ML063000265

Core Operating Limits Reports for Unit 1, Cycle 18, Revision 3 and Unit 2, Cycle 16, Revision 1

ML063000265
Person / Time
Site:	Calvert Cliffs
Issue date:	10/24/2006
From:	Spina J Calvert Cliffs, Constellation Energy Group
To:	Document Control Desk, Office of Nuclear Reactor Regulation
References
Download: ML063000265 (53)

Text

James A. Spina Vice President Calvert Cliffs Nuclear Power Plant, Inc.

1650 Calvert Cliffs Parkway Lusby, Maryland 20657 410.495.4455 410.495.3500 Fax Constellation Energy-Generation Group October 24, 2006 U. S. Nuclear Regulatory Commission Washington, DC 20555 ATTENTION:

Document Control Desk

SUBJECT:

Calvert Cliffs Nuclear Power Plant Unit Nos. 1 & 2; Docket Nos. 50-317 & 50-318 Core Operating Limits Reports for Unit 1, Cycle Cycle 16. Revision 1 18, Revision 3 and Unit 2, Pursuant to Calvert Cliffs Nuclear Power Plant Technical Specification 5.6.5, the attached Core Operating Limits Reports for Unit 1, Cycle 18, Revision 3 (Attachment 1) and Unit 2, Cycle 16, Revision 1 (Attachment 2) are provided for your records.

Please replace the Unit 1 Core Operating Limits Report in its entirety, with the attached Revision 3 and Unit 2 Core Operating Limits Report in its entirety, with the attached Revision 1.

Should you have questions regarding this matter, please contact Mr. Jay S. Gaines at (410) 495-4922.

Very truly yours, JAS/CAN/bj d Attachments:

(1)

(2)

Core Operating Limits Report for Unit 1, Cycle 18, Revision 3 Core Operating Limits Report for Unit 2, Cycle 16, Revision 1 cc:

Resident Inspector, NRC (Without Attachment)

P. D. Milano, NRC S. J. Collins, NRC R. I. McLean, DNR

ATTACHMENT (1)

CORE OPERATING LIMITS REPORT FOR UNIT 1, CYCLE 18, REVISION 3 Calvert Cliffs Nuclear Power Plant, Inc.

October 24, 2006

Coruýýalatlmon Enerq7,o Calvert Cliffs Nuclear Power Plant, Inc.

Core Operating Limits Report (COLR)

Unit I Cycle 18 Revision 3

/ 0 /,ý Aq d Effective Date:

17m SŽ t¶R&~~el~ ~.4Lt.~L~A%

Io/j(/0o2 RESPONSIBLE ENGINEER

/

DATE Ilk, t A,

/dC. /1 /c) d PRINCJPA L'ENdfiNEER -FOSU

/ DATE Cal~vert Cliffq 1. Cycle 1 R COI.R Pv f

Pnge. 1 of ?.

R ev I I

CORE OPERATING LIMITS REPORT CALVERT CLIFFS UNIT 1, CYCLE 18 The following limits are included in this Core Operating Limits Report:

-Specification Title Page 3.1.1 3.1.3 3.1.4 3.1.6 3.2.1 3.2.2 3.2.3 3.2.5 3.3.1 3.9.1 Introduction........................................................................................................

4 Definitions.....................

5 Shutdown Margin (SDM).......................................................................................

6 Moderator Temperature Coefficient (MTC)...............................................

6 Control Element Assembly (CEA) Alignment...........................................................

6 Regulating Control Element Assembly (CEA) Insertion Limits............... I................ 6 Linear H eat Rate (LHR ).........................................................................................

6 Total Planar Radial Peaking Factor (F,7).............

P l a n a r

~ ~ ~ ~ ~ ~ ý Ta a

e k n a t r ( x ).......................... :...................................

7 Total Integrated Radial Peaking Factor (Fr) 7 A xial Shape Index (A SI)......................................................................................

