ML011130220
| ML011130220 | |
| Person / Time | |
|---|---|
| Site: | Watts Bar  |
| Issue date: | 09/13/2000 |
| From: | NRC/RGN-II |
| To: | |
| References | |
| -RFPFR, 50-390/01301, 50-391/01301 | |
| Download: ML011130220 (226) | |
See also: IR 05000390/2001301
Text
/
FINAL SUBMITTAL
WATTS BAR EXAM
50-390, 391/2001-301
JANUARY 29 - FEBRUARY 6,
2001
FINAL AS-GIVEN JPMs FOR EACH
WALK-THROUGH TEST
4r
JPMR023/Sim
Page 1 of 14
REGION II
INITIAL LICENSE EXAMINATION
B.l.b JPMR023ISim
RESPOND TO PRESSURIZER HIGH LEVEL PER FR-I.1
APPLICANT
EXAMINER
JPMR023/Sim
Page 2 of 14
REGION !1
INITIAL LICENSE EXAMINATION
Task: RESPOND TO PRESSURIZER HIGH LEVEL PER FR-I.1
Alternate Path: 1-FCV-62-69 will not open requiring the performer to use RNO and establish
excess letdown.
Facility JPM #: 3-OT-JPMR023 Rev 1
KIA Rating(s): 011A1.01 (3.5/3.6) 011A1.02 (3.3/3.5) 2.1.23 (3.9/4.0)
2.1.31 (4.2/3.9) 006A4.09 (4.1/4.2)
Task Standard: Performance of FR-I.1 which results in Excess Letdown being placed in service.
Preferred Evaluation Location: Preferred Evaluation Method:
Simulator X In-Plant Perform X Simulate
References: FR-I.1 "High Pressurizer Level" Rev. 6
Task Number:: RO-113-FRI.1-001 APPLICABLE FOR: RO/SRO
IOCFR55.45: 6
Validation Time: 17 min. Time Critical: No
Applicant: Time Start:
NAME SSN Time Finish:
Performance Rating: SAT UNSAT Performance Time
Examiner: /
NAME SIGNATURE DATE
COMMENTS
JPMR023/Sim
Page 3 of 14
SIMULATOR OPERATOR INSTRUCTIONS:
1. Initialize to IC # 145.
2. Acknowledge all alarms.
3. Ensure 1-FCV-62-69 has been over ridden to the close position.
View on ORS summary.
4. Ensure Source Range Count Rate is audible in horse shoe.
5. Freeze simulator until the performance indicates understanding of the task and time
is allowed for control board familiarization.
6. NOTE: This JPM has been preshot in IC #145. The following is the setup instructions
if needed:
Reset to IC #40
Manually initiate Reactor Trip and SI.
Allow to run until PZR level is = 94%.
Terminate SI
Establish Charging at minimum flow.
Reset 0 A isolation signal.
Transfer Steam Dumps to pressure mode and stabilize RCS temperature.
Re-establish Letdown per ES-I.1.
Ensure Letdown Valve 1-FCV-62-77 is closed.
Insert ior zdihs6269a close to override valve hand switch to close position..
Acknowledge all alarms.
FREEZE the simulator till the performer indicates an understanding of the task.
7. After performer indicates understanding of task, place simulator in run.
SIMULATOR OPERATOR INSTRUCTIONS:
ENSURE 1-FCV-62-69 has been over ridden closed.
(view override summary for zdihs6269a close)
JPMR023/Sim
Page 4 of 14
ToolslEquipment/Procedures Needed:
Ensure clean copy of FR-I.1 in all copies of Operating Instructions on the Simulator
Floor.
READ TO OPERATOR
DIRECTION TO TRAINEE:
I will explain the initial conditions, and state the task to be performed. All control
room steps shall be performed for this JPM, including any required
communications. I will provide initiating cues and reports on other actions when
directed by you. Ensure you indicate to me when you understand your assigned
task. To indicate that you have completed your assigned task return the handout
sheet I provided you.
INITIAL CONDITIONS:
An Inadvertent Safety Injection has occurred.
SI has been terminated and ECCS Pumps stopped.
While performing Step 19 of ES-I.1, the STA has determined there is a Yellow
Condition on the Inventory Status Tree due to the high Pressurizer level.
You are the OAC.
INITIATING CUES:
You have been directed by the Unit Supervisor to perform the appropriate
procedure for a Yellow Condition on Status Tree INVENTORY.
You are to notify the Unit Supervisor when the procedure has been completed.
JPMR023/Sim
Page 5 of 14
START TIME:
I
STEP 1: Obtain the correct procedure.
STANDARD: A copy of FR-I.1 has been obtained.
EXAMINER'S CUE: After the performer has demonstratedthe method of
obtaining the correct instruction,the evaluatorcan UNSAT
provide a copy of the instruction.
COMMENTS:
I-
STEP 2: [Step 1] CHECK SI terminated:
"* Both SI pumps STOPPED.
"* BIT isolated. SAT
STANDARD: Performer verifies Sl pumps stopped:
e1A-A SI Pump (green indicating lights on 1-HS-63-10A)
and:
Performer verifies BIT outlet valves are closed:
e1-FCV-63-25 (green indicating lights on 1-HS-63-25A)
e1-FCV-63-26 (green indicating lights on 1-HS-63-26A)
COMMENTS:
"**Italicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMR023/Sim
Page 6 of 14
STEP 3: [STEP 2] ENSURE cntmt air in service:
a. Aux air press greater than 75 psig [M-15]
b. Cntmt air supply valves OPEN [M-1 5]: SAT
"* 1-FCV-32-80.
"* 1-FCV-32-102.
- 1-FCV-32-110.
UNSAT
STANDARD: a. The performer verifies aux air pressure > 75 psig both
trains using 1-PI-32-104A & 1-PI-32-105A on M-15.
b. Valves listed are determined to be open by red indicating
lights LIT on M-15:
- 1-HS-32-80A,
- 1-HS-32-102A
- 1-HS-32-11OA
- CUE: If contacted, all air compressors are operating properly
COMMENTS:
i
CAUTION: During RCS solid water operation, any change in charging or
letdown flows could cause rapid RCS pressure changes.
STEP 4: [STEP 3] CHECK at least one charging pump RUNNING.
STANDARD: 1-HS-62-108A CCP IA-A has a red light verified to be
illuminated or amps on meter above handswitch. SAT
COMMENTS: UNSAT
"**ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMR023/Sim
Page 7 of 14
STEP 5: [STEP 4] CHECK charging flow established.
STANDARD: *Charging Flow Indicator, 1-FI-62-93A, indicating flow.
- 1-FVC-62-90 (verified open by red lights on handswitch)
- 1-FCV-62-91 (verified open by red lights on handswitch). SAT
- 1-FCV-62-85 (verified open by red lights on handswitch).
- 1-FCV-62-89 is throttled open to establish flow through the
Regen. Heat Exchanger.
UNSAT
COMMENTS:
Note To Evaluator: Step 6 will drive the performer to the RNO --
I
column. Step 7 is the RNO and the performer will NOT be able
to complete the RNO due to 1-FCV-62-69 failing to open.
I1_____________________________
STEP 6: [STEP 5] CHECK letdown in service.
STANDARD: Letdown is determined to NOT be in service by letdown flow
indicator, 1-FI-62-82, indicating no flow and letdown valves SAT
closed.
COMMENTS:
UNSAT
I _____________________________________________________
- Italicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMR023/Sim
Page 8 of 14
STEP 7: [STEP 5 RNO] IF charging flow established, THEN
ESTABLISH letdown:
a. OPEN letdown isolation valves.
- 1- FCV-62-69 SAT
9 1- FCV-62-70
- 1- FCV-62-77
STANDARD: Performer attempts to open 1-FCV-62-69 and determines the UNSAT
valve remains closed and cannot be opened by green light on
1-HS-62-69A.
- CUE: If contacted, acknowledge the request to open valve
locally. Report back that the valve will not open locally.
NOTE TO EVALUATOR: May perform other steps of RNO, however
letdown flow will not be established.
COMMENTS:
Note To Evaluator: Step 8 will drive the performer to the RNO
column. Steps 8 through 14 are all part of this same
instruction step (8 - 13 is the RNO).
4-
STEP 8: [STEP 6] CHECK Charging and letdown flows established.
STANDARD: Performer determines that normal letdown is NOT
established and proceeds to the RNO, excess letdown is SAT
required due to normal letdown being isolated and proceeds to
the RNO column of the instruction.
UNSAT
COMMENTS:
- ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMR023/Sim
Page 9 of 14
STEP 9: [STEP 6 RNO] PLACE excess letdown in service: CRITICAL
a. OPEN 1- FCV-70-143 STEP
b. OPEN 1- FCV-70-85.
STANDARD: 1-HS-70-143A has been placed in the OPEN position. SAT
1-HS-70-85A has been placed and held in the OPEN position
until the valve gets full open.
Step is critical to establish cooling through excess UNSAT
letdown heat exchanger.
COMMENTS:
I
STEP 10: [STEP 6 RNO]
c. OPEN 1- FCV-62-54. CRITICAL
d. OPEN 1- FCV-62-55. STEP
STANDARD: 1-HS-62-54A has been placed in the OPEN position.
1-HS-62-55A has been placed in the OPEN position.
UNSAT
Step is critical to establish cooling through excess
letdown heat exchanger.
COMMENTS:
"**ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMR023/Sim
Page 10 of 14
STEP 11: [STEP 6 RNO]
e. ENSURE 1-FCV-62-59 in NORMAL.
STANDARD: 1-HS-62-59A has been checked/placed in the normal position.
COMMENTS:
UNSAT
STEP 12: [STEP 6 RNO]
f. ADJUST 1-FCV-62-56 to maintain excess letdown heat CRITICAL
exchanger outlet temp less than 225 0 F. STEP
STANDARD: 1-H IC-62-56A pot is rotated counter clockwise to open and
temperature is maintained <225°F on 1-TI-62-58 on 1-M-5. SAT
Step is critical to prevent excess thermal stress to the
excess letdown heat exchanger.
UNSAT
NOTE TO EVALUATOR: If ARI is referenced, performer may limit
temperature to less than 2000 F.
COMMENTS:
Note To Evaluator: Steps 13 and 14 are part of the same instruction
step.
i
STEP 13: [STEP 7] CHECK RCS press:
a. Pressure less than 2335 psig.
STANDARD: RCS pressure verified to be < 2335 psig by observation of
RCS pressure instruments on the MCR.
COMMENTS: UNSAT
- Italicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMR023/Sim
Page 11 of 14
STEP 14: [STEP 7] CHECK RCS press:
b. Pressure less than 2260 psig.
STANDARD: RCS pressure verified to be < 2260 psig by observation of
RCS pressure instruments on the MCR.
COMMENTS: UNSAT
STEP 15: [STEP 8] CHECK PZR PORVs CLOSED.
STANDARD: Both PORV Handswitches have been located and checked SAT
closed by green lights lit on 1-HS-68-340AA & 1-HS-68-334A.
COMMENTS:
UNSAT
STEP 16: [STEP 9] CONTROL pzr heaters as necessary to establish
pzr bubble.
STANDARD: Control Bank "D" and "A-A", "B-B" Backup Heaters may be
manually energized. "C" Backup heaters are observed to be
energized due to high level in pressurizer.
UNSAT
COMMENTS:
"**ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMR023/Sim
Page 12 of 14
- - . - -- - - 1
Note I o Evaluator: Steps 17 and 18 are part of the same instruction
step.
STEP 17: [STEP 10] ENSURE PZR spray valves CLOSED.
a. CHECK normal pzr spray valves closed. SAT
STANDARD: 1-XI-68-340B & 1-XI-68-340D are checked to indicate red
lights off & green lights on.
UNSAT
NOTE TO EVALUATOR: Spray valves may be slightly open due to
integral operation.
COMMENTS:
I
STEP 18: [STEP 10] b. ENSURE aux spray valve CLOSED.
STANDARD: 1-FCV-62-84 is checked closed by green light illuminated on
1-HS-62-84A
UNSAT
COMMENTS:
+
STEP 19: [STEP 11] CONTROL charging and letdown:
a. MAINTAIN RCS pressure stable. SAT
b. DECREASE pzr level.
STANDARD: 1. PZR pressure is being maintained in its normal range by
observation of RCS pressure instruments in the MCR. UNSAT
2. PZR Level is decreasing.
COMMENTS:
I
"**Italicized Cues Are To Be Used Only If JPM Performanceis Being Simulated.
JPMR023/Sim
Page 13 of 14
STEP 20: [STEP 12] CHECK pzr Level < 92%
STANDARD: PZR Level is decreasing. If pressurizer level is _>92% then
performer returns to Step 11 of FR-I. 1 (the previous
performance step). UNSAT
- CUE: If pressurizer level is decreasing, state that pressurizer
level is now 90%
COMMENTS:
I1
STEP 21: [STEP 13] RETURN TO instruction in effect.
STANDARD: The Unit Supervisor has been notified that FR-I.1 has been
completed and to return to the instruction in effect.
UNSAT
- EXAMINER CUE: When notified, acknowledge the report)
COMMENTS:
END OF TASK
_________________________________
I1
TIME STOP:
- Italicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Page 14 of 14
APPLICANT CUE SHEET
(TO BE RETURNED TO EXAMINER UPON COMPLETION OF TASK)
DIRECTION TO TRAINEE:
I will explain the initial conditions, and state the task to be performed. All control
room steps shall be performed for this JPM, including any required
communications. I will provide initiating cues and reports on other actions when
directed by you. Ensure you indicate to me when you understand your assigned
task. To indicate that you have completed your assigned task return the handout
sheet I provided you.
INITIAL CONDITIONS:
An Inadvertent Safety Injection has occurred.
SI has been terminated and ECCS Pumps stopped.
While performing Step 19 of ES-1.1, the STA has determined there is a Yellow
Condition on the Inventory Status Tree due to the high Pressurizer level.
You are the OAC.
INITIATING CUES:
You have been directed by the Unit Supervisor to perform the appropriate
procedure for a Yellow Condition on Status Tree INVENTORY.
You are to notify the Unit Supervisor when the procedure has been completed.
JPMR055/Sim
Page 1 of 10
REGION il
INITIAL LICENSE EXAMINATION
B.l.c JPMR055/Sim
PERFORM ADDING N2 TO COLD LEG
ACUMULATORS WHILE IN SERVICE PER SOI-63.01
APPLICANT
EXAMINER
JPMR055/Sim
Page 2 of 10
REGION 11
INITIAL LICENSE EXAMINATION
Task: PERFORM ADDING N2 TO COLD LEG ACUMULATORS WHILE IN SERVICE PER SOI-63.01
Alternate Path: N/A
Facility JPM #: 3-OT-JPMR055 Rev 0
K/A Rating(s): 006A1.13 (3.5/3.7) 2.1.23 (3.9/4.0) 2.1.30 (3.9/3.4)
Task Standard: Cold Leg Accumulator 1 pressure is with-in alarm limits, and normal alignment is re
established per SOI-63.01.
Preferred Evaluation Location: Preferred Evaluation Method:
Simulator X In-Plant Perform X Simulate
References: SOI-63.01 "Safety Injection System" Rev. 24
Task Number:: RO-063-SOI-63-016 APPLICABLE FOR: RO/SRO
IOCFR55.45: 3, 4, 6, 7
Validation Time: 10 min. Time Critical: No
Applicant: Time Start:
NAME SSN Time Finish:
Performance Rating: SAT _ UNSAT Performance Time
Examiner: /
NAME SIGNATURE DATE
COMMENTS
JPMR055/Sim
Page 3 of 10
SIMULATOR OPERATOR INSTRUCTIONS:
1. Initialize to IC # 146 100% steady state power.
2. Acknowledge all alarms.
3. Freeze simulator until the performance indicates understanding of the task and time
is allowed for control board familiarization.
4. NOTE: This JPM has been preshot in IC #146. The following is the setup instructions
if needed:
Initialize to IC # 40.
Vent Cold Leg Accumulator 1 to 610 to 620 psig as follows:
Place 1-HS-63-127A in Open Position.
Place 1-HIC-63-65A in Open Position.
Close both valves after pressure is lowered.
Ensure 1-HS-63-64A, in the CLOSE position.
Acknowledge all alarms
5. After performer indicates understanding of task, place simulator in run.
SIMULATOR OPERATOR INSTRUCTIONS:
NONE
JPMR055ISim
Page 4 of 10
Tools/Equipment/Procedures Needed:
Ensure clean copy of SOI-63-01 in all copies of Operating Instructions on the Simulator
Floor.
READ TO OPERATOR
DIRECTION TO TRAINEE:
I will explain the initial conditions, and state the task to be performed. All control
room steps shall be performed for this JPM, including any required
communications. I will provide initiating cues and reports on other actions when
directed by you. Ensure you indicate to me when you understand your assigned
task. To indicate that you have completed your assigned task return the handout
sheet I provided you.
INITIAL CONDITIONS:
The Unit is at 100% RTP
Cold Leg Accumulator (CLA) 1 pressure Hi/Lo alarm is illuminated.
You are the Operator at the Controls (OAC).
INITIATING CUES:
The Unit Supervisor directs you to increase CLA 1 Nitrogen Pressure to normal
by adding Nitrogen.
You are to notify Unit Supervisor when you have completed the task.
JPMR055/Sim
Page 5 of 10
START TIME:
STEP 1: Obtain a copy of the procedure.
STANDARD: A copy of SOI-63.01 section 8.6 has been obtained
EXAMINER'S CUE: After the performerhas demonstratedthe method of
obtaining the correctinstruction, the evaluatorcan UNSAT
provide a copy of the instruction.
COMMENTS:
CAUTION: Adding N2 to more than one CLA at a time while they are required
to be operable places the plant outside design basis. This section
is to be used to add N2 to any selected single CLA. If more than
one CLA needs N2 , separate evolutions must be performed.
NOTE e This section adds N2 to in-service CLAs that are indicating normal
level, and have a N2 atmosphere.
" If N2 is added to a CLA with low level, subsequent level rises could
result in overpressurizing the CLA with associated airborne
release.
" Rising CLA level may restore CLA pressure to within limits without
adding N2.
4
STEP 2: [Step 1] IF CLA level needs to be raised prior to adding N2,
THEN GO TO Section 8.3.
STANDARD: Performer determines that level in CLA Accumulator #1 is SAT
adequate by checking 1-LI-63-119 and -129 or from initiating
cue and proceeds to the next step.
UNSAT
COMMENTS:
"**Italicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMR055/Sim
Page 6 of 10
STEP 3: [STEP 2] OPEN applicable valve to place corresponding PCV
in service (N/A valve NOT used*:
NOMENCLATURE LOCATION POSITION UNID
N2 BANK A CNTMT ISOL A9X/729 OPEN 0-ISV-77-859A
(0-PCV-77-253)
N2 BANK B CNTMT ISOL A9X/729 OPEN 0-ISV-77-859B
(0-PCV-77-254)
STANDARD: Performer contacts an AUO to open either 0-ISV-77-859A or SAT
0-ISV-77-859B.
- CUE: When contacted, respond as AUO, acknowledge request
using repeat back, then report that valve 0-ISV-77-859A UNSAT
or B has been opened (valve requested to be opened).
COMMENTS:
I-
CAUTION The consequences of not verifying I-FCV-63-65 closed in
the next step could cause the pressure to drop below T/S
limit.
+
STEP 4: [STEP 3] ENSURE the following: CRITICAL
STEP
NOMENCLATURE LOCATION POSITION UNID
CLA N2 VENT HDR CONTROL 1-M-6 CLOSED 1-HIC-63-65
N2 HDR TO CL ACCUMS 1-M-6 OPEN 1-FCV-63-64
STANDARD: 1-HIC-63-65 controller output is 0%. Hand switch for I-HS-63 SAT
64A has been placed in the OPEN position.
Step is critical to assure N2 is aligned to header that
supplies CLA's. UNSAT
NOTE TO EVALUATOR: Underlined portion is critical.
COMMENTS:
"**Italicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMR055/Sim
Page 7 of 10
STEP 5: [STEP 4] PERFORM the following for selected N2 supply (N/A CRITICAL
vlvs not selected): STEP
NOMENCLATURE LOCATION POSITION UNID
N2 TO CL ACCUM 1 1-M-6 OPEN 1-FCV-63-127
N2 TO CL ACCUM 2 1-M-6 OPEN 1-FCV-63-107
N2 TO CL ACCUM 3 1-M-6 OPEN 1-FCV-63-87
N2 TO CL ACCUM 4 1-M-6 OPEN 1-FCV-63-63
STANDARD: Hand switch for 1-HS-63-127A has been placed in the OPEN SAT
position and 1-FCV-63-127 is verified open with associated
hand switch red light ON green light OFF.
Step is critical to open flow path to supply N2 to CLA UNSAT
Accumulator #1.
NOTE TO EVALUATOR: Underlined portion is critical.
COMMENTS:
i
STEP 6: [STEP 5] WHEN CLA(s) at desired pressure, THEN CRITICAL
PERFORM the following for selected N 2 sup (N/A vlvs not STEP
selected):
NOMENCLATURE LOCATION POSITION UNID
N2 TO CL ACCUM 1 1-M-6 CLOSED 1-FCV-63-127
N2 TO CL ACCUM 2 1-M-6 CLOSED 1-FCV-63-107
N2 TO CL ACCUM 3 1-M-6 CLOSED 1-FCV-63-87
N2 TO CL ACCUM 4 1-M-6 CLOSED 1-FCV-63-63
STANDARD: After pressure has been restored to Ž 617 psig & < 660 psig on SAT
1-PI-63-128 &/or PI-63-128, 1-HS-63-127A is placed in the
CLOSE position. and 1-FCV-63-127 is verified closed with
associated hand switch green light ON red light OFF.
UNSAT
Step is critical to close flow of N2 flow path to CLA
Accumulator #1.
NOTE TO EVALUATOR: Underlined portion is critical.
COMMENTS:
- ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMR055/Sim
Page 8 of 10
STEP 7: [STEP 6] CLOSE 1-FCV-63-64, N2 HDR TO CL ACCUMS
CRITICAL
STANDARD: Hand switch for 1-HS-63-64A has been placed in the CLOSE STEP
position.
Step is critical to close second valve in flow path to CLA SAT
Accumulator #1.
COMMENTS: UNSAT
STEP 8: [STEP 7] ENSURE selected CLA is at desired press [Alarm
131-134-B, CL ACCUM 1(2,3,4) PRESS HI/LO]
STANDARD: Annunciator alarm window 131-B is checked DARK. SAT
COMMENTS:
UNSAT
STEP 9: [STEP 8] WHEN Accumulator N 2 fill COMPLETE, THEN
PERFORM the following:
NOMENCLATURE LOCATION POSITION UNID
N2 BANK A CNTMT ISOL A9X/729 CLOSED 0-ISV-77-859A
(0-PCV-77-253)
N2 BANK B CNTMT ISOL A9X/729 CLOSED 0-ISV-77-859B
(0-PCV-77-254)
STANDARD: Performer contacts an AUO to close the valve opened earlier SAT
(JPM Step 3) either 0-ISV-77-859A or 0-ISV-77-859B.
- CUE: When contacted, respond as AUO, acknowledge request
using repeat back, then report that valve 0-ISV-77-859A UNSAT
or B has been closed (valve requested to be closed). The
Rad waste AUO has completed the IV.
COMMENTS:
"**ltalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMR055/Sim
Page 9 of 10
STEP 10: Notify the Unit Supervisor that N2 addition to CLA 1 is
complete.
STANDARD: Unit Supervisor has been notified that N2 addition to CLA 1
has been completed.
UNSAT
- CUE: When notified, acknowledge the report using "repeat
back"
COMMENTS:
END OF TASK
TIME STOP:
- ltalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Page 10 of 10
APPLICANT CUE SHEET
(TO BE RETURNED TO EXAMINER UPON COMPLETION OF TASK)
DIRECTION TO TRAINEE:
I will explain the initial conditions, and state the task to be performed.. All control
room steps shall be performed for this JPM, including any required
communications. I will provide initiating cues and reports on other actions when
directed by you. Ensure you indicate to me when you understand your assigned
task. To indicate that you have completed your assigned task return the handout
sheet I provided you.
INITIAL CONDITIONS:
The Unit is at 100% RTP
Cold Leg Accumulator (CLA) 1 pressure HilLo alarm is illuminated.
You are the Operator at the Controls (OAC).
INITIATING CUES:
The Unit Supervisor directs you to increase CLA 1 Nitrogen Pressure to normal
by adding Nitrogen.
You are to notify Unit Supervisor when you have completed the task.
JPMR028A/Sim
Page 1 of 18
REGION II
INITIAL LICENSE EXAMINATION
B.l.d JPMR028A/Sim
START A REACTOR COOLANT PUMP PER SOI-68.02
APPLICANT
EXAMINER
JPMR028A/Sim
Page 2 of 18
REGION I!
INITIAL LICENSE EXAMINATION
Task: START A REACTOR COOLANT PUMP PER SOI-68.02
Alternate Path: After RCP is started, its #1 seal will fail requiring the performer to stop the
RCP based on pump bearing temperature.
Facility JPM #: 3-OT-JPMR028A Rev 3
K/A Rating(s): 003K1.03 (3.3/3.6) 003K1.12 (3.0/3.3) 003A.3.01 (3.3/3.2)
003A3.03 (3.2/3.1) 003A3.04 (3.6/3.6) 003A.4.01 (3.3/3.2)
003A4.04 (3.1/3.0)
Task Standard: RCP #1 is started per SOI-68.02. Then RCP #1 is stopped due to high bearing
temperature.
Preferred Evaluation Location: Preferred Evaluation Method:
Simulator X In-Plant Perform X Simulate
References: SOI-68.02 "Reactor Coolant Pumps" Rev. 15
AOI-24 "RCP Seal Abnormalities During Pump Operation" Rev 20
Task Number:: RO-068-SOI-68-007 APPLICABLE FOR: RO/SRO
IOCFR55.45: 3, 4, 6, 7
Validation Time: 18 min. Time Critical: No
Applicant: Time Start:
NAME SSN Time Finish:
Performance Rating: SAT _ UNSAT _ Performance Time
Examiner: /
NAME SIGNATURE DATE
COMMENTS
JPMR028A/Sim
Page 3 of 18
SIMULATOR OPERATOR INSTRUCTIONS:
1. Initialize to IC # 147 BOL Mode 3..
2. Acknowledge all alarms.
3. Freeze simulator until the performance indicates understanding of the task and time
is allowed for control board familiarization.
4. NOTE: This JPM has been preshot in IC #147. The following is the setup instructions
if needed:
Initialize to IC # 49.
Drive control banks to 0 steps.
Place HS-68-8BA (RCP # 1) in the STOP position.
Place HS-68-8AA (RCP # 1) in the PUSHED IN position.
Plave 1-PIC-68-340D "Loop 1 Spray Control" in MANUAL and CLOSED
Insert the following:
ior zdihs629a (el) open RCP #1 Seal Return Valve OPEN to manual trigger 1.
imf cv17a (el) 100 to fail seal #1 on RCP #1 to 100% is assigned to manual
trigger 1.
Ensure the following indications are correct:
- #1 Seal AP > 200 psig
- Thermal Barrier Flow Ž_ 40 gpm
- Lower Bearing Flow > 5 gpm
- Upper Bearing Flow > 150 gpm
- Seal Water HTX Flow > 215 gpm
- RCP Seal Flow 8 to 13 gpm
- VCT Pressure >_17 psig
- Seal Leakoff > 0.2 gpm
- Aux Overcurrent Protection ACB Indicating Lights Energized
Acknowledge all alarms.
