5 provides guidance for control of reactor power during Drywell entries with the reactor operating. The primary purpose of the procedure is to prevent a significant rise in Drywell radiation levels.

A Incorrect. While control rod insertion to reduce power is allowed up to 3 percent power, in this situation the unexplained nature of the power excursion takes precedence and a reactor scram is required to prevent unexpected increases in Drywell radiation levels.

8 Correct. NDAP-QA-0309 requires the PCO stationed at the reactor controls to initiate a reactor scram by placing the Mode Switch to SHUTDOWN on any unexpected power increase.

C Incorrect. Immediately directing personnel to lower elevations of the Drywell may be appropriate, but is insufficient to prevent unexpected increases in Drywell radiation levels.

D Incorrect. Notifying HP to survey the Drywell would be appropriate, but is insufficient to prevent unexpected increases in Drywell radiation levels and unplanned dose to workers in the area.

10CFR55 41.12 Technical References NDAP-QA-0309 Learning Objectives 15314 CONFIDENTIAL Examination Material Page 143 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Question Source Bank LOC23 NRC (originally SRO question, but stem conditions and answer unchanged, so designated as bank question)

Previous NRC Exam Yes LOC23 Comments Operations Reviewer mj I 05115114 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 144 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 2 KIA 2.3.4 Radiation Control Statement Knowledge of radiation exposure limits under normal or emergency conditions.

QUESTION 71 An Alert has been declared due to radioactivity release rates .

The release is still in progress, but release rates have stabilized .

All Emergency Response facilities have been activated.

Which one of the following identifies, in accordance with EP-PS-1 00:

1) the maximum Emergency Exposure Extension that can be authorized to protect plant equipment to terminate the release?

2) whose approval , in addition to the Radiation Protection Coordinator, is required?

A. 10 Rem Shift Manager B. 10 Rem Emergency Director C. 25 Rem Shift Manager D. 25 Rem Emergency Director Proposed Answer B Applicant References None Explanation With the declaration of an Alert and release rates stable, no immediate threat is postulated to large populations and no actions for life-saving are required. The maximum Emergency Exposure Extension allowed by EP-PS-001 Att MM is 10 Rem .

EP-PS-001 Att MM requires approval from the Radiation Protection Coordinator (RPC) and either the Emergency Director or Recovery Manager. The TSC has been activated and therefore the Shift Manager has turned over the Emergency Director function to his relief.

With turnover of the ED function the Shift Manager can no longer approve Emergency Exposure Extensions.

A Incorrect. While this is the correct dose extension, the Shift Manager can no longer authorize the extension.

B Correct. This is the correct dose extension, and the ED approves dose extensions for on-site personnel.

C Incorrect. This dose extension is not warranted under these conditions; this is the limit for life-saving actions or protection of large populations. The Shift Manager can no longer authorize the extension.

CONFIDENTIAL Examination Material Page 145 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION D Incorrect. This dose extension is not warranted under these conditions. The ED may authorizes extensions, but not to this dose level.

10CFR55 41.12 Technical References EP-PS-001 Att MM Learning Objectives 15106 Question Source New Previous NRC Exam No Comments Operations Reviewer mj I 05115114 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 146 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 3 KIA 2.4.47 Emergency Procedures/Plan Statement Ability to diagnose and recognize trends in an accurate and timely manner utilizing the appropriate control room reference material.

QUESTION 72 Additional information to answer this question is provided on the next page.

Unit 2 experienced an ATWS. Initial ATWS power was 10 percent.

SLC is injecting.

Initial SLC Tank level was 1950 gal.

The STA reports SLC has injected 925 gal.

RPV water level is -90", down slow.

RPV pressure is being maintained with SRVs at 900 psig.

Suppression Pool temperature is 165 °F, steady.

Suppression Pool level is 24ft, steady.

Which one of the following identifies the level and pressure control strategy allowed by E0-200-113 in these conditions?

A. Raise reactor level to the normal band Lower reactor pressure to begin a cooldown B. Raise reactor level to the normal band Maintain reactor pressure in the current band C. Maintain reactor level in the A TWS band Lower reactor pressure to begin a cooldown D. Maintain reactor level in the ATWS band Maintain reactor pressure in the current band CONFIDENTIAL Examination Material Page 147 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION HEAT CAPACITY TEMPERATURE LIMIT RPV PRESS (PSIG) 80 70._.-.-.-.-.-.-.-.-.-.-.-.-~~~~~~~~~~~~~

12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 SUPPRESSION POOL LEVEL {FT)

TABLE 19 HSBW INJECTED INITIAL FINAL TANK TANK VOLUME VOLUME 2000 1150 1900 1060 1800 975 1700 891 1600 806 1500 722 1400 637 CONFIDENTIAL Examination Material Page 148 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Proposed Answer B Applicant References None Explanation E0-200-113 Table 19 shows the Hot Shutdown Boron Weight for an initial SLC Tank level of 1950 gal is 1060 gal. Current tank level, calculated from the specified amount of boron solution injected, is 1025 gal, so the HSBW has been injected and reactor level is directed to be raised to the normal band by E0-200-113 Step LQ/L-16. A change in the pressure control band is not allowed by E0-200-113 at this time as the Cold Shutdown Boron Weight has not yet been injected (step LQ/P-8).

A Incorrect. Raising level is directed, but initiating a cooldown is not allowed by steps LQ/P-6 which requires pressure be stabilized. The pressure band specified is plausible in that it is the reactor pressure that would allow injection from condensate and does not require exceeding the 100 °Fihr cooldown rate. The pressure band is not allowed by E0-200-113 step LQ/P-4 as reactor level is being maintained with the available injection systems and violation of HCTL is not imminent.

B Correct. Raising level is directed when the HSBW is injected. This is the correct pressure band until the CSBW is injected.

C Incorrect. This is the correct level band with HSBW not yet injected. The pressure band specified is plausible as noted for Distractor A.

D Incorrect. If HSBW had not yet been injected this would be the correct level and pressure band.

10CFR55 41.10 Technical References E0-000-113 E0-000-103 Learning Objectives 14594 Question Source Modified Bank PP0021145941097 LXR OP002_REQUAL_BANK. Changed stem conditions so HSBW had been injected, changing correct answer.

Previous NRC Exam No Comments 2012 LOR Biennial Operations Reviewer mj I 0610312014 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 149 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION BLANK PAGE CONFIDENTIAL Examination Material Page 150 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level 3 KIA 2.4.22 Emergency Procedures/Plan Statement Knowledge of the bases for prioritizing safety functions during abnormal/emergency operations.

QUESTION 73 Unit 2 experienced an ATWS . Initial ATWS power was 100 percent.

Subsequently offsite power is lost. MSIVs close due to the loss of power.

RHR Suppression Pool cooling is maximized .

Rapid Depressurization is now required due to low reactor level.

Which one of the following identifies how RHR is to be operated for the Rapid Depressurization ,

and why?

Action Basis A. Continue RHR operation in Maintain Suppression Pool Suppression Pool cooling temperature below the design limit B. Realign one division of RHR for Re-establish adequate core cooling LPCI and maintain Suppression Pool temperature below the design limit C. Realign both divisions of RHR for Allow manual control of LPCI flow to LPCI and prevent injection re-establish adequate core cooling D. Realign both divisions of RHR for Maximize LPCI injection to LPCI re-establish adequate core cooling Proposed Answer c Applicant References None Explanation The isolated ATWS has resulted in Suppression Pool temperatures exceeding the point where operation of both loops of RHR in SP cooling is required by E0-200-103 step SP/T-2. The only exception to the requirement to maximize SP cooling is if RHR pumps are continuously needed for adequate core cooling. In this case adequate core cooling has been lost, as a Rapid Depressurization due to low reactor level is required.

E0-200-113 step LQ/L-18 requires that injection from RHR Pumps be stopped before commencing a Rapid Depressurization to prevent uncontrolled injection and a large power excursion. A LPCI initiation signal is present on RHR as reactor level is below the initiation setpoint. OP-149-001. OP-149-001 Step 2.8.4 requires that the RHR Pumps be overridden OFF to prevent injection, as the LPCI injection valves will automatically open during the RD when reactor pressure falls below 420 psig.

A Incorrect. Continued operation of both Divisions of RHR in SP Cooling is not allowed by E0-200-103 due to the loss of adequate core cooling. Failure to prevent injection will result in uncontrolled injection from RHR during the Rapid Depressurization.

CONFIDENTIAL Examination Material Page 151 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION B Incorrect. While one division of RHR may be sufficient to restore adequate core cooling, failure to prevent injection on either division will result in uncontrolled injection.

C Correct. Both divisions of RHR must first be realigned for LPCI per Section 2.10 of OP-149-004 to prevent inadvertent draining of the RHR loops, then injection must be prevented.

D Incorrect. While both divisions of RHR may be required for adequate core cooling, injection must be prevented before the RD is initiated to prevent a power excursion from occurring due to uncontrolled injection.

10CFR55 41 .10 Technical References E0-000-103 Step SPIT-2 E0-000-113 Step LQ/L-18 OP-149-001 Section 2.8 OP-149-004 Section 2.10 Learning Objectives 10766, 14621 Question Source Bank INPO 29211 Previous NRC Exam No Comments Operations Reviewer mj I 05115114 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 152 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam I RO I Tier I3 I Group I N/A I Cognitive Level I Low I Level of Difficulty I 3 KIA 2.3.11 Radiation Control I Importance 1 3.8 Statement Ability to control radiation releases.

QUESTION 74 Unit 1 is operating at rated power when annunciator OFF-GAS HI RADIATION (AR-106-G03) is received.

The reading from Off Gas Pre Treatment Log Radiation Monitoring recorder (RR-D12-1R601) is determined to be valid and has just exceeded Lim1 .

Which one of the following identifies the next action required due to exceeding Lim 1?

A Scram the reactor and close the MSIVs and MSL drains B. Immediately reduce power to lower Offgas pretreatment activity to < 150,000 IJCi/sec C. Contact Chemistry to obtain an Offgas pretreatment sample D. Verify the Offgas system is not bypassed immediately Proposed Answer c Applicant References None Explanation Offgas Hi alarm and Offgas readings exceeding Lim1 require entry into ON-179-002. The AR for the Offgas Hi alarm directs checking the readings on the Offgas pretreat recorder and evaluating entry into the ON. ON-179-002 describes Lim1 as set 50 percent above nominal steady-state background levels. With Lim1 set at a relatively low level this facilitates compliance with TS 3.7.5 for Offgas activity by ensuring pretreat samples are obtained to determine the actual Offgas activity level.

A Incorrect. With Offgas pretreat readings just 50 percent higher than nominal background readings, MSL radiation levels will not have risen to the hi-hi alarm setpoint. Closure of the MSIVs is premature at this time.

B Incorrect. With Offgas pretreat readings just 50 percent higher than nominal background readings, actual Offgas activity levels remain at a very small fraction (<1 percent typically) of the TS 3. 7.5 LCO limit. Action to reduce power to maintain Offgas activity less than half of the TS 3.7.5 limit will not be required with pretreat rad levels just exceeding Lim1 .

C Correct. ON-179-001 Step 4.6 describes this action in response to Offgas pretreat readings above Lim1. Obtaining an Offgas pretreatment grab sample will allow determination of compliance with TS 3.7.5 limits.

D Incorrect. This is the TRM 3.7.7 Required Action and Completion Time for no operable Offgas pretreatment log radiation monitor. The question stem specifically identifies the reading as valid.

10CFR55 41 .11 Technical References AR-106-G03 ON-179-002 TS 3.7.5 TRM 3.7.7 CONFIDENTIAL Examination Material Page 153 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Learning Objectives 15318 Question Source New Previous NRC Exam No Comments Operations Reviewer _ _I _ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 154 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Exam I RO I Tier I3 I Group I N/A I Cognitive Level I Low I Level of Difficulty I 2 KIA 2.1.28 Conduct of Operations I Importance l 4.1 Statement Knowledge of the purpose and function of major system components and controls.

QUESTION 75 For the following RWCU following controls and indications Control/Indication Markings (1) HV-144-F102, RWCU SUCTION BROWN-striped pushbuttons (OPEN and CLOSE)

(2) HV-144-F001 , RWCU INLET IB ISO GREEN-collared handswitch (3) FI-G33-1 R609, RWCU INLET FLOW PURPLE-RED label Which one of the following correctly identifies the meaning of the hand switch and label colors?