7 Reactor Protective System (RPS) Instrumentation - Operating.............................

7 B oron C oncentration............................................................................................

8 List of Approved Methodologies........................................................................

21 The following figures are included in this Core Operating Limits Report:

Number Title Page Figure 3.1.1 Figure 3.1.4 Figure 3.1.6 Figure 3.2.1-1 Figure 3.2.1-2 Figure 3.2.1-3 Figure 3.2.2 Figure 3.2.3 Figure 3.2.5 Figure 3.3.1-1 Figure 3.3.1-2 Figure 3.3.1-3 Shutdown Margin vs. Time in Cycle......................................................................

9 Allowable Time To Realign CEA Versus T

Initial Total Integrated Radial Peaking Factor (Fr)............................................

10 CEA Group Insertion Limits vs. Fraction of Rated Thermal Power........................ 11 Allowable. Peak Linear Heat Rate vs. Time in Cycle................................................

12 Linear Heat Rate Axial Flux Offset Control Limits.............................................

13 T

Total Planar Radial Peaking Factor (Fxy ) vs.

Scaling Factor (N -Factor)....................................................................................

14 T

Total Planar Radial Peaking Factor (Fy ) vs. Allowable Fraction of Rated T herm al Pow er.....................................................................................................

15 T

Total Integrated Radial Peaking Factor (F, ) vs.

Allowable Fraction of Rated Thermal Power......................................................

16 DNB Axial Flux Offset Control Limits................................................................

17 Axial Power Distribution - High Trip Setpoint Peripheral Axial Shape Index vs. Fraction of Rated Thermal Power...................

18 Thermal Margin/Low Pressure Trip Setpoint - Part 1.......................................... 19 Thermal Margin/Low Pressure Trip Setpoint - Part 2.........................................

20 Calvert Cliffs 1 Cycle 18 COLR Paae 2 of 25 Rev. 3 1

UNIT 1 CORE OPERATING LIMITS REPORT LIST OF EFFECTIVE PAGES Page No.

Rev. No.

1 3

2 3

3 3

4 3

5 3

6 3

7 3

8 3

9 3

10 3

11 3

12 3

13 3

14 3

15 3

16 3

17 3

18 3

19 3

20 3

21 3

22 3

23 3

24 3

25 3

Calvert Cliffs 1. Cycle 18 COLR Pane 3 of 25 Rev. 3 1

INTRODUCTION This report provides the cycle-specific limits for operation of Calvert Cliffs Unit 1, Cycle 18. It' contains the limits for:

Shutdown Margin (SDM)

Moderator Temperature Coefficient (MTC)

Control Element Assembly (CEA) Alignment Regulating Control Element Assembly (CEA) Insertion Limits Linear Heat Rate (LHR)

Total Planar Radial Peaking Factor (FxyT) T Total Integrated Radial Peaking Factor (Fr)

Axial Shape'Index (ASI)

Reactor Protective System (RPS) Instrumentation - Operating Boron Concentration In addition, this report contains a number of figures which give limits on the parameters listed above. If any of the limits contained in this report are exceeded, corrective action will be taken as defined in the Technical Specifications.

This report has been prepared in accordance with the requirements of Technical Specifications.

The cycle specific limits have been developed using the NRC-approved methodologies given in the "List of Approved Methodologies" section of this report and in the Technical Specifications.

COLR Revision 0 Initial release of the Unit 1 Cycle 18 (U1C18) COLR per Safety Evaluation SE00497 Rev. 0. UlC18 is only allowed to operate in Mode 6 or in a defueled condition. Although U1C18 is only authorized to enter Mode 6, limits presented within this COLR relate to some parameters only applicable to operation in higher plant modes.

COLR Revision 1 Revised to now allow operation of U1C 18 in plant modes 5, 6, or defueled per SE00497 Rev. 1. Although U1 C18 is only authorized to enter Modes 5 and 6, limits presented within this COLR relate to some parameters only applicable to operation in higher plant modes.

COLR Revision 2 Revised to now allow operation of U1C18 in all plant modes per SE00497 Rev. 2.

COLR Revision 3

. Revised Figure 3.2.1-3 (N-Factor) as part of the corrective action for IRE-017-571.

Calvert Cliffs 1, Cycle 18 COLR Pa~e 4 of 25 Rev.3 I

DEFINITIONS Axial Shape Index (ASI)

ASI shall be the power generated in the lower half of the core less the power generated in the upper half of the core, divided by the sum of the power generated in the lower and upper halves of the core.