5. After performer indicates understanding of task, place simulator in run.
SIMULATOR OPERATOR INSTRUCTIONS:
After performer has stopped #1 RCP's Oil Lift Pump (Performance step 23) than insert
the following over rides by activating manual trigger 1: imf itrigger
ior 62hs9a open to fail #1 RCP Seal Return open.
imf cvl 7a 100 to fail #1 seal to 100%
JPMR028A/Sim
Page 4 of 18
ToolslEquipment/Procedures Needed:
Ensure clean copy of SOI-68.02 in all copies of Operating Instructions on the Simulator
Floor.
READ TO OPERATOR
DIRECTION TO TRAINEE:
I will explain the initial conditions, and state the task to be performed. All control
room steps shall be performed for this JPM, including any required
communications. I will provide initiating cues and reports on other actions when
directed by you. Ensure you indicate to me when you understand your assigned
task. To indicate that you have completed your assigned task return the handout
sheet I provided you.
INITIAL CONDITIONS:
The Unit is in Mode 3, Hot Standby.
RCP # 1 has been shut down 24 hours2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br /> for repairs to the motor leads.
Maintenance reported the repairs have been completed.
An AUO has performed Checklist 3, RCP Local Inspection.
All conditions are normal.
You are the Operator at the Controls (OAC).
INITIATING CUES:
The Unit Supervisor has directed you to start RCP #1 per procedure.
You are to notify the Unit Supervisor when the procedure is complete.
JPMR028A/Sim
Page 5 of 18
START TIME:
STEP 1: Obtain a copy of the procedure.
STANDARD: A copy of SOI-68.02 section 5.0 has been obtained
EXAMINER'S CUE: After the performerhas demonstratedthe method of
obtainingthe correctinstruction,the evaluatorcan UNSAT
provide a copy of the instruction.
COMMENTS:
i
NOTE This instruction may be repeated as deemed necessary by the
US/SRO.
I1
STEP 2: [Step 1] REVIEW Section 3.0, Precautions and Limitations.
STANDARD: Section 3.0 has been reviewed.
COMMENTS:
UNSAT
4-
STEP 3: [Step 2] VERIFY Section 4.2, Field Preparations,
COMPLETE.
STANDARD: Section 4.2 has been checked complete. SAT
- CUE: Inform performer that Section 4.2 has been completed.
UNSAT
COMMENTS:
I ____________________________
"**ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMR028A/Sim
Page 6 of 18
NOTE RCP status may be checked by remote indications if cntmt
conditions do not permit access per PAI-2.03.
NOTE Step [3] is NIA if not performed.
STEP 4: [Step 3] IF containment conditions permit access, THEN
PERFORM Checklist 3, "RCP Local Inspection". SAT
STANDARD: Information given in initial conditions. No action required.
UNSAT
- CUE: If asked, the local checklist 3 has been performed
COMMENTS:
STEP 5: [STEP 4] WHEN RCS press is greater than 100 psig,
ENSURE the following:
NOMENCLATURE LOCATION POSITION UNID
RCP 1 SEAL RETURN 1-M-5 OPEN 1-FCV-62-9
RCP 2 SEAL RETURN 1-M-5 OPEN 1-FCV-62-22
RCP 3 SEAL RETURN 1-M-5 OPEN 1-FCV-62-35
RCP 4 SEAL RETURN 1-M-5 OPEN 1-FCV-62-48
STANDARD: Performer verifies red open indication for above valves are lit. SAT
COMMENTS:
UNSAT
"**Italicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
- JPMR028A/Sim
Page 7 of 18
NOTE: Procedure step [5] & [6] are NIA if not performed.
Performance Step 6 and Step 7 relate to the Procedure Steps 5 & 6
STEP 6: [Step 5] IF no RCP's are in service THEN
EVALUATE the following criteria to determine if a potential SAT
"pocket" of low boron concentration exists:
"* Plant configuration since the last RCP was removed from
service (unexplainable decrease in Primary Water Storage
Tank level since last RCP was removed from service. UNSAT
"* Change in RCS boron concentration since last RCP was
removed from service.
"* Loss of 0ffsite power during post refueling dilution to
criticality.
"* During refueling, the Cold Leg Accumulator level decrease
without a corresponding increase in Hold Up Tank level.
"* Any natural circulation cooldown where boration has
occurred.
- Any Post SGTR condition where natural circulation
cooldown has occurred.
STANDARD: Performer determines that step in not applicable and N/As
step.
COMMENTS:
"**ItalicizedCues Are To Be Used Only lf JPM PerformanceIs Being Simulated.
JPMR028A/Sim
Page 8 of 18
STEP 7: [Step 6] IF a "pocket" is suspected in RCS THEN
EVALUATE the following criteria to determine if a potential SAT
"pocket" of low boron concentration exists:
Plant configuration since the last RCP was removed from
service (unexplainable decrease in Primary Water Storage
Tank level since last RCP was removed from service. UNSAT
[a] INITIATE sampling of boron concentration for the
potential areas of concern.
[b] EVALUATE the samples to determine potential
"pockets" of low concentration boron in the RCS.
[c] COORDINATE with Reactor Engineering to develop an
ACTION PLAN to address the "pocket" of low boron
concentration.
[d] DO NOT start an RCP, UNTIL
ACTION PLAN has addressed the "pocket" of low
boron concentration.
STANDARD: Performer determines that step in not applicable and N/As
step.
COMMENTS:
NOTE: Procedure Steps [7] thru [23] are performed for each RCP to
be started.
STEP 8: [Step 7] ENSURE the following parameters [0-M-27B]:
[a] Thermal Barrier Flow 35-50 gpm SAT
[b] LWR Oil CIr flow greater than 5 gpm
[c] UPR Oil CIr flow greater than 170 gpm
[d] RCP Seal Water Hx flow greater than 215 gpm
UNSAT
STANDARD: Thermal Barrier (1-FI-70-115), Lower oil cooler (1-FI-70-119),
Upper oil cooler (1-FI-70-116), and Seal Water HTX (1-FI-70
176) flows of specified values are verified.
COMMENTS:
"**ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMR028A/Sim
Page 9 of 18
CAUTION Inadvertent RCP start may occur if RCP alternate supply
breaker is left in its automatic configuration (pulled out).
NOTE Oil Lift Pump is started 2 minutes before RCP start.
STEP 9: [STEP 8] ENSURE the following: CRITICAL
STEP
NOMENCLATURE LOCATION POSITION UNID
RCP 1 NORMAL BKR & LIFT 1-M-5 PULL OUT, 1-HS-68-8AA
PUMP THEN START
RCP 2 NORMAL BKR & LIFT 1-M-5 PULL OUT, 1-HS-68-31AA
PUMP THEN START
RCP 3 NORMAL BKR & LIFT 1-M-5 PULL OUT, 1-HS-68-50AA
PUMP THEN START
RCP 4 NORMAL BKR & LIFT 1-M-5 PULL OUT, 1-HS-68-73AA
PUMP THEN START
STANDARD: Hand switch 1-HS-68-8AA has been "pulled out" and placed to SAT
the START position.
Step is critical to assure oil lift pressure thrust bearings to
prevent metal to metal contact on bearing surfaces when UNSAT
pump is started from idle.
COMMENTS:
STEP 10: [Step 9] VERIFY #1 seal AP greater than 200 psid [1-M-5].
STANDARD: #1 seal AP for RCP 1 verified greater than 200 psid on 1-PDI
62-8A.
UNSAT
COMMENTS:
"**Italicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMR028A/Sim
Page 10 of 18
I
STEP 11: [Step 10] VERIFY 8 to 13 gpm to RCP seal [1-M-5].
STANDARD: RCP I seal flow indicated between 8 and 13 gpm verified on 1
FI-62-1A.
UNSAT
NOTE TO EVALUATOR: Performer may make adjustment of seal injection
flow.
COMMENTS:
I
STEP 12: [Step 11] ENSURE VCT press at least 15 psig [1-M-6].
STANDARD: VCT indicated pressure verified greater than 15 psig on 1-PI
UNSAT
COMMENTS:
i
STEP 13: [Step 12] VERIFY #1 seal leakoff greater than 0.2 gpm or
within Normal Operating Range for existing #1 Seal AP (see SAT
Appendix B).
UNSAT
STANDARD: Seal leakoff from RCP 1 verified greater than 0.2 gpm or within
Normal Operating Range by red pen of 1-FR-62-23 and 24
respectively.
COMMENTS:
"**ItalicizedCues Are To Be Used Only If JPM Performanceis Being Simulated.
JPMR028A/Sim
Page 11 of 18
I
STEP 14: [Step 13] IF leakoff flow is not established, THEN GO TO
Section 8.0. SAT
STANDARD: Performer verifies seal flow established and goes to next step.
UNSAT
COMMENTS:
STEP 15: [Step 14] ENSURE RCS press is greater than 325 psig but
less than 1000 psig. SAT
[a] OPEN 1-FCV-62-53, #1 SEAL BYPASS [1-M-51 to VENT
RCP.
[b] CLOSE 1-FCV-62-53, #1 SEAL BYPASS [1-M-5].
UNSAT
STANDARD: Performer determines that this step does not apply and
proceeds to the next step.
COMMENTS:
NOTE: Step [15] prevents excessive Rod motion upon starting RCP.
NOTE TO EVALUATOR: The above note refers to JPM Step 16, I
______________
i
STEP 16: [Step 15] IF restarting RCP with Control Rods withdrawn,
THEN PLACE Rod Bank Select in MANUAL after matching SAT
Tavg with Tref.
UNSAT
STANDARD: Performer determines that this step does not apply, NAs this
step and proceeds to the next step.
COMMENTS:
- Italicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMR028A/Sim
Page 12 of 18
CAUTION To reduce thermal shock to RCP shaft and seals, a maximum
of 1°F per minute temp reduction will be observed, until
bearing temp is less than 225 0 F.
STEP 17: [Step 16] IF restarting RCP after stopping due to high temp
limits caused by loss of Injection Water and High CCS temp, SAT
THEN ENSURE following parameters established to prevent
thermal shock to RCP parts:
[a] CCS temp to thermal barrier less than 105°F (CCS Hx
outlet). UNSAT
[b] Seal leakoff temp less than 180'F.
[c] 0.2 to 5 gpm seal flow
STANDARD: Performer determines that this step does not apply and
proceeds to the next step.
- CUE: If asked, inform performer that this condition does not
apply to current situation.
COMMENTS:
STEP 18: [Step 17] ENSURE Aux OC Bkr, CLOSED.
STANDARD: Performer verifies red ACB position indicating light for RCP 1
Aux Overcurrent Protection ACB illuminated.
UNSAT
COMMENTS:
"**Italicized Cues Are To Be Used Only If JPM Performance Is Being Simulated.
JPMR028A/Sim
Page 13 of 18
STEP 19: [Step 18] IF starting RCP 1, THEN ENSURE Pzr spray, 1
PCV-68-340D, is CLOSED. SAT
STANDARD: 1-PCV-68-340D has been checked in the CLOSED position by
1-XI-68-340D green light lit. UNSAT
COMMENTS:
STEP 20: [Step 19] IF starting RCP 2, THEN ENSURE Pzr spray, 1
PCV-68-340B, is CLOSED. SAT
STANDARD: NO action required, not starting loop #2 RCP, however 1
PCV-340B may be checked in the CLOSED position by 1-XI UNSAT
68-340B green light lit.
COMMENTS:
i
STEP 21: [Step 20] ANNOUNCE RCP start on plant PA system.
STANDARD: Performer simulates announcement of RCP start on plant PA
system.
UNSAT
COMMENTS:
- ltalicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMR028A/Sim
Page 14 of 18
NOTE: Below 15% power with station service NOT transferred, the
Alternate handswitch is used to start RCP.
STEP 22: [STEP 21] START selected RCP (N/A HSs not used): CRITICAL
STEP
NOMENCLATURE LOCATION POSITION UNID
RCP 1 NORMAL BKR & LIFT 1-M-5 PUSH IN, 1-HS-68-8AA
PUMP THEN START
RCP 1 ALTERNATE BKR & 1-M-5 PUSH IN, 1-HS-68-8BA
XFER SELECTOR THEN START
RCP 2 NORMAL BKR & LIFT 1-M-5 PUSH IN, 1-HS-68-31AA
PUMP THEN START
RCP 2 ALTERNATE BKR & 1-M-5 PUSH IN, 1-HS-68-31 BA
XFER SELECTOR THEN START
RCP 3 NORMAL BKR & LIFT 1-M-5 PUSH IN, 1-HS-68-50AA
PUMP THEN START
RCP 3 ALTERNATE BKR & 1-M-5 PUSH IN, 1-HS-68-50BA
XFER SELECTOR THEN START
RCP 4 NORMAL BKR & LIFT 1-M-5 PUSH IN, 1-HS-68-73AA
PUMP THEN START
RCP 4 ALTERNATE BKR & 1-M-5 PUSH IN, 1-HS-68-73BA
XFER SELECTOR THEN START
STANDARD: 1-HS-68-8BA has been pushed in and placed to the START SAT
position, and RCP 1 amps and flow verified to be within proper
range after appropriate time delay (pump is up to normal
speed).
UNSAT
Step is critical to close breaker supplying RCP #1.
COMMENTS:
I _____________
"**ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMR028A/Sim
Page 15 of 18
1
STEP 23: [STEP 22] WHEN RCP has operated 1 minute, THEN STOP
Oil Lift Pump with applicable handswitch (N/A HSs not used):
NOMENCLATURE LOCATION POSITION
RCP 1 NORMAL BKR & LIFT 1-M-5 PULL OUT,
PUMP THEN STOP
RCP 2 NORMAL BKR & LIFT 1-M-5 PULL OUT,
PUMP THEN STOP
RCP 3 NORMAL BKR & LIFT 1-M-5 PULL OUT,
PUMP THEN STOP
RCP 4 NORMAL BKR & LIFT 1-M-5 PULL OUT,
PUMP THEN STOP
STANDARD: Handswitch 1-HS-68-8AA has been "pulled out" and placed to SAT
the STOP position.
UNSAT
COMMENTS:
+1
CONSOLE OPERATOR inserts the following when oil lift pump is stopped:
OVERRIDE 62HS9A TO FAIL 'AS IS' (#1 RCP Seal Return)
INSERT MALFUNCTION CV17A @ 100% -FAILS #1 SEAL
--- I
STEP 24: Performer transitions to AOI-24 or performer determine that the
bearing temperature will exceed limit and stops the Reactor CRITICAL
Cooling pump. STEP
STANDARD: Performer transitions to AOI-24 or 1-HS-68-8BA is placed in
the STOP position and green ACB position indicating light is
illuminated.
Step is to prevent additional damage to RCP #1 Seal
UNSAT
Package.
NOTE TO EVALUATOR: Underlined portion critical if performed at this
time. The performer may elect to stop RCP since it was
just started.
COMMENTS:
I
"**ltalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated,
JPMR028A/Sim
Page 16 of 18
NOTE TO EVALUATOR: The following steps are from AOI-24 Section
3.2. The performer may refer to ARI for 99D or IOOD.
CAUTION A seal leakoff rise to greater than 2.0 gpm AFTER
experiencing low leakoff of less than 0.8 gpm may indicate
seal degradation. Plant Management should be notified of
leakoff trends.
NOTE Anytime #1 seal leakoff flow exceeds the values shown on
attachment 1, system engineering should be requested to
perform an evaluation of the #11 seal condition.
During plant startup after seal maintenance, the #1 seal
may require 24 hours2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br /> of run time before the seal fully seats
fully and operates normally.
The #1 seal return should be isolated between 3 and 5
minutes after tripping an RCP to allow for pump
coastdown.
+
STEP 25: [Step 1] MONITOR #1 seal leakoff equal to or greater than
6.0 gpm.
STANDARD: Performer determines seal leakoff flow is equal to or greater
than 6 gpm by checking Seal Leakoff - High Range - flow
recorder 1-FR-62-24 Red Pen.
UNSAT
COMMENTS:
+
STEP 26: [Step 2] MONITOR RCPs lower bearing and #1 seal outlet
temp STABLE or DROPPING.
STANDARD: Performer determines RCPs lower bearing and #1 seal outlet
temperatures are increasing and transitions to the RNO
column.
UNSAT
COMMENTS:
"**Italicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMR028A/Sim
Page 17 of 18
STEP 27: [Step 2 RNO] IF reactor power greater than P8, THEN TRIP
CRITICAL
reactor.
IF reactor power less than or equal to P-8 THEN PLACE rods STEP
in MAN.
STOP affected RCP.
STANDARD: 1-HS-68-8BA is placed in the STOP position and green ACB
position indicating light is illuminated. Step is to prevent
additional damage to RCP #1 Seal Package.
UNSAT
- CUE: After RCP is stopped, state that we will stop here.
COMMENTS:
END OF TASKI
TIME STOP:
- ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Page 18 of 18
APPLICANT CUE SHEET
(TO BE RETURNED TO EXAMINER UPON COMPLETION OF TASK)
DIRECTION TO TRAINEE:
I will explain the initial conditions, and state the task to be performed. All control
room steps shall be performed for this JPM, including any required
communications. I will provide initiating cues and reports on other actions when
directed by you. Ensure you indicate to me when you understand your assigned
task. To indicate that you have completed your assigned task return the handout
sheet I provided you.
INITIAL CONDITIONS:
The Unit is in Mode 3, Hot Standby.
RCP # 1 has been shut down 24 hours2.777778e-4 days <br />0.00667 hours <br />3.968254e-5 weeks <br />9.132e-6 months <br /> for repairs to the motor leads.
Maintenance reported the repairs have been completed.
An AUO has performed Checklist 3, RCP Local Inspection.
All conditions are normal.
You are the Operator at the Controls (OAC).
INITIATING CUES:
The Unit Supervisor has directed you to start RCP #1 per procedure.
You are to notify the Unit Supervisor when the procedure is complete.
JPMR039/Sim
Page 1 of 8
REGION II
INITIAL LICENSE EXAMINATION
B.l.e JPMR039/Sim
START A THERMAL BARRIER BOOSTER PUMP PER
SOI-70.01
APPLICANT
EXAMINER
JPMR039/Sim
Page 2 of 8
REGION II
INITIAL LICENSE EXAMINATION
Task: START A THERMAL BARRIER BOOSTER PUMP PER SOI-70.01
Alternate Path: N/A
Facility JPM #: 3-OT-JPMR039 Rev 5
K/A Rating(s): 008A4.01 [3.3/3.1] 008A4.08 [3.1"/2.8]
Task Standard: 1A-A TBBP running with control switch in A-P AUTO (pulled out) and 1B-B TBBP
control switch in A-P Auto (pulled out).
Preferred Evaluation Location: Preferred Evaluation Method:
Simulator X In-Plant Perform X Simulate
References: SOI-70.01 "Component Cooling Water (CCS)" Rev. 39
Task Number:: RO-070-SOI-70-020 APPLICABLE FOR: RO/SRO
ICFR55.45: 3, 4, 6, 7
Validation Time: 7 min. Time Critical: No
Applicant: Time Start:
NAME SSN Time Finish:
Performance Rating: SAT__ UNSAT _ Performance Time
Examiner: /
NAME SIGNATURE DATE
COMMENTS
JPMR039/Sim
Page 3 of 8
SIMULATOR OPERATOR INSTRUCTIONS:
1. Initialize to IC # 156 place the simulator in run.
2. Acknowledge all alarms.
3. Shutdown T.B. Booster pumps and pull to lock.
4. Place simulator in run and clear all alarms.
5. Reset Hi-Flux at shutdown alarm at NI cabinet.
6. Ensure Source Range Count is Audible in Control Room.
SIMULATOR OPERATOR INSTRUCTIONS:
NONE
JPMR039/Sim
Page 4 of 8
Needed:
Tools/Equipment/Procedures
Ensure clean copy of SOI-70.01 in all copies of Operating Instructions on the Simulator
Floor.
READ TO OPERATOR
DIRECTION TO TRAINEE:
I will explain the initial conditions, and state the task to be performed. All control
room steps shall be performed for this JPM, including any required
communications. I will provide initiating cues and reports on other actions when
directed by you. Ensure you indicate to me when you understand your assigned
task. To indicate that you have completed your assigned task return the handout
sheet I provided you.
INITIAL CONDITIONS:
Plant start-up after refueling outage which required complete shutdown of the
Component Cooling Water System (CCS).
The CCS has been return to service and is operating normally except for the Thermal
Barrier Booster Pumps (TBBP) which are shutdown.
Both TBBPs have been aligned and are available for service.
You are the OAC operator.
INITIATING CUES:
The Unit Supervisor has directed you to place IA-A TBBP in service and align
both TBBP control switches in normal alignment per the procedure.
You are to notify the Unit Supervisor when the procedure has been completed.
JPMR039/Sim
Page 5 of 8
START TIME:
STEP 1: Obtain a copy of the procedure.
STANDARD: -SAT
A copy of SOI-70.01 Section 5.4 has been obtained.
EXAMINER'S CUE: After the performer has demonstrated the method of
obtainingthe correctinstruction,the evaluatorcan UNSAT
provide a copy of the instruction.
- CUE: If asked, all of section 4.0 has been completed.
COMMENTS:
STEP 2: [Step 1] ENSURE Section 5.1 and 5.3 COMPLETE
STANDARD: Performer has determined that CCS has been determined to
be aligned, filled, and vented per task assignment. SAT
- CUE: When checked, Sections 5.1 and 5.3, have been
performed
CMNSUNSAT
COMMENTS:
I______________
"**Italicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMR039/Sim
Page 6 of 8
STEP 3: [Step 2] START either of the following (N/A pump not started): CRITICAL
STEP
NOMENCLATURE LOCATION POSITION UNID
THRM BAR BSTR PMP 1A 0-M-27B START 1-HS-70-131A
(TBBP)
THRM BAR BSTR PMP 1B 0-M-27B START 1-HS-70-130A
(TBBP)
STANDARD: 1-HS-70-131A has been placed in the START position. SAT
Step is critical in starting TBBP to establish flow.
COMMENTS: UNSAT
i
STEP 4: [STEP 3 ] MONITOR increase flow to approximately 160 gpm
on 1-FI-70-81, TH BAR RET HDR FLOW [0-M-27B].
STANDARD: 1-FI-70-81 has been checked for flow increase.
COMMENTS: UNSAT
I
STEP 5: [STEP 4] IF TBBP 1A is running (or available), THEN CRITICAL
ENSURE 1-HS-70-130A, THRM BAR BSTR PMP 1B (TBBP) STEP
in A-P AUTO.
STANDARD: 1-HS-70-130A has been placed in A-P AUTO position (pulled SAT
out).
Step is critical to ensure that pumps control switches are
aligned for either a process or accident signal. UNSAT
COMMENTS:
"**Italicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMR039/Sim
Page 7 of 8
STEP 6: [STEP 5 ] IF TBBP 1B is running (or available), THEN CRITICAL
ENSURE 1-HS-70-131A, THRM BAR BSTR PMP 1A (TBBP) STEP
in A-P AUTO.
STANDARD: 1-HS-70-131A has been placed in A-P AUTO position (pulled
out).
Step is critical to ensure that pumps control switches are UNSAT
aligned for either a process or accident signal.
COMMENTS:
I-
STEP 7: Notify the Unit Supervisor that 1A-A TBBP Pump is running
both TBBP pumps hand switches are in A-P AUTO.
STANDARD: The Unit Supervisor has been notified that 1A-A TBBP Pump
is running and both TBBP hand switches are in A-P-AUTO.
UNSAT
- CUE: When notified, acknowledge the report using repeat
back.
COMMENTS:
END OF TASK
TIME STOP:
"**Italicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Page 8 of 8
APPLICANT CUE SHEET
(TO BE RETURNED TO EXAMINER UPON COMPLETION OF TASK)
DIRECTION TO TRAINEE:
I will explain the initial conditions, and state the task to be performed. All control
room steps shall be performed for this JPM, including any required
communications. I will provide initiating cues and reports on other actions when
directed by you. Ensure you indicate to me when you understand your assigned
task. To indicate that you have completed your assigned task return the handout
sheet I provided you.
INITIAL CONDITIONS:
Plant start-up after refueling outage which required complete shutdown of the
Component Cooling Water System (CCS).
The CCS has been return to service and is operating normally except for the Thermal
Barrier Booster Pumps (TBBP) which are shutdown.
Both TBBPs have been aligned and are available for service.
You are the OAC operator.
INITIATING CUES:
The Unit Supervisor has directed you to place IA-A TBBP in service and align
both TBBP control switches in normal alignment per the procedure.
You are to notify the Unit Supervisor when the procedure has been completed.
JPMR168/Sim
Page 1 of 15
REGION II
INITIAL LICENSE EXAMINATION
B.l.f JPMR168/Sim
SHUTDOWN "A" TRAIN EGTS FOLLOWING 10
HOUR RUN PER SOI-65.02
APPLICANT
EXAMINER
JPMR168/Sim
Page 2 of 15
REGION I!
INITIAL LICENSE EXAMINATION
Task: SHUTDOWN "A" TRAIN EGTS FOLLOWING 10 HOUR RUN PER SOI-65.02
Alternate Path: N/A
Facility JPM #: New
KIA Rating(s): 027A4.01 (3.3-/3.3*) 027A4.01 (3.3*/3.2*) 2.1.23 (3.914.0)
2.1.30 (3.9/3.4)
Task Standard: EGTS "A" Train has been shutdown and returned to ES Standby alignment in
accordance with SOI-65.02.
Preferred Evaluation Location: Preferred Evaluation Method:
Simulator X In-Plant Perform X Simulate
References: SOI-65.02 "Emergency Gas Treatment System" Rev. 13
Task Number:: RO-065-SOI-65-005 APPLICABLE FOR: RO/SRO
1OCFR55.45: 3, 6, 8
Validation Time: 28 min. Time Critical: No
Applicant: Time Start:
NAME SSN Time Finish:
Performance Rating: SAT__ UNSAT Performance Time
Examiner: /
NAME SIGNATURE DATE
COMMENTS
JPMR168/Sim
Page 3 of 15
SIMULATOR OPERATOR INSTRUCTIONS:
1. Initialize to IC # 152 100% steady state power.
2. Acknowledge all alarms.
3. Freeze simulator until the performance indicates understanding of the task and time
is allowed for control board familiarization.
4. NOTE: This JPM has been preshot in IC #152. The following is the setup instructions
if needed:
Initialize to IC # 40.
Startup "A" Train EGTS per SOI-65.02 Section 8.3 as follows:
Open 1-FCV-65-10 with 1-HS-65-10.
Open 1-FCO-65-26 with 1-HS-65-26
Place 1-HS-65-81/86 to OPEN
Place 1-HS-65-83/87 in A AUTO STANDBY
Place 0-HS-65-23A to start and release.
Acknowledge all alarms
5. After performer indicates understanding of task, place simulator in run.
SIMULATOR OPERATOR INSTRUCTIONS:
NONE
JPMR168/Sim
Tools/Eauipment/Procedures Needed: Page 4 of 15
Ensure clean copy of SOI-65.02 in all copies of Operating Instructions on the Simulator
Floor.
READ TO OPERATOR
DIRECTION TO TRAINEE:
I will explain the initial conditions, and state the task to be performed. All control
room steps shall be performed for this JPM, including any required
communications. I will provide initiating cues and reports on other actions when
directed by you. Ensure you indicate to me when you understand your assigned
task. To indicate that you have completed your assigned task return the handout
sheet I provided you.
INITIAL CONDITIONS:
The Unit is at 100% RTP
0-SI-65-6-A "Emergency Gas Treatment System Train A 10-Hour Operation
performance in progress.
"A" Train EGTS Fan has been in service for 10 hours1.157407e-4 days <br />0.00278 hours <br />1.653439e-5 weeks <br />3.805e-6 months <br />.
You are a support operator in the control room.