A. (1) Containment isolation valve (2) Throttlable flow-control valve (3) Post-accident monitoring instrumentation B. (1) Throttlable flow-control valve (2) Containment isolation valve (3) Reactor vessel flow instrumentation C. (1) Containment isolation valve (2) Throttlable flow-control valve (3) DC-powered instrumentation D. (1) Throttlable flow-control valve (2) Containment isolation valve (3) Nuclear heat balance instrument Proposed Answer D Applicant References None Explanation The RWCU F102 valve is a throttleable system flow control valve. The RWCU F001 valve is an AC-powered containment isolation valve. The RWCU inlet flow indicator is used in the reactor core heat balance.

A Incorrect. The F102 is the throttable valve, F001 is the PCIV. PAM instrumentation is not specifically given a unique label color at SSES, but is plausible as a group of instrumentation that could be specially designated.

8 Incorrect. The F1 02 valve is throttleable, but the green collar designates ALL PCIVs, not just DC-powered PCIVs.

C Incorrect. The F1 02 valve is not a PC IV and is not DC-powered. The F001 is a PCIV and is not throttlable. The RWCU flow instrument is not DC-powered.

D Correct. The F102 is a throttlable valve, the F001 is a PCIV, and the RWCU flow instrument is a heat balance input.

10CFR55 41.7 CONFIDENTIAL Examination Material Page 155 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION REACTOR OPERATOR WRITTEN EXAMINATION Technical References TM-OP-077 E-165 Sht 6, 8 Learning Objectives 1376 Question Source New Previous NRC Exam No Comments Operations Reviewer mj I 05115114 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 156 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION Exam I SRO I Tier 11 I Group 11 I Cognitive Level I High I Level of Difficulty I 3 KIA 600000 AA2.04 Plant Fire On-Site I Importance 1 3.1 Statement The fire's extent of potential operational damage to plant equipment QUESTION 76 Unit 2 is operating at rated power.

A fire breaks out in the Unit 2 Remote Shutdown Panel.

All 3 SRVs operated from Remote Shutdown Panel open and cannot be closed .

The reactor is scrammed from rated power.

Which one of the following identifies an appropriate response to stabilize the unit under these conditions, per ON-013-001?

A. Allow Condensate to flood the reactor to the main steam lines Align Division 1 RHR in Suppression Pool cooling for long-term decay heat removal B. Isolate the RCIC and HPCI steam supplies Allow Condensate to flood the reactor to the main steam lines Align Division 2 RHR in Suppression Pool cooling for long-term decay heat removal C. Prevent uncontrolled Condensate injection by tripping all Condensate Pumps Maintain reactor level with RCIC , until it isolates, then Division 1 Core Spray D. Prevent uncontrolled Condensate injection by tripping all Condensate Pumps Maintain reactor level with HPCI , until it isolates, then Division 2 Core Spray Proposed Answer D Applicant References None Explanation Unit 2 is experiencing a fire in its Remote Shutdown Panel. Multiple SRVs open and the reactor is scrammed from rated power. The bases for ON-013-001 identifies that the preferred injection systems to use if available systems cannot maintain reactor level during s stuck-open SRV event is Division 2 Core Spray. The bases for ON-013-001 state that EOPs, ONs, GOs and other plant procedures will be utilized for shutdown.

A Incorrect. ON-013-001 does not identify a strategy of RPV flooding to respond to a fire in the Unit 2 Reactor Building. E0-200-102 requires reactor level maintained within the nominal band unless all reactor level indication is lost. For this fire, there is no threat identified to Division 2 indication, so entry into E0-200-114 for RPV Flooding is not expected. This is a strategy for a total loss of decay heat removal from ON-249-001 , but the plant design for a worst-case fire in any area is to establish safe shutdown with 1 division of ESF equipment. Division 2 RHR will be available in Shutdown Cooling, entry into ON-249-001 will not be required.

B Incorrect. This distractor adds the guidance to override HPCI per ON-013-001 Att D Step D.7&8 to the direction provided in Distractor A.

CONFIDENTIAL Examination Material Page 157 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION C Incorrect. While the actions to prevent uncontrolled condensate injection per E0-200-102 Step RCIP-1 is appropriate given the rapid lowering of reactor pressure expected for this event,. Use of RCIC should be limited due to the fire-induced MSO in the RSDP and the potential for similar MSO if RCIC is initiated.

D Correct. Actions to prevent uncontrolled condensate injection per E0-200-102 Step RCIP-1 are appropriate given the rapid lowering of reactor pressure expected for this event. Although the EOP bases describes the normal means of preventing uncontrolled injection is aligning Feedwater for Startup Level Control, in this transient action to trip the Condensate pumps would be appropriate. ON-283-001 Step 3.2 for stuck-open SRV provides similar guidance. ON-013-001 prefers the use of Division 2 systems due to the potential effects of the fire in the RSDP room per Step D.3 of Att D. Use of RCIC should be limited due to the fire-induced MSO in the RSDP and the potential for similar MSO if RCIC is initiated.

10CFR55 43.5 This is an SRO-Ievel question as the requirements of EO and ON procedures must be evaluated given the plant conditions, and available equipment, in order to select the appropriate mitigating procedures consistent with ON-013-001 requirements.

Technical References ON-013-001 Section 5.0, Att D Step D.3 E0-200-102, Step RCIP-1 ON-283-001 Step 3.2 Learning Objectives 15304 Question Source New Previous NRC Exam No Comments Operations Reviewer mj I 06123114 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 158 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION Exam I SRO I Tier 11 I Group 11 I Cognitive Level I High I Level of Difficulty I 2 KJA 700000 AA2.01 Generator Voltage and Electric Grid Disturbances

'Importance ,3.6 Statement Operating point on the generator capability curve QUESTION 77 Refer to the figure on the following page when answering this question.

Unit 1 is operating at rated power with main generator operation as shown.

Transient grid conditions result in oscillations in generator reactive load.

Main generator reactive load begins to oscillate between 200 and 300 MVAR.

Annunciator GEN VOLT REG AUTO TO MAN SETPOINT UNBALANCED (AR-106-C09) is in alarm .

Annunciator GENERATOR FIELD OVERVOLTAGE (AR-106-A06) remains clear.

Which one of the following describes the appropriate actions to direct in response to the conditions represented by the process computer display?

A. Verify the Auto Voltage Regulator automatically maintains Generator Field current

< 6000 amps Adjust HC-1 0002, MAN VOLT REG ADJUST, as necessary to clear AR-1 06-C09 B. Immediately transfer to the Manual Voltage Regulator Lower HC-10002, MAN VOLT REG ADJUST, until generator reactive load is

< 150 MVAR C. Reduce core power per the CRC instructions to lower generator load to restore positive margin to the capability curve Perform G0-100-012, Power Operations for an unplanned power reduction D. Immediately reduce core power per the CRC instructions to lower power by 5 percent Perform G0-100-012, Power Operations for an unplanned power reduction CONFIDENTIAL Examination Material Page 159 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION CONFIDENTIAL Examination Material Page 160 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION Proposed Answer c Applicant References None Explanation ON-198-001 is the governing procedure for operation outside the generator capability curve with the Main Generator voltage regulator in AUTO. The initial conditions presented show operation just inside the limits of the capability curve. The transient results in sustained operation outside of the capability curve.

A Incorrect. While the AUTO voltage regulator has automatic circuitry to lower field current < 5876 amps, this is only activated on a generator field overvoltage condition, which has not occurred. Adjusting the manual voltage regulator to match the AUTO regulator can be performed, but will not mitigate operation outside of the capability curve.

B Incorrect. Placing the manual voltage regulator in MANUAL is not authorized by the procedure. There is no basis for assuming misoperation of the voltage regulator in AUTO as the stem clearly indicates the excessive reactive loading is due to grid conditions.

C Correct. A power reduction is authorized by ON-198-001 . Performing the power reduction per the CRC instructions is the preferred method. G0-1 00-012 will have to be performed due to the unplanned power reduction.

D Incorrect. While a power reduction is authorized by ON-198-001 , 5 percent is more than required to obtain a positive margin on the capability curve. Note 2 to Step 3.5.3 of ON-198-001 allows up to 2 minutes for the AUTO voltage regulator to attempt to restore margin, so immediate action is not required. The 5 percent requirement is taken from ON-193-001 for a EHC control valve oscillation.

10CFR55 43.5 This is a SRO-Ievel question as evaluation of current generator conditions and selection of the appropriate procedure based on detailed knowledge of the mitigating strategy.

Technical References ON-198-001, Section 3.5, 5.0 Learning Objectives 15304 Question Source New Previous NRC Exam No Comments Click here to enter text.

Operations Reviewer _ _I _ _ __ Facility Representative _ _I_ _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 161 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION BLANK PAGE CONFIDENTIAL Examination Material Page 162 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION Exam I SRO I Tier 11 I Group I 1 I Cognitive Level I High I Level of Difficulty I 3 KIA 295005 AA2.02 Main Turbine Generator Trip I Importance 1 2.1 Statement Ability to determine and/or interpret the following as they apply to MAIN TURBINE GENERATOR TRIP :

Turbine vibration QUESTION 78 Unit 1 is shutting down for a forced outage. Reactor Power is 20 percent.

Annunciator TURB GEN BRG HI VIBRATION (AR-105-E05) alarms due to bearing #5 rotor and casing high vibration .

Operators trip the Main Turbine . The generator output breaker opens, but turbine speed does not lower.

Turbine bearing #5 vibration continues to rise. Vibration is currently 15 mils, up 5 mils every minute.

Which one of the following identifies the appropriate actions to direct to lower turbine vibration?

A. Close the MSIVs and MSL drains immediately Verify turbine speed begins to lower B. Place the Mode switch to SHUTDOWN immediately Close the MSIVs and MSL drains Verify turbine speed begins to lower C. Place the Mode switch to SHUTDOWN immediately Close the MSIVs and MSL drains Open the Main Condenser vacuum breakers if vibration does not lower D. Place the Mode switch to SHUTDOWN immediately Close the MSIVs and MSL drains Open the Main Condenser vacuum breakers after turbine speed lowers below 1200 rpm Proposed Answer c Applicant References None Explanation The Main Turbine has been tripped due to a high vibration condition. On the turbine trip leak by on the main turbine stop and control valves has resulted in the turbine remaining at speed.

Turbine vibration remains high and is rising slowly.

A Incorrect. Action to isolate steam flow to the main turbine is required by ON-193-002 Step 3.2. Although reactor power is below the bypass for reactor scram on turbine trip, directing an action, closing MSIVs, that will result in a reactor scram without first initiating a reactor scram is not allowed.

B Incorrect. Per ON-193-002 Step 3.2 the steam supply to the main turbine should be isolated if turbine speed does not lower after a turbine trip. Additional action to break vacuum is warranted at this time due to the rapid rise in vibration.

CONFIDENTIAL Examination Material Page 163 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION C Correct. Breaking vacuum is required because vibration is rising rapidly. Vibration is above the trip limit, so the "extremely high" threshold has been met. This is the procedural method for breaking vacuum per ON-193-002.

D Incorrect. While the actions specified are correct and in the correct sequence, the trend on turbine vibration will result in extremely high values before the turbine coasts down to 1200 rpm.

10CFR55 43.5 Technical References ON-193-002 Steps 3.2, 3.4 AR-105-E05 Learning Objectives 11041 Question Source New Previous NRC Exam No Comments Operations Reviewer_ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 164 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION Exam I SRO I Tier 11 I Group 11 I Cognitive Level I High I Level of Difficulty 14 KIA 295030 2.4.41 Low Suppression Pool Water Level I Importance 14.6 Statement Knowledge of the emergency action level thresholds and classifications.

QUESTION 79 Use your provided references and the information on the next page to answer this question.

Unit 1 experienced an electrical ATWS. Initial ATWS power was 100 percent.

Subsequently, MSIVs failed closed.

Reactor level is being maintained at -130", steady, by HPCI and RCIC at full flow.

Reactor pressure is being maintained 800-1050 psig using SRVs.

All attempts at control rod movement and boron injection fail.

Subsequently, a leak occurs in the Division 1 RHR Pump room .

Operators determine that the leak is on the suction of RHR Pump 1A and cannot be isolated.

The following conditions now exist Suppression Pool level 22 ft, down fast Suppression Pool temperature 170 °F, up slow Which one of the following identifies the action that will be required in response to this event, and the final Emergency Plan classification?