ASI = lower-upper YE lower + upper The Axial Shape Index (YI) used for the trip and pretrip signals in the Reactor. Protection System (RPS) is the above value (YE) modified by an appropriate multiplier (A) and a constant (B) to determine the true core axial power distribution for that channel.

Y, = AYE + B Total Integrated Radial Peaking Factor - FrT The Total Integrated Radial Peaking Factor is -the ratio of the peak pin power to the average pin power in an unrodded core.

Total Planar Radial Peaking Factor - FxyT The Total Planar Radial Peaking Factor is the maximum ratio of the peak to average power density of the individual fuel rods in any of the unrodded horizontal planes.

Calvert Cliffs L Cycle 18 COLR Pane 5 of 25 Rev.3 I

Calvert C1 Iffs I - Cvc1e 18 COLR Paee 5 of 25 Rev. 3 1

CYCLE SPECIFIC LIMITS FOR UNIT 1, CYCLE 18 3.1.1 Shutdown Margin (SDM) (SR 3.1.1.1)

Tavg > 200 'F - Modes 3 and 4:

The shutdown margin shall be equal to or greater than the limit line of COLR Figure 3.1.1.

Tavg *200 'F-Mode 5:

The shutdown margin shall be > 3.0% Ap.

3.1.3 Moderator Temperature Coefficient (MTC) (SR 3.1.3.2)

The Moderator Temperature Coefficient (MTC) shall be less negative than -3.0 x 10 4 Ap/F at rated thermal power.

3.1.4 Control Element Assembly (CEA) Alignment (Action 3.1.4.B.1)

The allowable time to realign a CEA may be provided by the full core power distribution monitoring system (Better Axial Shape Selection System - BASSS) or COLR Figure 3.1.4, "Allowable Time to Realign CEA Versus Initial Total Integrated Radial Peaking Factor (FrT). If COLR Figure 3.1.4 is used, the pre-misaligned Fr value used to determine the allowable time to realign the CEA shall be the latest measurement taken within 5 days prior to the CEA misalignment. If no measurements have been taken within 5 days prior to the misalignment and the full core power distribution monitoring system is unavailable then the time to realign is zero (0) minutes.

3.1.6 Regulating Control Element Assembly (CEA) Insertion Limits (SR 3.1.6.1 and SR 3.1.6.2)

The regulating CEA groups insertion limits are shown on COLR Figure 3.1.6.

3.2.1 Linear Heat Rate (LHR) (SR 3.2.1.2 and SR 3.2.1.4)

The linear heat rate shall not exceed the limits shown on COLR Figure 3.2.1-1.

The axial shape index power dependent control limits are given in COLR Figure 3.2.1-2.

0 When using the excore detector monitoring system (SR 3.2.1.2):

The alarm setpoints are equal to the ASI limits; therefore when the alarms are adjusted, they provide indication to the operator that ASI is not within the limits.

The axial shape index alarm setpoints are shown as a function of fraction of thermal power on COLR Figure 3.2.1-2. A scaling factor (N-Factor) vs. FxyT is shown in COLR Figure 3.2.1-3. The fraction of thermal power shown in COLR Figure 3.2.1-2 must be scaled by the N-Factor to determine the axial shape index alarm setpoints as a function of fraction of rated thermal power.

Calvert Cliffs I. Cycle 18 COLR Pasie 6 of 25 Rev. 3 1

CYCLE SPECIFIC LIMITS FOR UNIT 1, CYCLE 18 When using the incore detector monitoring system (SR 3.2.1.4):

The alarm setpoints are adjusted to protect the Linear Heat Rate limits shown on COLR Figure 3.2.1-1 and uncertainty factors are appropriately included in the setting of these alarms.

The uncertainty factors for the incore detector monitoring system are:

1.

A measurement-calculational uncertainty factor of 1.062,

2.

An engineering uncertainty factor of 1.03,

3.

A linear heat rate uncertainty factor of 1.002 due to axial fuel densification and thermal expansion, and 4.a For measured thermal power less than or equal to 50 percent but greater than 20 percent of rated full core power a thermal power measurement uncertainty factor of 1.035.