INITIATING CUES:
The Unit Supervisor directs you shutdown the "A" Train EGTS Fan per SOI-65.02
and return EGTS to Standby Alignment per the procedure.
You are to notify Unit Supervisor when you have completed the task.
JPMR168/Sim
Page 5 of 15
START TIME:
STEP 1: Obtain a copy of the procedure.
STANDARD: A copy of SOI-65.02 section 7.1 has been obtained __SAT
EXAMINER'S CUE: After the performerhas demonstratedthe method of
obtaining the correctinstruction, the evaluatorcan
UNSAT
provide a copy of the instruction.
NOTE TO EVALUATOR: Performer may also identify Section 5.0 as
needed to return EGTS to standby. You may
provide a copy of this section when performer
seeks to obtain a copy.
COMMENTS:
CAUTION: If EGTS is in service due to an accident signal initiation, and the
charcoal filter banks have decay heat, an engineering evaluation
must be performed before shutting down the EGTS system.
NOTE If EGTS was Auto actuated, both Trains' shutdown sections must be
performed prior to return to standby readiness.
STEP 2: [Step 1] ENSURE a OA Cntmt Isolation signal is NOT
present.
STANDARD: Performer determines that OA Cntmt Isolation signal is NOT SAT
present by checking Master Isol Signal PNLs 1-XX-55-6C & 6D
OA light NOT LIT.
UNSAT
COMMENTS:
"**Italicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMR168/Sim
Page 6 of 15
STEP 3: [Step 2] Momentarily PLACE 0-HS-65-23A, EGTS FAN & CRITICAL
DISCH DMPR, in STOP (returns to A-AUTO). STEP
STANDARD: Performer stops "A" Train EGTS Fan with 0-HS-65-23A and
checks red light off and green light ON the associated
handswitch. SAT
Step is critical to shutdown the running EGTS Fan.
UNSAT
COMMENTS:
I
STEP 4: [Step 3] ENSURE 1-FCV-65-8, EGTS TR-A U1 SUCT
DMPR, CLOSED.
STANDARD: Performer checks 1-HS-65-8 and verifies red light off and SAT
green light ON for the associated hand switch
UNSAT
COMMENTS:
STEP 5: [Step 4] PERFORM the following: CRITICAL
[a] CLOSE 1-FCO-65-10, EGTS TR-A Ul SUCT DMPR. STEP
[b] CLOSE 1-FCO-65-26, EGTS TO Ul SHIELD BLDG.
STANDARD: Performer closes 1-FCO-65-10 with 1-HS-65-10, performer
closes 1-FCO-65-26 with 1-HS-65-26. Respective hand
switches red lights are off and green lights are LIT. UNSAT
Step is critical to shutdown return ventilation lineup to
normal following 10 hour1.157407e-4 days <br />0.00278 hours <br />1.653439e-5 weeks <br />3.805e-6 months <br /> run.
COMMENTS:
I __________________________
- ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMR168/Sim
Page 7 of 15
STEP 6: [STEP 5] IF Train A EGTS to be returned to STANDBY,
CRITICAL
THEN: PERFORM the following: STEP
NOMENCLATURE
EGTS TR-A U1 SUCT DMPR
EGTS TR-A Ul SHIELD BLDG
STANDARD: Performer places 1-HS-65-10 and 1-HS-65-26 to the A AUTO SAT
position.
Step is critical to return these hand switches to ES
Standby alignment. UNSAT
COMMENTS:
i
STEP 7: [Step 6] IF Train B EGTS is to be shutdown, THEN GO TO
Section 7.2.
STANDARD: Performer determines that this step does not apply and SAT
proceeds to the next step.
COMMENTS:
UNSAT
-I
STEP 8: [Step 7] IF EGTS is to be returned to STANDBY, THEN GO
TO Section 5.0 to align EGTS for STANDBY.
STANDARD: Performer goes to Section 5.0. SAT
COMMENTS:
UNSAT
I
- ltalicizedCues Are To Be Used Only if JPM PerformanceIs Being Simulated.
JPMR168/Sim
Page 8 of 15
NOTE TO EVALUATOR: The following performance steps are from
section 5.1 of SOI-65.02.
CAUTION IF EGTS is being returned to standby after auto actuation,
THEN both Sections 7.1 and 7.2 must be performed prior to
Standby Readiness alignment.
i
STEP 9: [Step 1] ENSURE a OA Cntmt Isolation signal is NOT
present.
STANDARD: Performer determines that OA Cntmt Isolation signal is NOT SAT
present by checking Master Isol Signal PNLs 1-XX-55-6C & 6D
OA light NOT LIT.
NOTE TO EVALUATOR: This was previously performed in step 2 of
_UNSAT
JPM.
COMMENTS:
I1 _____________
STEP 10: [STEP 2] PERFORM the following:
120VAC VITAL INST POWER BD 1-1
NOMENCLATURE LOCATION POSITION UNID
EGTS TRAIN A AUX RELAYS BKR 38 ON 1-BKR-235-1/38
1-PCV-65-81 /1-PCV-65-86
120VAC VITAL INST POWER BD 1-11
NOMENCLATURE LOCATION POSITION UNID
EGTS TRAIN B AUX RELAYS BKR 38 ON 1-BKR-235-2/38
1-PCV-65-81/1-PCV-65-87
STANDARD: An AUO is contacted to ensure 1-BKR-235-1/38 and 1-BKR SAT
235-2/38 are ON.
- CUE: When contacted, respond as AUO, acknowledge request
using repeat back, then report that 1-BKR-235-1138 and 1 UNSAT
BKR-2/38 are ON.
COMMENTS:
-- I _____________________________
"**Italicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMR168/Sim
Page 9 of 15
STEP 11: [STEP 3] PERFORM the following:
NOMENCLATURE LOCATION POSITION UNID
EGTS FAN A & DISCH DMPR O-M-27B A AUTO 0-HS-65-23A
EGTS FAN B & DISCH DMPR 0-M-27B A AUTO 0-HS-65-42A
STANDARD: Hand switches 0-HS-65-23A and 0-HS-65-42A have checked SAT
in the A AUTO position (pushed in).
COMMENTS:
UNSAT
STEP 12: [STEP 4] OPEN the following dampers, and PLACE the
handswitches in A AUTO:
NOMENCLATURE LOCATION POSITION UNID
Ul ANN VAC FANS SUCT 0-M-27B A AUTO 1-HS-65-52
Ul ANN VAC FANS SUCT 0-M-27B A AUTO 1-HS-65-53
STANDARD: Hand switches 0-HS-65-52 and 0-HS-65-53 have checked in SAT
the A AUTO position.
COMMENTS:
UNSAT
I _________________________________________________
"**ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMR168/Sim
Page 10 of 15
NOTE 1 The following step may be N/A'd if annulus fans are running.
NOTE 2 If a phase A signal has been present, the next step may start
one Ann Vac Fan due to low flow. Either fan may be selected
first. Flow should be allowed to stabilize before the second
fan is placed in auto to avoid two fans running. SOI-65.01
Section 5.0 should be referenced to ensure proper damper
alignment and control after fan start.
STEP 13: [STEP 5] PLACE the following handswitches in STOP to
break seal-in and , RETURN to A-P AUTO:
NOMENCLATURE LOCATION POSITION UNID
ANN VAC FAN 1A & SUCT FCO 0-M-27B A-P AUTO 1-HS-65-77A
ANN VAC FAN 1B & SUCT FCO 0-M-27B A-P AUTO 1-HS-65-74A
STANDARD: Performer determines ANN VAC FAN 1A is running by SAT
checking red light LIT on 1-HS-65-77A, that step is N/A and
proceeds to the next step.
COMMENTS: UNSAT
STEP 14: [STEP 6] IF an accident signal (0A) has occurred OR
Annulus AP has dropped below 4.0 in. H2 0, THEN:
[a] PERFORM the following:
NOMENCLATURE LOCATION POSITION UNID
Ul EGTS-ANN AP CNTLR B ISOL 0-M-27B A-AUTO 1-HS-65-83/87
Ul EGTS-ANN AP CNTLR A ISOL 0-M-27B A-AUTO 1-HS-65-81/86
STANDARD: Performer determines that step is NIA by checking Ul EGTS- SAT
ANN AP is greater than 4.0 " H2 0 on 1-PDI-30-126A.
Performer may also observe that Annunciator alarm window
232-B is DARK and proceeds to the next step.
UNSAT
- CUE: If asked, respond as CRO, and state that Window 232-B
has remained DARK throughout the 10 hour1.157407e-4 days <br />0.00278 hours <br />1.653439e-5 weeks <br />3.805e-6 months <br /> run of "A"
Train EGTS Fan.
COMMENTS:
"**ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMR168/Sim
Page 11 of 15
STEP 15: [STEP 6 b] WHEN Annulus AP is greater than 4.0 in. H 20,
THEN PERFORM the following (N/A if not required):
NOMENCLATURE LOCATION POSITION UNID
PCV-65-81 and PCV-65-86, A5W737, 1-JB- RESET 1-HS-65-80 and
EGTS CNTMTANNULUS DP 292-4013-A, N. 1-HS-65-90
RESET of GFFD Rm.
PCV-65-83 and PCV-65-87, A4V737, 1-JB- RESET 1-HS-65-82 and
EGTS CNTMTANNULUS DP 292-4015-B, S. 1-HS-65-97
RESET of GFFD Rm.
STANDARD: Performer determines that step is NIA by checking Ul EGTS SAT
ANN AP as greater than 4.0 " H20 on 1-PDI-30-126A.
Performer may also observe that Annunciator alarm window
232-B is DARK and proceeds to the next step.
UNSAT
COMMENTS:
STEP 16: [STEP 7] ENSURE the following dampers are CLOSED and,
PLACE either 1-HS-65-83/87 or 1-HS-65-81/86 in A AUTO,
and the other handswitch in A AUTO STANDBY:
NOMENCLATURE LOCATION AS-LEFT UNID
POSITION
Ul EGTS-ANN AP CNTLR B 0-M-27B 1-HS-65-83/87
ISOL
Ul EGTS-ANN AP CNTLR A 0-M-27B 1-HS-65-81/86
ISOL
STANDARD: Performer checks positions of 1-HS-65-83/87 and 1-HS-81/86 SAT
and ensures one switch is in A AUTO and the other switch is in
A-AUTO STANDBY.
COMMENTS: UNSAT
"**ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMR168/Sim
Page 12 of 15
CAUTION PDIC-65-80 & 82 Setpoint Thumbwheells are adjusted by MIG
STEP 17: [STEP 8] ENSURE the following controllers in AUTO:
NOMENCLATURE LOCATION POSITION UNID
EGTS-ANN AP CONTROL 0-M-27B AUTO 1-PDIC-65-82
EGTS-ANN AP CONTROL 0-M-27B AUTO 1-PDIC-65-80
STANDARD: Performer checks both handswitches (1-PDIC-65-82 & -80) are SAT
in AUTO.
COMMENTS:
UNSAT
i
STEP 18: [STEP 9] ENSURE the following:
NOMENCLATURE LOCATION POSITION UNID
EGTS TR A DECAY COOLING 0-M-27B CLOSE 0-HS-65-28B
EGTS TR A DECAY COOLING O-M-27B CLOSE 0-HS-65-28A
EGTS TR B DECAY COOLING O-M-27B CLOSE 0-HS-65-47A
EGTS TR B DECAY COOLING O-M-27B CLOSE 0-HS-65-47B
STANDARD: Performer check and verifies 0-HS-65-28B, -28A, -47A, -47B SAT
are in the close position.
COMMENTS:
UNSAT
I_____________________________
"**ltalicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMR168/Sim
Page 13 of 15
STEP 19: [STEP 10] PERFORM the following
NOMENCLATURE LOCATION POSITION UNID
EGTS TR-A Ul SUCT DMPR 0-M-27B A AUTO 1-HS-65-10
EGTS TR-A Ul SUCT DMPR 0-M-27B CLOSE 1-HS-65-8
EGTS FAN B U1 SUCT DMPR 0-M-27B CLOSE 1-HS-65-51
EGTS TR-B Ul SUCT DMPR 0-M-27B A AUTO 1-HS-65-30
EGTS TO Ul SHIELD BLDG 0-M-27B A AUTO 1-HS-65-26
EGTS TO Ul SHIELD BLDG 0-M-27B A AUTO 1-HS-65-27
STANDARD: Performer checks 1-HS-65-10 & -26 to the A AUTO position.
Performer checks 1-HS-65-8 & -51 in the CLOSE position.
Performer checks 1-HS-65-30, -26, -27 in the A AUTO position.
UNSAT
COMMENTS:
NOTE TO EVALUATOR I
The following step is from Section 7.1
I
STEP 20: [Step 8] IF Annulus Vacuum System was shutdown, THEN
PLACE Annulus Vacuum in service per SOI-65.01.
STANDARD: Performer determines that this step is not applicable as
annulus vacuum is already in service.
UNSAT
COMMENTS:
I ______________________________
- ItalicizedCues Are To Be Used Only lf JPM PerformanceIs Being Simulated.
JPMR168/Sim
Page 14 of 15
STEP 21: Notify the Unit Supervisor that "A"Train EGTS Fan has been
shutdown and EGTS has been returned to STANDBY.
STANDARD: Unit Supervisor has been notified that "A" Train EGTS Fan
has been shutdown and EGTS has been returned to
STANDBY. UNSAT
- CUE: When notified, acknowledge the report using "repeat
back"
COMMENTS:
END OF TASK
I______________
TIME STOP:
"**ltalicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Page 15 of 15
APPLICANT CUE SHEET
(TO BE RETURNED TO EXAMINER UPON COMPLETION OF TASK)
DIRECTION TO TRAINEE:
I will explain the initial conditions, and state the task to be performed. All control
room steps shall be performed for this JPM, including any required
communications. I will provide initiating cues and reports on other actions when
directed by you. Ensure you indicate to me when you understand your assigned
task. To indicate that you have completed your assigned task return the handout
sheet I provided you.
INITIAL CONDITIONS:
The Unit is at 100% RTP
0-SI-65-6-A "Emergency Gas Treatment System Train A 10-Hour Operation
performance in progress.
"A" Train EGTS Fan has been in service for 10 hours1.157407e-4 days <br />0.00278 hours <br />1.653439e-5 weeks <br />3.805e-6 months <br />.
You are a support operator in the control room.
INITIATING CUES:
The Unit Supervisor directs you shutdown the "A" Train EGTS Fan per SOI-65.02
and return EGTS to Standby Alignment per the procedure.
You are to notify Unit Supervisor when you have completed the task.
JPMR108A/Sim
Page 1 of 11
REGION II
INITIAL LICENSE EXAMINATION
B.l.g JPMR108A/Sim
RETURN PRM N-42 TO SERVICE PER AOI-4
APPLICANT
EXAMINER
JPMR1 08A/Sim
Page 2 of 11
REGION !1
INITIAL LICENSE EXAMINATION
Task: RETURN PRM N-42 TO SERVICE PER AOI-4
Alternate Path: When rod control is returned to auto a continuous rod insertion occurs
requiring performer to return rod control to manual and then trip the reactor.
Facility JPM #: 3-OT-JPMR108 Rev 1
K/A Rating(s): 015A4.02 [3.9/3.91 2.1.23 [3.9/4.0] 001AA1.05 [4.3/4.21
Task Standard: The DETECTOR CURRENT COMPARATOR switch for UPPER SECTION, the
DETECTOR CURRENT COMPARATOR switch for LOWER SECTION, the ROD
STOP BYPASS, the POWER MISMATCH BYPASS, and the COMPARATOR
CHANNEL DEFEAT have been placed in NORMAL or OPERATE as directed AOI-2,
Attachment 1 and then reactor is manually tripped due to continuous rod insertion.
Preferred Evaluation Location: Preferred Evaluation Method:
Simulator X In-Plant Perform X Simulate
References: AOI-4, NUCLEAR INSTRUMENTATION MALFUNCTIONS, Rev 20
Task Number:: RO-092-AOI-4-002 APPLICABLE FOR: RO/SRO
RO-085-AO 1-2-0 05
IOCFR55.45: 2,3, 4, 5,6,12
Validation Time: 9 min. Time Critical: No
Applicant: Time Start:
NAME SSN Time Finish:
Performance Rating: SAT UNSAT Performance Time
Examiner: /
NAME SIGNATURE DATE
COMMENTS
JPMR 108A/Sim
Page 3 of 11
SIMULATOR OPERATOR INSTRUCTIONS:
1. Initialize to IC # 157.
2. Acknowledge all alarms.
3. IFreeze simulator until the performance indicates understanding
of the task and time
is allowed for control board familiarization.
4. NOTE: This JPM has been preshot in IC #157. The
following is the setup
instructions if needed:
Initialize to IC #40, 50, or 60
imf rd02 (el) 20 "Uncontrolled Rod insertion Bank D
Group 2".
Place PRM N42 OOS:
- Place S/G LEVEL-NIS BIAS controllers for S/Gs
2 and 3 in MANUAL
and adjust to demand output of unaffected S/Gs.
"* Place DETECTOR CURRENT COMPARATOR
switch for UPPER
SECTION to N42
"* Place DETECTOR CURRENT COMPARATOR switch
for LOWER
SECTION to N42
"* Place ROD STOP BYPASS switch to N42
"* Place POWER MISMATCH BYPASS switch to N42
"* Place COMPARATOR CHANNEL DEFEAT switch
to N42
Acknowledge all alarms.
FREEZE the simulator till the performer indicates an
understanding of the task.
5. After performer indicates understanding of task, place
simulator in run.
SIMULATOR OPERATOR INSTRUCTIONS:
ENSURE rd 02 with 20 steps per minutes is assigned
to manual trigger 1.
When rod control has been returned to automatic (JPM
STEP 11 Completion), then
insert continuous rod insertion by activating manual
trigger 1:
imf itrigger
JPMR108ANSim
Page 4 of 11
Tools/Equipment/Procedures Needed:
Ensure clean copy of AOI-4 and AO1-2 in all copies of Abnormal Operating Instructions
on the Simulator Floor.
READ TO OPERATOR
DIRECTION TO TRAINEE:
I will explain the initial conditions, and state the task to be performed. All control
room steps shall be performed for this JPM, including any required
communications. I will provide initiating cues and reports on other actions when
directed by you. Ensure you indicate to me when you understand your assigned
task. To indicate that you have completed your assigned task return the handout
sheet I provided you.
INITIAL CONDITIONS:
Unit at 100% RTP
PRM N42 failed during last shift
AOI-4 Section 3.4 has been completed through Step 15.
Work Control has notified the MCR that repairs to PRM N42 are complete and the
instrument is ready to be returned to service.
You are the Operator at the Controls.
INITIATING CUES:
The Unit Supervisor has directed you to return PRM N42 to service.
You are to notify the US when the procedure has been completed.
JPMR108A/Sim
Page 5 of 11
START TIME:
STEP 1: Obtain the correct procedure.
STANDARD: A copy of AOI-4 has been obtained.
EXAMINER'S CUE: After the performer has demonstratedthe method of
obtaining the correct instruction,the evaluatorcan UNSAT
provide a copy of the instruction.
COMMENTS:
I
STEP 2: [Step 16] WHEN PRM is to be restored THEN:
a. PLACE controls rods in manual.
STANDARD: The rod control hand switch has been placed in Manual
position.
UNSAT
COMMENTS:
I
STEP 3: [Step 16b] REFER TO Attachment 1, PRM Function At NIS
Rack, step 2.
STANDARD: Performer refers to Attachment 1, PRM Function At NIS Rack,
Step 2 for restoration of PRM N42.
UNSAT
COMMENTS:
"**Italicized Cues Are To Be Used Only lf JPM PerformanceIs Being Simulated.
JPMRI 08A/Sim
Page 6 of 11
NOTE TO EVALUATOR: The following steps are from Attachment I page 2 6 of 11
JPMR108A/Sim
Page
of 2 AOI-4
STEP 4: [STEP 2] WHEN PRM is ready for return to service, THEN CRITICAL
PERFORM the following steps: STEP
a. PLACE DETECTOR CURRENT COMPARATOR switch for
UPPER SECTION in NORMAL
STANDARD: Detector Current Comparator Upper Section switch placed to
"NORMAL" (Miscellaneous Control & Indication Panel,I-IDWR
92-N50-G IV)
UNSAT
Step is critical for proper restoration of upper power
detector to current comparator.
COMMENTS:
CRTIA
STEP 5: [STEP 2 b] PLACE DETECTOR CURRENT COMPARATOR CRITICAL
switch for LOWER SECTION in NORMAL STEP
STANDARD: Detector Current Comparator Lower Section switch placed to
"NORMAL" (Miscellaneous Control & Indication Panel, 1-IDWR SAT
92-N50-G IV).
Step is critical for proper restoration of lower power
detector to current comparator. UNSAT
COMMENTS:
"**ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMR108A/Sim
Page 7 of 11
NOTE: On the following step, annunciator window 66-C, 67-C, 68-C, OR
69-C, N-(#) OVERPOWER ROD STOP BYPASSED, will clear
depending on which channel is bypassed.
STEP 6: [STEP 2 c] PLACE ROD STOP BYPASS switch in OPERATE.
CRITICAL
STEP
STANDARD: Rod Stop Bypass switch is positioned from "N42 to placed to
"OPERATE" (Miscellaneous Control & Indication Panel,1
IDWR-92-N50-G IV)
Step is critical for proper restoration of to enable rod stop
interlock protection from this channel. _UNSAT
COMMENTS:
STEP 7: [STEP 2 d] PLACE POWER MISMATCH BYPASS switch in CRITICAL
OPERATE.
STEP
_SAT
STANDARD: Power Mismatch Bypass switch is positioned from "N42" to
"OPERATE" (Miscellaneous Control & Indication Panel, 1
IDWR-92-N50-G IV)
UNSAT
Step is critical to restore channel input to high
auctioneering circuit and power mismatch circuits.
COMMENTS:
I __________________________
"**ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMR108A/Sim
Page 8 of 11
NOTE: On the following step, annunciator window 82-E, NIS CHANNEL IN
TEST, will clear.
I ______
STEP 8: [STEP 2 e] PLACE COMPARATOR CHANNEL DEFEAT switch in CRITICAL
NORMAL.
STEP
STANDARD: Comparator Channel Defeat Switch is positioned to "NORMAL" SAT
(Comparator & Rate Panel ,Comparator N37, 1-IDWR-92-N37
IV).
Step is critical to restore channel input to channel UNSAT
comparator alarm circuits.
COMMENTS:
NOTE: On the following step, annunciator window 115-E, POWER RANGE
FLUX RATE HI, will clear if the positive rate trip light is LIT.
STEP 9: [STEP 2 RNO fl IF POSITIVE RATE TRIP is LIT, THEN RESET
RATE MODE switch.
STANDARD: Positive Rate Trip light on Power Range Upper N42A, 1-IDWR-92- SAT
42A II, is checked and determine light is NOT LIT and continues to
next step.
COMMENTS:
UNSAT
NOTE TO EVALUATOR: Performer returns to AOI-4 at step 16 c.
STEP 10: [STEP 16 c] ENSURE T-avg and T-ref within 10.
STANDARD: Performer verifies T-avg and T-ref within 10 by recorder 1-TR
68-2B on 1-M-5 or other T-avg - T-ref indications.
COMMENTS: C__ UNSAT
"**ltalicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMR108A/Sim
Page 9 of 11
STEP 11: [STEP 16 d] IF auto rod control desired, PLACE control rods
in AUTO.
STANDARD: The rod control hand switch has been placed in AUTO
position. UNSAT
- CUE: If asked, respond as US that auto rod control is desired.
NOTE TO EVALUATOR: The continuous rod insertion malfunction
will be
inserted just after rod control has been placed to
auto. The operator may immediately return rod
control to manual, check for rod motion stopped,
then trip the reactor before referring to AOI-2.
COMMENTS:
NOTE TO EVALUATOR: The Following Steps are from AOI-2 Section 3.2
due to continuous rod insertion.
i
STEP 12: [STEP 1] PLACE control rods in MAN.
STANDARD: The rod control hand switch has been placed in Manual
position.
UNSAT
- NOTE: Rods will continue to step IN.
COMMENTS:
I._________________________
"**ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMR108A/Sim
Page 10 of 11
STEP 13: [STEP 2] CHECK control rod movement STOPPED.
STANDARD: The rod control indications have been checked for movement
and performer determines that rods are still inserting and goes
to RNO for step.
UNSAT
"**NOTE. Rods will continue to step IN.
COMMENTS:
.1-
STEP 14: [STEP 2 RNO] TRIP reactor. GO TO E-0, Reactor Trip or CRITICAL
Safety Injection. STEP
STANDARD: Reactor Trip hand switch on 1-M-4 or 1-M-6 has been placed
to the TRIP position. Performer than goes to E-0.
Step is critical to task performance as uncontrolled rod UNSAT
movement in manual rod control requires reactor trip
- CUE: When performer transitions to E-O, inform him/her that the
JPM is complete "WE'LL STOP HERE".
COMMENTS:
END OF TASKI
TIME STOP:
"**Italicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Page 11 of 11
APPLICANT CUE SHEET
(TO BE RETURNED TO EXAMINER UPON COMPLETION OF TASK)
DIRECTION TO TRAINEE:
I will explain the initial conditions, and state the task to be performed. All control
room steps shall be performed for this JPM, including any required
communications. I will provide initiating cues and reports on other actions when
directed by you. Ensure you indicate to me when you understand your assigned
task. To indicate that you have completed your assigned task return the handout
sheet I provided you.
INITIAL CONDITIONS:
Unit at 100% RTP
PRM N42 failed during last shift
AOI-4 Section 3.4 has been completed through Step 15.
Work Control has notified the MCR that repairs to PRM N42 are complete and the
instrument is ready to be returned to service.
You are the Operator at the Controls.
INITIATING CUES:
The Unit Supervisor has directed you to return PRM N42 to service.
You are to notify the US when the procedure has been completed.
JPMR095A/Sim
Page 1 of 13
REGION Ii
INITIAL LICENSE EXAMINATION
B.l.a JPMR095A/Sim
RETRIEVE A DROPPED ROD PER AOI-2
APPLICANT
EXAMINER
JPMR095A/Sim
Page 2 of 13
REGION II
INITIAL LICENSE EXAMINATION
Task: RETRIEVE A DROPPED ROD PER AOI-2
Alternate Path: Second rod drops while withdrawing dropped rod requiring a manual trip of
the reactor.
Facility JPM #: 3-OT-JPMR095A Rev 0
K/A Rating(s): 001A4.03 (4.0/3.7) 001A4.06 (2.9/3.2) 2.1.30 (3.9/3.4)
2.1.23 (3.9/4.0) 2.4.4 (4.0/4.3) 003AA1.02 (3.6/3.4)
003AA1.03 (3.6/3.3) 003AK3.04 (3.8/4.1 003AK3.09 (3.0/3.5)
Task Standard: Performer prepares for the withdrawal of the dropped rod per AOI-2, Section 3.3,
Steps 16-27.
Preferred Evaluation Location: Preferred Evaluation Method:
Simulator X In-Plant _ Perform X Simulate
References: AOI-2 "Malfunction Of The Reactor Control System" Rev.23
Task Number:: RO-085-AOI-2-004 APPLICABLE FOR: RO/SRO
IOCFR55.45: 2, 3, 4, 5, 6, 12
Validation Time: 23 min. Time Critical: No
Applicant: Time Start:
NAME SSN Time Finish:
Performance Rating: SAT UNSAT Performance Time
Examiner: /
NAME SIGNATURE DATE
COMMENTS
JPMR095A/Sim
Page 3 of 13
SIMULATOR OPERATOR INSTRUCTIONS:
1. Initialize to IC # 144.
2. Ensure Bank Step Counters at correct settings.
3. Acknowledge all alarms.
4. Freeze simulator until the performance indicates understanding of the task and time
is allowed for control board familiarization.
