ENS 50025: Difference between revisions

v t e ENS Event
07:00 Apr 10, 2014
Title	Part 21 - Barton Model 288A and 289A Differential Pressure Switch Defect
Event Description	{{#Wiki_filter:Cameron Measurement Systems is reporting a defect affecting versions of the Barton Model 288A and 289A differential pressure indicating switches and spare switch assemblies for these products. The defect being reported is an out of specification concentricity issue with the roller that actuates the switches. This represents a switch setpoint repeatability concern. Any additional safety significant issues that might be identified in our ongoing investigation will be addressed in subsequent advisories that will be published. If you have any questions please contact Chuck Rogers, Director of Quality and Safety, at (281) 582-9507 or Jim Greer, Engineering Manager, at (800) 291-3550. * * UPDATE AT 1626 EDT ON 6/9/2014 FROM CHUCK ROGERS TO MARK ABRAMOVITZ * * * The following information was excerpted from an e-mail: Cameron has performed switch setpoint repeatability testing which has verified that rollers, even those with out of tolerance run-out, can meet the published 0.25% repeatability specification as long as the roller moves freely along the switch operating cam. However, if the roller were to 'skid' or 'skip' on the cam, or rotate when the roller is off the cam due to vibrations such that the roller does not return to the exact same radial position when it's on the cam at the switch setpoint there may be a setpoint shift unless the roller has no run-out. A change in the switch setpoint could be as much as �0.32% even for the current run-out specification of 0.0003 inches. As such, given that Cameron could ship product with switch repeatability verified to be 0.25% during production testing and that an additional 0.32% could be possible due to the allowable roller run-out, a field performance of 0.57% is possible. Given wear and other uncertainties Cameron would recommend that a user consider a conservative field repeatability value for switch setpoint calculations. An important piece of information that was gleaned from the current testing effort is that switch repeatability testing is very dependent on the sensitivity of the calibration equipment utilized. Most calibration pressure sources and measurement displays have lags in the indication of the actual pressures applied that can cause errors and, even more critical, is the lag that occurs between the operator's response to the indication of the switch trip and the reading of the pressure source display. Cameron discovered that the observation of the indicator pointer (properly calibrated) is more accurate in verification of switch repeatability than any pressure source and electrical switch contact monitoring device we utilized. Once the switch setpoint is established, a pencil mark at this trip point on the indicator scale can be utilized to verify subsequent trip points. In conversations with customers that called to discuss the original Advisory concerns, Cameron became aware that some users may believe that the Model 288A and 289A switch performance is not impacted by changes in the environment where they are located. The Barton qualification for these products was a radiation augmented mild environment test program. A sample of products was exposed to 3 Mrads of radiation and then subjected to a 12G maximum seismic simulation. The products performed within specification for this limited testing at standard factory environmental conditions. In our opinion, field calibrations and switch setpoint testing should be performed at the same temperature conditions as expected when the instruments are required to perform their safety functions. Performance testing at one temperature may not necessarily ensure appropriate performance at another temperature. If you have any questions, want to place an order for a replacement instrument, switch actuation arm (with roller) or a switch and plate assembly, or want to begin the RMA process for an instrument factory repair please contact Mabel Loo, Customer Service Manager, Cameron Measurement Systems, City of Industry, CA at (800) 291-3550. Notified the R1DO (Dental), R2DO (Freeman), R3DO (Daley), R4DO (Werner), and Part-21 Group (via e-mail). }}

ENS 50025 +/-
Where
Cameron Measurement Systems Industry, California (NRC Region 4)
Organization:	Cameron Measurement Systems
Reporting

10 CFR 21.21(d)(3)(i), Failure to Comply or Defect
Time - Person (Reporting Time:+13.35 h0.556 days <br />0.0795 weeks <br />0.0183 months <br />)
Opened:	Chuck Rogers 20:21 Apr 10, 2014
NRC Officer:	Charles Teal
Last Updated:	Jun 9, 2014
50025 - NRC Website
v • d • e

v t e Emergency Notification System
Cameron Measurement Systems with 10 CFR 21.21(d)(3)(i), Failure to Comply or Defect
WEEKMONTHYEAR2014-09-09T07:00:00 [Table view]
[ENS list for Cameron Measurement Systems]

@@ Line 16: / Line 16: @@
 | event date = 04/10/2014 PDT
 | last update date = 06/09/2014
-| title = Part 21 - Barton Model 288A And 289A Differential Pressure Switch Defect
+| title = Part 21 - Barton Model 288A and 289A Differential Pressure Switch Defect
 | event text = Cameron Measurement Systems is reporting a defect affecting versions of the Barton Model 288A and 289A differential pressure indicating switches and spare switch assemblies for these products. The defect being reported is an out of specification concentricity issue with the roller that actuates the switches. This represents a switch setpoint repeatability concern.
 Any additional safety significant issues that might be identified in our ongoing investigation will be addressed in subsequent advisories that will be published. If you have any questions please contact Chuck Rogers, Director of Quality and Safety, at (281) 582-9507 or Jim Greer, Engineering Manager, at (800) 291-3550.

ENS 50025: Difference between revisions

Latest revision as of 20:50, 1 March 2018

Navigation menu

ENS 50025: Difference between revisions

Latest revision as of 20:50, 1 March 2018

Navigation menu

Search