A. Rapid Depressurization when HCTL is violated Site Area Emergency B. Rapid Depressurization when reactor level falls below TAF Site Area Emergency C. Rapid Depressurization when HCTL is violated General Emergency D. Rapid Depressurization when reactor level falls below TAF General Emergency CONFIDENTIAL Examination Material Page 165 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION TABLE 18 SUPP POOL EQUALIZATION LEVELS EXPECTED LEAK LOCATION POOL LVL (FT)

HPCI 18 RCIC 19.5 RHRA 16 RHRB 17 CSA 16 CSB 19 Proposed Answer D Applicant References EP-RM-004 Tables F and M (redacted)

Explanation In this scenario an electrical ATWS with subsequent closure of the MSIVs has occurred. All energy from the reactor is being d irected to the Suppression Pool. HPCI, RCIC and SRVs are expected to be able to maintain reactor level and pressure in this condition, however the Suppression Pool will rapidly heatup and eventually violate the HCTL curve. To prevent inducing large amplitude power swings at low RPV pressures Rapid Depressurization due to HCTL is not performed until the reactor is shutdown with control rods. Table 18 of E0-100-103 shows the unisolable leak will result in SP level eventually falling to 16', the expected equalization level between the Suppression Pool and the Division 1 RHR room. When HPCI is isolated before 17' SP level reactor level will rapidly fall below TAF and a Rapid Depressurization will be required.

The current EAL classification on the SP leak remains a Site Area Emergency on EAL MS3.

When level falls below TAF with the containment breach a concurrent SAE in FS1 (clad LOSS, primary containment LOSS) will exist. However, aGE declaration is required on EAL MG3 when HCTL is violated.

A Incorrect. Rapid Depressurization on HCTL is not required by E0-100-103 for a high-power ATWS. An upgrade to aGE is still required on MG3 when HCTL is violated.

B Incorrect. While a Rapid Depressurization on low reactor level will be required when HPCI is isolated due to low SP level , an upgrade to a GE is still required on MG3 when HCTL is violated.

C Incorrect. Rapid Depressurization on HCTL is not required by E0-100-103 for a high-power ATWS. An upgrade to aGE on MG3 when HCTL is violated will be required .

D Correct. A Rapid Depressurization on low reactor level will be required when HPCI is isolated due to low SP level. An upgrade to aGE on MG3 when HCTL is violated will be required.

10CFR55 43.5 This question satisfies the requirements for a SRO-Ievel question as evaluation of plant conditions and declaration of the appropriate emergency classification is required. Additionally, detailed knowledge of the branch points for performing Rapid Depressurization due to low reactor water level and HCTL violation in a high-power A TWS is required.

Technical References E0-000-103 EP-RM-004 Learning Objectives 14594, 15549 Question Source New Previous NRC Exam No CONFIDENTIAL Examination Material Page 166 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION Comments Operations Reviewer mj I 05106114 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 167 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION BLANK PAGE CONFIDENTIAL Examination Material Page 168 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION Exam I SRO I Tier I 1 I Group 11 I Cognitive Level I High I Level of Difficulty I 3 KIA 295037 G2.4.35 SCRAM Conditions Present and Reactor 'Importance ,4.0 Power Above APRM Downscale or Unknown Statement Knowledge of local auxiliary operator tasks during an emergency and the resultant operational effects.

QUESTION 80 Unit 1 has experienced a failure of RPS to trip.

When ARI was initiated, a large number of control rods on the right side of the full core display continued to show not fully inserted All actions in the power leg of E0-1 00-113 were completed to the point of attempting control rod insertion.

ES-158-002, ARI and RPS Trip Bypass, was directed to be performed. The in-field portion of the ES was completed.

Annunciators RPS CHAN A1/A2(B1/B2) SCRAM DSCH VOL HI WTR LEVEL TRIP (AR-1 03(1 04)-F02), have subsequently cleared .

Which one of the following should be directed next in an attempt to insert the withdrawn rods?

A. Reset the scram, then insert a manual scram using the RPS manual scram pushbuttons in accordance with ES-158-002, RPS and ARI Trip Bypass B. Individually scram control rods in accordance with Attachment A of E0-100-113 Sheet 2 C. Vent the scram air header in accordance with the posted instructions D. Insert control rods in accordance with ES-155-001, Venting CRD to Insert Control Rods Proposed Answer c Applicant References None Explanation The conditions presented in the stem are consistent with an electrical ATWS, as indicated by the failure of the full core display to enter full-in/full-out mode, where ARI initiation or maximizing CRD flow were successful in inserting most of the control rods. ES-158-002 was directed for installation to defeat ARI to re-pressurize the scram air header for subsequent scram attempts. The RPS trip bypass portion of the ES were installed, but for no effect.

A Incorrect. The actions described are the next steps to perform to complete ES-158-002 to attempt a re-scram. However, as RPS has failed to trip this action will not have any effect and will not insert control rods.

B Incorrect. Individually attempting to scram control rods may have some success, but re-venting the scram air header to attempt to re-scram all withdrawn control rods is the preferred response.

C Correct. With RPS untripped and ARI defeated to re-pressurize the scram air header (indicated by the SDV now being drained), this action will vent the scram air header for an attempt to re-scram the control rods.

CONFIDENTIAL Examination Material Page 169 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION D Incorrect. This action would be effective in attempting to insert the control rods, but is not allowed to be used until all other methods have been attempted.

10CFR55 43.5 This question requires assessment of plant conditions (diagnosis of type of ATWS) and then selecting the appropriate procedure to continue with to make an effective attempt at control rod insertion.

Technical References E0-100-113 Learning Objectives 14594 Question Source New Previous NRC Exam No Comments Operations Reviewer _ _I _ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 170 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION Exam I SRO I Tier 11 I Group 11 I Cognitive Level I High I Level of Difficulty I 3 KIA 295021 G2.4.4 Loss of Shutdown Cooling I Importance 14.7 Statement Ability to recognize abnormal indications for system operating parameters that are entry-level conditions for emergency and abnormal operating procedures.

QUESTION 81 Unit 1 is cooling down following a scram from rated power. Reactor coolant temperature is 220 °F.

RHR Loop A is in Shutdown Cooling using RHR Pump 1A.

RWCU BLDN FLOW REG VLV, HV-144-F033, fails full open .

The ensuing level transient is terminated when RWCU isolates on low reactor level.

Which one of the following identifies the preferred course of action to re-establish decay heat removal and continue the cooldown?

A Re-enter E0-100-102 and raise reactor level> 90" with CRD and Condensate Perform ON-149-001 Attachment C, Quick Recovery of previously lnservice SOC Loop, to restore Division 1 RHR to Shutdown Cooling B. Re-enter E0-100-102 and raise reactor level> 13" by realigning Division 1 RHR to LPCI Restart a Reactor Recirc Pump per OP-164-001 Attachment D, Post Scram Recovery of A(B) Recirculation System Pump C. Perform ON-149-001 Attachment F, Alternate Decay Heat Removal RHR Loop B Injection with Suction from the Suppression Pool D. Raise reactor level per OP-149-002 Section 2.7, SOC Level Control Operation If RHR Pump 1A trips, restart RHR Loop A in SDC per OP-149-002 Section 2.1, Starting RHR A(B) in SOC in Mode 3 Proposed Answer A Applicant References None Explanation A loss of vessel level occurs due to malfunction of the RWCU blowndown valve. Reactor level falls to -38" before the level transient is terminated. As soon as RWCU isolates, CRD begins to recover level as the minimum allowed CRD injection rate per G0-100-005 Step 5.38.2.b Note.

RHR SDC isolated at +13", so decay heat removal has been lost.

A Correct. Entry into E0-100-102 is required on low reactor level. Step RC/L-4 specifies an allowed level band of +90" to +100" if SDC is in operation. CRD and Condensate both remain available for vessel makeup to raise level per G0-1 00-005. The preferred approach to restore decay heat removal is given by ON-149-001 Step 3.3.1, which directs restoring the previously in-service RHR loop to SOC if conditions permit.

CONFIDENTIAL Examination Material Page 171 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION B Incorrect. E0-100-102 will allow the use of LPCI to raise level above +13", but continuous operation of an RHR pump will not be possible under E0-100-102, thus providing only intermittent decay heat removal insufficient to meet TS 3.4 .. Restarting a Reactor Recirc pump would be necessary to maintain coolant circulation with limited, occasional LPCI flow.

C Incorrect. Entry into E0-100-102 is required. Performance ofthis ON section will eventually restore reactor level and decay heat removal, but is not preferred by E0-100-102 or ON-149-001 as RHR can be readily returned to SOC.

D Incorrect. Entry into E0-100-102 and ON-149-001 is required. Operation of RHR to restore reactor level using the referenced section of the procedure is not possible, as a RHR SOC isolation has occurred.

10CFR55 43.5 This is an SRO-Ievel question as an assessment of plant conditions is required to identity the lowest reactor level reached, and selection of the appropriate procedure to restore decay heat removal is required.

Technical References E0-100-102 ON-149-001 G0-100-005 Steps 5.35-5.38 Learning Objectives 15304 Question Source New Previous NRC Exam No Comments Operations Reviewer mj I 05115114 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 172 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION Exam I SRO I Tier 11 I Group 11 I Cognitive Level I High I Level of Difficulty I 3 KJA 295019 2.1.19 Partial or Complete Loss of Instrument Air I Importance 1 3.8 Statement Ability to use plant computers to evaluate system or component status.

QUESTION 82 Refer to the figure on the following page when answering this question.

Unit 1 was operating at rated power when the CIG 90 psig header to the Drywell isolated.

Efforts to restore CIG failed and the reactor was manually scrammed.

RPS failed to de-energize on the scram .

ARI and SLC failed to function.

Operators subsequently transition reactor level and pressure control to HPCI and SRVs.

Operators are now standing by to vent the scram air header.

Which one of the following actions will satisfy the requirements of E0-1 00-103, given the conditions in Containment as indicated on the plant computer, if all control rods insert when the scram air header is vented?

A. Maximize RHR Suppression Cooling per OP-149-004 to maintain operation below the HCTL limit for this reactor pressure B. Enter E0-1 00-112 and perform a Rapid Depressurization due to violation of the HCTL limit C. Lower reactor pressure regardless of cooldown rate to restore operation below the HCTL limit D. Re-enter E0-100-103 and maximize RHR Suppression Cooling per OP-149-004 to restore operation below the HCTL limit CONFIDENTIAL Examination Material Page 173 of 218

(")

0 z

c m

z

-1

)>

r m

)(

Ill 3

r en

~ m (5"

I z

3: Or-en

..

::aoc:

§I  :::aoen mNO

)>cnc:

Ozm

-t:;a::z:

On>

a_z CONTAINMENT ozz H2102 LIMITS "'tt=i>

m-en

a>-t CONTAINMENT >*m PRESS LIMIT -t!:)>

oos:

RPVSAT  :::amm TEMP LIMIT

==~*(")

amm

--tm-t

-t><:;a m>-

zs:n m-en xZ-t

)>)>)>

s:::::!::::!

-oo Zzz

)>

0 z

"C Ill co (1)

~

~

0 N

~

Ql)

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION Proposed Answer B Applicant References None Explanation An full-power isolated ATWS has occurred due to the failure of RPS and subsequent closure of MSIVs due to the loss of CIG. A R*Time display of the HCTL curve with current plant conditions is provided for use in determining the required action within E0-100-103. The conditions show operation in violation of the HCTL limit. When control rods are inserted progress in E0-100-103 can continue past SP/T-5. SP/T-8 requires a Rapid Depressurization per E0-100-112 when operation cannot be maintained within the HCTL limit.

A Incorrect. This is an appropriate action to initiate in response to an isolated ATWS, and is not specifically described as having been performed in the stem. However, this will not satisfy the E0-103 requirements for high SP temperature; a Rapid Depressurization will be required when all control rods are inserted.

B Correct. E0-103 Step SP/T-8 requires a Rapid Depressurization be initiated when HCTL cannot be maintained within limits, when all control rods are inserted.

C Incorrect. While this applies application of the bowtie per E0-100-102 Step RC/P-3, allowed once all control rods are inserted, once HCTL is violated a Rapid Depressurization is required by E0-103 Step SP/T-8.

D Incorrect. Re-entry into E0-100-102 will be required when E0-100-113 is exited when all control rods insert. Re-entry into E0-100-103 is not required. Execution of the SP temperature leg of E0-103 is stopped at step SP/T-5 with the ATWS in progress; execution of the procedure continues with Step SP/T-8 as soon as all control rods are inserted. SP/T-8 requires RD when HCTL cannot be MAINTAINED safe, no provision for violation and restoration of the limit is made.