5. NOTE: This JPM has been preshot in IC #144. The following is the setup instructions
if needed:
Reset to IC #51
imf rd07b. Causes C-5 rod to drop.
Dilute 700 gallons
Ensure Shutdown Bank and Control Banks that are fully withdrawn have step counters
at correct setting (Simulator at 228, check K0015 which contains the current monthly
full out rod position on ICS computer).
Assign drop rod F6 (Control Bank C) to manual trigger el: imf rd07a (el)
6. Ensure CR in Manual
7. Ensure Power Range NIs at 75% or less.
8. After performer indicates understanding of task, place simulator in run.
SIMULATOR OPERATOR INSTRUCTIONS:
Ensure that malfunction to drop control rod F6 has been assigned to manual trigger el.
During performance of JPM step 12 [Step 27] "Align RCCA to affected bank position" when
control rod C-5 reaches 10 steps withdrawn, activate manual trigger 1 by:
imf itrigger or use ETM page.
JPMR095AISim
Page 4 of 13
ToolslEquipmentlProcedures Needed:
Ensure clean copy of AOI-2 in all copies of Operating Instructions on the Simulator
Floor.
READ TO OPERATOR
DIRECTION TO TRAINEE:
I will explain the initial conditions, and state the task to be performed. All control
room steps shall be performed for this JPM, including any required
communications. I will provide initiating cues and reports on other actions when
directed by you. Ensure you indicate to me when you understand your assigned
task. To indicate that you have completed your assigned task return the handout
sheet I provided you.
INITIAL CONDITIONS:
The plant was operating at 100% power when shutdown rod C-5 dropped into the core
due to a power cabinet card problem about 15 minutes ago.
AOI-2,Sect 3.3, was entered and performed through Step 16.
The problem has been repaired.
The reactor power was reduced to ___ 75% per the instruction.
Unit SRO, Shift Manager, Reactor Engineering and STA have agreed on a retrieval rate
of 64 steps per minute, and maximum power level of 100%.
You are the OAC.
INITIATING CUES:
The Unit Supervisor directs you to realign the C-5 rod starting at AOI-2, Section
3.3, Step 17.
You are to notify the Unit Supervisor when the rod is realigned with the bank.
JPMR095A/Sim
Page 5 of 13
START TIME:
STEP 1: Obtain the correct procedure.
STANDARD: A copy of AOI-2 Section 3.3 has been obtained.
EXAMINER'S CUE: After the performerhas demonstratedthe method of
obtainingthe correctinstruction, the evaluatorcan UNSAT
provide a copy of the instruction.
COMMENTS:
i
STEP 2: [Step 17] PLACE rod control in bank select position for CRITICAL
affected bank. STEP
1-RBSS is placed in the SBD position. Step is critical to SAT
STANDARD:
ensure proper bank is selected to align affected rod.
UNSAT
COMMENTS:
"**ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMR095A/Sim
Page 6 of 13
NOTE: Computer Points for individual rods are C0009A through
C0035A for shutdown banks and C0039A through C0076A for
control banks. Average rod position points are U0001 through
U001 3. Rod step position points are U0049 through U0056. All
points are in ICS "GROUP DISPLAY MENU" listed in "SPECIAL
GROUPS" as "SG 1".
STEP 3: [STEP 18] RECORD the value of the following:
"* Affected bank's step counter(s).
"* Computer step indication for rods in the affected bank. SAT
"* P/A converter for bank (N/A for Shutdown Bank) [Aux Inst
Room, el 708, 1-PNL-85-R42].
" Bank Overlap Counter (N/A for Shutdown Bank) [control rod
UNSAT
drive room, el 782, panel 1-L-122].
STANDARD: Performer determines & logs the following:
- Step counter readings for SD bank D
- Computer step indication for SD bank D.
COMMENTS:
i
NOTE: Toggle switch up is disconnected. Toggle switch down is
connected.
STEP 4: [STEP 19] DISCONNECT all lift coils in affected bank, EXCEPT CRITICAL
for dropped RCCA. STEP
STANDARD: Toggle switches in cabinet 1-XS-85-1 for rods E-13, N-1 1, & L
3 are placed in the disconnect position (up position). Step is
critical to assure proper rod is selected to be aligned and
the remaining rods are not inadvertently positioned in the
following steps.
UNSAT
COMMENTS:
"**ltalicizedCues Are To Be Used Only If JPM Performance Is Being Simulated.
JPMR095A/Sim
Page 7 of 13
NOTE: The next step will cause a CONTROL ROD URGENT FAILURE
alarm (except for Shutdown Banks C and D). Additional alarms
associated with rod position may occur due to possible errors
in the P/A converter and the computer (such as Lo-Lo Rod
insertion alarm when zeroing the P-A converter). After the rods
are aligned and the rod position is updated, then these alarms
will reset.
STEP 5: [STEP 20] INSERT affected RCCA greater than 10 steps, and
CONTINUE until NO RCCA motion is observed on RPI
STANDARD: 1-FLRM, Rod Motion Control IN-OUT stick, is used to insert rod
> 10 steps on step counter SAT
COMMENTS: UNSAT
STEP 6: [STEP 21] SET affected step counter to "000".
STANDARD: Shutdown Bank D Step counter is set at "0"
COMMENTS:
UNSAT
"**Italicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMR095A/Sim
Page 8 of 13
I
STEP 7: [STEP 22] USE Plant computer to set affected bank's
position to zero.
b. SELECT ROD BANK UPDATE SAT
c. ENTER 0 in affected bank position, THEN PRESS F3 to
save.
STANDARD: Performer uses the plant computer Rod Bank update function UNSAT
to set Shutdown Bank D Step Counter to "0".
COMMENTS:
1-
STEP 8: [STEP 23] IF dropped RCCA is in Control Bank, THEN
ADJUST the P/A converter, USING Attachment 1 [Aux Inst
Room, el 708, 1-PNL-85-R42].
STANDARD: Performer determines the rod is in shutdown bank and
proceeds to next step.
UNSAT
COMMENTS:
"**ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMR095ASim
Page 9 of 13
NOTE: Computer constant K0015 contains the current monthly full out
rod position for all rod banks.
STEP 9: [STEP 24] DETERMINE affected RCCA bank's required
position.
STANDARD: Performer reviews data from Step 18 or from computer point SAT
KOO15 or from NOB or calls Rx Engineering to determine full
out position.
- CUE: IF NOB is referenced or Reactor Engineering contacted, UNSAT
state full out position is 228 steps.
COMMENTS:
STEP 10: [STEP 25] OBTAIN approval from the Plant Manager or
designee prior to raising reactor power.
STANDARD: Performer calls Plant Manager or his designee for approval SAT
prior to increasing Reactor Power.
- CUE: When Plant Manager or his designate is contacted, grant
approval to increase power. UNSAT
COMMENTS:
- ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMR095A/Sim
Page 10 of 13
CAUTION Power level for performing recovery and maximum allowable
power level during recovery will depend on initial power,
location of dropped RCCA and duration of event.
STEP 11: [STEP 26] DO NOT CONTINUE UNTIL the following agree on
a retrieval rate, power level at which recovery will be SAT
performed and maximum power level:
"* Unit SRO.
"* Shift Manager.
"* Rx Engineering. UNSAT
"* STA.
STANDARD: Performer determines that the above personnel have agreed
to retrieval rate and maximum power level per initial
conditions.
- CUE: If any one of the above is contacted, state that the Unit
SRO, Shift Manager, Rx Engineering and STA are in
agreement to retrieve the rod at normal manual speed of
64 steps/minute. Maximum power level is 100%.
Recover from present power level.
COMMENTS:
"**ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMR095A/Sim
Page 11 of 13
NOTE Step 27 RNO does not apply if alignment stopped due to
turbine load reaching maximum established in Step 26.
Step 28 will reduce turbine load and allow alignment to
continue.
STEP 12: [STEP 27] ALIGN RCCA to affected bank position:.
"* USE rod control to position affected RCCA to bank position SAT
determined in Step 24.
"* RAISE turbine load to maintain T-avg and T-ref within 30 F.
UNSAT
STANDARD: Performer attempts to realign the rod by placing 1-FLRM to
the OUT position AND determines that the rod is withdrawing.
Performer stops withdrawing rod after recognizing another rod
has dropped into core.
- CUE: If requested then CRO will control turbine load to
maintain T-avg and T-ref within 30 F.
NOTE TO EVALUATOR When rod has been withdrawn 10 steps the
console operator will drop control rod F6 in
control bank C. The operator may immediately
stop withdrawing rod, announce that a second rod
has dropped, and then trip the reactor before
referring to AOI-2 Section 3.3.
COMMENTS:
"**Italicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMR095A/Sim
Page 12 of 13
NOTE TO EVALUATOR: Following steps are from the beginning of Section
3.3 in AOI-2 due to another dropped rod.
STEP 13: [STEP 1] PLACE control rods in MAN.
STANDARD: Control Rods are in MAN position. No action required.
NOTE TO EVALUATOR: Rod control is in SBD position.
UNSAT
COMMENTS:
STEP 14: [STEP 2] IF two or more RCCAs have dropped THEN: CRITICAL
a. TRIP reactor. STEP
b. **GO TO E-0, Reactor Trip or Safety Injection.
STANDARD: Reactor Trip hand switch on 1-M-4 or 1-M-6 has been placed
to the TRIP position. Performer than goes to E-0. SAT
Step is critical to task performance as two dropped
control rods requires reactor trip.
UNSAT
- CUE: When performer transitions to E-O, inform himlher that
the JPM is complete "WE'LL STOP HERE".
COMMENTS:
END OF TASK I
TIME STOP:
"**Italicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Page 13 of 13
APPLICANT CUE SHEET
(TO BE RETURNED TO EXAMINER UPON COMPLETION OF TASK)
DIRECTION TO TRAINEE:
I will explain the initial conditions, and state the task to be performed. All control
room steps shall be performed for this JPM, including any required
communications. I will provide initiating cues and reports on other actions when
directed by you. Ensure you indicate to me when you understand your assigned
task. To indicate that you have completed your assigned task return the handout
sheet I provided you.
INITIAL CONDITIONS:
The plant was operating at 100% power when shutdown rod C-5 dropped into the core
due to a power cabinet card problem about 15 minutes ago.
AOI-2,Sect 3.3, was entered and performed through Step 16.
The problem has been repaired.
The reactor power was reduced to < 75% per the instruction.
Unit SRO, Shift Manager, Reactor Engineering and STA have agreed on a retrieval rate
of 64 steps per minute, and maximum power level of 100%.
You are the OAC.
INITIATING CUES:
The Unit Supervisor directs you to realign the C-5 rod starting at AOI-2, Section
3.3, Step 17.
You are to notify the Unit Supervisor when the rod is realigned with the bank.
J PMA047/Local
Page 1 of 11
REGION II
INITIAL LICENSE EXAMINATION
B.2.a JPMA047/Local
LOCAL CONTROL OF SG LEVELS (AFWT A-S) PER
SOI-3.02
APPLICANT
EXAMINER
JPMA047/Local
Page 2 of 11
REGION II
INITIAL LICENSE EXAMINATION
Task: LOCAL CONTROL OF SG LEVELS (AFWT A-S) PER SOI-3.02.
Alternate Path: N/A
Facility JPM #: 3-OT-JPMA047 Rev 4
K/A Rating(s): 061A3.03 [4.2/4.2] 055EA2.01 [3.4/3.7] 055EK3.02 [403/4.6]
2.1.20 [4.3/4.2] 2.2.25 [2.5/3.7] 2.1.30 [3.913.4]
Task Standard: 1-FCV-3-173 and 1-FCV-3-172 are located and positioned per SOI-3.02.
Preferred Evaluation Location: Preferred Evaluation Method:
Simulator In-Plant X Perform Simulate X
References: SOI-3.02 "Auxiliary Feedwater System" Rev. 29
Task Number:: AUO-003-SOI-3.02-014 APPLICABLE FOR: AUO/RO/SRO
IOCFR55.45: 7, 8, 9
Validation Time: 10 min. Time Critical: No
Applicant: Time Start:
NAME SSN Time Finish:
Performance Rating: SAT UNSAT Performance Time
Examiner: /
NAME SIGNATURE DATE
COMMENTS
JPMA047/Local
Page 3 of 11
Tools/EquipmentlProcedures Needed:
Hard Hat, Safety Glasses, Flashlight, Hearing Protection, and Plant Approved Shoes.
Latest revision of SOI-3.02.
ALARA considerations.
NOTE: START THIS JPM AT THE RAD WASTE DESK.
Provide copy of SOI-3.02 Section 8.5 with Applicant's Cue Sheet.
READ TO OPERATOR
DIRECTION TO TRAINEE:
I will explain the initial conditions, and state the task to be performed. All control
room steps shall be performed for this JPM, including any required
communications. I will provide initiating cues and reports on other actions when
directed by you. Ensure you indicate to me when you understand your assigned
task. To indicate that you have completed your assigned task return the handout
sheet I provided you.
INITIAL CONDITIONS:
The unit has tripped from 100% power.
A loss of all AC power has occurred.
The Turbine Driven Aux. Feed Pump is running and on recirc.
All Control Air pressure (essential and non-essential) is decreasing and the TD AFW
pump LCVs have closed.
You are the Aux. Bldg. AUO
INITIATING CUES:
You have been dispatched by the CRO to take local control of valves I-LCV-3-173
and 1-LCV-3-172 per SOI-3.02 Section 8.5 (#2 and #3 SIG LCVs from the TD AFW
pump) with directions to manually open each valve approximately 50%.
You are to inform the operator after both valves are positioned.
JPMA047/Local
Page 4 of 11
START TIME:
STEP 1: Obtain a copy of the instruction.
STANDARD: A copy of S01-3.02 Section 8.5.3 has been obtained.
EXAMINER'S CUE: Provide performer copy of Section 8.5.3 from SOI
3.02. UNSAT
COMMENTS:
-I
NOTE TO EVALUATOR The following is not a procedure step but is
included as a procedure note preceding the
procedure section in effect. Simulate obtaining
radio.
NOTE Direct radio communication with UO required to perform this
section.
I
STEP 2: Establish communication with the UO.
STANDARD: Radio Communication with the MCR has been established. SAT
- CUE: Role play as the MCR I UO, acknowledge report using
repeat back. UNSAT
COMMENTS:
I _____________________________
- ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMA047/Local
Page 5 of 11
Note: The following step was given in the initial conditions and may be
omitted by the performer.
STEP 3: [Step 1] ENSURE TD AFW PUMP A-S running.
STANDARD: Performer determines TD AFW Pump A-S is running. This SAT
information was supplied in the initial conditions.
- CUE: If a TDAFWP parameter is checked, state the condition to UNSAT
indicate that the Turbine Driven pump is running.
(Given in initial conditions)
COMMENTS:
Note: The performer may elect to position one valve at a time or may
perform steps on both valves simultaneously.
STEP 4: [Step 2] IF MANUAL control of SG 1 level is necessary,
THEN PERFORM the following to fail CLOSED 1-LCV-3-174, TD
AFW PUMP SG 1 LEVEL CONTROL {S. Vlv Rm]:
[a] CLOSE 1-ISV-32-3736, ESSENT CONTROL AIR ISOL VALVE SAT
TO 1-LCV-3-174.
[b] DEPRESSURIZE air from regulator on 1-LCV-3-174.
STANDARD: Performer determines that this step does not apply. UNSAT
COMMENTS:
- ltalicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMA047/Local
Page 6 of 11
STEP 5: [Step 3] MODULATE flow with handwheel on top of 1-LCV
3-174 (CLOCKWISE to OPEN) per UO instruction.
STANDARD: Performer determines that this step does not apply. SAT
UNSAT
COMMENTS:
STEP 6: [Step 4] IF MANUAL control of SG 2 level is necessary, CRITICAL
THEN PERFORM the following to fail CLOSED 1-LCV-3-173, STEP
TD AFW PUMP SG 2 LEVEL CONTROL [A3U/737 Pen. Rm]:
[a] CLOSE 1-ISV-32-3735, ESSENT CONTROL AIR ISOL VALVE
TO 1-LCV-3-173. SAT
[b] DEPRESSURIZE air from regulator on 1-LCV-3-173.
STANDARD: The control air supply to 1-LCV-3-173 has been isolated by
UNSAT
closing 1-ISV-32-3735, and the petcock on the regulator
opened to release any air pressure remaining.
Step is critical to isolate air from the diaphragm to fail
valve closed and ensure it is vented.
- CUE: After air supply valve handwheel is rotated in the
clockwise direction, state that the handwheel rotates
several turns and gets snug.
- CUE: After air supply is isolated and the petcock on the
regulator is opened, state that the air is initially heard/felt
coming from the petcock then slows down and stops.)
COMMENTS:
I _________________________
"**Italicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
J PMA047/Local
Page 7 of 11
STEP 7: [Step 5] MODULATE flow with handwheel on top of 1-LCV CRITICAL
3-173 (CLOCKWISE to OPEN) per UO instruction. STEP
STANDARD: The hand wheel on 1-LCV-3-173 has been rotated in the SAT
CLOCKWISE direction to open the valve zý50% by local
indication.
Step is critical to manually position valve to supply UNSAT
- CUE: If the hand wheel is turned counterclockwise, state that
the hand wheel will NOT move.
- CUE: If the hand wheel is turned clockwise, state that the hand
wheel rotates.
- CUE: If the valve stem is checked, state it indicates
approximately 50% open.
COMMENTS:
"**Italicized Cues Are To Be Used Only 1f JPM PerformanceIs Being Simulated.
JPMA047/Local
Page 8 of 11
I
STEP 8: [Step 6] IF MANUAL control of SG 3 level is necessary, CRITICAL
THEN PERFORM the following to fail CLOSED 1-LCV-3-172, STEP
TD AFW PUMP SG 3 LEVEL CONTROL [A3U/737 Pen. Rm]:
[a] CLOSE 1-ISV-32-3770, ESSENT CONTROL AIR ISOL VALVE
TO 1-LCV-3-172. SAT
[b] DEPRESSURIZE air from regulator on 1-LCV-3-172.
STANDARD: The control air supply to 1-LCV-3-172 has been isolated by
closing 1-ISV-32-3770, and the petcock on the regulator UNSAT
opened to release any air pressure remaining.
Step is critical to isolate air from the diaphragm to fail
valve closed and ensure it is vented.
- CUE: After air supply valve hand wheel is rotated in the
clockwise direction, state that the hand wheel rotates
several turns and gets snug.
- CUE: After air supply is isolated and the petcock on the
regulator is opened, state that the air is initially heard/felt
coming from the petcock then slows down and stops.
COMMENTS:
- ItalicizedCues Are To Be Used Only If JPM Performance Is Being Simulated.
JPMA047/Local
Page 9 of 11
STEP 9: [Step 7] MODULATE flow with handwheel on top of 1-LCV CRITICAL
3-172 (CLOCKWISE to OPEN) per UO instruction. STEP
STANDARD: The hand wheel on 1-LCV-3-172 has been rotated in the
CLOCKWISE direction to open the valve = 50% by local SAT
indication.
Step is critical to manually position valve to supply
- CUE: If the hand wheel is turned counterclockwise, state that
the hand wheel will NOT move.
- CUE: If the hand wheel is turned clockwise, state that the hand
wheel rotates.
- CUE: If the valve stem is checked, state it indicates
approximately 50% open.
COMMENTS:
STEP 10: [Step 8] IF MANUAL control of SG 4 level is necessary,
THEN PERFORM the following to fail CLOSED 1-LCV-3-175,
TD AFW PUMP SG 3 LEVEL CONTROL [S. Viv Rm]:
[a] CLOSE 1-ISV-32-3769, ESSENT CONTROL AIR ISOL VALVE
TO 1-LCV-3-175.
[b] DEPRESSURIZE air from regulator on 1-LCV-3-175. SAT
STANDARD: The performer determines that this step does not apply.
COMMENTS: UNSAT
- ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMA047/Local
Page 10 of 11
STEP 11: [Step 9] MODULATE flow with handwheel on top of 1-LCV
3-175 (CLOCKWISE to OPEN) per UO instruction.
STANDARD: The performer determines that this step does not apply.
COMMENTS:
UNSAT
4
STEP 12: Inform the CRO that 1-LCV-3-172 and 1-LCV-3-173 have
been manually positioned to 50% open.
STANDARD: The CRO is contacted and informed that 1-LCV-3-172 and 1 SAT
LCV-3-173 have been manually positioned to 50% open.
- CUE: When the CRO is contacted, repeat back and then
terminate the JPM by telling the performer, "Rad Waste UNSAT
AUO will take over control of LCVs 3-172 and 173. We'll
stop here".
COMMENTS:
END OF TASK
I _____________________________________________________
TIME STOP:
"**ltalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Page 11 of 11
APPLICANT CUE SHEET
(TO BE RETURNED TO EXAMINER UPON COMPLETION OF TASK)
DIRECTION TO TRAINEE:
I will explain the initial conditions, and state the task to be performed. All control
room steps shall be performed for this JPM, including any required
communications. I will provide initiating cues and reports on other actions when
directed by you. Ensure you indicate to me when you understand your assigned
task. To indicate that you have completed your assigned task return the handout
sheet I provided you.
INITIAL CONDITIONS:
The unit has tripped from 100% power.
A loss of all AC power has occurred.
The Turbine Driven Aux. Feed Pump is running and on recirc.
All Control Air pressure (essential and non-essential) is decreasing and the TD AFW
pump LCVs have closed.
You are the Aux. Bldg. AUO
INITIATING CUES:
You have been dispatched by the CRO to take local control of valves 1 -LCV-3-173
and 1-LCV-3-172 per SOI-3.02 Section 8.5 (#2 and #3 SIG LCVs from the TD AFW
pump) with directions to manually open each valve approximately 50%.
You are to inform the operator after both valves are positioned.
JPMA44AILocal
Page 1 of 13
REGION I!
INITIAL LICENSE EXAMINATION
B.2.b JPMA044A/Local
ALIGNMENT UPPER CONTAINMENT MONITOR TO
THE LOWER CONTAINMENT LOCALLY
APPLICANT
EXAMINER
JPMA44A/Local
Page 2 of 13
REGION Ii
INITIAL LICENSE EXAMINATION
Task: Alignment Upper Containment Monitor To The Lower Containment Locally
Alternate Path: N/A
Facility JPM #: 3-OT-JPMA044A Rev 2
K/A Rating(s): 002K4.05 [3.8/4.2] 029K1.02 [3.3/3.6] 002A3.01 [3.7/3.91
Task Standard: 1-RM-90-112 is located, and valves are aligned and 1-RM-90-112 is sampling the
lower containment per SOI-90.02 Section 8.1
Preferred Evaluation Location: Preferred Evaluation Method:
Simulator In-Plant X Perform Simulate X
References: SOI-90.02 "Gaseous Process Radiation Monitors" Rev. 11
Task Number:: AUO-090-SOI-90.2-005 APPLICABLE FOR: AUO/RO/SRO
10CFR55.45: 9
Validation Time: 15 min. Time Critical: No
Applicant: Time Start:
NAME SSN Time Finish:
Performance Rating: SAT _ UNSAT Performance Time
Examiner: /
NAME SIGNATURE DATE
COMMENTS
JPMA44A/Local
Page 3 of 13
Tools/Equipment/Procedures Needed:
Hard Hat, Safety Glasses, Flashlight, Hearing Protection, and Plant Approved Shoes.
Latest revision of SOI-90.02.
ALARA considerations.
READ TO OPERATOR
DIRECTION TO TRAINEE:
I will explain the initial conditions, and state the task to be performed. All control
room steps shall be performed for this JPM, including any required
communications. I will provide initiating cues and reports on other actions when
directed by you. Ensure you indicate to me when you understand your assigned
task. To indicate that you have completed your assigned task return the handout
sheet I provided you.
INITIAL CONDITIONS:
Unit One is at 10 % power following a startup.
1-RM-90-106 "Lower Containment Air Monitor" and 1-RM-90-112 "Upper Containment
Air Monitor" were aligned and were sampling their respective containments (normal
alignment).
1-RM-90-106 has tripped, neither sample pump could be restarted, and monitor was
shutdown per the appropriate procedure.
You are the Auxiliary Bldg AUO.
INITIATING CUES:
You have been directed by the Operator At Controls to align 1-RM-90-112 to
sample lower containment.
You are to notify the MCR operator when you have completed this alignment.
JPMA44A/Local
Page 4 of 13
START TIME:
I1
i
STEP 1: Obtain a copy of the appropriate instruction
STANDARD: A copy of SOI-90.02 Section 8.1 has been obtained
EXAMINER'S CUE: After the performer identifies correct instruction, the UNSAT
evaluator can provide a copy of the instruction.
COMMENTS:
7
NOTE If any Radiation Monitor experiences sufficient elevated
reading above normal request MIG to perform purge.
Cue: If asked, or MCR contacted, state Radiation Monitors are
reading normal.
I
STEP 2: [Step 1] ENSURE Upper Containment Air Monitor Aligned
per Section 5.2.
STANDARD: The performer determines that Upper Containment Air Monitor
is aligned normal per task assignment sheet.
UNSAT
- CUE: IF asked, state that Section S01-90.02 Section 5.2 has
been completed and the Upper Containment Monitor is
sampling Upper Containment.
COMMENTS:
"**ltalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
J PMA44A/Local
Page 5 of 13
I
STEP 3: [Step 2] NOTIFY Chem lab of intent to realign monitors so
that proper sampling of Cntmt. and release permits are
addressed.
STANDARD: The performer notifies Chem Lab of the intent to realign upper
containment monitor 1-RM-90-112 to the lower containment.
UNSAT
- CUE: Respond as Chem Lab, using repeat back to the
notification as stated by the performer.
COMMENTS:
STEP 4: [Step 3] SHUTDOWN Lower Containment Air Monitor per
Section 7.1.
STANDARD: The performer determines that lower containment air monitor
1-RM-90-106 has been shut down based on task assignment
sheet.
UNSAT
- CUE: Respond as OAC if contacted, using repeat back that
SOI-90.02 Section 7.1 has been completed for the lower
containment monitor.
COMMENTS:
"**ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMA44A/Local
Page 6 of 13
CRITICAL
STEP 5: [Step 4] ENSURE 1-RE-90-106 and 1-RE-90-112 pumps are
OFF before aligning monitor. CRITICAL
STEP
STANDARD: The performer locally checks90-106 and 90-112 monitor
sample pumps and turns off the running sample pump on the
1-90-RM-1 12 monitor (switch above monitor cabinet). SAT
Step is critical prevent burn-up of sample pump during
valve alignments to follow.
UNSAT
NOTE TO EVALUATOR: Underlined portion above is critical portion of
this step.
- CUE: IF asked and when checked, state the following for
respective monitor:
- RM-106 sample pumps "off" green light is LIT and
both handswitch stop pushbuttons are IN
- RM-1 12, sample pump 11 2A in service red "on" light
is LIT and sample pump 112B green "off" light is LIT.
State sample pump for 11 2A green light is LIT and red
light is OFF when running pumps handswitch STOP
pushbutton is depressed.)