4.b For measured thermal power greater than 50 percent of rated full core power a thermal power measurement uncertainty factor of 1.020.

3.2.2 Total Planar Radial Peaking Factor (FxyT) (SR 3.2.1.1 and SR 3.2.2.1)

The calculated value of FXYT shall be limited to < 1.70.

The allowable combination of thermal power, CEA position, and FxyT are shown on COLR Figure 3.2.2.

3.2.3 Total Integrated Radial Peaking Factor (Fr T) (SR 3.2.3.1)

The calculated value of FrT shall be limited to < 1.65.

The allowable combinations of thermal power, CEA position, and FrT are shown on COLR Figure 3.2.3.

.3.2.5 Axial Shape Index (ASI) (SR 3.2.5.1)

The axial shape index and thermal power shall be maintained within the limits established by the Better Axial Shape Selection System (BASSS) for CEA insertions of the lead bank of

< 55% when BASSS is operable, or within the limits of COLR Figure 3.2.5 for CEA insertions specified by COLR Figure 3.1.6.

3.3.1 Reactor Protective System (RPS) Instrumentation - Operating (Reactor Trip Setpoints) (TS Table 3.3.1-1)

The Axial Power Distribution - High trip setpoint and allowable values are given in COLR Figure 3.3.1-1.

The Thermal Margin/Low Pressure (TM/LP) trip setpoint is given in COLR Figures 3.3.1-2 and 3.3.1-3. The allowable values are to be not less than the larger of (1) 1875 psia or (2) the value calculated from COLR Figures 3.3.1-2 and 3.3.1-3.

Calvert Cliffs 1. Cycle 18 COLR Page 7 of 25 Rev.3 I

Calvert Cliffs I - Cvcle 18 COLR Page 7 of 25 Rev. I I

3.9.1 Boron Concentration (SR 3.9.1.1)

The refueling boron concentration will maintain the kff at 0.95 or less (including a 1% Ak/k conservative allowance for uncertainties). The refueling boron concentration shall be maintained uniform. For Mode 6 operation the RCS temperature must be maintained< 140 OF.

The "0 Credited CEAs" requirement (Option 2 or 3) shall apply for all Post-Refueling Upper Guide Structure or Reactor Vessel Head Lifts of more than 12 inches.

Note Option 1 is the designated refueling boron concentration for U1C18. The Control Room Shift Manager or Control Room Supervisor shall contact both Chemistry and Nuclear Fuel Services prior to implementing one of the other refueling boron concentration options to confirm all affected groups have appropriate controls in place.

Refueling Boron Concentration Limits Option I Option 2 Option 3 Zr 11-1p Zerof B1-11) nB1111)- Zero

'24 rQedilc 0 Cr~edied CE.A 0~ rvedileq CE. k Post-Refueling UGS or

<12 inches No restriction No restriction RV Head lift height 1

restrictions.

COLR/Tech Spec Limit 2264 ppm 2396 ppm 2396 ppm Chemistry Sampling 23 ppm 24 ppm 24 ppm Boron-10 Depletion 47 ppm 50 ppm 50 ppm Refueling Boron Concentration

>2334 ppm

> 2470 ppm

> 2470 ppm Limit including Chemistry Sampling uncertainty and Boron-10 Depletion Dilution of the Refueling Pool between Low and 73 ppm 78 ppm 78 ppm High Level Alarms with Refueling Pool Flooded Any number of Temporary An allowance of 20 An allowance of 20 An allowance of 20 ppm is Rotations of Fuel ppm is already included ppm is already included already included in the Assemblies in the above in the above above COLRiTech Spec COLRiTech Spec Limit COLR/Tech Spec Limit Limit An allowance of 50 An allowance of 50 An allowance of 50 ppm is U1C18 Allowance for ppm is already included ppm is already included already included in the Holes in the Pattern in the above in the above above COLRiTech Spec COLR/Tech Spec Limit COLR/Tech Spec Limit Limit Refueling Boron Concentration Administrative Limit

> 2407 ppm

> 2548 ppm

> 2548 ppm (Note 1)

Note:

(1)

The above table specifies the minimum technical requirements. It is acceptable forNEOP-13 to conservatively list higher ppm values.