10CFR55 43.5 This is an SRO-Ievel question as it requires knowledge of diagnostic steps and decision points in EOP-103 that result in transition to the Rapid Depressurization EOP contingency procedure.

Technical References E0-100-103 M-126 Sht 1 Learning Objectives 14622 Question Source New Previous NRC Exam No Comments None Operations Reviewer _ _/_ __ Facility Representative _ _/_ _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 175 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION BLANK PAGE CONFIDENTIAL Examination Material Page 176 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION Exam I SRO I Tier 11 j Group I 2 I Cognitive Level I Low I Level of Difficulty 14 KIA 295020 AA2.03 Inadvertent Containment Isolation I Importance 1 3.7 Statement Ability to determine and/or interpret the following as they apply to INADVERTENT CONTAINMENT ISOLATION: Reactor power.

QUESTION 83 Unit 1 is operating at rated power.

The RWCU return flow instrument fails downscale.

RWCU automatically isolates.

RWCU flow on PPC OD3 display turns WHITE.

Which one of the following actions is required?

A. Enter ON-100-006, Loss of Heat Balance Calculation Reduce core flow by 0.5 Mlbm/hr after 15 minutes B. Enter ON-1 00-004, Reactor Power Greater than Authorized Limit Immediately reduce core flow as necessary to obtain< 3952 MWth as indicated on PPC 15-minute average Core Thermal Power C. Enter ON-156-001, Unanticipated Reactivity Change Raise core flow as necessary to maintain PPC APRM average as close to 100 percent as possible D. Enter ON-100-006, Loss of Heat Balance Calculation Immediately enter a substitute value of RWCU flow of 300 gpm AND verify PPC 15-minute average Core Thermal Power turns YELLOW Proposed Answer A Applicant References None Explanation An actual RWCU isolation has occurred due to high differential flow. In this event this has resulted in an invalid RWCU flow indication, which will result in an invalid heat balance calculation. The appropriate procedure to enter is ON-100-006 for loss of the heat balance.

The necessary action within the ON is to reduce power a small amount below rated to ensure the licensed power level is not promptly violated.

A Correct. Entry into ON-1 00-006 is required due to the loss of the heat balance. The appropriate response per the ON is to reduce power by reducing core flow by 0.5 Mlbm/hr.

B Incorrect. This is the correct action if core thermal power remained valid and the loss of RWCU flow would result in a rise in indicated heat balance power.

C Incorrect. Entry into ON-156-001 is not specifically required for a loss of RWCU flow as none of the symptoms include loss of RWCU flow or the heat balance. The procedure does not address loss of the heat balance or loss of RWCU flow. Raising core flow when the heat balance has been lost violates the guidance of ON-1 00-006.

CONFIDENTIAL Examination Material Page 177 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION D Incorrect. While entry into ON-100-006 is required, action to substitute a RWCU flow is not immediately required. Consultation with Reactor Engineering is required. Use of 300 gpm as a substitute value is significantly over-conservative as actual RWCU flow is 0 gpm.

10CFR55 43.5 This questions is at the SRO level as assessment of plant conditions to identify why the RWCU flow input to the heat balance was lost (isolation, as opposed to failure of the return flow which does not input to the HB) and selection of the appropriate procedure to mitigate the loss of the heat balance.

Technical References ON-100-006 Learning Objectives 15304 Question Source New Previous NRC Exam No Comments Operations Reviewer mj I 05106114 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 178 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION Exam I SRO I Tier 11 I Group I 2 I Cognitive Level I High I Level of Difficulty I 3 KIA 295002 G2.4.21 Loss of Main Condenser Vacuum I Importance 14.6 Statement Knowledge of the parameters and logic used to assess the status of safety functions, such as reactivity control, core cooling and heat removal, reactor coolant system integrity, containment conditions, radioactivity release control, etc.

QUESTION 84 Unit 1 was manually scrammed due to Main Condenser air in-leakage.

All Feedwater pumps tripped on low vacuum after aligning to startup level control.

When HPCI was initiated for reactor level control , an unisolable steam leak in the HPCI room occurred.

The leak has resulted in temperatures in both the HPCI and RCIC pump rooms rising .

All actions in E0-1 00-104 to mitigate the effects of the steam leak have been attempted .

HPCI and RCIC room temperatures continue to rise and are approaching Maximum Safe values.

Reactor pressure is being maintained at 935 psig by Main Turbine Bypass valves.

Which one of the following describes the most rapid method of lowering reactor pressure allowed by E0-1 00-102, RPV Control, for this condition?

A. Enter E0-1 00-112 for Rapid Depressurization and open 6 ADS/SRVs B. Open 6 ADS/SRVs to anticipate Rapid Depressurization C. Fully open all Main Turbine bypass valves to anticipate Rapid Depressurization D. Open SRVs to reduce reactor pressure to 450-600 psig Proposed Answer c Applicant References None Explanation A primary system is discharging to the Secondary Containment and cannot be isolated. Two areas of Secondary Containment are approaching the Maximum Safe temperature. Per E0-100-104 step SC/T-8, a Rapid Depressurization will be required when both room temperatures exceed Max Safe. RD is imminent as the steam leak is unisolable and temperatures continue to rise.

E0-100-102 step RC/P-3 allows cooldown in excess of the TS limit when RD is anticipated. In this condition, even though condenser vacuum is degrading, E0-1 00-102 step RC/P-3 prefers directing as much energy as possible to a heat sink other than the Suppression Pool. The only requirements for use of the bypass valves to anticipate Rapid Depressurization is that the bypass valves be operable with an unisolated MSL and the Main Condenser still in service.

CONFIDENTIAL Examination Material Page 179 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION A Incorrect. Rapid Depressurization per E0-100-104 SCIT-8 is not required until 2 Secondary Containment area temperatures exceed Max Safe. That has not yet happened.

8 Incorrect. Use of SRVs to anticipate Rapid Depressurization per E0-1 00-102 is not allowed, only use of the bypass valves is authorized.

C Correct. This is the preferred method of utilizing a heat sink other than the Suppression Pool in anticipation of a Rapid Depressurization.

D Incorrect. While this method of pressure control is allowed by E0-100-102 Step RCIP-6 to allow injection from Condensate, discharging as much energy to a heat sink other than the Suppression Pool is preferred.

10CFR55 43.5 Technical References E0-100-102 Step RCIP-3 E0-100-104 Step SC/T-8 Learning Objectives 14624 Question Source New Previous NRC Exam No Comments Operations Reviewer mj I 0610312014 Facility Representative _ _/_ _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 180 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION Exam I SRO I Tier 11 I Group I 2 I Cognitive Level I High I Level of Difficulty 14 KJA 295022 AA2.03 Loss of CRD Pumps jlmportance 1 3.2 Statement Ability to determine and/or interpret the following as they apply to LOSS OF CRD PUMPS: CRD mechanism temperatures QUESTION 85 Use your provided references to answer this question.

Unit 1 is operating at rated power when the in-service CRD Pump trips on low suction pressure due to a pump suction filter high ~p condition .

Operators are dispatched to bypass the CRD pump suction filter per ON-155-007, Loss of CRD System Flow.

The following alarms are subsequently received CRD PANEL 1C007 HI TEMP (AR-103-H05)

CRD ACCUMULATOR TROUBLE (AR-103-H06)

Abnormal conditions are noted for the four Control Rods as shown below, ONLY.

270 355 15 1050 950 48 00 380 295 CRDM temp (°F) 11 950 925 HCU accum press (psig) 48 48 Control rod position 22 26 Which one of the following identifies the minimum required action(s) and latest completion time(s) that will restore compliance with ALL Technical Specifications LCOs applicable for this condition?

A. Restore Control Rod 26-11 HCU accumulator pressure within 8 hours9.259259e-5 days <br />0.00222 hours <br />1.322751e-5 weeks <br />3.044e-6 months <br /> Restore Control Rod 22-11 OR 26-15 CRDM temperature within 12 hours1.388889e-4 days <br />0.00333 hours <br />1.984127e-5 weeks <br />4.566e-6 months <br /> B. Restore Control Rod 26-11 HCU accumulator pressure within 1 hour1.157407e-5 days <br />2.777778e-4 hours <br />1.653439e-6 weeks <br />3.805e-7 months <br /> Restore Control Rod 22-11 AND 26-15 CRDM temperature within 12 hours1.388889e-4 days <br />0.00333 hours <br />1.984127e-5 weeks <br />4.566e-6 months <br /> C. Restore Control Rod 26-11 HCU accumulator pressure within 20 minutes Be in MODE 3 in 12 hours1.388889e-4 days <br />0.00333 hours <br />1.984127e-5 weeks <br />4.566e-6 months <br /> regardless of CRDM temperatures D. Declare Control Rod 22-11 INOPERABLE within 12 hours1.388889e-4 days <br />0.00333 hours <br />1.984127e-5 weeks <br />4.566e-6 months <br />, ONLY Proposed Answer A CONFIDENTIAL Examination Material Page 181 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION Applicant References TS 3.1.4 (redacted)

TS 3.1.5 (redacted)

Explanation Both CRD Pumps are unavailable due to a low suction pressure condition induced by high dP across the common pump suction filter. The loss of CRD cooling water flow will result in elevated temperatures in the CRD mechanisms eventually resulting in CRDM temperatures over 350 °F, the 01-055-003 limit requiring control rods to be declared SLOW. Similarly the loss of charging water header pressure will result in individual HCU accumulator pressure falling below the TS SR3.1.5.1 operability limit of 940 psi g.

A Correct. TS 3.1 .5 Condition A applies for a single inoperable HCU accumulator. If accumulator pressure is restored within the 8-hour Completion Time for either Required Action A.1 or A.2 that LCO is met and no additional action is required by TS 3.1.5, per LCO 3.0.2. Declaring either of Control Rods 22-11 or 26-15 INOPERABLE satisfies the total number and separation criteria of TS 3.1.4, in that only 1 OPERABLE control rod is SLOW, and no further action would be required per LCO 3.0.2 as the TS 3.1 .5 LCO is met.

B Incorrect. 1 hour1.157407e-5 days <br />2.777778e-4 hours <br />1.653439e-6 weeks <br />3.805e-7 months <br /> is the Completion Time for 2 or more inoperable HCU accumulators from TS 3.1.5 Condition B. CRDM temperatures are expected to be restored with a CRD pump and 01-055-003 only requires declaring the control rod slow while CRDM temperature is> 350 °F.

C Incorrect. 20 minutes is the Completion Time for restoring CRD charging water header pressure with 2 control rod accumulators inoperable and is not associated with restoring HCU accumulator pressure. CRDM temperatures are expected to be restored with a CRD pump and 01-055-003 only requires declaring the control rod slow while CRDM temperature is > 350 °F.

D Incorrect. While declaring control rod 22-11 INOPERABLE will satisfy LCO 3.1.4, in that no SLOW rod is adjacent to another OPERABLE SLOW rod, HCU accumulator pressure for control rod 26-11 renders that accumulator inoperable and action is required to satisfy TS 3.1.5.

10CFR55 43.2 This question is SRO-Ievel in that it requires determination of Required Action with Completion Times greater than 1 hour1.157407e-5 days <br />2.777778e-4 hours <br />1.653439e-6 weeks <br />3.805e-7 months <br />.

Technical References 01-055-003, Section 4.6 TS 3.1.4 TS 3.1.5 Learning Objectives 13112 Question Source New Previous NRC Exam No Comments Operations Reviewer mj I 05106114 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 182 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION Exam I SRO I Tier I 2 I Group 11 I Cognitive Level I High I Level of Difficulty I 2 KIA 263000 A2.02 D.C. Electrical Distribution I Importance 1 2.9 Statement Ability to (a) predict the impacts of the following on the D.C. ELECTRICAL DISTRIBUTION ; and (b) based on those predictions, use procedures to correct, control, or mitigate the consequences of those abnormal conditions or operations: Loss of ventilation during charging QUESTION 86 Both Units are operating at rated power.

Battery Charger 1D663 is in EQUALIZE per Maintenance request. All other 125/250V DC battery chargers are in FLOAT.

Battery Room Exhaust Fan OV116A trips. Standby fan OV116B fails to start.

Which one of the following describes ALL of the actions to be directed for the loss of battery room ventilation per ON-030-002, Loss of Control Structure HVAC?