COMMENTS:
t
STEP 6: [Step 5] RECORD the monitor sample pump STOPPED (N/A
pump NOT stopped)
[a] 1-HS-90-112A
[b] 1-HS-90-112B SAT
STANDARD: The performer records the sample pump stopped in the
previous step I -HS-90-112A for the A pump. UNSAT
COMMENTS:
"**ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMA44A/Local
Page 7 of 13
Evaluator Note: JPM steps 7, 8, and 9 are part of the same procedure step,
can be performed in any order. I
I
STEP 7: [STEP 6] PERFORM THE FOLLOWING: CRITICAL
NOMENCLATURE STEP
LOCATION POSITION UNID
LOWER CONTAINMENT SUP A3U1737 OPEN 1-ISIV-90-112A
TO 1-RE-90-112 CROSS TIE
STANDARD: Performer locates 1-ISIV-90-112A and rotates hand wheel SAT
counter clockwise until valve is fully open. (Valve located
above monitor)
Step is critical align to upper containment monitor to lower UNSAT
containment.
- CUE: After performer indicates how to open the valve, state
that the valve handle rotated several turns in the counter
clockwise direction and stops.
COMMENTS:
i __________________________
"**Italicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMA44A/Local
Page 8 of 13
STEP 8: [STEP 6] PERFORM THE FOLLOWING: CRITICAL
STEP
NOMENCLATURE LOCATION POSITION UNID
CNTMT TO RM-106 CIV-CVI 0-M-12 CLOSED 1-HS-90-110
INSIDE CNTMT
CNTMT TO RM-106 CIV-CVI 0-M-12 CLOSED 1-HS-90-111
OUTSIDE CNTMT
CNTMT TO RM-112 CIV-CVI 0-M-12 CLOSED 1-HS-90-113
OUTSIDE CNTMT
CNTMT TO RM-112 CIV-CVI 0-M-12 CLOSED 1-HS-90-114
INSIDE CNTMT
CNTMT TO RM-112 CIV-CVI 0-M-12 CLOSED 1-HS-90-115
INSIDE CNTMT I
STANDARD: Performer contacts the control room and has the above valves SAT
positioned to the CLOSED position. Valves90-113, 90-114,90-115 are closed and verified closed by communication with
the control room. Valves90-110 & 111 are verified closed by
communication with the control room. UNSAT
Step is critical to ensure proper flow path from lower
containment to the upper containment monitor.
NOTE TO EVALUATOR: Underlined portion above is only portion that is
critical.
- CUE: Respond as the MCR when contacted, using proper
communication technique and then state that 1-HS-90
110 & 111 hand switches were already closed, 1-HS-90
113, 114, & 115 hand switches have been placed to the
CLOSED position.
COMMENTS:
- Italicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated
J PMA44A/Local
Page 9 of 13
7
STEP 9: [STEP 6] PERFORM THE FOLLOWING: CRITICAL
STEP
NOMENCLATURE LOCATION POSITION UNID
CNTMT TO RM-1 12 CIV-CVI 0-M-12 OPEN 1-HS-90-116
INSIDE CNTMT
CNTMT TO RM-112 CIV-CVI 0-M-12 OPEN 1-HS-90-117
OUTSIDE CNTMT
CNTMT TO RM-106 CIV-CVI 0-M-12 OPEN 1-HS-90-107
OUTSIDE CNTMT
CNTMT TO RM-106 CIV-CVI 0-M-12 OPEN 1-HS-90-108
INSIDE CNTMT
CNTMT TO RM-106 CIV-CVI 0-M-12 OPEN 1-HS-90-109
INSIDE CNTMT II
STANDARD: Performer contacts the control room and has the above valves SAT
positioned to the OPEN position. Valves90-116, 90-117 are
opened and verified open by communication with MCR. Valves90-107, 90-108, & 90-109 are verified open by communication
with control room. UNSAT
Step is critical to ensure proper flow path from lower
containment to the upper containment monitor.
NOTE TO EVALUATOR: Underlined portion above is only portion that is
critical.
- CUE: Respond as the MCR when contacted, using proper
communication technique and then state that I -HS-90-116
& 117 hand switches have been placed to the OPEN
position.
- CUE: Respond as the MCR when contacted, using proper
communication technique and state 1-HS-90-107, 108, &
109 hand switches were already in the OPEN position.
COMMENTS:
- Italicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMA44A/Local
Page 10 of 13
STEP 10: [STEP 7] START the monitor sample pump STOPPED in Step CRITICAL
[5] (N/A pump NOT started): STEP
[a] 1-HS-90-112A
[b] 1-HS-90-112B
STANDARD: The performer starts the proper sample pump that was
shutdown earlier using 1-HS-90-112A for the A pump..
Step is critical to establish flow from lower containment to UNSAT
the upper containment monitor.
- CUE: When performer indicated how pump is started and if
asked state sample pump for 112A red "on" light is LIT
and green "off" light is OFF. Supply the following if/when
asked:
I-FI-90-112A indicates t 12 SCFM,
1-FI-90-112C indicates z 2.1 SCFM,
I -PI-90-1 12B indicates 2" vacuum,
I -PI-90-112A indicates 4" vacuum,
Iodine Low Flow red alarm light is LIT
COMMENTS:
I
STEP 11: [STEP 8] IF IODINE LOW FLOW ALARM on skid comes in,
THEN RESET with 1-HS-90-112JB.
STANDARD: The performer resets the iodine low flow alarm with 1-HS-90
112JB.
- CUE: When asked and when checked, State that Iodine Low UNSAT
Flow red light is LIT.
- CUE: When asked, State that light turns off when performer
operates 1-HS-90-112JB to reset.
COMMENTS:
- ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMA44A/Local
rage II of 13
STEP 12: [STEP 9] PERFORM MONITOR SOURCE CHECK [0-M-12],
and ENSURE 1-RM-90-112 green OPERATE Light LIT and red
HIGH & yellow ALERT Lights NOT LIT.,
ENSURE ANN 173-A UPR CNTMT AIR 1-RM-112 RAD HI, NOT
LIT.
ENSURE ANN 173-D UPR CNTMT AIR 1-RM-1 12 INSTR
MALF, NOT LIT.
UNSAT
STANDARD: Performer contacts the control room to have the 90-112
monitor source checked and verifies that green operate light is
LIT and High & Alert light are NOT LIT and ANNs windows
173-A and 173-D are NOT LIT.
- CUE: Respond as the MCR when contacted using proper
communication technique, then state:
v monitor source check was successful
- green OPERATE light is LIT
- High & Alert lights for monitor are NOT LIT
- ANN windows 173-A & 173-D are NOT LIT.
COMMENTS:
I-
STEP 13: [STEP 10] ENSURE Local Panel Lights RESET
STANDARD: SAT
The performer verifies that Filter Failure light is NOT LIT,
verifies that the Particulate LOW Flow Light is NOT LIT,
verifies that the Iodine LOW flow Light is NOT LIT.
- CUE: If asked and when checked, state that UNSAT
"* Iodine Low Flow light is NOT LIT (If Iodine low flow
was not reset in JPM step 11 step [8], this light will be
LIT)
"* Particulate Low flow light is NOT LIT
"* Filter Fail light is NOT LIT
COMMENTS:
I_____________________________
"**ltalicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMA44A/Local
Page 12 of 13
STEP 14: Notify Operator At Controls that Upper Containment Monitor
has been aligned to Lower Containment.
STANDARD: The performer contacts the control room and reports that the
Upper Containment Monitor is aligned to Lower Containment.
- CUE: When notified, acknowledge the report using "repeat
back"
UNSAT
COMMENTS:
END OF TASK
i ____________________________________________________
TIME STOP:
"**ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Page 13 of 13
APPLICANT CUE SHEET
(TO BE RETURNED TO EXAMINER UPON COMPLETION OF TASK)
DIRECTION TO TRAINEE:
I will explain the initial conditions, and state the task to be performed. All control
room steps shall be performed for this JPM, including any required
communications. I will provide initiating cues and reports on other actions when
directed by you. Ensure you indicate to me when you understand your assigned
task. To indicate that you have completed your assigned task return the handout
sheet I provided you.
INITIAL CONDITIONS:
Unit One is at 10 % power following a startup.
1-RM-90-106 "Lower Containment Air Monitor" and 1-RM-90-112 "Upper Containment
Air Monitor" were aligned and were sampling their respective containments (normal
alignment).
1-RM-90-106 has tripped, neither sample pump could be restarted, and monitor was
shutdown per the appropriate procedure.
You are the Auxiliary Bldg AUO.
INITIATING CUES:
You have been directed by the Operator At Controls to align 1-RM-90-112 to
sample lower containment.
You are to notify the MCR operator when you have completed this alignment.
JPMA098/Local
Page 1 of 8
REGION I!
INITIAL LICENSE EXAMINATION
B.2.c JPMA098/Local
ALIGNMENT OF ERCW TO 1A-A CCP LUBE OIL HEAT
EXCHANGER PER AOI-15
APPLICANT
EXAMINER
JPMA098/Local
Page 2 of 8
REGION II
INITIAL LICENSE EXAMINATION
Task: ALIGNMENT OF ERCW TO 1A-A CCP LUBE OIL HEAT EXCHANGER PER AO-1i5
Alternate Path: N/A
Facility JPM #: 3-OT-JPMA098 Rev 3
K/A Rating(s): 026AA1.03 [3.6/3.6] 2.1.30 [3.9/3.4]
Task Standard: ERCW is aligned to the lA-A CCP per AOl-15, Attachment I within 12 minutes.
Preferred Evaluation Location: Preferred Evaluation Method:
Simulator In-Plant X Perform Simulate X
References: AOI-15 "Loss Of Component Cooling Water (CCS)" Rev.18
Task Number:: RO-070-AOI-15-003 APPLICABLE FOR: AUO/RO/SRO
AUO-067-AOI-15-001
1OCFR55.45: 8, 9, 10
REQUIRED COMPLETION Time: 12 min. Time Critical: YES
Applicant: Time Start:
NAME SSN Time Finish:
Performance Rating: SAT UNSAT Performance Time
Examiner: /
NAME SIGNATURE DATE
COMMENTS
JPMA098ILocal
Page 3 of 8
Tools/Equipment/Procedures Needed:
Hard Hat, Safety Glasses, Flashlight, Hearing Protection, and Plant Approved Shoes.
AO1-1 5 Attachment 1 (Latest revision)
Auxiliary Building Entry Under RWP.
Ladder Safety since some valves require access from above floor elevation, and
ALARA considerations.
NOTE: Start this JPM at the Rad Waste AUO Desk EL 692.
NOTE: Hand Attachment 1of AO1-15 to the performer with their handout
sheet
READ TO OPERATOR
DIRECTION TO TRAINEE:
I will explain the initial conditions, and state the task to be performed. All control
room steps shall be performed for this JPM, including any required
communications. I will provide initiating cues and reports on other actions when
directed by you. Ensure you indicate to me when you understand your assigned
task. To indicate that you have completed your assigned task return the handout
sheet I provided you.
INITIAL CONDITIONS:
The unit has experienced a loss of Train A Component Cooling Water.
The 1A-A CCP is in service and is the only available charging pump.
You are an AUO on shift.
INITIATING CUES:
You have been instructed by the Unit Operator to align ERCW to the 1A-A CCP
lube oil heat exchanger per Attachment 1 of AOl-15.
You are to notify the Unit Operator when the appendix is complete.
THIS IS A TIME CRITICAL JPM.
JPMA098/Local
Page 4 of 8
START TIME:
CAUTION: CCP may survive for only 10 to 12 minutes after loss of CCS
to lube oil cooler.
NOTE: All valves are located in CCP 1A-A room, except for 1-ISV-67
602A, CVCS CCP ROOM CLR 1A ERCW RET ISOL which is
outside the room [A4T/692]
-I-
STEP 1: [STEP 1] CLOSE 1-ISV-67-602A, CVCS CCP ROOM CLR
CRITICAL
STEP
STANDARD: 1-ISV-67-602A is closed by pulling the orange handle 90'.
(perpendicular to the pipe).
Step is critical to isolate flow path from cooler to ERCW
return header.
UNSAT
EXAMINER'S CUE: After the performer has demonstrated the method of
closing the valve, state that the valve handle is
perpendicular to the pipe.
COMMENTS:
4
STEP 2: [Step 2] CLOSE 1-ISV-70-553A, CCP1A-A OIL COOLERS CRITICAL
CCS INLET ISOLATION. STEP
STANDARD: 1-ISV-70-553A is closed by rotating the valve hand wheel
clockwise.
Step is critical to isolate flow path to CCS Supply header.
UNSAT
- CUE: After the performer has demonstrated the method of
closing the valve, state that the valve travels several
turns in the clockwise direction and stops.
COMMENTS:
I ______________________________
"**Italicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMA098/Local
Page 5 of 8
STEP 3: [STEP 3] CLOSE 1-THV-70-554A, CCP1A-A OIL COOLERS CRITICAL
CCS OUTLET THROTTLE. STEP
STANDARD: 1-THV-70-554A is closed by rotating the valve hand wheel
clockwise.
Step is critical to isolate flow path to CCS Return header.
- CUE: After the performer has demonstrated the method of
closing the valve, state that the valve travels several UNSAT
turns in the clockwise direction and stops.
COMMENTS:
STEP 4: [STEP 4] CLOSE 1-DRV-67-1017B, CCP OIL CLR ERCW CRITICAL
SUP XTIE HDR DRAIN. STEP
STANDARD: 1-DRV-67-1017B is closed by rotating the valve hand wheel SAT
clockwise.
Step is critical to isolate flow path from ERCW supply
drain to enable ERCW to be aligned to supply oil cooler. UNSAT
- CUE: After the performer has demonstrated the method of
closing the valve, state that the valve travels several
turns in the clockwise direction and stops.
COMMENTS:
"**ltalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMA098/Local
Page 6 of 8
Note To Evaluator: Performance Steps 5 through 7 are all part of the
same Attachment steD.
STEP 5: [STEP 5] ESTABLISH ERCW flow to lube oil cooler: CRITICAL
a. OPEN 1-ISV-67-1015B, CCP OIL CLR ERCW SUP XTIE STEP
ISOL.
STANDARD: 1-ISV-67-1015B is opened by rotating the valve hand wheel
counter-clockwise.
Step is critical to provide flow path from ERCW to CCP. UNSAT
- CUE: After the performer has demonstrated the method of
opening the valve, state that the valve travels several
turns in the counter-clockwise direction and stops.
COMMENTS:
I
STEP 6: b. OPEN 1-ISV-67-1016B, CCP OIL CLR ERCW SUP XTIE CRITICAL
ISOL. STEP
STANDARD: 1-ISV-67-1016B is opened by rotating the valve hand wheel SAT
counter-clockwise.
Step is critical to supply ECRW flow path to CCP Lube Oil
Cooler. UNSAT
- CUE: After the performer has demonstrated the method of
opening the valve, state that the valve travels several
turns in the counter-clockwise direction and stops.
COMMENTS:
.1______________________________________
"*ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMA098/Local
Page 7 of 8
STEP 7: c. OPEN 1-DRV-70-782A, CCP 1A-A OIL COOLERS CCS CRITICAL
OUTLET DRAIN to establish ERCW flow to oil coolers. STEP
STANDARD: 1-DRV-70-782A is opened by rotating the valve hand wheel
counter-clockwise.
Step is critical to provide flow path from CCP Lube Oil
Cooler to floor drain. UNSAT
- CUE: After the performer has demonstrated the method of
opening the valve, state that the valve travels several
turns in the counter-clockwise direction and stops.
- CUE: If asked, water is gushing into the floor drain from the
hose connected to the line.
NOTE TO EVALUATOR: NOTE TIME VALVE SIMULATED OPEN
COMMENTS:
STEP 8: Notify the Unit Operator that the Attachment 1 of AOl-1 5 is
complete.
STANDARD: The Unit is notified that the Attachment 1 is complete.
- CUE: When notified, acknowledge the report using repeat SAT
back.
COMMENTS: UNSAT
END OF TASK
I_________________________
TIME STOP:
"**Italicized Cues Are To Be Used Only lf JPM PerformanceIs Being Simulated.
Page 8 of 8
CANDIDATE CUE SHEET
(TO BE RETURNED TO EXAMINER UPON COMPLETION OF TASK)
DIRECTION TO TRAINEE:
I will explain the initial conditions, and state the task to be performed. All control
room steps shall be performed for this JPM, including any required
communications. I will provide initiating cues and reports on other actions when
directed by you. Ensure you indicate to me when you understand your assigned
task. To indicate that you have completed your assigned task return the handout
sheet I provided you.
INITIAL CONDITIONS:
The unit has experienced a loss of Train A Component Cooling Water.
The 1A-A CCP is in service and is the only available charging pump.
You are an AUO on shift.
INITIATING CUES:
You have been instructed by the Unit Operator to align ERCW to the 1A-A CCP
lube oil heat exchanger per Attachment I of AOl-1 5.
You are to notify the Unit Operator when the appendix is complete.
THIS IS A TIME CRITICAL JPM.
JPMRADMIN A.1.a
Page 1 of 6
REGION II
INITIAL LICENSE EXAMINATION
ADMINISTRATIVE JOB PERFORMANCE MEASURE
A.l.a JPMRADMIN
DETERMINE MAIN TURBINE ROLL AND LOADING
RATES USING SOI-47.02 GRAPHS
APPLICANT
EXAMINER
JPMRADMIN A.1.a
Page 2 of 6
REGION II
INITIAL LICENSE EXAMINATION
ADMINISTRATIVE JOB PERFORMANCE MEASURE
Task: DETERMINE MAIN TURBINE ROLL AND LOADING RATES USING SOI-47.02 GRAPHS
Alternate Path: N/A
Facility JPM #: New
K/A Rating(s): 2.1.25 [2.8/3.1]
Task Standard: Time for roll of main turbine to synch speed and loading rates are determined
based upon initial HP 1 st stage metal temperature.
References: SOI-47.02 "Turbo-Generator Startup Operation" Rev. 23
Task Number:: RO-047-SOI-47-003 APPLICABLE FOR: RO/SRO
RO-047-SOI-47-003
IOCFR55.45: 5, 6
Validation Time: min. Time Critical: No
Applicant: Time Start:
NAME SSN Time Finish:
Performance Rating: SAT UNSAT Performance Time
Examiner: I
NAME SIGNATURE DATE
COMMENTS
JPMRADMIN A.l.a
Page 3 of 6
Tools/Equipment/Procedures Needed:
Latest revision of SOI-47.02.
Ruler or straight edge.
Calculator
NOTE: START THIS JPM AT A LOCATION WHERE PERFORMER HAS ACCESS
TO PROCEDURES (Simulator, Main Control Room, TIC or provide
performer with procedure).
READ TO OPERATOR
DIRECTION TO TRAINEE:
I will explain the initial conditions, and state the administrative task to be
performed. I will provide initiating cues and reports on other actions when
directed by you. Ensure you indicate to me when you understand your assigned
task. To indicate that you have completed your assigned task return the handout
sheet I provided you.
INITIAL CONDITIONS:
The Main Turbine-generator had been shut down 12 hours1.388889e-4 days <br />0.00333 hours <br />1.984127e-5 weeks <br />4.566e-6 months <br /> ago to perform a repair of
an EHC oil leak that has been subsequently repaired.
Main Turbine roll and turbo-generator loading is scheduled as the next activity.
The CRO is performing SOI-47.02, TURBO-GENERATOR STARTUP OPERATION.
Turbine IMPULSE CHAMBER METAL temp [1-TR-47-2, ptl] is 150OF
You are the CRO.
INITIATING CUES:
Using Appendix C of SOI 47.02 perform the following:
"* Determine the turbine maximum acceleration rate and minimum time allowed by
procedure to bring main turbine to sync speed.
"* Determine the minimum length of time that turbine load must held at 5%.
"* Determine the minimum time allowed by procedure to increase load to 100% after
completion of the 5% hold. Assume no other restrictions on loading rate.
- Write and circle answer at bottom of graph.
JPMRADMIN A.l.a
Page 4 of 6
START TIME:
STEP 1: Obtain a copy of the instruction.
STANDARD: A copy of SOI-47.02 has been obtained.
EXAMINER'S CUE: After the performer identified correct instruction, the
evaluator can provide a copy of the instruction. UNSAT
COMMENTS:
+
STEP 2: Determine the turbine acceleration rate and minimum time
allowed by procedure to bring main turbine to sync speed.
STANDARD: Using Appendix C of SOI-47.02 for 150 0 F, the performer
determines that minimum time to reach synch speed is 0.75 (+
0.1) hrs ( or 45 +/-6) minutes. Acceleration rate
1800rpm/44.2min = 40 (34 - 46) rpm/minute. UNSAT
COMMENTS:
"**ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMRADMIN A.1.a
Page 5 of 6
STEP 3: Determine the minimum length of time that turbine load must
held at 5%.
STANDARD: Using Appendix C of SOI-47.02 for 1500 F, the performer
determines that minimum time to hold turbine generator at
minimum load is 0.875 (+/- 0.125) hrs (or 52.5 +/- 7.5) minutes.
UNSAT
COMMENTS:
STEP 4: Determine the minimum time allowed by procedure to increase
load to 100% after completion of the 5% hold. Assume no
other restrictions on loading rate.
STANDARD: Using Appendix C of SOI-47.02 for 150 0 F, the performer UNSAT
determines that it will take 2.625 (+/- 0.2) additional hours to
reach 100% load (157.5 +/- 7.5 minutes). Assuming 5% initial
load to 100% load to take 157.5 +/- 7.5 minutes.
COMMENTS:
END OF TASK
END OF TAS
TIME STOP:
"**ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Page 6 of 6
APPLICANT CUE SHEET
(TO BE RETURNED TO EXAMINER UPON COMPLETION OF TASK)
DIRECTION TO TRAINEE:
I will explain the initial conditions, and state the administrative task to be
performed. I will provide initiating cues and reports on other actions when
directed by you. Ensure you indicate to me when you understand your assigned
task. To indicate that you have completed your assigned task return the handout
sheet I provided you.
INITIAL CONDITIONS:
The Main Turbine-generator had been shut down 12 hours1.388889e-4 days <br />0.00333 hours <br />1.984127e-5 weeks <br />4.566e-6 months <br /> ago to perform a repair of
an EHC oil leak that has been subsequently repaired.
Main Turbine roll and turbo-generator loading is scheduled as the next activity.
The CRO is performing SOI-47.02, TURBO-GENERATOR STARTUP OPERATION.
Turbine IMPULSE CHAMBER METAL temp [1-TR-47-2, ptl] is 150 0 F
You are the CRO.
INITIATING CUES:
"* Determine the turbine acceleration rate and minimum time allowed by procedure
to bring main turbine to sync speed.
"* Determine the minimum length of time that turbine load must held at 5%.
"* Determine the minimum time allowed by procedure to increase load to 100% after
completion of the 5% hold. Assume no other restrictions on loading rate.
JPMRADMIN A.1.a
Page 2 of 6
REGION II
INITIAL LICENSE EXAMINATION
ADMINISTRATIVE JOB PERFORMANCE MEASURE
Task: DETERMINE MAIN TURBINE ROLL AND LOADING RATES USING SOI-47.02 GRAPHS
Alternate Path: N/A
Facility JPM #: New
K/A Rating(s): 2.1.25 [2.8/3.1]
Task Standard: Time for roll of main turbine to synch speed and loading rates are determined
based upon initial HP 1 st stage metal temperature.
References: SOI-47.02 "Turbo-Generator Startup Operation" Rev. 25
Task Number:: RO-047-SOI-47-003 APPLICABLE FOR: RO/SRO
RO-047-SOI-47-003
1OCFR55.45: 5, 6
Validation Time: min. Time Critical: No
Applicant: Time Start:
NAME SSN Time Finish:
Performance Rating: SAT UNSAT _ Performance Time _
Examiner:
NAME SIGNATURE DATE
COMMENTS
WBN TURBO-GENERATOR STARTUP OPERATION SOI-47.02
I Revision 25
Page 57 of 73
APPENDIX C
Page 1 of 1
TURBINE STARTUP CURVE
4APPLY INMAL LOAO =S% 10[*I-410% 1,4- 2w/.
0)
r:
w
LuJ
0
°F INITIAL HP 1ST-STAGE METAL TEMP
WBN TURBO-GENERATOR STARTUP OPERATION SOI-47.02
I Revision 25
Page 57 of 73
APPENDIX C
Page 1 of 1
TURBINE STARTUP CURVE
H-APPLY INMAL LOAD 5% .~~410% b }4- 20%-).
I
4.C
H
0)
c:
3.5 6
0
. INCREASE -
uJ LOAD
w 64 pzý
2.
F:
1.0 ,,, -*X \
"0~
0. ACCELERATE TO
SYNC SPEED
50 100 1,=0 200 250 300 350 400 450 500T
Q Ao0 -t 4L'- U
0
o L~$
JPMRADMIN A.l.b
Page 1 of 8
REGION II
INITIAL LICENSE EXAMINATION
ADMINISTRATIVE JOB PERFORMANCE MEASURE
A.l.b JPMRADMIN
OBTAIN AND VERIFY CONTROLLED PROCEDURE
COPY USING CURATOR
APPLICANT
EXAMINER
JPMRADMIN A.1.b
Page 2 of 8
REGION II
INITIAL LICENSE EXAMINATION
ADMINISTRATIVE JOB PERFORMANCE MEASURE
Task: OBTAIN AND VERIFY CONTROLLED PROCEDURE COPY USING CURATOR
Alternate Path: N/A
Facility JPM #: New
K/A Rating(s): 2.1.21 [3.1/3.2]
Task Standard: Verify for use a controlled procedure copy using CURATOR.
References: SPP-2.3 "Document Control" Rev. 4 Section 3.11 and 3.12.
Task Number:: AUO-1 19-SSP-2.55-004 APPLICABLE FOR: AUO/RO/SRO
10CFR55.45:
Validation Time: min. Time Critical: No
Applicant: Time Start:
NAME SSN Time Finish:
Performance Rating: SAT UNSAT Performance Time
Examiner: /
NAME SIGNATURE DATE
COMMENTS
JPMRADMIN A. 1.b
Page 3 of 8
ToolslEquipment/Procedures Needed:
Access to computer that has Curator (FYI) that can produce hard copies of documents.
NOTE: START THIS JPM AT A LOCATION WHERE PERFORMER HAS ACCESS
TO COMPUTER THAT HAS CURATOR ACCESS TO WBN. (Main Control
Room, TIC or Shift Clerk's Office, Tagging Office, Classroom.).
NOTE TO EVALUATOR: If curator (FYI) program is presently open or minimized, have
the performer exit the program before assigning the task. At the completion of the task,
have the performer exit curator (FYI) program.
NOTE TO EVALUATOR: This JPM should be given in conjunction with Sim 3 JPMR168.
READ TO OPERATOR
DIRECTION TO TRAINEE:
I will explain the initial conditions, and state the administrative task to be
performed. I will provide initiating cues and reports on other actions when
directed by you. Ensure you indicate to me when you understand your assigned
task. To indicate that you have completed your assigned task return the handout
sheet I provided you.
INITIAL CONDITIONS:
The Unit is at 100% rated thermal power.
S01-65.02 "Emergency Gas Treatment System" is scheduled to be performed later in
the current shift.
You are the CRO.
INITIATING CUES:
- The Unit Supervisor has directed you to obtain a copy of SOI-65.02 from
CURATOR.
0 Inform the Unit Supervisor when you have obtained this copy.
JPMRADMIN A.1.b
Page 4 of 8
START TIME:
STEP 1: Locate a computer that has access to CURATOR.
STANDARD: Performer locates computer that has access to CURATOR.
COMMENTS: UNSAT
STEP 2: Open CURATOR software program and access WBN's Curator
files.
STANDARD: Performer selects the "FYI" icon and opens program, selects
WBNFYI Prod and enters OK Performer enters Login ID and
password.
UNSAT
NOTE TO EVALUATOR: Login ID can also be LOOKUP or GUEST,
Password can also be LOOKUP or GUEST.
COMMENTS:
"**ltalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMRADMIN A.l.b
Page 5 of 8
STEP 3: Select procedure general from Search Class List to obtain
Search Screen.