Calved Cliffs I. Cycle 18 COLR Pane 8 of 25 Rev.3 I

CnIvert Cliffs I - Cvcle 18 COLR Page 9 of 25 Rev-I I

6 5 A 4

o 8-0 Iii z *3 z

0 2 I-(jD I

ACCEPTABLE OPERATION (EOC, 4.5)

REGION (BOC, 3.5)

MINIMUM SHUTDOWN MARGIN UNACCEPTABLE OPERATION REGION

-I

-l 1.

0 BOC EOC TIME IN CYCLE Figure 3.1.1 Shutdown Margin vs. Time in Cycle

(>~1verf(71iff'~ 1Cvcle IXCOIR PaQe 9 of 25 Rev.3 I

Cqlvert Cfiffq I CvcIe 18 C01,R Page 9 of 25 Rev. 31

70 60 (1.53,60) 50 COr)

ILl I--

z N

40

<978 600FrT U.I z

30 CD O

20 w

10 ALLOWED REGION 0

(1.63,0)

I I I

I I

I I

I I

I I

III I

I I

I I

1.50 1.55 1.60 1.65 1.70 MEASURED PRE-MISALIGNED TOTAL INTEGRATED RADIAL PEAKING FACTOR Figure 3.1.4 Allowable Time to Realign CEA Versus Initial Total Integrated Radial Peaking Factor (Fr)

Calvert Cliffs 1. Cycle 18 COLR Paae 10 of 25 Rev. 31

(1.00 FRTP, Group 5 @ 35% Inserted)

W

.I--

0.

W I,

I--

LL 0

z0 1.000 (0.90 FRTP, Group

@ 35% Inserted)

'0.900.

080j(0.1 5 FRTP, Grou-p-5@ a-5-0%flý,nserted),

00(0.70 FRTP, Group 5 @ 60/0 Inserted) 0.700

}.... -........ ]..-:.- £ (0651FRTP, group 5 @85% In 0.600

.*-:b 0

~.-

(0.56 FRTPGroup4 0.500 -

0.

0.400 0.300 $ 3/4 i1 P0.200 ZPP DII

-erted)d REG ION

........ UAC :E-- BL.......

Transient Inse ion (0.20 FRTP, Group 3 @ 60% Inse ed)

(Aboveiero Power PDILSetpoint Group 3&@60% nseded)

,i ns, ted)

R UetpomTt UP 5 REGUATIG GRUP I

REGLATIG GROP I I

0%

135" 1

20%

108" I

I

.1 40%

60%

80%

81" 54" 27" I

I 100%

0%

0" 135' 1

20%

108" 1

40%

81" 1

60%

54" I

I I

80%

100%

0%

2T' 0"

135" 1

20%

108" 1

40%

81" 1

60%

54" I

I 80%

100%

27" 0"

REGLATNGGROP F-RGULAINGGROU 2

0%

135" I

1 1

20%

40%

60%

108" 81" 54" I

1 80%

100%

0%

27" 0"

135" 1

1 20%

40%

108".

81" I

I 60%

80%

54" 27" I

100%

0"

%CEA INSERTION INCHES CEA WITHDRAWN (ARO is defined in NEOP-13)

Figure 3.1.6 CEA Group Insertion Limits vs. Fraction of Rated Thermal Power Calvert Cliffs 1. Cycle 18 COLR Page I I of 25 Rev. 3 1

17.0 16.5

• 1 i

F I--

U-I--

_w

,Ile

,_1 0

-J

-O 16.0 0

155 00

+ 15.0

-CC

-,1

+

-jW 14.5

• -14.3 14.0 13.5 13.0 UNACCEPTABLE OPERA-RON ACCEPTABLE OPERATION BOC EOC TIME IN CYCLE Figure 3.2.1-1 Allowable Peak Linear Heat Rate vs. Time in Cycle Calvert Cliffs 1. Cycle 18 COLR Page 12 of25 Rev.3 I Calvert Cliffs 1. Cvcle 18 C01,R Page 12 of 25 Rev. 3 1

1.10 1.05 1.00 0.95 0.90

, 0.85

,LI

ý 0.80 0

0.75 2 0.70 W

,LU 0.65 o 0.60 z0 0.55 05 00.50

'"0.45 0.40-0.35 0.30 0.25

(-0.42, 0.20).