A. Place Battery Charger 1D663 in FLOAT within 3 hours3.472222e-5 days <br />8.333333e-4 hours <br />4.960317e-6 weeks <br />1.1415e-6 months <br /> B. Open Unit 1 and 2 Battery Room doors Enter TRM LCO 3.7.3.7 for inoperable fire doors C. Place CREOASS in service in Pressurization/Filtration Mode Open Unit 1 and 2 Battery Room doors Enter TRM LCO 3.7.3.7 for inoperable fire doors D. Place CREOASS in service in Pressurization/Filtration Mode Open Unit 1 and 2 Battery Room doors Enter TRM LCO 3.7.3.7 for inoperable fire doors Place Battery Charger 1D663 in FLOAT within 3 hours3.472222e-5 days <br />8.333333e-4 hours <br />4.960317e-6 weeks <br />1.1415e-6 months <br /> Proposed Answer D Applicant References None Explanation Both divisions of Battery Room exhaust ventilation have been lost. One division of battery Room exhaust ventilation is required by TRO 3. 7.9 for operability of the equipment in the 125/250V DC battery rooms for cooling and combustible gas control.

Restoration of flow through the battery rooms is required to prevent buildup of combustible gases in the battery rooms. This is accomplished by starting CREOASS in the PRESSURIZATION/FILTRATION mode to bring in fresh air from the CS intake and circulate it through the Control Structure. Opening the battery room doors allows air circulation through the battery room sufficient for cooling and dissipating hydrogen.

A Placing the 1D663 charger in FLOAT limits hydrogen production from the charging 1D660 battery, but hydrogen is still being produced from all batteries due to operation of the associated chargers in FLOAT mode and building up in the isolated battery room spaces.

CONFIDENTIAL Examination Material Page 183 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION B Incorrect. Opening the doors to the battery rooms will allow airflow from the normal CS HVAC to enter the battery rooms, but hydrogen is still being generated from the batteries and will rise in concentration in the highest elevations of the Control Structure.

A purge of the CS airspace is required to limit hydrogen buildup. This is the correct TRM LCO for an inoperable fire door.

C Incorrect. Operation of CREOASS in the PRESSURIZATIONIFILTRATION mode will result in a constant feed and bleed on the CS airspace, limiting hydrogen buildup.

However, action to place all battery chargers in FLOAT is still required to limit hydrogen generation.

D Correct. Operation of CREOASS in the PRESSURIZATIONIFILTRA TION mode will result in a constant feed and bleed on the CS airspace, limiting hydrogen buildup. Placing all battery chargers in FLOAT limits hydrogen generation to the minimum possible.

10CFR55 43.5 This is an SRO-Ievel question as plant conditions must be evaluated to determine the effect of the isolation on battery room ventilation, the correct procedure selected to respond to the loss of ventilation, and application of license requirements for Appendix R compliance.

Technical References ON-030-002 Section 3.4, 5.0 OP-030-002 Section 2.10 TRO 3.7.9 TRM 3.7.3.7 Learning Objectives 10455 Question Source Bank LXR fLO TMOP4011130581003 Previous NRC Exam No Comments Operations Reviewer mj I 06123114 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 184 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION Exam I SRO I Tier I 2 I Group 11 I Cognitive Level I High I Level of Difficulty I 2 KIA 209001 A2.01 Low Pressure Core Spray I Importance 1 3.4 Statement Ability to (a) predict the impacts of the following on the LOW PRESSURE CORE SPRAY SYSTEM ; and (b) based on those predictions, use procedures to correct, control, or mitigate the consequences of those abnormal conditions or operations: Pump trips QUESTION 87 Unit 1 experienced a large-break LOCA at rated power.

Only Division 2 ECCS systems are available.

Reactor level was recovered with injection from Core Spray and RHR in the LPCI mode.

RHR Loop B has been aligned to Drywell and Suppression Chamber spray.

Core Spray Loop B maintained reactor level -140", steady, on Compensated Fuel Zone.

Core Spray Pump 1D then tripped .

Reactor level is now -200", steady, on Compensated Fuel Zone.

Which one of the following describes the next required action per E0-1 00-1 02, RPV Control, to assure adequate core cooling?

A. Initiate a Rapid Depressurization per E0-100-112 B. Initiate a Rapid Depressurization per E0-100-112 AND direct Core Spray Loop B flow throttled to < 3950 gpm per OP-151-001, Core Spray System C. Direct RHR Loop B re-aligned for LPCI injection to restore reactor level with flow through the RHR heat exchanger per OP-150-001, RHR System D. Contact the TSC to enter EP-DS-002 for RPV and Primary Containment flooding Proposed Answer c Applicant References None Explanation A large-break LOCA with degraded ECCS response will prevent completely recovering level in the RPV. The initial conditions in the stem are consistent with the long-term response to a DBA LOCA. The loss of Core Spray flow will result in level inside the shroud lowering and resulting in a loss of adequate core cooling by submergence. With 1 CS pump tripped adequate core cooling by spray does not exists. RC/L-21 requires maximizing RPV injection under these conditions.

A Incorrect. Conditions are already met for an automatic ADS initiation, with level< -129" for sufficient time elapsed after the LOCA to allow RHR to be realigned for containment cooling.

B Incorrect. Rapid Depressurization will have already occurred. The action to throttle Core Spray flow is required by OP-151-001 .

CONFIDENTIAL Examination Material Page 185 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION C Correct. Realigning RHR to LPCI is the next required action in response to the loss of adequate core cooling as the override at RCIL-19 must now be answered NO in response to the loss of design CS flow. Use of RHR for LPCI per Table 3 prompts directing flow through the RHR HX as soon as possible. In this condition, 10,000 gpm of RHR flow should be adequate to restore and maintain RPV level.

D Incorrect. The decision to enter RPV and PC flooding is not required until a determination is made that level cannot be restored and maintained> TAF. With Core Spray able to maintain level> TAF before a pump tripped, RHR will also be able to maintain level> TAF.

10CFR55 43.5 This questions is SRO-Ievel because knowledge of the diagnostic steps of the Alternate Level Control contingency EOP is required.

Technical References E0-102 Learning Objectives 14622 Question Source New Previous NRC Exam No Comments Operations Reviewer mj I 05106114 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 186 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION Exam I SRO I Tier I 2 I Group 11 I Cognitive Level I High I Level of Difficulty 14 KIA 262001 G2.1.32 A.C. Electrical Distribution jlmportance J4.0 Statement Ability to explain and apply system limits and precautions.

QUESTION 88 Unit 1 is in Mode 4 for a refueling outage. A Division 2 outage window is in progress.

Unit 2 is operating at rated power.

OATS526 is overheating due to a bad contactor. It has been removed from service to allow repairs. All loads supplied from OATS526 are de-energized.

TS LCOs TS 3.5.1 Emergency Core Cooling Systems - Operating TS 3.8.4 DC Sources - Operating TS 3.8.7 Electrical Distribution - Operating Which one of the following describes the Technical Specification LCO entry requirements for the DC systems affected on Unit 2 for this condition?

A. Enter TS 3.8.4 for 1 required DC battery charger inoperable No safety function determination per LCO 3.0.6 is required B. Enter TS 3.8.4 for 2 required DC battery chargers inoperable Perform a safety function determination per LCO 3.0.6 No loss of safety function exists C. Enter TS 3.8. 7 for 1 required DC distribution system inoperable No safety function determination per LCO 3.0.6 is required D. Enter TS 3.8.7 for 2 required DC distribution systems inoperable Perform a safety function determination per LCO 3.0.6 Enter LCO 3.0.3 for a loss of safety function in TS 3.5.1 Proposed Answer 8 Applicant References None Explanation The OATS526 is the normal supply to Division 2 ESS 480V LC 08526. To perform maintenance on the ATS the normal and alternate power supplies must first be de-energized. OP-105-001 Section 2.10 is the procedure governing this activity when performed for scheduled maintenance.

08526 is the power supply to the Division 2 125V DC battery chargers on Unit 1 and 2. The chargers will be de-energized when 08526 is de-energized. The associated DC buses 1D620 and 2D620 remain operable with the associated batteries operable.

NDAP-QA-0312 Att 8 defines the systems to which LCO 3.0.6 is applicable. DC sources are identified as a support system to the DC distribution systems required operable by TS 3.8.7.

CONFIDENTIAL Examination Material Page 187 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION A Incorrect. A safety function determination is required per NDAP-QA-0312. This distractor is plausible in that a specific exception to application of LCO 3.0.6 is made for TS 3.8.1 AC Sources, but not forTS 3.8.4 DC Sources. Specification of 1 DC source is plausible as the Unit 1 charger is required for Unit 2 operation, although not for Unit 1.

B Correct. Both the Unit 1 and 2 battery chargers are required to be operable for Unit 2 by TS 3.8.4. A safety function determination is required by NDAP-QA-0312.

C Incorrect. LCO 3.0.6 is applicable to the inoperable battery charger and entry into LCO 3.8.7 is not required. Specification of 1 DC distribution system is plausible as the Unit 1 DC distribution system 1D620 is required for Unit 2 operation, although not for Unit 1.

D Incorrect. LCO 3.0.6 is applicable to the inoperable battery charger and entry into LCO 3.8.7 is not required. A determination of a loss of safety function is plausible in that if LCO 3.0.6 is not applied with TS 3.8. 7 a loss of safety function in TS 3.5.1 does exist due to inoperability of Division 2 of Core Spray and RHR due to inoperable logic and breaker control power supplies, among other systems.

10CFR55 43.2 This is an SRO-Ievel question as determining the correct answer requires application of generic LCO requirements regarding safety function determination.

Technical References OP-105-001 Section 2.10 TS 3.8.4 NDAP-QA-0312 Learning Objectives 10976 Question Source New Previous NRC Exam No Comments This question satisfies the K&A as the examinee is required to apply P&L 2.10.2e of OP-105-001 and identify the specific LCOs that are applicable while the ATS is removed from service.

Operations Reviewer mj I 05106114 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 188 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION Exam I SRO I Tier I2 I Group 11 I Cognitive Level I High I Level of Difficulty I 2 KIA 223002 2.2.40 Primary Containment Isolation System I 'Importance ,4.7 Nuclear Steam Supply Shut-Off Statement Ability to apply Technical Specifications for a system .

QUESTION 89 Use your provided references when answering this question.

Unit 1 is operating at rated power.

PDIS-G33-1 N044B, RWCU B System High Flow, fails downscale.

Which one of the following identifies the action required by Technical Specifications for this condition?

A. Restore operability of the channel or place the channel in trip, within 24 hours2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br /> IF no action is taken , isolate RWCU within the following 1 hour1.157407e-5 days <br />2.777778e-4 hours <br />1.653439e-6 weeks <br />3.805e-7 months <br /> B. Isolate RWCU within 4 hours4.62963e-5 days <br />0.00111 hours <br />6.613757e-6 weeks <br />1.522e-6 months <br /> C. Isolate RWCU within 1 hour1.157407e-5 days <br />2.777778e-4 hours <br />1.653439e-6 weeks <br />3.805e-7 months <br /> D. Restore operability of the channel or place the channel in trip, within 1 hour1.157407e-5 days <br />2.777778e-4 hours <br />1.653439e-6 weeks <br />3.805e-7 months <br /> IF no action is taken , isolate RWCU within the following 1 hour1.157407e-5 days <br />2.777778e-4 hours <br />1.653439e-6 weeks <br />3.805e-7 months <br /> Proposed Answer A Applicant References TS 3.3.6.1 (partial)

TS 3.6.1.3 Explanation PDIS-G33-1 N044B is the RWCU system flow transmitter that provides the signal for the TS 3.3.6.1 Function 5.g isolation. Failure of the transmitter downscale renders the trip capability of the B trip channel lost and RWCU inlet 0/B isolation valve HV-144-F004 will not close on a valid high-flow condition. Isolation capability for Function 5.g is not lost, as the A trip channel will automatically close the HV-144-F001 valve accomplishing the isolation function.

A Correct. Loss of the trip capability in 1 trip channel for 24 hours2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br /> is allowed by TS 3.3.6.1 Condition A.

B Incorrect. This is the Required Action and Completion Time for an inoperable PC IV per TS 3.6.1 .3 Condition A.

C Incorrect. This is the Required Action and Completion Time for both PCIVs inoperable in a penetration per TS 3.6.1.3 Condition B.

D Incorrect. This is the Required Action and Completion Time for a loss of isolation capability for Function 5.g. The isolation capability of the A trip channel is maintained.

10CFR55 43.2 This is an SRO-Ievel question as it requires application of TS Required Actions >

with Completion Times> 1 hour1.157407e-5 days <br />2.777778e-4 hours <br />1.653439e-6 weeks <br />3.805e-7 months <br />.