STANDARD: Performer Selects PROCEDURE GENERAL from the search
class list by selecting it (i.e., highlighting it) with mouse, then
either double click mouse or use forward arrow at top of file.
UNSAT
COMMENTS:
STEP 4: Enter procedure number into search screen in the Procedure
Number field.
STANDARD: Performer enters SOI-65.02 into procedure number field of the
search screen and then depresses enter key or clicks on
forward arrow. Performer may enter SOl into the procedure
type field and select advance, then scroll until procedure found. UNSAT
Performer may enter a combination of letters into the
procedure title field (i.e., CONTAIN "EMERGENCY" or "GAS"
etc.).
COMMENTS:
- ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMRADMIN A.1.b
Page 6 of 8
STEP 5: Selects procedure SOI-65.02 from the document list and opens
document.
STANDARD: SAT
Performer advances to next step Folder Screen and selects
SOI-65.02 and advances to document screen and then
advances to open document.
UNSAT
NOTE TO EVALUATOR: Document will open in the appropriate format
for viewing. (WORD or IMAGENATION).
COMMENTS:
4-
STEP 6: Print a copy of SOI-65.02, retrieve copy from printer.
STANDARD: Performer simulates printing a copy of SOI-65.02. SAT
EVALUATOR CUE: Simulate what you would do to print the document.
NOTE TO EVALUATOR: Do not allow print of document. -UNSAT
COMMENTS:
.1. ___________________________
"**Italicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMRADMIN A.1 .b
Page 7 of 8
STEP 7: Inform Unit Supervisor that a copy of SOI-65.02 has been
obtained from CURATOR.
STANDARD: Performer Informs Unit Supervisor that a copy of SOI-65.02
has been obtained from CURATOR. UNSAT
- CUE: Acknowledge report as Unit Supervisor using repeat
back.
- CUE: Have applicant close all windows opened and exit from
curator.
COMMENTS:
END OF TASK
TIME STOP:
"**ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Page 8 of 8
APPLICANT CUE SHEET
(TO BE RETURNED TO EXAMINER UPON COMPLETION OF TASK)
DIRECTION TO TRAINEE:
I will explain the initial conditions, and state the administrative task to be
performed. I will provide initiating cues and reports on other actions when
directed by you. Ensure you indicate to me when you understand your assigned
task. To indicate that you have completed your assigned task return the handout
sheet I provided you.
INITIAL CONDITIONS:
The Unit is at 100% rated thermal power.
SOI-65.02 "Emergency Gas Treatment System" is scheduled to be performed later in
the current shift.
You are the CRO.
INITIATING CUES:
- The Unit Supervisor has directed you to obtain a copy of SOI-65.02 from
CURATOR.
0 Inform the Unit Supervisor when you have obtained this copy.
JPMRADMIN A.2
Page 1 of 12
REGION II
INITIAL LICENSE EXAMINATION
ADMINISTRATIVE JOB PERFORMANCE MEASURE
A.2 JPMRADMIN
CALCULATE QPTR USING 1-SI-0-21
APPLICANT
EXAMINER
JPMRADMIN A.2
Page 2 of 12
REGION II
INITIAL LICENSE EXAMINATION
ADMINISTRATIVE JOB PERFORMANCE MEASURE
Task: CALCULATE QPTR USING 1-SI-0-21
Alternate Path: N/A
Facility JPM #: New
K/A Rating(s): 2.1.12 [2.9/4.0]
Task Standard: Quadrant Power Tilt Ratio has been determined per 1-SI-0-21 Section 6.1 and
Attachment 1. Acceptance criteria are determined to be not met due for N-42
Lower Detector and N-44 Upper Detector.
Preferred Evaluation Location: Preferred Evaluation Method:
Simulator X In-Plant Perform X Simulate
References: 1-SI-0-21 "Excore QPTR & Axial Flux Difference" Rev. 11; Nuclear Operating
Book (NOB) A-2 Sheet 1-3 Rev 38, A-2 Sheet 4 Rev 36.
Task Number:: RO-092-Sl-2-001 APLICABLE FOR: RO/SRO
I OCFR55.45:
Validation Time: 13 min. Time Critical: No
Applicant: Time Start:
NAME SSN Time Finish:
Performance Rating: SAT UNSAT Performance Time
Examiner: /
NAME SIGNATURE DATE
COMMENTS
JPMRADMIN A.2
Page 3 of 12
Tools/EquipmentiProcedures Needed:
Applicant Data Sheet
Latest revision of 1-SI-0-21
Latest revision of NOB Sheets A-2 (all four PR detector channels)
Calculator
NOTE: START THIS JPM AT A LOCATION WHERE PERFORMER HAS ACCESS
TO PROCEDURES (Simulator, Main Control Room, TIC, etc.).
NOTE TO EVALUATOR: Hand out the Applicant Data Sheet along with the Applicant's
Cue Sheet.
READ TO OPERATOR
DIRECTION TO TRAINEE:
I will explain the initial conditions, and state the administrative task to be
performed. I will provide initiating cues and reports on other actions when
directed by you. Ensure you indicate to me when you understand your assigned
task. To indicate that you have completed your assigned task return the handout
sheet I provided you.
INITIAL CONDITIONS:
The unit is operating at 100% rated thermal power
AFD Monitor Alarm and QPTR alarms are out of service due to card problem in the
annunciator system.
1-SI-0-21 "Excore QPTR & Axial Flux Difference SI is required to be performed every
12 hours1.388889e-4 days <br />0.00333 hours <br />1.984127e-5 weeks <br />4.566e-6 months <br /> since both QPTR alarms are inoperable.
Plant computer is not available for performing this SI.
You are a support CRO.
INITIATING CUES:
" Given the data that was just obtained from each power range channel upper and
lower detector currents, the Unit Supervisor directs you to perform Section 6.1
"Excore QPTR Determination" of 1-SI-0-21. M&TE will not be utilized for data
measurements.
"* Report the results to the Unit Supervisor when Attachment I and Section 6.1 have
been completed.
JPMRADMIN A.2
Page 4 of 12
START TIME:
STEP 1: Obtain a copy of the instruction.
STANDARD: A copy of 1-SI-0-21 has been obtained.
EXAMINER'S CUE: After the performer identified correct instruction, the
evaluator can provide a copy of the instruction. UNSAT
COMMENTS:
NOTE TO EVALUATOR: The following steps are from Section 6.1 of 1-SI
0-21
NOTE I Obtaining QPTR calculated values from the Process Computer
is the preferred method to check that the QPTR is within
Technical Specification limits. QPTR values are obtained from
Process Computer calculated computer points for upper and
lower radial flux tilt. These points are available on the "Tilting
Factors" display. The report may be printed with turn on code
TFREP.
NOTE 2 Up to one inoperable excore channel can be marked NIA if
THERMAL POWER is < 75% RTP.
STEP 2: [Step 1] IF the process Computer is available, THEN PRINT the
Tilting Factors Report AND/OR PERFORM the QPTR
calculations using Attachment 1.
STANDARD: Performer goes to attachment 1 and commences performance
of attachment 1.
UNSAT
COMMENTS:
"**ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMRADMIN A.2
Page 5 of 12
NOTE TO EVALUATOR: The following steps are from Attachment I of 1
SI-0-21
NOTE I Determining detector currents by measuring the voltage i
across the detector's meter test points, using DVM, is the
most accurate method for measuring QPTR and for
determining the validity of a QPTR alarm.
NOTE 2 Using detector current meter readings is another method to
quickly check that QPTR is within limits. These meters are not
as accurate as the DVM readings and may produce
unacceptable results because: 1) the meters on the 'B' drawer
may be scaled too high or (2) the meter may be unstable due
to drift or noise. When unacceptable results are obtained DVM
readings should be obtained, otherwise, Step [1] and [2] may
be marked NIA if DVM not used.
NOTE 3 Up to one inoperable excore channel can be marked NIA if
THERMAL POWER is < 75% RTP.
STEP 3: [Step 1] RECORD DVM information:
B. Cal Due Date:
STANDARD: Performer determine step in N/A based on initial conditions for
task performance and proceeds to the next step.
UNSAT
COMMENTS:
I
STEP 4: [Step 2] ENSURE require M&TE is within its current calibration.
STANDARD: Performer determines step is N/A based on initial conditions for
task performance and proceeds to the next step.
UNSAT
COMMENTS:
I. _________________________
- ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMRADMIN A.2
Page 6 of 12
NOTE The following determination may be made by measuring the
voltage across the 1000 ohm precision resistor in NIS power
range drawer B. When using this method the Ohm's Law
conversion from a millivolt measurement to a microamp
measurement only requires changing the unit designator (e.g.,
280 millivolts converts to 280 microamps.
CAUTION An inadvetent reactor trip may be prevented by ensuring
that no power range neutron high flux rate or power range
high flux channels are in the tripped condition prior to
taking EACH measurement in the NIS Power Range Drawer
B.
STEP 4: [Step 3] DETERMINE the microamps for each upper and lower
excore detector on each NIS power range drawer B, AND
RECORD below:
UPPER DETECTOR LOWER DETECTOR
NIS Channel It Detector Current lb Detector Current
(microamps) (microamps)
N-41A (369) (384)
N-42A (368) (386)
N-43A (369) (385)
N-44A (371) (386)
STANDARD: Performer obtains the detector current microamp readings from SAT
the handout given during task assignment and enters the
appropriate data into Attachment 1 step 3.
NOTE TO EVALUATOR: Values above in ( ) are detector currents from UNSAT
handout.
COMMENTS:
"**ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMRADMIN A.2
Page 7 of 12
NOTE: Rt and Rb (detector calibration data) changes periodically
throughout the cycle. Current values are on NOB Sheet A-2, NIS
Calibration Data.
STEP 5: [Step 4] OBTAIN and RECORD current values of Rt and Rb
(volts/microamps).
UPPER DETECTOR LOWER DETECTOR
NIS Channel Rt (volts/microamps) Rb (volts/microamps)
N-41A (0.0360) (0.0347)
N-42A (0.0374) (0.0370)
N-43A (0.0360) (0.0342)
N-44A (0.0402) (0.0356)
STANDARD: Performer obtains the detector current values from NOB SAT
Sheets A-2 for the respective NIS Power Range Detectors and
records them in appropriate blocks on Attachment 1 Step 4.
NOTE TO EVALUATOR: Values above in ( ) are detector currents from UNSAT
respective NOB Sheets A-2.
COMMENTS:
"**Italicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMRADMIN A.2
Page 8 of 12
STEP 6: [Step 5] CALCULATE calibrated output voltages by multiplying the
uncalibrated detector output currents by Rt or Rb (as
applicable).
A. Vt=ItxRt
B. Vb= lbx Rb
UPPER DETECTOR LOWER DETECTOR
NIS Channel Vt Calib. Output Vb Calib. Output
Voltage Voltage
N-41A (369) (0.0360)=13.284 (384) (0.0347)=13.325
N-42A (368) (0.0374)=13.763 (386) (0.0370)=14.282
N-43A (369) (0.0360)=13.284 (385) (0.0342)=13.167
N-44A (371) (0.0402)=14.914 (386) (0.0356)=13.742
STANDARD: Performer calculates the calibrated output voltages [Step 3] by SAT
multiplying the respective detector's current reading times
resistance values [step 4] and records the results in
appropriate blocks on Attachment 1 Step 5.
UNSAT
COMMENTS:
4
STEP 7: [Step 6] CALCULATE average calibrated output voltage for the
upper and lower detectors.
UPPER Vt LOWER Vb
AVERAGE (13.284+13.763+13.284+1 (13.325+14.282+13.167+1
4.914)/4 = 13.811 3.742)/4 = 13.629
STANDARD: Performer calculates the average output voltages for the upper SAT
detector by adding the respective upper detector's calibrated
output voltage readings [from Step 5] and dividing the result
by the number of channels in service. This process is repeated
for the lower detector using the lower detector calibrated UNSAT
voltages. The results recorded in appropriate blocks on
Attachment 1 Step 6.
COMMENTS:
"**ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMRADMIN A.2
Page 9 of 12
STEP 8: [Step 7] CALCULATE QPTR values by dividing each detector's
(upper or lower) Calibration Output Voltage by the average
(upper or lower) Calibrated Output Voltage.
A. QPTRt Vt÷ Avg Vt
B. QPTRb =Vb x Avg Vb
UPPER LOWER
DETECTOR DETECTOR
NIS Channel QPTRt Value QPTRb Value
N-41A (13.284/13.81 1)= 0.962 (13.325/13.629)= 0.978
N-42A (13.763/13.81 1)= 0.997 (14.282/13.629)= 1.048
N-43A (13.284/13.811)= 0.962 (13.167/13.629)= 0.966
N-44A (14.914/13.811)= 1.080 (13.742/13.629)= 1.008
STANDARD: Performer calculates QPTR values by dividing the respective SAT
Calibrated Output Voltage [ from step 5] by the Average
Calibrated Output Voltage for each NIS channel detector
[from step 6]. The results recorded in appropriate blocks on
Attachment 1. Performer returns to Section 6.1 Step 7. UNSAT
COMMENTS:
NOTE TO EVALUATOR The following steps are from Section 6.1 of 1
Sl-0-21. I
STEP 9: [Step 2] REVIEW the Upper and Lower QPTR values.
STANDARD: Performer reviews QPTR values from Attachment 1 Step 7. SAT
COMMENTS:
UNSAT
I_____________________________
"**Italicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMRADMIN A.2
c ukjuV~
STEP 10: [Step 3] CHECK (') Acceptance Criteria.
ACCEPTANCE CRITERIA: All operable excore channels
(upper and lower) indicate a QPTR < 1.02. SAT
YES NO
STANDARD: Performer determines that N-42 Lower Detector and N-44A UNSAT
Upper Detector exceed 1.02 QPTR. Performer then checks
NO statement.
COMMENTS:
STEP 11: Inform the Unit Supervisor that Attachment 1 and Section 6.1
of 1-SI-0-21 has been completed and the results of the QPTR.
STANDARD: Performer inform the Unit Supervisor of the completion of
Attachment 1 and Section 6.1 of 1-SI-0-21 and reports that
acceptance criteria have not been satisfied. QPTR for N-42
Lower Detector is 1.047 and for N-44 Upper detector is 1.079 UNSAT
which exceed QPTR limit of 1.02.
EXAMINER'S CUE: Acknowledge report as Unit Supervisor, then state
We will stop here.
COMMENTS:
END OF TASK
TIME STOP:
"**ltalicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Page 11 of 12
APPLICANT CUE SHEET
(TO BE RETURNED TO EXAMINER UPON COMPLETION OF TASK)
DIRECTION TO TRAINEE:
I will explain the initial conditions, and state the administrative task to be
performed. I will provide initiating cues and reports on other actions when
directed by you. Ensure you indicate to me when you understand your assigned
task. To indicate that you have completed your assigned task return the handout
sheet I provided you.
INITIAL CONDITIONS:
The unit is operating at 100% rated thermal power
AFD Monitor Alarm and QPTR alarms are out of service due to card problem in the
annunciator system.
1-SI-0-21 "Excore QPTR & Axial Flux Difference SI is required to be performed every
12 hours1.388889e-4 days <br />0.00333 hours <br />1.984127e-5 weeks <br />4.566e-6 months <br /> since both QPTR alarms are inoperable.
Plant computer is not available for performing this SI.
You are a support CRO.
INITIATING CUES:
" Given the data that was just obtained from each power range channel upper and
lower detector currents, the Unit Supervisor directs you to perform Section 6.1
"Excore QPTR Determination" of 1-SI-0-21. M&TE will not be utilized for data
measurements.
"* Report the results to the Unit Supervisor when Attachment 1 and Section 6.1 have
been completed.
Page 12 of 12
APPLICANT DATA SHEET
(TO BE RETURNED TO EXAMINER UPON COMPLETION OF TASK)
The following microampere readings were taken from the Power Range
NIS detectors:
UPPER DETECTOR LOWER DETECTOR
NIS Channel It Detector Current IbDetector Current
(microamps) (microamps)
N-41A 369 384
N-42A 368 386
N-43A 369 385
N-44A 371 386
JPMRADMIN A.3
Page 1 of 8
REGION !1
INITIAL LICENSE EXAMINATION
ADMINISTRATIVE JOB PERFORMANCE MEASURE
A.3 JPMRADMIN
DETERMINE IF PERSONNEL WILL EXCEED
ADMINISTRATIVE DOSE LIMITS WHILE
PERFORMING TASK
APPLICANT
EXAMINER
JPMRADMIN A.3
Page 2 of 8
REGION I!
INITIAL LICENSE EXAMINATION
ADMINISTRATIVE JOB PERFORMANCE MEASURE
Task: DETERMINE IF PERSONNEL WILL EXCEED ADMINISTRATIVE DOSE LIMITS WHILE
PERFORMING TASK
Alternate Path: N/A
Facility JPM #: New
K/A Rating(s): 2.3.10 [2.9/3.3]
Task Standard: Performer determines that path from additional equipment building results in the
lowest dose, and that the remaining allowable dose is not exceeded.
Preferred Evaluation Location: Preferred Evaluation Method:
Simulator In-Plant Perform X Simulate
References:
Task Number:: AUO-119-SSP-5.01-001 APLICABLE FOR: AUO/RO/SRO
10CFR55.45: 10
Validation Time: 10 min. Time Critical: No
Applicant: Time Start:
NAME SSN Time Finish:
Performance Rating: SAT _ UNSAT Performance Time
Examiner: /
NAME SIGNATURE DATE
COMMENTS
JPMRADMIN A.3
Page 3 of 8
Tools/Equipment/Procedures Needed:
Calculator
NOTE TO EVALUATOR: Hand out the Applicant Data Sheet along with the Applicant's
Cue Sheet.
READ TO OPERATOR
DIRECTION TO TRAINEE:
I will explain the initial conditions, and state the administrative task to be
performed. I will provide initiating cues and reports on other actions when
directed by you. Ensure you indicate to me when you understand your assigned
task. To indicate that you have completed your assigned task return the handout
sheet I provided you.
INITIAL CONDITIONS:
The unit had experienced a valid safety injection signal.
The unit had also experienced a loss of both Unit 1 shutdown boards and RCP Seal
Injection and thermal barrier cooling have been isolated per ECA-0.0 Appendix "A".
The unit has also experienced fuel damage.
Shutdown Board 1A has been re-energized and control room dispatches you to locally
start 1A TBBP and throttle open the discharge valve.
A survey map is available for elevation 737 of the auxiliary building, showing dose
rates and travel times to reach the TBBP Discharge valve that you will throttle open.
Three AUO's are available for assignment to perform this task.
RADCON personnel are currently unavailable to provide assistance.
INITIATING CUES:
You have been directed to determine the AUO (s) that could perform task without
exceeding administrative limits:
"* AUO #1 has TEDE of 625 mRem
"* AUO #2 has TEDE of 675 mRem
"* AUO #3 has TEDE of 725 mRem
JPMRADMIN A.3
Page 4 of 8
START TIME:
NOTE TO EVALUATOR: The following steps may be performed out of
order.
I
STEP 1: Calculate Exposure during pump start and throttle valve
operation. SAT
STANDARD: (2 R/hr)(1000MR/R)(1HRI60Min)(5 Min) = 166.67 MR
EXAMINER'S CUE: After the performer identified correct instruction, the UNSAT
evaluator can provide a copy of the instruction.
COMMENTS:
i
STEP 2: Calculate the exposure getting to task area and return.
STANDARD: Dose received for 2 way travel for survey area "B" are added to SAT
dose received in Survey Area "A":
1) (3 R/hr)(1000MR/R)(1HR/60Min)(4 Min) = 200 MR
COMMENTS: UNSAT
1-
STEP 3: Calculate total dose for job.
STANDARD: Dose received for 2 way travel for survey area "B" are added to SAT
dose received in Survey Area "A":
1) Two way Survey Area B = 200 MR
2) Dose in Survey Area A = 166.67 MR
3) Total Dose = 200 MR + 166.67 MR = 366.67 MR UNSAT
COMMENTS:
- ltalicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
JPMRADMIN A.3
IJnc ~£-%j~I1
- C ,u Q
STEP 5: Determine total dose that would be received for all AUO.s
involved.
STANDARD: Performer Determines dose that would be received by AUO's.
1) AUO #1: 625 mrem + 366.67 mrem = 991.67 mrem
2) AUO #2: 675 mrem + 366.67 mrem = 1041.67 mrem
3) AUO #3: 725 mrem + 366.67 mrem = 1091.67 mrem UNSAT
COMMENTS:
I
STEP 5: Determines which AUO can perform tasks without exceeding
Administrative limits.
STANDARD: Performer determines AUO #1 is the only AUO that could
perform task.
COMMENTS: UNSAT
END OF TASK I _________________________________________________
TIME STOP:
- ltalicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Page 6 of 8
APPLICANT CUE SHEET
(TO BE RETURNED TO EXAMINER UPON COMPLETION OF TASK)
DIRECTION TO TRAINEE:
I will explain the initial conditions, and state the administrative task to be
performed. I will provide initiating cues and reports on other actions when
directed by you. Ensure you indicate to me when you understand your assigned
task. To indicate that you have completed your assigned task return the handout
sheet I provided you.
INITIAL CONDITIONS:
The unit had experienced a valid safety injection signal.
The unit had also experienced a loss of both Unit 1 shutdown boards and RCP Seal
Injection and thermal barrier cooling have been isolated per ECA-0.0 Appendix "A".
The unit has also experienced fuel damage.
Shutdown Board 1A has been re-energized and control room dispatches you to locally
start 1A TBBP and throttle open the discharge valve.
A survey map is available for elevation 737 of the auxiliary building, showing dose
rates and travel times to reach the TBBP Discharge valve that you will throttle open.
Three AUO's are available for assignment to perform this task.
RADCON personnel are currently unavailable to provide assistance.
INITIATING CUES:
You have been directed to determine the AUO (s) that could perform task without
exceeding administrative limits:
"* AUO #1 has TEDE of 625 mRem
"* AUO #2 has TEDE of 675 mRem
"* AUO #3 has TEDE of 725 mRem
Page 7 of 8
APPLICANT DATA SHEET
(TO BE RETURNED TO EXAMINER UPON COMPLETION OF TASK)
SURVEY DATA:
"* TBBP control switches and pump discharge FCV are located in Survey area "A".
"* Estimated time at control switch and discharge valve is 5 minutes.
"* Travel time to Valve & control switches is 2 minutes.
"* General Area Dose rate for Survey Area "A" is 2 R/hr.
"* General Area Dose rate for Survey Area "B"is 3 R/hr.
RESULTS:
Indicate below by checking yes or no if the respective AUO can be
allowed to perform task without exceeding administrative dose limits.
YES NO
AUO #1 11
D1
AUO #2 El 11
AUO #3 El El
Page 8 of 8
APPLICANT DATA SHEET
(TO BE RETURNED TO EXAMINER UPON COMPLETION OF TASK)
AUXILIARY BLDG ELEV. 737 G/A
I1
0
I
1. U/2 Heating & Ventilation Room
2. U/2 Vent & Purge Air Room
3. U/2 Gross Failed Fuel Detector Room
4. Spent Fuel Pool Equipment Area
5. U/1 Letdown Heat Exchanger Room
6. U/2 Letdown Heat Exchanger Room
7. U/i1 Gross Failed Fuel Detector Room
8. U/1 Vent & Purge Air Room
9. U/1 Heating & Ventilation Room
10. Hot Instrument Shop
11. Component Cooling Heat Exchangers
JPMRADMIN A.4 RO
Page 1 of 8
REGION II
INITIAL LICENSE EXAMINATION
ADMINISTRATIVE JOB PERFORMANCE MEASURE
A.4.RO JPMRADMIN
RESPOND TO A MEDICAL EMERGENCY IN
ACCORDANCE WITH EPIP-10
APPLICANT
EXAMINER
JPMRADMIN A.4 RO
Page 2 of 8
REGION 11
INITIAL LICENSE EXAMINATION
ADMINISTRATIVE JOB PERFORMANCE MEASURE
Task: DETERMINE CRITICAL SAFETY FUNCTION STATUS TREES WITH SPDS UNAVAILABLE.
Alternate Path: N/A
Facility JPM #: New
K/A Rating(s): 2.4.39 [3.3/3.1]
Task Standard: Performer performs actions of Appendix A of EPIP-10, "Medical Emergency
Response".
Preferred Evaluation Location: Preferred Evaluation Method:
Simulator X In-Plant Perform X Simulate
References: EPIP-10, "Medical Emergency Response", Rev. 12.
Task Number: RO-100-SOI-100-011 APPLICABLE FOR: RO/SRO
10CFR55.45: 11
Validation Time: min. Time Critical: No
Applicant: Time Start:
NAME SSN Time Finish:
Performance Rating: SAT UNSAT Performance Time
Examiner: /
NAME SIGNATURE DATE
COMMENTS
JPMRADMIN A.4 RO
Page 3 of 8
SIMULATOR OPERATOR INSTRUCTIONS:
This JPM may be performed either on the simulator or in another location. If performed
on the simulator refer to the following.
1. Initialize to any IC.
2. Acknowledge all alarms.
3. Freeze simulator for duration of task performance.
5. NOTE: This JPM may be performed using a console booth instructor who acts as
personnel outside the main control room. Cues may be made by him as indicated by
the JPM.
SIMULATOR OPERATOR INSTRUCTIONS:
When directed by the evaluator, place phone call to the "Horsehoe" to initiate the medical
emergency:
Call the "Horseshoe" and state the following:
"I want to report a medical emergency."
JPMRADMIN A.4 RO
Page 4 of 8
ToolslEquipment/Procedures Needed:
Latest revision of EPIP-10
NOTE: START THIS JPM AT A LOCATION WHERE PERFORMER HAS ACCESS
TO PROCEDURES (Simulator, Main Control Room, TIC or provide
performer with procedure).
READ TO OPERATOR
DIRECTION TO TRAINEE:
I will explain the initial conditions, and state the administrative task to be
performed. I will provide initiating cues and reports on other actions when
directed by you. Ensure you indicate to me when you understand your assigned
task. To indicate that you have completed your assigned task return the handout
sheet I provided you.
INITIAL CONDITIONS:
You are the Control Room Operator (CRO) on shift.
You have received a telephone call reporting an onsite medical emergency.
INITIATING CUES:
0 Respond to the medical emergency in accordance with EPIP-IO.
JPMRADMIN A.4 RO
Page 5 of 8
START TIME:
STEP 1: Obtain a copy of the instruction.
STANDARD: A copy of EPIP-10 has been obtained.
EXAMINER'S CUE: After the performer locates and obtains correct
instruction, the evaluator can provide a copy of the UNSAT
instruction.
COMMENTS:
NOTE TO EVALUATOR: The following steps are from EPIP-10,
Appendix A
I
STEP 2: [Step A] Obtain NAME of caller.
STANDARD: CRO requests name of caller and records on Appendix A. SAT
CUE: State to the performer that your name is John Doe.
UNSAT
COMMENTS:
Page 6 of 8
STEP 3: [Step B] LOCATION of caller.
STANDARD: Performer requests the location of the caller and records on SAT
Appendix A.
CUE: State to the performer that you are just south of the station
air compressors on elevation 685' in the Turbine Building. UNSAT
COMMENTS:
STEP 4: [Step C] Type of Medical Emergency.
STANDARD: Performer requests the type of Medical Emergency and SAT
records on Appendix A.
CUE: State to the performer that you found a male victim lying
on the floor unconscious but has heartbeat and is. UNSAT
breathing.
COMMENTS:
4-
STEP 5: [Step D] Number of personnel Involved.
STANDARD: Performer requests how many people involved and records on SAT
Appendix A.
CUE: State to the performer: "no other individuals are involved".