(0.3, 0.20) 0.20

-0.60

-0.40

-0.20 0.00 0.20 0.40 PERIPHERAL AXIAL SHAPE INDEX, Y Figure 3.2.1-2 Linear Heat Rate Axial Flux Offset Control Limits (LCO Limits are not needed below 20% thermal power per SE00433)

(See NEOP-13 for Administrative Limits) 0.60 Calvert Cliffs 1. Cycle 18 COLR Paee 13 of25 Rev. 3 Calvert Cliffs 1. Cvcle 18 COLR Paae 13 of 25 Rev. 3

1.00 0.90

£ 0.80 0I--

U,.

0.70 0I-0.60 U-z 0.50 CO, 0.40 0.30 0.20 I

i I

I I

I I

I I

M 1.35 1.40 1.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 FxyT Figure 3.2.1-3 Total Planar Radial Peaking Factor (FxyT) vs.

Scaling Factor (N-Factor)

(See NEOP-13 for Administrative Limits)

C21v~.rtC11ff~ 1 Cycle. iX C'OI.R P~ee 14 of9~

Rev C.nlvf-.rt C.] iffq I Cvnle. I R C(-)T.R Pnoe 14 nf ?ý R Pv I I

1.05 0.95 --

'-*A*=

r 09 (1.70, 1.00)

REGI LU REGION CL 0.85

_1 07(1.785, 0.8)

W* 0 Fxm LIMIT CURVE I-

, 0.65 I. 0.55 0z 0

i-0.45-U- 0.35 --

ACCEPTABLE

-j OPERATION OREGION S0.25-31 (1.874, 0.20).

-j 0.15 0.05 1.60 1.65 1.70 1.75 1.80 1.85 1.90 F T Figure 3.2.2 Total Planar Radial Peaking Factor (Fxy7T vs.

Allowable Fraction of Rated Thermal Power While operating with F16T greater than 1.70, withdraw CEAs to or above the Long Term Steady State Insertion Limits (Figure 3.1.6)

C'21vert Cliff'q 1 C.vc,](e, 1RCOT.RPae1 fSRv I

Pae, 1 of f2.5 Rev-I I

1.05 IY

~UINA~UtjI-I bAI:bLI'

, 0.95 OPERATION 0

REGION 0.85 m

0.85 (1.7325, 0.80)

LU 0.75-cT

~FrT LIMIT CURVE 0.65 U" 0.55 0z O 0.45 ACCEPTABLE 0.4 OPERATION REGION u.0.35-

-j 0.25 0

(1.819, 0.20) 0.15 I,.

0.05 1.60 1.65 1.70 1.75

% 1.80 1.85 FrT Figure 3.2.3 Total Integrated Radial Peaking Factor (FrT) VS.

Allowable Fraction of Rated Thermal Power While operating with FrT greater than 1.65, withdraw CEAs to or above the Long Term Steady State Insertion Limits (Figure 3.1.6)

Cnlvert Cliff-, I_ Cvcle 18 COLR Paize 16 of 25 Rev. 3 1

.-j ILl w

LIJ

-J Lu 0~

UL

-J 0

.J 41 4:)

0 z

0 0

U, 9

LL 1.10-1.05 1.00 0.95 0.90 0.85 0.80 0.75 0.70 0.65 0.60 0.55 0.50 0.45 0.40 0.35 0.30 0.25 0.204-

-0.60

-0.40

-0.20 0.00 0.20 0.40 0.60 PERIPHERAL AXIAL SHAPE INDEX, Y Figure 3.2.5 DNB Axial Flux Offset Control Limits (LCO Limits are not needed below 20% thermal power per SE00433)

(See NEOP-13 for Administrative Limits)

Calved Cliffs 1. Cycle 18 COLR Pane 17of25 Rev.3 I

Calvert. Cliff-I - Cvcle 18 COLR Pacie 17 of 25 Rev-3 1

W LU 3-1 0

(-

I-13 w

LI I-0 z0 LL

.1.300 1.250 1.200 1.150 1.100 1.050 1.000 0.950 0.900 0.850 0.800 0.750 0.700 0.650 0.600 0.550 0.500 0.450 0.400 0.350 0.300 0.250 0.200 0.150