Technical References TS 3.3.6.1 M1-B21-131 Sht 9 Learning Objectives 13180 CONFIDENTIAL Examination Material Page 189 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION Question Source Bank LXR LOR TMOP06111618015 Previous NRC Exam No Comments Operations Reviewer mj I 0610312014 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 190 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION Exam I SRO I Tier I2 I Group 11 I Cognitive Level I Low I Level of Difficulty 14 KJA 400000 2.1.20 Component Cooling Water I Importance 1 4.6 Statement Ability to interpret and execute procedure steps.

QUESTION 90 Unit 1 is operating at rated power. Unit 2 is starting up from a refueling outage, preparing to enter Mode 1.

A leak develops on the ESW Loop A supply piping to Diesel Generator C.

Both loops of ESW to DG C are isolated as part of the initial event response.

Which one of the following identifies the action(s) required, if any, to satisfy Technical Specification LCO 3.0.4 requirements to allow Unit 2 to enter Mode 1?

A. Unit 2 may enter Mode 1 without any other action as only 1 Technical Specification-required system is inoperable B. Perform a risk evaluation of 1 required ESW subsystem inoperable AND Implement the associated risk management actions C. Perform a risk evaluation of 1 required ESW subsystem inoperable and 1 required DG inoperable AND Implement the associated risk management actions D. Restore ESW Loop B to DG C per OP-054-001, ESW System OR Substitute DG E for DG C per OP-024-004, Transfer and Test Mode Operations of Diesel Generator E Proposed Answer D Applicant References None Explanation In the condition described, DG C has been made inoperable due to a leak in ESW with both loops to the DG isolated. A mode change is pending on Unit 2. The Note toTS 3.7.2 Conditions requires entry into LCO 3.8.1 for DGs made inoperable by inoperable ESW. With the DG inoperable, the Note to LCO 3.8.1 Conditions prohibits the use of LCO 3.0.4b risk-informed Mode changes for inoperable DG. NDAP-QA-1902 Step 6.8.2a states the same requirement.

A Incorrect. This represents mis-application of NDAP-QA-1902 Step 6.8.4. While this step would be applicable for 1 ESW subsystem inoperable, it may not be utilized when LCO 3.0.4b is prohibited, as is the case for an inoperable DG.

B Incorrect. This represents mis-application of NDAP-QA-1902 Step 6.8.5 and failure to correctly apply Step 6.8.2a.

C Incorrect. This represents mis-application of NDAP-QA-1902 Step 6.8.5 and failure to correctly apply Step 6.8.2a.

CONFIDENTIAL Examination Material Page 191 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION D Correct. DG C must be restored to OPERABILITY or substituted with an OPERABLE DG E to allow the mode change, to satisfy NDAP-QA-1902 Step 6.8.2a.

10CFR5 43.2 This is an SRO-Ievel question as it requires the application of generic LCO requirements (LCO 3.0.4).

Technical References ON-054-001 Step 3.4.8, 3.5 NDAP-QA-1902 Step 6.8 TS 3.8.1 TS 3.7.2 Learning Objectives 13426 Question Source New Previous NRC Exam No Comments Operations Reviewer mj I 0610312014 Facility Representative _ _I_ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 192 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION Exam I SRO I Tier J2 I Group I 2 I Cognitive Level I High I Level of Difficulty I 2 KIA 226001 A2.11 RHRILPCI: Containment Spray System Mode I Importance 13.0 Statement Ability to (a) predict the impacts of the following on the RHRILPCI: CONTAINMENT SPRAY SYSTEM MODE ; and (b) based on those predictions, use procedures to correct, control, or mitigate the consequences of those abnormal conditions or operations: Motor operated valve failures.

QUESTION 91 Refer to the figure on the following page when answering this question.

Unit 1 experienced a LOCA in the Drywell at rated power.

The reactor automatically scrammed.

E0-100-103 was entered and RHR was aligned as follows:

RHR Loop A Suppression Chamber spray RHR Loop 8 Suppression Pool cooling Subsequently, Drywell pressure continued to rise and Drywell spray was required .

When operators attempted to align RHR Loop A for Drywell spray, power to HV-151-F016A, DRYWELL SPRAY 08 ISO, was lost.

Current containment conditions are as follows:

Drywell pressure 28 psig, up slow Suppression Chamber pressure 25 psig, up slow Suppression Pool level 25 ft, down slow Which of the following should be directed in response to the failure of the RHR A Drywell spray valve, in accordance with E0-100-103?

A. Immediately perform E0-100-112, Rapid Depressurization due to containment pressure exceeding the Pressure Suppression Limit B. Direct a local operator to fully open HV-151-F016A, as sufficient Drywell overpressure exists to preclude exceeding the Drywell negative pressure limit C. Re-align RHR Loop 8 from Suppression Pool cooling to Drywell spray per OP-149-004, to maximize Drywell pressure reduction D. Place RHR Loop 8 in Drywell spray per OP-149-004, limiting flow through each flow path to < 10,000 gpm, to maximize decay heat removal CONFIDENTIAL Examination Material Page 193 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION PRESSURE SUPPRESSION LIMIT 40 38 i=' 36

!:. 34

~

w 32

[i

~

~

g 30 28 26 , ~

~

/'

D.. 24 z

0 22 v

~ 20 /

w 0:: 18 /

D.. ~

D.. 16 ~

J en 14 ~~

12

/

10 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 SUPPRESSION CHAMBER PRESSURE {PSIG)

Proposed Answer c Appl icant References None Explanation Primary containment is being challenged during a Drywell LOCA condition on Unit 1. Drywell pressure has risen above 13 psig and is continuing to rise to approach the PSL limit. Current conditions remain safe on the PSL curve. Attempts to spray the Drywell are appropriate before initiating RD due to approaching the PSL curve.

When RHR A was being placed in service the 08 DW spray valve failed . This is the throttle valve in the DW spray flowpath used to limit initial DW spray flow to prevent damage to the primary containment due to excessive negative pressure during the initial evaporative cooling phase. Failure of this valve precludes placing RHR A in service in OW spray per procedure.

A Incorrect. This is the action required by E0-100-103 if Suppression Chamber pressure exceeds the PSL limit. Drywell pressure above the PSL limit does not require any action .

8 Incorrect. Fully opening the RHR A F016A valve does not allow establishing 1000-2800 gpm flow for the first 30 seconds of DW spray operation, as SSES does not provide a DWSIPL curve.

C Correct. This action is allowed by E0-100-103 and OP-149-004. This will maximize the DW pressure reduction and if possible prevent exceeding the PSL limit.

D Incorrect. While placing RHR in both the SP cooling and DW spray modes is allowed by the note to Step 2.1 of OP-149-004, the RHR HX flow limit of 10,000 gpm still applies. No limit on total system flow of 20,000 gpm exists.

10CFR55 43.5 This is an SRO-Ievel question as it requires assessment of the availability of RHR A for the DW spray function due to the MOV loss and selection of the appropriate procedure to implement in response to the rising containment pressure and degraded RHR A system .

Technical References OP-149-004 Sect 2.1 E0-100-103 Step PC/P-7,8,9 CONFIDENTIAL Examination Material Page 194 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION Learning Objectives 10772 Question Source New Previous NRC Exam No Comments Operations Reviewer _ _I _ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 195 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION BLANK PAGE CONFIDENTIAL Examination Material Page 196 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION Exam I SRO I Tier I2 I Group I 2 I Cognitive Level I High I Level of Difficulty I 2 KIA 241000 2.4.34 Reactor/Turbine Pressure Regulating System I Importance 14.1 Statement Knowledge of RO tasks performed outside the main control room during an emergency and the resultant operational effects.

QUESTION 92 Unit 1 is operating at rated power.

A fire develops in the 1C651 panel. Turbine pressure set begins to lower uncontrollably as a result.

Operators place the Mode switch in SHUTDOWN and verify all control rods insert.

Control Room evacuation is ordered due to heavy smoke and flames. Immediate operator actions are NOT performed.

Operators proceed to the Remote Shutdown Panel to establish control per ON-100-009, Control Room Evacuation.

Which one of the following identifies (1) the sequence of field actions to be directed in response to the effects of the fire?

(2) the actions to be directed once control is established at the Remote Shutdown Panel?

Sequence of Field Actions RSDP Actions A. Open RPS breakers CB2A and CB8B at Maintain reactor pressure 800-1 050 psig 1Y201A and 1Y201B with SRVs Close all HV-10603A(B)(C), RFP Override RCIC injection with reactor A(B)(C) DSCH ISO valves level off-scale high B. Close all HV-10603A(B)(C), RFP Lower reactor pressure 500-600 psig A(B)(C) DSCH ISO valves with SRVs Transfer both HS-54101A(B), MSIV Monitor operation of the Feedwater LOGIC A(B) POWER SUPPLY, to Startup Level control valve, HV-1 0641, EMERGENCY at 1C115 C. Open RPS breakers CB2A and CB8B at Maintain reactor pressure 800-1050 psig 1Y201A and 1Y201B with SRVs Transfer both HS-54101A(B), MSIV Reset RCIC high-level trip and maintain LOGIC A(B) POWER SUPPLY, to reactor level with RCIC EMERGENCY CONFIDENTIAL Examination Material Page 197 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION D. Close all HV-10603A(B)(C), RFP Stabilize reactor pressure 700-900 psig A(B)(C) DSCH ISO valves with SRVs Open RPS breakers CB2A and CB8B at Reset RCIC high-level trip and maintain 1Y201A and 1Y201 B reactor level with RCIC Proposed Answer A Applicant References None Explanation For a control room fire ON-100-109 specifies the action to take to mitigate the possible spurious operation of Control Room equipment. In the postulated scenario reactor pressure will be lowering due to the misoperation of the Main Turbine pressure regulator due to a fire-induced malfunction of the pressure regulator setpoint. While the ON allows deviation from the order of sections of the procedure, in this scenario such deviation is inappropriate due to the pressure reduction transient in progress.

The first action required to stop the uncontrolled reduction in reactor pressure is to close the MSIVs. OP-AD-055 Step 8.6.10.b addresses pressure control when EOPs are entered and allows operator action to terminate pressure reduction to maintain pressure> 800 psig.

E0-100-102 Step RC/P-1 requires action to prevent uncontrolled condensate injection before reactor pressure < 700 psi g. The method for accomplishing this per ON-1 00-009 is to close the RFP discharge isolation valves. However, this will take considerable time.

At the Remote Shutdown Panel action should be taken to stabilize the unit. MSIVs can be closed promptly, so control of reactor pressure will be required. A band of 700-900 psig prevents uncontrolled condensate injection while stabilizing pressure. Preventing RCIC injection with a high level signal present is prudent as RCIC F045 closure on +54" is defeated with transfer controlled to the RSDP (Caution at Step 4.6.4a of ON-1 00-009).

A Correct. This is the preferred sequence of events to respond to a fire-induced malfunction of turbine pressure control. The actions at the RSDP will stabilize reactor pressure, prevent uncontrolled condensate injection until the HV-10603 valves can be closed, and protect RCIC from damage due to operation with high reactor level.

B Incorrect. Attempting to close the RFP discharge valves before taking action to close the MSIVs would contradict the guidance of E0-100-102 to prevent uncontrolled condensate injection and stabilizing reactor pressure. A pressure band of 500-600 psig will allow uncontrolled condensate injection. Operation of the HV-10641 is irrelevant as the RFP discharge valves will not be fully closed for quite some time, allowing uncontrolled injection from condensate windmilling the RFPs.

C Incorrect. Action to prevent uncontrolled condensate injection . A pressure band of 800-1050 psig is acceptable. Reset of RCIC trips is possible at the RSDP with the RCIC Turbine trip/throttle valve. On a high level RCIC does not trip but experiences an automatic closure of the F045 steam supply valve. This is defeated when operating at the RSDP.

D Incorrect. This sequence does include action to prevent uncontrolled injection from Condensate, but transferring control to the RSDP before taking action to close the MSIVs does not reflect the preferred sequence specified by ON-100-009 and allows the reactor pressure reduction to continue for a longer duration.

10CFR55 43.5 This is an SRO-Ievel question as the priority for local action is required to be selected and the effects of the local actions are required to be evaluated to select the correct strategy at the RSDP. Detailed sequencing of activities by the SRO is required to ensure control of reactor pressure and level is promptly established.