UNSAT
COMMENTS:
JPMRADMIN A.4 RO
Page 7 of 8
STEP 6: [Step E] Immediate Area Hazards (Radiological, Safety).
STANDARD: Requests if immediate hazards exist and records on SAT
Appendix A.
CUE: State to the performer: "no hazards exist in the area".
UNSAT
COMMENTS:
-I-
STEP 7: [Step F] Telephone number of the caller.
STANDARD: Request the telephone number of the caller and records on SAT
Appendix A.
CUE: State to the performer that the phone number of the phone
you are calling from is 5555. UNSAT
COMMENTS:
1-
STEP 8: [Step G] ALERT and DISPATCH MERT PERSONNEL
STANDARD: Performer alerts and dispatches MERT personnel. SAT
CUE: As MERT personnel, acknowledge performer's
communication.
UNSAT
COMMENTS:
JPMRADMIN A.4 RO
P$n Rnf $R
Piap A nf
STEP 9: [Step H] Make the following plant announcement with public
address:
"ATTENTION ALL SITE PERSONNEL."
"ATTENTION ALL SITE PERSONNEL."
"A MEDICAL emergency has been reported. The MERT is
to ACTIVATE and RESPOND to the following LOCATION:
STANDARD: Performer makes public address announcement and has
MERT respond to Turbine Building elevation 685', just south of
the station air compressors.
EXAMINER'S CUE: If NOT being performed on the simulator, do NOT
allow performer to actually perform this announcement.
Ensure it is simulated.
COMMENTS:
-4
STEP 10: [Step I] CONFIRM that the Shift Manager (SM) has been notified.
STANDARD: Performer ensures the SM has been notified. (may make
phone call or announce to the control crew that a medical
emergency is in progress)
- CUE: Acknowledge report as Shift Manager.
COMMENTS:
JPMRADMIN A.4 RO
P~qn-icP n-f A~
STEP 11: [Step J] CONFIRM that the Fire Protection Section Duty Shift
Supervisor (Fire Brigade Leader) was notified by:
Radio or
Telephone (extension 3311 or 3355) or __SAT
Pocket Pager 40566
UNSAT
STANDARD: Performer ensures the Fire Protection Section Duty Shift
Supervisor was notified by either radio, telephone, or pocket
pager.
EXAMINER'S CUE: Do NOT allow performer to actually perform this
notification. Ensure it is simulated.
CUE: Acknowledge report as Fire Protection Section Duty Shift
Supervisor.
COMMENTS:
I.-
STEP 12: [Step K] CONFIRM/COORDINATE MERT response (via radio or
phone) until Incident Commander assumes control.
STANDARD: Performer confirms/coordinate the MERT response until the
Incident Commander assumes control.
CUE: As Incident Commander, notify the performer that you
have assumed control of the emergency. We will stop
here.
COMMENTS:
END OF TASK I_________________________
TIME STOP:
Page 10 of 8
APPLICANT CUE SHEET
(TO BE RETURNED TO EXAMINER UPON COMPLETION OF TASK)
DIRECTION TO TRAINEE:
I will explain the initial conditions, and state the administrative task to be
performed. I will provide initiating cues and reports on other actions when
directed by you. Ensure you indicate to me when you understand your assigned
task. To indicate that you have completed your assigned task return the handout
sheet I provided you.
INITIAL CONDITIONS:
You are the Control Room Operator (CRO) on shift.
You have received a telephone call reporting an onsite medical emergency.
INITIATING CUES:
0 Respond to the medical emergency in accordance with EPIP-10.
Admin A.4/Scenario 2
Page 1 of 20
REGION II
INITIAL LICENSE EXAMINATION
Admin A.4/Scenario 2
Classify The Event Per The REP (Cold Leg LOCA)
APPLICANT
EXAMINER
Admin A.4/Scenario 2
Page 2 of 20
REGION II
INITIAL LICENSE EXAMINATION
Task: Classify The Event Per The REP (Cold Leg LOCA)
Alternate Path: N/A
Facility JPM #: New
K/A Rating(s): 2.4.38 [2.2/4.0]
Task Standard: The event is classified as an ALERT based on EAL 1.2.2, "RCS Leakage/LOCA"
Notifications are made per EPIP-3.
Preferred Evaluation Location: Preferred Evaluation Method:
Simulator X In-Plant Perform X Simulate
References: EPIP-1 "Emergency Plan Classification Flowpath", Rev. 15; EPIP-3 "ALERT", Rev. 16
Task Number: SRO-113-EPIP-001 APPLICABLE FOR: SRO
IOCFR55.45: 11
Validation Time: 20 min. Time Critical: No
Applicant: Time Start:
NAME SSN Time Finish:
Performance Rating: SAT UNSAT Performance Time
Examiner: /
NAME SIGNATURE DATE
COMMENTS
Admin A.4fScenario 2
Page 3 of 20
SIMULATOR OPERATOR INSTRUCTIONS:
1. This JPM will commence from the point where simulator is frozen at the end of
simulator exam scenario 2.
SIMULATOR OPERATOR INSTRUCTIONS:
1. Obtain copy of EPIP-3 to facilitate role plays for contacts made by the performer.
2. Performer must use NRC ring down phone.
Admin A.4lScenado 2
Page 4 of 20
ToolslEquipment/Procedures Needed:
Ensure clean copy of EPIP-3 in all copies of Emergency Instructions on the Simulator
Floor and in the file drawer of Unit Supervisor's desk..
READ TO OPERATOR
DIRECTION TO TRAINEE:
I will explain the initial conditions, and state the task to be performed. All control
room steps shall be performed for this JPM, including any required
communications. I will provide initiating cues and reports on other actions when
directed by you. Ensure you indicate to me when you understand your assigned
task. To indicate that you have completed your assigned task return the handout
sheet I provided you.
INITIAL CONDITIONS:
Simulator represents the current plant conditions.
Simulator operation is frozen.
INITIATING CUES:
Using the current conditions, make the initial classification of the event per the
REP and make the required notifications.
Z Iiuvi // I
Admin A.4/Scenario 2
Page 5 of 20
EXAMINER NOTE: This handout sheet and accompanying equation sheet is to be used
after JPM Step 18. Provide applicant with both sheets.
READ TO OPERATOR
NEW CONDITIONS:
"* A breech of containment has occurred resulting in a rapid reduction of
containment pressure to approximately atmospheric pressure.
"* Incore thermocouples indicate 850'F Hi quadrant average
"* RVLIS Level is 60%
"* A radiological field team reported that measured external dose at 7 miles
from the plant is 200 mr/hr.
A General Emergency has been declared.
INITIATING CUES:
Make the Protective Action Recommendations for this declaration. When
determining 2 and 5 mile dose rates, assume that these readings are measured
from a point source at the plant. (Ignore all atmospheric conditions that would
affect measurements)
Admin A.4/Scenario 2
Page 6 of 20
START TIME:
STEP 1: Refers to EPIP-1 to determine level of event. CRITICAL
STEP
STANDARD: Performer refers to EPIP-1 and declares an ALERT based
on EAL 1.2.2, "RCS Leakage/LOCA". This must be
completed within 15 minutes of task assignment. SAT
This step is critical to ensure proper activation of TVA
resources for event in progress.
UNSAT
3OMMENTS: RECORD time that declaration was made:
STEP 2: Implements EPIP-3, ALERT
STANDARD: EPIP-3, ALERT, is implemented.
COMMENTS: UNSAT
"**Italicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Admin A.4lScenario 2
Panae 7 of 2n1
Prw 7 nf 2fl
STEP 3: [STEP 1] DIRECT Shift Personnel to activate the CRITICAL
Emergency Paging System (EPS) to staff the TSC and STEP
Operations Support Center (OSC). Shift Personnel should
confirm activation and provide the 20 minute printed report __SAT
to the SM for review.
STANDARD: Shift personnel is notified to activate the emergency paging UNSAT
system (EPS) to staff the TSC and Operations Support
Center (OSC) or EPS is activated in the control room.
This step is critical to ensure proper activation of TVA
resources for event in progress.
- CUE: After the shift personnel is notified, acknowledge the
request to activate the Emergency Paging System.
COMMENTS:
NOTE I IF the EPS system fails, call the ODS (5-751-1700) and have
him activate the EPS.
NOTE 2 IF the above methods of activating the EPS fail, the Shift
Personnel must use the Radiological Emergency Response
Call Lists to staff the TSC and OSC. This list is located in
the EPS Manual near the terminal.
STEP 4: [STEP 2] COMPLETE Appendix A, Notification
Information.
STANDARD: Appendix A is accurately completed.
COMMENTS: UNSAT
"*ItalicizedCues Are To Be Used Only if JPM PerformanceIs Being Simulated.
Admin A.4/Scenario 2
Page 8 of 20
STEP 5: [STEP 3] ANNOUNCE to the crew: "An Alert is being CRITICAL
STEP
declared based on EAL 1.2.2, "RCS Leakage/LOCA." I will
be the Site Emergency Director."
STANDARD: The above announcement is made to the crew. Wording
describing the event may vary. This must be completed
within 15 minutes of task assignment. UNSAT
Step is critical to alert crew to the declaration of the
ALERT.
- CUE: After the crew is notified, acknowledge the report.
COMMENTS: RECORD time that declaration was made:
t
STEP 6: [STEP 4] NOTIFY the ODS direct by ODS Ringdown or CRITICAL
STEP
No. 5-751-1700 or 5-751-2495 and PROVIDE the
information from Appendix A. If the ODS cannot be SAT
contacted within 10 minutes, the Tennessee Emergency
Management Agency is to be notified of the Radiological
Emergency Plan activation by calling 9-1-800-262-3300 or
9-1-615-741-0001 or 9-1-800-262-3400. UNSAT
STANDARD: The ODS is notified and provided the information on
Appendix A. This notification must be made within 5
minutes of event declaration.
Step is critical to ensure timely staffing of CECC.
EVALUATOR NOTE: DO NOT allow actual call to ODS. Ensure call is
to simulator instructor.
- CUE: (Booth Operator) Role play the ODS and repeat back
the report.
COMMENTS: RECORD time that ODS was notified:
"**ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Admin A.4/Scenario 2
Page 9 of 20
STEP 7: [STEP 5] FAX Appendix A to the ODS.(No. pre
programmed or 5-751-8620.)
STANDARD: Appendix A is placed in the fax machine and transmission
simulated.
UNSAT
- CUE: Do NOT allow fax to be transmitted.
COMMENTS:
i
STEP 8: [STEP 6] ANNOUNCE to the plant: "ATTENTION ALL CRITICAL
STEP
SITE PERSONNEL. ATTENTION ALL SITE PERSONNEL.
AN ALERT emergency has been declared based on EAL
1.2.2, "RCS Leakage/LOCA."
(Repeat)
STANDARD: A public address announcement for Plant Emergency
UNSAT
Response Personnel to staff the TSC and OSC is made
over the plant paging system. Wording describing the event
may vary.
Step is critical to alert all plant personnel of the REP
declaration and instructions staffing TSC and OSC.
COMMENTS:
- Italicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Admin A.4/Scenario 2
Page 10 of 20
STEP 9: [STEP 7] EVALUATE plant conditions, and IF conditions
warrant, INITIATE assembly and accountability by
completing steps 8 and 9. (For additional details, go to
WBN EPIP-8, "Personnel Accountability and Evacuation"). SAT
IF you are not going to initiate assembly and accountability,
GO TO step 10.
STANDARD: Performer decides whether conditions warrant initiating UNSAT
assembly and accountability or whether the conditions do
NOT warrant assembly and accountability. If the decision
is that conditions do then the performer proceeds to
step 8 (JPM STEP 10). If the decision is that conditions
do NOT then the performer goes to the step 10 (JPM
STEP 14). Either is acceptable.
NOTE: Limited Area Evacuation per EPIP-8 App B may be
implemented and if so skip to procedure step 10 (JPM step
14).
COMMENTS:
EVALUATOR NOTE Steps 10, 11, and 12 are all part of the same
procedure step.
STEP 10: [STEP 8] NOTIFY Security (CAS) that assembly and CRITICAL
accountability is to be conducted. STEP
STANDARD: The performer notifies Security that assembly and
accountability is to be conducted. SAT
This step is critical to enable assembly card readers.
- CUE: (Booth Operator) If RADCON is notified to implement UNSAT
EPIP-16, acknowledge the report.
COMMENTS:
"**ItalicizedCues Are To Be Used Only if JPM PerformanceIs Being Simulated.
Admin A.4/Scenario 2
Page 11 of 20
CAUTION If there is any possibility of a radiological release, do
not send personnel into areas of unknown radiological
conditions without first contacting Radiological Control
(RADCON).
EVALUATOR NOTE: Performance Steps 11, 12, and 13 will only be
critical if the decision was made to initiate
assembly & accountability.
EVALUATOR NOTE: Performance Steps 11, 12, and 13 are all part of
the same Procedure step.
STEP 11: [STEP 9] ANNOUNCE to the plant: "ATTENTION ALL CRITICAL
SITE PERSONNEL. ATTENTION ALL SITE PERSONNEL. STEP
Report to your assembly areas for accountability."
(Repeat) AND SAT
STANDARD: The above announcement is made for all site personnel to
report to their assembly areas for accountability.
UNSAT
Step is critical to alert all plant personnel of the
assembly & accountability instructions.
COMMENTS:
STEP 12: [STEP 9] ACTIVATE assembly alarm for personnel CRITICAL
assembly and accountability. STEP
STANDARD: The performer pushes assembly alarm "EVAC AUTO" or
"EVAC MANUAL" push button. __ SAT
This step is critical to activate assembly &
accountability alarm.
UNSAT
COMMENTS:
- ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Admin A.4lScenario 2
Page 12 of 20
I
STEP 13: [STEP 9] INITIATE WBN EPIP-8, "Personnel CRITICAL
Accountability and Evacuation". STEP
STANDARD: The performer refers to EPIP-8, Appendix C, to determine
actions necessary for personnel accountability and SAT
evacuation.
This step is critical in that specific guidance is given
with regard to assembly & accountability.. UNSAT
- CUE: After the performer has determined which sections of
EPIP-8 apply, direct him/her to return to EPIP-3 and
continue actions.
COMMENTS:
i
STEP 14: [STEP 10] CALL RADCON Lab and SAY: "We are in an CRITICAL
Alert, implement WBN EPIP-14, and CECC EPIP-9." STEP
STANDARD: The RADCON Lab is notified to implement WBN EPIP-14
This step is critical to notify RADCON so proper
survey's, etc are implemented.
UNSAT
- CUE: (Booth Operator) Acknowledge the request to
implement WBN EPIP-14 and CECC EPIP-9.
COMMENTS:
"**ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Admin A.4/Scenario 2
Page 13 of 20
STEP 15: [STEP 11] IF there are personnel injuries, IMPLEMENT
WBN EPIP-10, "Medical Emergency Response."
STANDARD: Performer determines that it is NOT necessary to
implement EPIP-10.
- CUE: Inform the performer that there are NO personnel UNSAT
injuries.
COMMENTS:
I
STEP 16: [STEP 12] IF there is a security threat, IMPLEMENT WBN
EPIP-1 1, "Security and Access Control."
STANDARD: Performer determines that it is NOT necessary to
implement EPIP-1 1.
- CUE: Inform the performer that there has been NO reports UNSAT
of a security threat
COMMENTS:
I____________________________
STEP 17: [STEP 13] NOTIFY Duty Plant Manager, and PROVIDE CRITICAL
Appendix A information (SEE duty list for telephone STEP
numbers). The Duty Plant Manager will call the Plant
Manager or his alternate.
STANDARD: Duty Plant Manager is provided the Appendix A information.
This step is critical as it alerts plant management to
REP activation. UNSAT
- CUE: (Booth Operator) Role play as the Duty Plant Manager
and acknowledge the report.
COMMENTS:
-j.
"**Italicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Admin A.4/Scenario 2
Page 14 of 20
I -
STEP 18: [STEP 14] EVALUATE the need to implement EPIP-16,
"Initial Dose Assessment for Radiological Emergencies," for
a dose projection if radioactivity is being released through
normal plant release paths. SAT
STANDARD: The performer determines whether or not EPIP-16 is to be
implemented. Either decision is acceptable.
UNSAT
- CUE: (Booth Operator) If RADCON is notified to implement
EPIP-16, acknowledge the report.
COMMENTS:
NOTE NRC notification should be made as soon as I
practicable but within one hour of "Alert" declaration.
Whenever NRC requests, a qualified person must
provide a continuous update to NRC Operations
Center. The following commercial numbers are for the
NRC Operations Center.
9-1-301-816-5100 (MAIN)
9-1-301-951-0550 (BACKUP)
9-1-301-816-5151 (FAX)
EVALUATOR NOTE: DO NOT allow actual call to NRC.
Ensure call is to simulator instructor.
i
STEP 19: [STEP 15] NOTIFY the NRC, using designated NRC CRITICAL
phone (ENS), of plan activation. STEP
STANDARD: The NRC is notified of plan activation using designated
line. SAT
This step is critical as it alerts NRC to REP activation.
EVALUATOR NOTE: DO NOT allow actual call to NRC. Ensure call is UNSAT
to simulator instructor.
- CUE: (Booth Operator) Role play the NRC and acknowledge
the report.
COMMENTS:
- ltalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Admin A.4/Scenario 2
Page 15 of 20
STEP 20: [STEP 16] NOTIFY the NRC Resident Inspector by calling CRITICAL
1776 and PROVIDING the information on Appendix A. STEP
STANDARD: The NRC Resident Inspector is provided Appendix A SAT
information.
This step is critical as it alerts NRC to REP activation.
UNSAT
EVALUATOR NOTE: DO NOT allow actual call to NRC Resident.
Ensure call is to simulator instructor.
- CUE: (Booth Operator) Role play the NRC Resident and
acknowledge the report.
COMMENTS:
EVALUATOR CUE: State to applicant that conditions have now
changed. A General Emergency has been
declared.
EVALUATOR CUE: Read and provide Applicant handout sheet
and equation sheet for PAR
recommendations.
STEP 21: Refers to EPIP-5 to Appendix B "Protective Action SAT
Recommendation Guidance.
STANDARD: Applicant obtains copy of EPIP-5 Appendix B. UNSAT
COMMENTS:
"**ltalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Admin A.4/Scenario 2
Page 16 of 20
STEP 22: General Emergency Declared. SAT
STANDARD: Applicant enters logic tree at top of page since general
emergency has been declared. (given in applicant's UNSAT
handout sheet.)
COMMENTS:
-I-
STEP 23: Is Projected or Measured Dose Greater Than or Equal to SAT
Table 1 Limits at or beyond 5 miles.
STANDARD: Applicant determines that measured external dose does UNSAT
NOT exceed table 1 limits, therefore applicant answers NO
to logic question and continues to the next decision block
on the PAR flowchart.
Applicant calculates dose at 5 miles using point source
equation:
11 (d)2 = 12 (d 2) 2
2
200mr./hr(7mi) = 12 (5mi)2
12 = 9800/25 = 392 mr/hr = 0.392 R/hr
(external dose rate at 5 miles)
COMMENTS:
"**Italicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Admin A.4/Scenario 2
Page 17 of 20
STEP 24: Indications of Severe Core Damage Greater Than or Equal
to the Values in Table 2.
STANDARD: Applicant determines that a table 2 limit has been NOT
been exceeded, therefore applicant answers NO to logic
question and continues to the next decision block on the
PAR flowchart. UNSAT
COMMENTS:
I____________________________
STEP 25: Is there loss of Physical Control of the Facility.
STANDARD: Applicant determines that physical control of the facility has SAT
NOT been lost (security status from earlier has not
changed), therefore applicant answers NO to logic question
and continues to the next decision block on the PAR
flowchart. UNSAT
- CUE: Inform the performer that there has been NO reports
of a security threat
COMMENTS:
I____________________________
"**ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Admin A.4/Scenario 2
Page 18 of 20
STEP 26: Is Projected or Measured Dose Greater Than or Equal to
Table 1 Limits at or beyond 2 miles. CRITICAL
STEP
STANDARD: Applicant determines that dose exceeds table 1 limits (1
REM/hr external dose) at 2 miles or beyond, therefore
applicant answers YES to logic question. Applicant then
determines that the logic indicates Recommendation 2 as
the Protective Action Recommendation.
Applicant calculates dose at,5'miles using point source
equation:
11(d1)2= 12 (d2 )2
200mr./hr(7mi)f = 12 (2mi)f
12 = 9800/4 = 2450 mr/hr = 2.45 R/hr
(external dose rate at 2 miles)
This step is critical for making the appropriate PAR to
the CECC.
- CUE: Acknowledge report by the applicant
COMMENTS:
END OF TASK I
TIME STOP:
"**Italicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Page 19 of 20
APPLICANT CUE SHEET
(TO BE RETURNED TO EXAMINER UPON COMPLETION OF TASK)
DIRECTION TO TRAINEE:
I will explain the initial conditions, and state the task to be performed. All control
room steps shall be performed for this JPM, including any required
communications. I will provide initiating cues and reports on other actions when
directed by you. Ensure you indicate to me when you understand your assigned
task. To indicate that you have completed your assigned task return the handout
sheet I provided you.
INITIAL CONDITIONS:
Simulator represents the current plant conditions.
Simulator operation is frozen.
INITIATING CUES:
Using the current conditions, make the initial classification of the event per the
REP and make the required notifications.
Page 20 of 20
APPLICANT HANDOUT SHEET
(TO BE RETURNED TO EXAMINER UPON COMPLETION OF TASK)
NEW CONDITIONS:
"* A breech of containment has occurred resulting in a rapid reduction of
containment pressure to approximately atmospheric pressure.
"* Incore thermocouples indicate 850°F Hi quadrant average
"* RVLIS Level is 60%
"* A radiological field team reported that measured external dose at 7 miles
from the plant is 200 mr/hr.
A General Emergency has been declared.
INITIATING CUES:
Make the Protective Action Recommendations for this declaration. When
determining 2 and 5 mile dose rates, assume that these readings are measured
from a point source at the plant. (Ignore all atmospheric conditions that would
affect measurements)
V VLCc p
EQUATIONS
- = IiicpAT
Q =rhicpAh p = PoeU/
S
0=UAAT SCR= (1 - Keff)
6 P) CR 2
S 2 6 .0 (Xeff CR1 = (1- Keffl) = CR1
(B-p)
SUR M= (1- Kefn)
tu (1-
Keff2)
p p=(Kff
SDM =
AK.ff
11(dl)= 12(d2)
P= -Keff
e* + (f-P) 11(dl) 2 12(d2) 2
1 X 10-4 seconds Wpump ffiAPv
Net Work (in)
(out)
keff =.01 seconds-1 Cycle Efficiency = Energy
CONVERSIONS
1 Curie = 3.7 x 1010 dps 1 kg = 2.21 Ibm
1 hp = 2.54 x 103 Btu/hr 1 MW = 3.41 x 106 Btu/hr
OF = 9/5 OC + 32
1 Btu = 778 ft-lbf
OC = 5/9 (OF - 32)
Admin A.4/Scenario 3
Page 1 of 16
REGION II
INITIAL LICENSE EXAMINATION
Admin A.4lScenario 3
Classify The Event Per The REP (Steam Line Break Inside
Containment)
APPLICANT
EXAMINER
Admin A.4fScenario 3
Page 2 of 16
REGION Ii
INITIAL LICENSE EXAMINATION
Task: Classify The Event Per The REP (Steam Line Break Inside Containment)
Alternate Path: N/A
Facility JPM #: New
K/A Rating(s): 2.4.38 [2.2/4.0]
Task Standard: The event is classified as an Unusual Event based on EAL 2.7 "Uncontrolled Cooldown."
Notifications are made per EPIP-2.
Preferred Evaluation Location: Preferred Evaluation Method:
Simulator X In-Plant Perform X Simulate
References: EPIP-1 "Emergency Plan Classification Flowpath", Rev. 15; EPIP-2 "Notification Of
Unusual Event", Rev. 13
Task Number: SRO-113-EPIP-001 APPLICABLE FOR: SRO
10CFR55.45: 11
Validation Time: 20 min. Time Critical: YES
Applicant: Time Start:
NAME SSN Time Finish:
Performance Rating: SAT. UNSAT Performance Time
Examiner: I
NAME SIGNATURE DATE
COMMENTS
Admin A.4/Scenario 3
Page 3 of 16
SIMULATOR OPERATOR INSTRUCTIONS:
1. This JPM will commence from the point where simulator is frozen at the end of
simulator exam scenario 3.
SIMULATOR OPERATOR INSTRUCTIONS:
1. Obtain copy of EPIP-2 to facilitate role plays for contacts made by the performer.
2. Performer must use NRC ring down phone.
Admin A.4/Scenario 3
Page 4 of 16
Needed:
ToolslEquipment/Procedures
Ensure clean copy of EPIP-2 in all copies of Emergency Instructions on the Simulator
Floor and in the file drawer of Unit Supervisor's desk.
READ TO OPERATOR
DIRECTION TO TRAINEE:
I will explain the initial conditions, and state the task to be performed. All control
room steps shall be performed for this JPM, including any required
communications. I will provide initiating cues and reports on other actions when
directed by you. Ensure you indicate to me when you understand your assigned
task. To indicate that you have completed your assigned task return the handout
sheet I provided you.
INITIAL CONDITIONS:
Simulator represents the current plant conditions.
Simulator operation is frozen.
INITIATING CUES:
Using the current conditions, make the initial classification of the event per the
REP and make the required notifications.
THIS IS A TIME CRITICAL TASK
Admin A.4/Scenario 3
Page 5 of 16
EXAMINER NOTE: This handout sheet and accompanying equation sheet is to be used
after JPM Step 18. Provide applicant with both sheets.
READ TO OPERATOR
NEW CONDITIONS:
A LOCA occurs from present conditions resulting in the following:
"* CNTMT pressure 7.0 psig with NO CNTMT Spray Pumps running.
"* RVLIS Level 17% and stable.
"* Core Cooling RED path.
"* A radiological field team reported that measured external dose at 7 miles
from the plant is 10 mr/hr.
A General Emergency has been declared.
INITIATING CUES:
Make the Protective Action Recommendations for this declaration. When
determining 2 and 5 mile dose rates, assume that these readings are measured
from a point source at the plant. (Ignore all atmospheric conditions that would
affect measurements)
Admin A.4/Scenario 3
Page 6 of 16
START TIME:
STEP 1: Refers to EPIP-1 to determine level of event. CRITICAL
STEP
STANDARD: Performer refers to EPIP-1 and declares an Notification Of
Unusual Event based on EAL 2.7 "Uncontrolled Cooldown."
This must be completed within 15 minutes of task SAT
assignment.
This step is critical to ensure proper activation of TVA
resources for event in progress. UNSAT
3OMMENTS: RECORD time that declaration was made:
I
STEP 2: Implements EPIP-2, Notification Of Unusual Event
STANDARD: EPIP-2, Notification Of Unusual Event, is implemented.
COMMENTS: UNSAT
STEP 15: [STEP 1] IF there are personnel injuries, IMPLEMENT
WBN EPIP-10, "Medical Emergency Response."
STANDARD: Performer determines that it is NOT necessary to
implement EPIP-10.
- CUE: Inform the performer that there are NO personnel UNSAT
injuries.
COMMENTS:
"**ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Admin A.4/Scenario 3
Page 7 of 16
STEP 4: [STEP 2] COMPLETE Appendix A, Notification
Information.
STANDARD: Appendix A is accurately completed.
COMMENTS: UNSAT
a-
STEP 5: [STEP 3] ANNOUNCE to the crew: "An Notification of CRITICAL
Unusual Event is being declared based on EAL 2.7 STEP
"Uncontrolled Cooldown." I will be the Site Emergency
Director." SAT
STANDARD: The above announcement is made to the crew. Wording
describing the event may vary. This must be completed
within 15 minutes of task assignment. UNSAT
Step is critical to alert crew to the declaration of the
Notification of Unusual Event.