Technical References ON-100-109 Section 3, 4.2-4.3 OP-AD-055 Step 8.5.6 Learning Objectives 15304 CONFIDENTIAL Examination Material Page 198 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION Question Source New Previous NRC Exam No Comments Operations Reviewer _ _I _ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 199 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION BLANK PAGE CONFIDENTIAL Examination Material Page 200 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION Exam I SRO I Tier I2 I Group I 2 I Cognitive Level I Low I Level of Difficulty I 2 KIA 234000 2.2.12 Fuel Handling Equipment I Importance 1 4.1 Statement Knowledge of surveillance procedures.

QUESTION 93 Refer to the information on the following page when answering this question.

Unit 1 is in a refueling outage. Preparations for in-vessel fuel movement are in progress.

The status of the Refuel Platform main hoist surveillances is as follows TS!TRM SR Procedure Title Satisfied Last Performed S0-181-001 Weekly Unit 1 Refueling Platform Grapple SR 3.9.1.1 August 14 at 1200 Operability S0-181-004 Outage Unit 1 Refueling Platform Grapple TRS 3.9.3.1 August 15 at 1200 Operability Initial core offload is scheduled to begin on August 22 at 1800.

Which one of the following identifies only those Refueling Platform surveillances that must be re-performed before in-vessel fuel movement can begin per the schedule, per NDAP-QA-0722, Surveillance Testing Program?

A. No surveillances are required to be re-performed B. Perform S0-181-001, ONLY C. Perform S0-181-004, ONLY D. Perform S0-181-001 AND S0-181-004 CONFIDENTIAL Examination Material Page 201 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION SURVEILLANCE FREQUENCY SR 3.9.1 .1 Perform CHANNEL FUNCTIONAL TEST on each of 7 days the following required refueling equipment interlock inputs:

a. All rods in,

b. Refuel platform position,

c. Refuel platform fuel grapple, fuel loaded,

d. Refuel platform frame mounted hoist, fuel loaded,

e. Refuel platform monorail mounted hoist, fuel loaded.

TRS 3.9.3.1 Demonstrate the refueling platform main hoist used for Within 7 days prior to handling of control rods or fuel assemblies within the the start of such reactor pressure vessel to be OPERABLE operations Proposed Answer D Applicant References None Explanation The applicant is required to identify whether Refueling Platform surveillances are current prior to initial in-vessel fuel movement activities. The applicant must apply SR applicability guidance in TS SR 3.0.2 and TRM TRS 3.0.2.

S0-181-001 is the SO used to satisfy the requirements of TS SR 3.9.1.1 . The SO will have been last performed 8.25 days ago at the scheduled time for fuel movement. The TS SR 3.0.2 grace of 1.25 times the SR frequency applies (8.75 days), so the SO is not required to be performed again until 0600 on August 23 if the grace is to be applied. NDAP-QA-0722 states that the station expectation is that all routine surveillance activities will be performed without reliance on the use of grace. As S0-181-004 will have to be performed, deferring performance of S0-181-001 to use the grace would contradict the expectation set by the procedure.

S0-181-004 is the SO used to satisfy the requirements of TRM TRS 3.9.3.1. The SO will have been last performed 7.25 days ago at the scheduled time for fuel movement. TRM TRS 3.0.2 does not allow application of a grace period for TRS with a frequency of "once", which is true of TRS 3.9.3.1 .

A Incorrect. Both surveillances must be re-performed prior to fuel movement.

B Incorrect. Both surveillances must be re-performed prior to fuel movement.

C Incorrect. Both surveillances must be re-performed prior to fuel movement.

D Correct. Both surveillances must be re-performed prior to fuel movement to satisfy TS/TRM and the station expectation set forth in NDAP-QA-0722 Step 7.1.6.b.

10CFR55 43.2 This is an SRO-Ievel question because application of generic LCO requirements (SR 3.0.2) is required.

Technical References TS SR 3.0.2 TRM TRS 3.0.2 TS 3.9.1 TRM 3.9.3 NDAP-QA-0722 Step 7.1 .6.b Learning Objectives 13386 Question Source New Previous NRC Exam No Comments CONFIDENTIAL Examination Material Page 202 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION Operations Reviewer mj I 06126114 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 203 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION BLANK PAGE CONFIDENTIAL Examination Material Page 204 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION Exam I SRO I Tier I 3 I Group I N/A I Cognitive Level I Low I Level of Difficulty I 3 KJA 2.1.34 Conduct of Operations I Importance 1 3.5 Statement Knowledge of primary and secondary plant chemistry limits.

QUESTION 94 Use your provided references when answering this question.

Unit 1 is operating at 20 percent power when Chemistry reports the following reactor coolant parameters to the Control Room .

Conductivity 11 1-fmho/cm Chlorides 0.300 ppm pH 8.8 After 6 hours6.944444e-5 days <br />0.00167 hours <br />9.920635e-6 weeks <br />2.283e-6 months <br />, reactor power has been lowered and Mode 2 has been entered . The following reactor coolant parameters are reported:

Conductivity 0.9 IJmhos/cm Chlorides 0.150 ppm pH 6.5 Which one of the following describes the actions to be taken?

A. Restore chlorides to within limits in the next 66 hours7.638889e-4 days <br />0.0183 hours <br />1.09127e-4 weeks <br />2.5113e-5 months <br /> Verify the cumulative time exceeding the limit is :S 336 hours0.00389 days <br />0.0933 hours <br />5.555556e-4 weeks <br />1.27848e-4 months <br /> in the past year B. Restore chlorides to within limits in the next 48 hours5.555556e-4 days <br />0.0133 hours <br />7.936508e-5 weeks <br />1.8264e-5 months <br /> OR Be in Mode 3 in the following 12 hours1.388889e-4 days <br />0.00333 hours <br />1.984127e-5 weeks <br />4.566e-6 months <br /> AND Mode 4 in the following 36 hours4.166667e-4 days <br />0.01 hours <br />5.952381e-5 weeks <br />1.3698e-5 months <br /> C. Be in Mode 3 in the next 12 hours1.388889e-4 days <br />0.00333 hours <br />1.984127e-5 weeks <br />4.566e-6 months <br /> AND in Mode 4 in the next 36 hours4.166667e-4 days <br />0.01 hours <br />5.952381e-5 weeks <br />1.3698e-5 months <br /> D. Be in Mode 3 in the next 6 hours6.944444e-5 days <br />0.00167 hours <br />9.920635e-6 weeks <br />2.283e-6 months <br /> AND in Mode 4 in the next 30 hours3.472222e-4 days <br />0.00833 hours <br />4.960317e-5 weeks <br />1.1415e-5 months <br /> Proposed Answer D Applicant References TRM 3.4.1 Explanation Initially pH, conductivity, chloride levels are all out of specification per TRM 3.4.1. With conductivity above 10 J.1mho/cm Condition B is not applicable and ConditionE is applicable.

The Note on Condition E requires completion of the Required Actions once the condition is entered. Therefore Unit 1 must be in Mode 3 within 12 hours1.388889e-4 days <br />0.00333 hours <br />1.984127e-5 weeks <br />4.566e-6 months <br /> of the initial chemistry excursion and in Mode 4 within 36 hours4.166667e-4 days <br />0.01 hours <br />5.952381e-5 weeks <br />1.3698e-5 months <br /> of the initial excursion.

A Incorrect. This reflects application of Condition B for conductivity and chlorides, which is not allowed, and Condition C for pH.

B Incorrect. This reflects application of Condition F for Mode 2 operations. As Condition E was entered its Required Actions are more limiting.

C Incorrect. This reflects application of Condition E at the current time, not for 6 hours6.944444e-5 days <br />0.00167 hours <br />9.920635e-6 weeks <br />2.283e-6 months <br /> previous.

CONFIDENTIAL Examination Material Page 205 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION D Correct. This is the correct application of Condition E Required Actions and Completion Times.

10CFR55 43.2 This is an SRO-Ievel question as it requires application of Required Actions and Completion Times.

Technical References TRM 3.4.1 Learning Objectives Question Source Bank Previous NRC Exam Yes LOC23 Comments Operations Reviewer _ _I _ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 206 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION Exam I SRO I Tier I3 I Group I NIA I Cognitive Level I Low I Level of Difficulty I 3 KIA 2.2.23 Equipment Control I Importance 14.6 Statement Ability to track Technical Specification limiting conditions for operations.

QUESTION 95 Which one of the following identifies a condition where application of the Maximum Out Of Service Time is required by NDAP-QA-0312, Control of LCOs, TROs, and Safety Function Determination Program?

A. A TS support system is inoperable and supports two or more TS supported systems B. A TS supported system is inoperable due to two or more support system inoperabilities C. An LCO does not allow separate condition entry and a second required system becomes inoperable after the LCO has already been entered D. A surveillance performed utilizing the Allowed Performance Time of a LCO results in declaring a system required by the LCO inoperable Proposed Answer B Applicant References None Explanation The MOST is defined in NDAP-QA-0312 for each TS supported system to ensure supported system LCO Allowed Outage Times (AOTs) are not exceeded due to multiple support system inoperabilities. The MOST is calculated by combining the limiting AOTs for the support system(s) with the limiting AOT for the supported system.

A Incorrect. No concern for exceeding supported system AOTs exists when only 1 TS support system is inoperable.

B Correct. The instance of 2 or more support system inoperabilities requires tracking MOST for the supported system per NDAP-QA-0312 Step 6.3.5.

C Incorrect. This is a plausible distractor in that it is a description of when application of Completion Time extension is allowed by TS 1.3.

D Incorrect. This describes a condition where some additional action with regard to the AOT is plausible, but it is not related to MOST.

10CFR55 43.2 This question is SRO-Ievel in that it requires knowledge of generic TS bases to analyze TS required actions (application of MOST).

Technical References NDAP-QA-0312 Learning Objectives 14635 Question Source Bank ILO LXR AD0441146201005 Previous NRC Exam No Comments Operations Reviewer _ _I_ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 207 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION BLANK PAGE CONFIDENTIAL Exam ination Material Page 208 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION Exam I SRO I Tier I3 I Group I N/A I Cognitive Level I High I Level of Difficulty I 2 KJA 2.3.14 Radiation Control jlmportance 1 3.8 Statement Knowledge of radiation or contamination hazards that may arise during normal, abnormal, or emergency conditions or activities.

QUESTION 96 Unit 1 is in a refueling outage. Core shuffle is in progress.

A re-channeled irradiated fuel assembly is located in the Fuel Prep Machine at the full-up position for channel fastener installation.

An inadvertent drain path from the reactor to the Suppression Pool is created.

Reactor cavity level lowers rapidly.

The 818' refuel floor is evacuated due to dose rates before the fuel assembly in the prep machine can be lowered.

Initial attempts to secure the leak or makeup to the reactor fail.

Which one of the following describes the initial Emergency Classification for this event, and the basis for the declaration?

Classification EAL A. Unusual Event CU4 Loss or potential loss of the integrity of the Reactor Coolant System fission product barrier represents a potential degradation of the level of safety of the plant B. Alert CA5 Loss of RCS inventory will result in a potential loss of decay heat removal and fuel clad damage C. Alert RA3 Loss of spent fuel pool inventory will result in unexpected increases in radiation dose rates within plant buildings, and may be a precursor to a radioactivity release to the environment D. Site Area CS5 Loss of RCS inventory will result in a loss or potential loss Emergency of two fission product barriers (fuel clad, RCS)

Proposed Answer c Applicant References EP-RM-004 Table R, Table C Explanation The event described is an inadvertent loss of RCS and SFP inventory resulting in lowering level in the combined SFP/reactor cavity. EALs from both Table C, for the reactor, and Table R, for the SFP, apply. The event is complicated by the presence of an irradiated fuel assembly in the Fuel Prep Machine which will be uncovered well in advance of the other fuel in the SFP or reactor.

CONFIDENTIAL Examination Material Page 209 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION A Incorrect. Alert conditions have been met in RA3. While the coolant inventory loss may have been assumed to exceed the CU4 criteria, this EAL does not apply in Mode 5.

B Incorrect. Reactor level has not lowered to the ECCS initiation setpoint and nothing implying a loss of reactor level indication is specified in the stem.

C Correct. SFP water level will be< 22ft above the seated irradiated fuel in the SFP and uncovery of the fuel bundle in the prep machine should be assumed as no action to mitigate the draindown has yet been successful.

D Incorrect. CS5 would be the upgrade path in the reactor draindown event continues, but conditions for declaration of this EAL are not yet met as level is not specified and nothing implying a loss of reactor level indication is specified in the stem.

10CFR55 43.4 This is an SRO-Ievel question as an EAL declaration is required to be made.

Techn ical References EP-RM-004 Learning Objectives 14594, 15549 Question Source New Previous NRC Exam No Comments Operations Reviewer mj I 0610312014 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 210 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION Exam Cognitive Level KIA 2.4.23 Emergency Procedures I Plan 4.4 Statement Knowledge of the bases for prioritizing emergency procedure implementation during emergency operations.

QUESTION 97 Unit 2 was operating at rated power when a small reactor coolant system leak developed in the Drywell.

Scram Imminent actions were performed and the reactor was manually scrammed.

Multiple control rods failed to insert. Immediate operator actions for an ATWS were performed .

The following conditions were reported during the scram report:

Reactor level +25", steady Reactor pressure 950 psig , steady Drywell pressure 3 psig, up slow Suppression Pool temperature 95 °F, up fast Initial ATWS power was recorded as 35 percent.

l Which one of the following identifies (1) the direction to be provided first when implementing E0-200-113, Power/Level Control , for these conditions?

(2) why the action is to be performed first?

First direction Why performed first A. Inject SLC per OP-253-001 , SLC Stop or prevent large-magnitude limit-System cycle power oscillations B. Inhibit ADS per OP-283-001 , Automatic Prevent a reactor power excursion due Depressurization System and SRVs to cold-water injection C. Lower reactor water level to -60" Immediate and rapid reduction in core to -11 0" per OP-245-005, Infrequent power Manual RFP Operations D. Open SRVs to lower reactor pressure to Stop power oscillations due to reactor 945 psig per OP-283-001 , Automatic level swings, as SRVs open and close Depressurization System and SRVs Proposed Answer A Applicant References None CONFIDENTIAL Examination Material Page 211 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION Explanation The stem describes a high-power ATWS in progress. Only immediate operator actions have been performed. E0-200-113 has been performed to the point of recording the initial ATWS power. The four choices represent valid initial directions in each of the power, level and pressure legs for a high-power A TWS. Injection of SLC is the first priority, however, as that will be most effective in reducing power and terminating the ATWS event.

A Correct. Per E0-200-113 Step LQ/Q-3, If initial ATWS power was greater than 5%, then a relatively large number of control rods have failed to insert. The seriousness of this condition requires immediate injection of boron to positively terminate the ATWS event.

B Incorrect. Inhibiting ADS is not immediately required as conditions for automatic ADS initiation are not present. Preventing future ADS operation is required, but injection of SLC is the priority per LQ/Q-3.

C Incorrect. While OP-245-005 Att B contains the directives to lower power through tripping recirc pumps and lowering level, the initial goal of the level reduction is to promptly establish conditions to preclude development of severe power/flow instabilities.

D Incorrect. Reactor pressure is being maintained steady by Turbine EHC. Reactor pressure steady implies that cyclic SRV operation is not occurring. No action to lower pressure is therefore required by LQ/P-3.

10CFR55 43.5 This is an SRO-Ievel questions as an assessment of plant conditions is required to identify a high-power ATWS in progress with no mitigating action taken, and selection of the highest-priority action among applicable EOP pathways to implement in response.

Technical References E0-000-113 Learning Objectives 14622 Question Source New Previous NRC Exam No Comments Operations Reviewer _ _/_ _ __ Facility Representative _ _/_ _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 212 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION Exam I SRO I Tier I3 I Group I N/A I Cognitive Level I High I Level of Difficulty I 3 KJA 2.2.19 Equipment Control I Importance 1 3.4 Statement Knowledge of maintenance work order requirements.

QUESTION 98 Unit 1 is operating at rated power.

Standby Gas Treatment Fan OV1 098 fails during a surveillance test. The fan motor must be replaced.

Which one of the following identifies the appropriate component Criticality Code and Priority of the WO to repair the motor for SBGT Fan B, per NDAP-QA-1901?

A. High Critical WO Priority 1 B. Critical WO Priority 2 C. Critical WO Priority 3 D. Non-Critical WO Priority 3 Proposed Answer B Applicant References None Explanation NDAP-QA-1901 Step 5.2 provides the definitions of critical and non-critical components.

Component criticality is a key input to NDAP-QA-1901 Att B for properly selecting only those Priority 1 WO that need to bypass the normal scheduling process and may be directed to work around the clock by the Shift Manager. The SRO has the responsibility of determining if maintenance is a Priority 1 condition per Att B.

A Incorrect. Loss of a SBGT train does not require an immediate scram, loss of an entire safety system (i.e., safety function) or entry into a LCO shutdown statement. TS 3.6.4.3 allows 7 days for the restoration of the train.

B Correct. Loss of the SBGT B fan only renders 1 division of SBGT inoperable and requires entry into a 7-day LCO in TS 3.6.4.3.

C Incorrect. Priority 3 WO are associated with operable SSCs or Non-Critical components.

D Incorrect. SBGT is critical and should be worked as Pri 2.

10CFR55 43.5 This is an SRO-Ievel question as the knowledge tested is required to correctly determine maintenance WO prioritization and the procedure processes required to be followed to implement the WO.

Technical References NDAP-QA-1901 Step 5.2, Att B TS 3.6.4.3 Learning Objectives 15268 Question Source Modified Bank Adapted toSSES from GGNS 2010-06-FINAL CONFIDENTIAL Examination Material Page 213 of 218

I .

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION Previous NRC Exam Yes Comments Operations Reviewer mj I 06103114 Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 214 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION Exam I SRO I Tier I3 I Group I N/A I Cognitive Level I High I Level of Difficulty I 2 KIA 2.4.32 Emergency Procedures I Plan I Importance J 4.0 Statement Knowledge of operator response to loss of all annunciators.

QUESTION 99 Use your provided references when answering this question.

I&C is performing annual testing of Diesel Generator A fire detection (Fire Zone 0-41A) per their surveillance instruction.

The technician reports all Control Room Simplex panel annunciation for the Diesel Generator A room failed to respond .

The technician confirms that the local Simplex panel functioned properly.

Which one of the following describes ALL of the Technical Specification Required Actions to be taken in response to this failure?

A. Enter TRO 3.7.3.8 Condition B, Required Actions Band 8.2.1 B. Enter TRO 3.7.3.2 Condition A, Required Action A and Condition B, required Action 8.1 C. Enter TRO 3.7.3.8 Condition B, Required Actions 8 and 8 .2.1 Enter TRO 3.7.3.2 Condition A, Required Action A and Condition B, required Action 8.1 D. Enter TRO 3.7.3.8 Condition 8, Required Actions Band 8.2.1 Enter TRO 3.7.3.2 Condition A, Required Action A and Condition C, required Action C.1 Proposed Answer A Applicant References TRM 3.7.3.2, TRM 3.7.3.8 Explanation A loss of Control Room annunciation for fire detection and suppression in the DG A room has been detected. The procedures for responding to this condition is 01-AD-013. TRM 3.7.3.8 is applicable and requires an hourly firewatch to monitor the local Simplex alarm panel. A NOTE in Section 1.0 of 01-AD-013 states that DG fire suppression (preaction sprinklers required by TRM 3.7.3.2) remain OPERABLE with a loss of Control Room Simplex alarm functionality.

A Correct. This is the only applicable TRM LCO not satisfied.

B Incorrect. The fire suppression systems in the DG A room remain operable. Entry into TRM 3.7.3.8 for inoperable fire detection annunciation is also required.

C Incorrect. Entry into TRM 3.7.3.2 is not required.

D Incorrect. Entry into TRM 3.7.3.2 is not required.

10CFR55 43.5 This is an SRO-Ievel question as the determination of TS Condition entry and identification of Required Actions is required.

Technical References 01-AD-013, TRM 3.7.3.8, TRM 3.7.3.2 Learning Objectives 13030 CONFIDENTIAL Examination Material Page 215 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION Question Source New Previous NRC Exam No Comments Operations Reviewer _ _I _ __ Facility Representative _ _I _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 216 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION Exam I SRO I Tier I3 I Group I N/A I Cognitive Level l Low JLevel of Difficulty I 2 KJA 2.3.6 Radiation Control I Importance 1 3.8 Statement Knowledge of radiation exposure limits under normal or emergency conditions.

QUESTION 100 An accident has occurred on Unit 1.

NERO has been activated and all facilities are operational.

The Control Room reports that total site vent stack rad monitor readings for noble gas have risen to 7.3E+9 IJCi/hr.

The first calculation of offsite doses rates at the EPB is finalized in the TSC with the following results:

TEDE 600 mR Child thyroid CDE 2000 mR Which one of the following identifies (1) the classification of this event?

(2) the EAL Threshold Value exceeded as the basis for the declaration?

Classification EAL Threshold A Site Area Emergency RS1, 1 B. Site Area Emergency RS1, 2 C. General Emergency RG1, 1 D. General Emergency RG1, 2 Proposed Answer B Applicant References EP-RM-004 Att R Explanation Due to radioactive release from an unspecified accident on Unit 1, the site release rate has exceeded the RG1 EAL Threshold 1 limit. However, the note to the EAL Thresholds in RG1 and RS1 indicates that the declaration should be based on actual offsite dose calculations instead of release rates. In this instance, an offsite dose calculation is available that shows projected doses below the GE threshold, but above the RS1 EAL Threshold 2 for a SAE declaration.

A Incorrect. While a SAE should be declared, the declaration is based on exceeded Threshold 2 for offsite dose calculation using actual meteorology.

B Correct. A declaration of a SAE on exceeding RS1 Threshold 2 is correct.

CONFIDENTIAL Examination Material Page 217 of 218

SUSQUEHANNA STEAM ELECTRIC STATION LOC26 NRC INITIAL LICENSE EXAMINATION SENIOR REACTOR OPERATOR WRITTEN EXAMINATION C Incorrect. AGE should not be declared on RG1 Threshold 1 due to the note, which specifies that the classification should be based on offsite dose calculation if available.

In this case the offsite dose calculation is available and shows that offsite dose has not risen to the GE level. Declaration of a GE is not a conservative action and should only be made when specific EAL Thresholds are exceeded.

D Incorrect. Declaration of a GE is unwarranted on Threshold 2, as the limit is not exceeded .

10CFR55 43.4 Technical References EP-RM-004 Att R Learning Objectives 14594, 15549 Question Source New Previous NRC Exam No Comments Operations Reviewer _ _I _ __ Facility Representative _ _I_ _ __

lnit I date lnit I date CONFIDENTIAL Examination Material Page 218 of 218

• • **

• r L _j Course#:

Course:

First Name:

---

2~~~~

K.E j . -------------- LastName: --------------------------------

Test Number:

-- Employee Identifier I have read the Student Instructions on the Exam Cover Sheet prior to taking Exam Identifier the exam and understand my responsibility in regards to exam security and integrity.

- <D<D<D<D<DCD CD<D<D<D<D<D<DCD

- mmmmmm Examinee Signature -------------------------- Date __________ mmmmmmmm

- Q)Q)Q)Q)Q)(]) (])G)G)G)G)(])(])(])

- CDCDCDCDCDCD I have had the opportunity to review the exam questions and correct CDCDCDCDCDCDCDCD

- answers following the completion of the exam with the instructor to ensure my understanding.

- (j)(j)(j)(j)(j)U) U)(j)(j)(j)(j)(j)(j)(j)

- Examinee Signature -------------------------- Date __________

--- 1.

2.

© .

© .

21.

22 .

• © 41.

42.

s1.

62.

• oo©

© .

81. ©

82. e ©

3. © 23. 43. © . 63. 83. ©

4. * © 24. . © 44. e © 64. © . 84. e

5. © e 25. e 45. 65. © 85. ©

--- 6.

7. * © 2s.

27.

© e

© 46.

47.

© .

e 66.

67.

© .

©

86. ' V ©

87.

8. * © 28. . © 48. . © 68. 88. ©

9. © 29. © . 49 . * © sg. e oo© 89. ©

-- 10. © . 30. . 50. * © 10. e © 90. © e

11. e © 31. e 51. © . 71. . © 91. j)@

12. 32. . © 52. © 12. e © 92 . * ©

13. . 33. e oo© 53. . © 73. (jj 93. ©

14. * © 34. © e 54. © . 74. . 94. © e

15. © 35. * © 55.

• oo© 75. © e 95. ©

16. © . 36. . 56. * © 76. © . 96.

11. © e 37. © . 57. © 77. ot!J 97. ©

18. © 38. © . 58. © . 78. . 0~(, 98. ©

19. e © 39. e © 59. . 79. <4)© e 99. ©

20. 4o. e © 60. . © 80. 01- ~ 100. © 5 r A N - R0 \ OpScan iNSIGHT'M EM-293648-1 :654321