- CUE: After the crew is notified, acknowledge the report.
COMMENTS: RECORD time that declaration was made:
I_____________
"**ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Admin A.4/Scenario 3
Page 8 of 16
STEP 6: [STEP 4] NOTIFY the ODS direct by ODS Ringdown or CRITICAL
No. 5-751-1700 or 5-751-2495 and PROVIDE the STEP
information from Appendix A. If the ODS cannot be
contacted within 10 minutes, the Tennessee Emergency SAT
Management Agency is to be notified of the Radiological
Emergency Plan activation by calling 9-1-800-262-3300 or
9-1-615-741-0001 or 9-1-800-262-3400.
UNSAT
STANDARD: The ODS is notified and provided the information on
Appendix A. This notification must be made within 5
minutes of event declaration.
Step is critical to ensure timely staffing of CECC.
EVALUATOR NOTE: DO NOT allow actual call to ODS. Ensure call is
to simulator instructor
- CUE: (Booth Operator) Role play the ODS and repeat back
the report.
COMMENTS: RECORD time that ODS was notified:
STEP 7: [STEP 5] FAX Appendix A to the ODS.(No. pre
programmed or 5-751-8620.)
STANDARD: Appendix A is placed in the fax machine and transmission
simulated.
- CUE: Do NOT allow fax to be transmitted. UNSAT
COMMENTS:
"**Italicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Admin A.4/Scenario 3
Page 9 of 16
STEP 8: [STEP 6] ANNOUNCE to the plant: "ATTENTION ALL CRITICAL
SITE PERSONNEL. ATTENTION ALL SITE PERSONNEL. STEP
A Notification of Unusual Event is being declared based on
EAL 2.7 "Uncontrolled Cooldown." (Repeat) SAT
STANDARD: A public address announcement for Notification of Unusual
Event. Wording describing the event may vary.
UNSAT
Step is critical to alert all plant personnel of the REP
declaration.
COMMENTS:
STEP 9: [STEP 7] NOTIFY Duty Plant Manager, and PROVIDE CRITICAL
Appendix A information (SEE duty list for telephone STEP
numbers). The Duty Plant Manager will call the Plant
Manager or his alternate.
STANDARD: Duty Plant Manager is provided the Appendix A information.
This step is critical as it alerts plant management to
REP activation. UNSAT
- CUE: (Booth Operator) Role play as the Duty Plant Manager
and acknowledge the report.
COMMENTS:
"**ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Admin A.4/Scenario 3
Page 10 of 16
NOTE If the EPS system fails, call the ODS ringdown or (5
751-1700) and have him activate the EPS.
STEP 10: [STEP 8] IF TSC and OSC support is needed, ACTIVATE CRITICAL
the emergency system paging (EPS). STEP
STANDARD: Performer contacts shift personnel to activate EPS or EPS
is activated in the control room, or performer decides NOT SAT
to staff the TSC/OSC at this time.
This step is critical to ensure proper activation of TVA
resources for event in progress. UNSAT
- CUE: After the shift personnel is notified, acknowledge the
request to activate the Emergency Paging System.
COMMENTS:
"**ltalicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Admin A.4/Scenario 3
Page I1I of 16
of 16 3
NOTE NOTENRC notification should be made as soon as practicable but Page 11A.41Scenario
Admin
within one hour of "NOTIFICATION OF UNUSUAL EVENT"
declaration. Whenever NRC requests, a qualified person
must provide a continuous update to NRC Operations Center.
The following commercial numbers are for the NRC
Operations Center
9-1-301-816-5100 (MAIN)
9-1-301-951-0550 (BACKUP)
9-1-301-816-5151 (FAX)
EVALUATOR NOTE: DO NOT allow actual call to NRC.
Ensure call is to simulator instructor.
STEP 11: [STEP 9] NOTIFY the NRC, using designated NRC phone CRITICAL
(ENS), of plan activation. STEP
STANDARD: The NRC is notified of plan activation using designated
line. SAT
This step is critical as it alerts NRC to REP activation.
EVALUATOR NOTE: DO NOT allow actual call to NRC. Ensure call is UNSAT
to simulator instructor.
- CUE: (Booth Operator) Role play the NRC and acknowledge
the report.
COMMENTS:
I
STEP 12: [STEP 10] EVALUATE the need to implement EPIP-16,
"Initial Dose Assessment for Radiological Emergencies," for
a dose projection if radioactivity is being released through
normal plant release paths. SAT
STANDARD: The performer determines whether or not EPIP-16 is to be
implemented. Either decision is acceptable.
UNSAT
- CUE: (Booth Operator) If RADCON is notified to implement
EPIP-16, acknowledge the report.
COMMENTS:
"*ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Admin A.4/Scenario 3
Page 12 of 16
STEP 13: [STEP 11] NOTIFY WBN Emergency Preparedness. SAT
NOTE Notification to Emergency Preparedness should be made
as soon as practicable, but only when notification does not
interfere with emergency actions or notifications in UNSAT
progress.
Work - 3232 or Work - 8004
Home - 9-1-423-337-2911 Home -9-1-423-842-3020
Pager - 30374 Pager - 30388
STANDARD: WBN Emergency Preparedness is notified of plan
activation.
EVALUATOR NOTE: DO NOT allow actual call to WBN Emergency
Preparedness. Ensure call is to simulator
instructor.
- CUE: (Booth Operator) Role play as WBN Emergency
Preparedness and acknowledge the report.
COMMENTS:
EVALUATOR CUE: State to applicant that conditions have now
changed. A General Emergency has been
declared.
EVALUATOR CUE: Read and provide Applicant handout sheet
and equation sheet for PAR
recommendations.
STEP 14: Refers to EPIP-5 to Appendix B "Protective Action SAT
Recommendation Guidance.
STANDARD: Applicant obtains copy of EPIP-5 Appendix B. UNSAT
COMMENTS:
- ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Admin A.4/Scenario 3
Page 13 of 16
STEP 15: General Emergency Declared. SAT
STANDARD: Applicant enters logic tree at top of page since general
emergency has been declared. (given in applicant's UNSAT
handout sheet.
COMMENTS:
STEP 16: Is Projected or Measured Dose Greater Than or Equal to SAT
Table 1 Limits at or beyond 5 miles.
STANDARD: Applicant determines that measured external dose does UNSAT
NOT exceed table 1 limits, therefore applicant answers NO
to logic question and continues to the next decision block
on the PAR flowchart.
Applicant calculates dose at 5 miles using point source.
equation:
11(d1)2 = 12 (d2 )2
10mr./hr(7mi)2 = 12 (5mi)2
12 = 490/25 = 19.6 mr/hr = 0.0196 R/hr
(external dose rate at 5 miles)
COMMENTS:
- Italicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Admin A.4/Scenario 3
Page 14 of 16
STEP 17: Indications of Severe Core Damage Greater Than or Equal
to the Values in Table 2. CRITICAL
STEP
STANDARD: Applicant determines that a table 2 limit has been exceeded
(Inadequate Core Cooling as indicated by "red" path from
core cooling status trees), answer is YES to the logic SAT
question. Applicant then determines that the logic indicates
Recommendation 2 as the Protective Action
Recommendation.
UNSAT
This step is critical for making the appropriate PAR to
the CECC.
- CUE: Acknowledge report by the applicant
COMMENTS:
END OF TASK I____________________________
TIME STOP:
"**Italicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Page 15 of 16
APPLICANT CUE SHEET
(TO BE RETURNED TO EXAMINER UPON COMPLETION OF TASK)
DIRECTION TO TRAINEE:
I will explain the initial conditions, and state the task to be performed. All control
room steps shall be performed for this JPM, including any required
communications. I will provide initiating cues and reports on other actions when
directed by you. Ensure you indicate to me when you understand your assigned
task. To indicate that you have completed your assigned task return the handout
sheet I provided you.
INITIAL CONDITIONS:
Simulator represents the current plant conditions.
Simulator operation is frozen.
INITIATING CUES:
Using the current conditions, make the initial classification of the event per the
REP and make the required notifications.
THIS IS A TIME CRITICAL TASK
Page 16 of 16
APPLICANT HANDOUT SHEET
(TO BE RETURNED TO EXAMINER UPON COMPLETION
OF TASK)
NEW CONDITIONS:
A LOCA occurs from present conditions resulting in the
following:
"* CNTMT pressure 7.0 psig with NO CNTMT Spray Pumps
running.
"* RVLIS Level 17% and stable.
"* Core Cooling RED path.
"* A radiological field team reported that measured external
dose at 7 miles
from the plant is 10 mr/hr.
A General Emergency has been declared.
INITIATING CUES:
Make the Protective Action Recommendations for this declaration.
When
determining 2 and 5 mile dose rates, assume that these
readings are measured
from a point source at the plant. (Ignore all atmospheric
conditions that would
affect measurements)
EQUATIONS
(*= iCpAT P =PO 10 SUR(t)
0Q= licpAh p = poe0
S
- =UAAT SCR= ((I - KMf
p) CRI = (I1-Kerni) = CR2
SUR =26.06(Xeff CR1
(U-p)
26.06 M= (1- KM)
SU= R
(1- Keff)
AKff
P - Keff 11(dl)= 12(d 2)
2
( P)] Ii(dl)
2 =I 2 (d 2 )
p" - XeffP
1 x 10-4 seconds *pump= riAPv
Net Work (out)
ý,eff =.01 seconds-1 Cycle Efficiency =
Energy (in)
CONVERSIONS
1 Curie = 3.7 x 1010 dps 1 kg = 2.21 Ibm
1 hp = 2.54 x 103 Btu/hr 1 MW = 3.41 xl06Btu/hr
OF = 9/5 °C + 32
1 Btu = 778 ft-lbf
°C = 5/9 (OF - 32)
Admin A.4/Scenario 1
Page 1 of 18
REGION II
INITIAL LICENSE EXAMINATION
Admin A.4 /Scenario 1
Classify The Event Per The REP (SGTR With Ruptured SG
Faulted Outside Containment)
APPLICANT
EXAMINER
Admin A.4lScenario 1
Page 2 of 18
REGION II
INITIAL LICENSE EXAMINATION
Task: Classify The Event Per The REP (SGTR With Ruptured SG Faulted Outside Containment)
Alternate Path: N/A
Facility JPM #: New
K/A Rating(s): 2.4.38 [2.2/4.0] 2.4.30 [2.2/3.6]
Task Standard: The event is classified as an SITE AREA EMERGENCY based on EAL 1.2.3 "Steam Generator
Tube Rupture" and EAL 1.3.4 "Containment Bypass." Notifications are made per EPIP-4.
Preferred Evaluation Location: Preferred Evaluation Method:
Simulator X In-Plant Perform X Simulate
References: EPIP-1 "Emergency Plan Classification Flowpath", Rev. 15; EPIP-4 "SITE AREA
EMERGENCY", Rev. 17
Task Number: SRO-113-EPIP-001 APPLICABLE FOR: SRO
10CFR55.45: 11
Validation Time: 22 min. Time Critical: Yes
Applicant: Time Start:
NAME SSN Time Finish:
Performance Rating: SAT_ UNSAT Performance Time
Examiner: /
NAME SIGNATURE DATE
COMMENTS
Admin A.4/Scenario 1
Page 3 of 18
SIMULATOR OPERATOR INSTRUCTIONS:
1. This JPM will commence from the point where simulator is frozen at the end of
simulator exam scenario 1
SIMULATOR OPERATOR INSTRUCTIONS:
1. Obtain copy of EPIP-4 to facilitate role plays for contacts made by the performer.
2. Performer must use NRC ring down phone.
Admin A.4/Scenario 1
Page 4 of 18
ToolslEquipmentlProcedures Needed:
Ensure clean copy of EPIP-4 in all copies of Emergency Instructions on the Simulator
Floor and in the file drawer of Unit Supervisor's desk..
READ TO OPERATOR
DIRECTION TO TRAINEE:
I will explain the initial conditions, and state the task to be performed. All control
room steps shall be performed for this JPM, including any required
communications. I will provide initiating cues and reports on other actions when
directed by you. Ensure you indicate to me when you understand your assigned
task. To indicate that you have completed your assigned task return the handout
sheet I provided you.
INITIAL CONDITIONS:
Simulator represents the current plant conditions.
Simulator operation is frozen.
INITIATING CUES:
Using the current conditions, make the initial classification of the event per the
REP and make the required notifications.
THIS IS A TIME CRITICAL TASK
Admin A.4/Scenario 1
Page 5 of 18
EXAMINER NOTE: This handout sheet and accompanying equation sheet is to be used
after JPM Step 18. Provide applicant with both sheets.
READ TO OPERATOR
NEW CONDITIONS:
"* Chemistry reported RCS activity is now 350 pcilgm dose equivalent Iodine
131
"* A radiological field team reported that measured external dose at 7 miles
from the plant is 800 mr/hr.
A General Emergency has been declared.
INITIATING CUES:
Make the Protective Action Recommendations for this declaration. When
determining 2 and 5 mile dose rates, assume that these readings are measured
from a point source at the plant. (Ignore all atmospheric conditions that would
affect measurements)
"**ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Admin A.4/Scenario 1
Page 6 of 18
START TIME:
I
STEP 1: Refers to EPIP-1 to determine level of event. CRITICAL
STEP
STANDARD: Performer refers to EPIP-1 and declares an SITE AREA
EMERGENCY based on EAL 1.2.3 "Steam Generator Tube SAT
Rupture" and EAL 1.3.4 "Containment Bypass." This must
be completed within 15 minutes of task assignment.
This step is critical to ensure proper activation of TVA
UNSAT
resources for event in progress.
COMMENTS: RECORD time that declaration was made:
STEP 2: Implements EPIP-4, SITE AREA EMERGENCY
STANDARD: EPIP-4, SITE AREA EMERGENCY, is implemented.
UNSAT
COMMENTS:
I
"**ItalicizedCues Are To Be Used Only if JPM PerformanceIs Being Simulated.
Admin A.4/Scenario 1
Page 7 of 18
CRITICAL
STEP 3: [STEP 1] DIRECT Shift Personnel to activate the CRITICAL
Emergency Paging System (EPS) to staff the TSC and STEP
Operations Support Center (OSC). Shift Personnel should
confirm activation and provide the 20 minute printed report SAT
to the SM for review.
STANDARD: Shift personnel is notified to activate the emergency paging
system (EPS) to staff the TSC and Operations Support UNSAT
Center (OSC) or EPS is activated in the control room.
This step is critical to ensure proper activation of TVA
resources for event in progress.
- CUE: After the shift personnel is notified, acknowledge the
request to activate the Emergency Paging System.
COMMENTS:
NOTE 1 IF the EPS system fails, call the ODS (5-751-1700) and have
him activate the EPS.
NOTE 2 IF the above methods of activating the EPS fail, the Shift
Personnel must use the Radiological Emergency Response
Call Lists to staff the TSC and OSC. This list is located in
the EPS Manual near the terminal.
STEP 4: [STEP 2] COMPLETE Appendix A, Notification
Information.
STANDARD: Appendix A is accurately completed.
COMMENTS: UNSAT
- Italicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Admin A.4/Scenario 1
Page 8 of 18
STEP 5: [STEP 3] ANNOUNCE to the crew: "A SITE AREA CRITICAL
EMERGENCY is being declared based on EAL 1.2.3 STEP
"Steam Generator Tube Rupture" and EAL 1.3.4
"Containment Bypass.". I will be the Site Emergency SAT
Director, all support and job assignments must be
authorized through me."
STANDARD: The above announcement is made to the crew. Wording UNSAT
describing the event may vary. This must be completed
within 15 minutes of task assignment.
Step is critical to alert crew to the declaration of the
SITE AREA EMERGENCY and provide for tracking
personnel.
- CUE: After the crew is notified, acknowledge the report.
COMMENTS: RECORD time that declaration was made:
"**ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Admin A.4/Scenario 1
Page 9 of 18
[STEP 4] NOTIFY the ODS direct by ODS Ringdown or CRITICAL
STEP 6: STEP
No. 5-751-1700 or 5-751-2495 and PROVIDE the
information from Appendix A. SAT
IF the ODS cannot be contacted within 10 minutes, then
directly notify Rhea County, Meigs County, McMinn
County, and the Tennessee Emergency Management UNSAT
Agency (TEMA) of the classification.
Rhea County EMA 9-775-2505 -. (TIME)
9-775-7828 __(TIME)
(Alternate)
9-1-423-334-3049 -(TIME)
Meigs County EMA
9-1-423-334-5268 -(TIME)
(Alternate)
9-1-423-744-2760 -(TIME)
McMinn County
9-1-423-744-2721 -(TIME)
(Alternate)
9-1-800-262-3300 __(TIME)
9-1-615-741-0001 _ _(TIME)
(Alternate)
9-1-800-262-3400 -(TIME)
(Alternate)
STANDARD: The ODS is notified and provided the information on
Appendix A. This notification must be made within 5
minutes of event declaration.
Step is critical to ensure timely staffing of CECC and
notification of the appropriate state agencies.
EVALUATOR NOTE: DO NOT allow actual call to ODS. Ensure call is
to simulator instructor
- CUE: (Booth Operator) Role play as the ODS and repeat
back the report.
COMMENTS: RECORD time that ODS was notified:
"**ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Admin A.4/Scenario 1
Page 10 of 18
STEP 7: [STEP 5] FAX Appendix A to the ODS. (No. pre
programmed or 5-751-8620.)
STANDARD: Appendix A is placed in the fax machine and transmission
simulated.
- CUE: Do NOT allow fax to be transmitted. UNSAT
COMMENTS:
+
CAUTION If there is any possibility of a radiological release, do
not send personnel into areas of unknown radiological
conditions without first contacting Radiological Control
(RADCON).
STEP 8: [STEP 6] NOTIFY Security (CAS) that assembly and CRITICAL
STEP
accountability is to be conducted.
STANDARD: The performer notifies Security that assembly and
accountability is to be conducted.
This step is critical to ensure assembly card readers
UNSAT
are enabled.
- CUE: (Booth Operator) Role play as the Security and repeat
back the report.
COMMENTS:
"**ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Admin A.4/Scenario 1
Page 11 of 18
of 18 1
EVALUATOR NOTE Steps 9, 10, and 11 are all part of the same Admin11A.4lScenario
Page
procedure step.
+
STEP 9: [STEP 7] ANNOUNCE to the plant: "ATTENTION ALL CRITICAL
SITE PERSONNEL. ATTENTION ALL SITE PERSONNEL. STEP
AN Site Area Emergency has been declared based on EAL
1.2.3 "Steam Generator Tube Rupture" and EAL 1.3.4 SAT
"Containment Bypass." All personnel report to your
assembly areas for accountability. Staff the TSC and OSC.
(Repeat)
UNSAT
STANDARD: A public address announcement for Plant Emergency
Response Personnel to staff the TSC and OSC is made
over the plant paging system. Wording describing the event
may vary.
Step is critical to alert all plant personnel of the REP
declaration and instructions staffing TSC and OSC and
alert all plant personnel to assembly areas for
accountability.
COMMENTS:
-I-
STEP 10: [STEP 7] SOUND assembly alarm AND CRITICAL
STEP
STANDARD: The performer pushes assembly alarm "EVAC AUTO" or
"EVAC MANUAL" push button.
This step is critical to activate assembly &
accountability alarm.
UNSAT
COMMENTS:
I ____________________________________
"**ltalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Admin A.4/Scenario 1
Page 12 of 18
STEP 11: [STEP 7] INITIATE WBN EPIP-8, "Personnel CRITICAL
Accountability and Evacuation". STEP
STANDARD: The performer refers to EPIP-8, Appendix C, to determine
actions necessary for personnel accountability and SAT
evacuation.
This step is critical in that specific guidance is given
with regard to assembly & accountability.. UNSAT
- CUE: After the performer has determined which sections of
EPIP-8 apply, direct him/her to return to EPIP-4 and
continue actions.
COMMENTS:
STEP 12: [STEP 8] CALL RADCON Lab and SAY: "We are in a Site CRITICAL
Area Emergency, implement WBN EPIP-14, and CECC STEP
EPIP-9."
STANDARD: The RADCON Lab is notified to implement WBN EPIP-14 SAT
and CECC EPIP-9.
This step is critical to notify RADCON so proper
survey's, etc. are implemented. UNSAT
- CUE: (Booth Operator) Acknowledge the request to
implement WBN EPIP-14 and CECC EPIP-9.
COMMENTS:
"**ItalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Admin A.4/Scenario 1
Page 13 of 18
STEP 13: [STEP 9] IF there are personnel injuries, IMPLEMENT
WBN EPIP-10, "Medical Emergency Response."
STANDARD: Performer determines that it is NOT necessary to SAT
implement EPIP-10.
- CUE: Inform the performer that there are NO personnel
UNSAT
injuries.
COMMENTS:
i
STEP 14: [STEP 10] IF there is a security threat, IMPLEMENT WBN
EPIP-11, "Security and Access Control."
STANDARD: Performer determines that it is NOT necessary to
implement EPIP-1 1.
- CUE: Inform the performer that there has been NO reports UNSAT
of a security threat
COMMENTS:
STEP 15: [STEP 11] NOTIFY Duty Plant Manager, and PROVIDE CRITICAL
Appendix A information (SEE duty list for telephone STEP
numbers). The Duty Plant Manager will call the Plant
Manager or alternate.
STANDARD: Duty Plant Manager is provided the Appendix A information.
This step is critical as it alerts plant management to
REP activation. UNSAT
- CUE: (Booth Operator) Role play as the Duty Plant Manager
and acknowledge the report.
COMMENTS:
j _____________________
"**ltalicizedCues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Admin A.4/Scenario 1
Page 14 of 18
STEP 16: [STEP 12] EVALUATE the need to implement EPIP-16,
"Initial Dose Assessment for Radiological Emergencies," for
a dose projection if radioactivity is being released through
normal plant release paths. SAT
STANDARD: The performer determines whether or not EPIP-16 is to be
implemented. Either decision is acceptable.
UNSAT
- CUE: (Booth Operator) If RADCON is notified to implement
EPIP-16, acknowledge the report.
COMMENTS:
NOTE NRC notification should be made as soon as
practicable but within one hour of "SITE AREA
EMERGENCY" declaration. Whenever NRC requests, a
qualified person must provide a continuous update to
NRC Operations Center. The following commercial
numbers are for the NRC Operations Center.
9-1-301-816-5100 (MAIN)
9-1-301-951-0550 (BACKUP)
9-1-301-816-5151 (FAX)
EVALUATOR NOTE: DO NOT allow actual call to NRC. Ensure call is
to simulator instructor.
STEP 17: [STEP 13] NOTIFY the NRC, using designated NRC CRITICAL
phone (ENS), of plan activation. STEP
STANDARD: The NRC is notified of plan activation using designated
line. SAT
This step is critical as it alerts NRC to REP activation.
EVALUATOR NOTE: DO NOT allow actual call to NRC. Ensure call is UNSAT
to simulator instructor.
- CUE: (Booth Operator) Role play the NRC and acknowledge
the report.
COMMENTS:
"Italicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Admin A.4/Scenario 1
Page 15 of 18
STEP 18: [STEP 14] NOTIFY the NRC Resident Inspector by calling CRITICAL
1776 and PROVIDING the information on Appendix A. STEP
STANDARD: The NRC Resident Inspector is provided Appendix A SAT
information.
This step is critical as it alerts NRC to REP activation.
UNSAT
EVALUATOR NOTE: DO NOT allow actual call to NRC Resident.
Ensure call is to simulator instructor.
- CUE: (Booth Operator) Role play the NRC Resident and
acknowledge the report.
COMMENTS:
EVALUATOR CUE: State to applicant that conditions have now
changed. A General Emergency has been
declared.
EVALUATOR CUE: Read and provide Applicant handout sheet
and equation sheet for PAR
recommendations.
STEP 19: Refers to EPIP-5 to Appendix B "Protective Action SAT
Recommendation Guidance.
STANDARD: Applicant obtains copy of EPIP-5 Appendix B. UNSAT
COMMENTS:
"**Italicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Admin A.4/Scenario 1
Page 16 of 18
STEP 20: General Emergency Declarn..d. SAT
STANDARD: Applicant enters logic tree a t top of page since general
emergency has been declar ed. (given in applicant's UNSAT
handout sheet.
COMMENTS:
STEP 21: Is Projected or Measured Dose Greater Than or Equal to CRITICAL
Table 1 Limits at or beyond 5 miles. STEP
STANDARD: Applicant determines that dose exceeds table 1 limits (1 SAT
REM/hr external dose) at 5 miles or beyond, therefore
applicant answers YES to logic question. Applicant then
determines that the logic indicates Recommendation 1 as
the Protective Action Recommendation. UNSAT
Applicant calculates dose at 5 miles using point source
equation:
I1(d1 )2= 2(2)2 2
2
800mr./hr(7mi) = 12 (5mi)
12 = 39200/25 = 1568 mr/hr = 1.568 R/hr
(external dose rate at 5 miles)
This step is critical for making the appropriate PAR to
the CECC.
- CUE: Acknowledge report by the applicant
COMMENTS:
END OF TASK
.1_____________________
TIME STOP:
"**ltalicized Cues Are To Be Used Only If JPM PerformanceIs Being Simulated.
Page 17 of 18
APPLICANT CUE SHEET
(TO BE RETURNED TO EXAMINER UPON COMPLETION OF TASK)
DIRECTION TO TRAINEE:
I will explain the initial conditions, and state the task to be performed. All control
room steps shall be performed for this JPM, including any required
communications. I will provide initiating cues and reports on other actions when
directed by you. Ensure you indicate to me when you understand your assigned
task. To indicate that you have completed your assigned task return the handout
sheet I provided you.
INITIAL CONDITIONS:
Simulator represents the current plant conditions.
Simulator operation is frozen.
INITIATING CUES:
Using the current conditions, make the initial classification of the event per the
REP and make the required notifications.
THIS IS A TIME CRITICAL TASK
Page 18 of 18
APPLICANT HANDOUT SHEET
(TO BE RETURNED TO EXAMINER UPON COMPLETION OF TASK)
NEW CONDITIONS:
"* Chemistry reported RCS activity is now 350 [tci/gm dose equivalent Iodine
131
"* A radiological field team reported that measured external dose at 7 miles
from the plant is 800 mr/hr.
A General Emergency has been declared.
INITIATING CUES:
Make the Protective Action Recommendations for this declaration. When
determining 2 and 5 mile dose rates, assume that these readings are measured
from a point source at the plant. (Ignore all atmospheric conditions that would
affect measurements)
EQUATIONS
0Q= ficpAT p = Pý 10 SUR(t)
Q = iicpAh p= = 0 e th
S
Q=UAAT SCR= (I1- Keff)
2 6 .0 6Qeff P) CR 2
SUR CR= (1-Keffl)- CR1
(H-p)
SR=26.06 M= (1- Keffi)
SUR= (Kefr2)
M(1-
p ( ,f- 1) (1- Keff)
=
AKff
P- Keff 11(dl)= 12 (d 2 )
S= + (1-p)1 I,(dj) 2 = 12(d2)
2
"P L keffpi
I X 10-4 seconds Wpump'= liiAPv
Net Work (out)
keff = .01 seconds' Cycle Efficiency = Energy (in)
CONVERSIONS
1 Curie = 3.7 x 1010 dps 1 kg = 2.21 Ibm
1 hp = 2.54 x 103 Btu/hr 1 MW = 3.41 x 106 Btu/hr
OF = 9/5 OC + 32
I Btu = 778 ft-lbf
°C = 5/9 (OF - 32)