-0.80

-0.60

-0.40

-0.20 0.00 0.20 0.40 PERIPHERAL AXIAL SHAPE INDEX, Yi 0.60 0.80 Figure 3.3.1-1 Axial Power Distribution - High Trip Setpoint Peripheral Axial Shape Index vs. Fraction of Rated Thermal Power Calvert Cliffs 1, Cycle 18 COLR Page 18 of 25 Rev.3 I

Calvert Cliffs 1, Cvcle 18 COLR Pane 18 of 25 Rev. 3

1.60 1.50 QDN* A1 x QR1 1.40 1.30 1.3)

Al

+0.17xASI +1.

1.10-A1

-0.5 xASI + 1 0 1.00 0.90

-0.60 -0.50. -0.40 -0.30 -0.20 -0.10 0.00 0.10 0.20 0.30 0.40 ASI Figure 3.3.1-2 Thermal Margin/Low Pressure Trip Setpoint - Part 1 (ASI vs. A1) 0.50 0.60

(~i1vertC.IifTh 1. C.vcle lgCOI.R Pane 19 of25 Rev 3 I Calvert. Cliffi; 1. Cvcle 18 COLR Pag*e 19 of 25 Rev-I I

1.2 1.1 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 (1.2, 1.2) 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 FRACTION OF RATED THERMAL POWER (RTP)

Figure 3.3.1-3 Thermal Margin/Low Pressure Trip Setpoint - Part 2 (Fraction of Rated Thermal Power vs. QR1 )

Calvert Cliffs 1. Cycle 18 COLR Pace 20 of 25 Rev.3 I

Calvert Cliffs I - Cvcle 18 COLR Paae 20 of 25 Rev. 3 1

LIST OF APPROVED METHODOLOGIES (1)

CENPD-199-P, Rev 1-P-A, "C-E Setpoint Methodology: C-E Local Power Density and DNB LSSS and LCO Setpoint Methodology for Analog Protection Systems," January 1986.

Additionally, Supplement 2-P-A dated June 1998. (Methodology for Specifications 3.3.1, 3.1.6, 3.2.1, 3.2.2, 3.2.3, 3.2.5)

(2)

CEN-124(B)-P, "Statistical Combination of Uncertainties Methodology Part 1: C-E Calculated Local Power Density and Thermal Margin/Low Pressure LSSS for Calvert Cliffs Units I and II,"

December 1979 (Methodology for Specifications 3.3.1, 3.1.6, 3.2.2, 3.2.3)

(3)

CEN-124(B)-P, "Statistical Combination of Uncertainties Methodology Part 2: Combination of System Parameter Uncertainties in Thermal Margin Analyses for Calvert Cliffs Units 1 and 2,"

January 1980 (Methodology for Specifications 3.3.1, 3.1.6, 3.2.3, 3.2.5)

(4)

CEN-,124(B)-P, "Statistical Combination of Uncertainties Methodology Part 3: C-E Calculated Departure from Nucleate Boiling and Linear Heat Rate Limiting Conditions for Operation for Calvert Cliffs Units 1 and 2," March 1980 (Methodology for Specifications 3.1.6, 3.2.1, 3.2.2, 3.2.3, 3.2.5)

(5)

CEN-191(B)-P, "CETOP-D Code Structure and Modeling Methods for Calvert Cliffs Units 1 and 2," December 1981 (Methodology for Specifications 3.3.1, 3.1.6, 3.2.3, 3.2.5)

(6)

Letter from Mr. D. H. Jaffe (NRC) to Mr. A. E. Lundvall, Jr. (BG&E), dated June 24, 1982, Unit 1 Cycle 6 License Approval (Amendment No. 71 to DPR-53 and SER) [Approval to CEN-124(B)-P (three parts) and CEN-191 (B)-P)]

(7)

CEN-348(B)-P, "Extended Statistical Combination of Uncertainties," January 1987 (Methodology for Specifications 3.3.1, 3.1.6, 3.2.3, 3.2.5)

(8)

Letter from Mr. S. A. McNeil, Jr. (NRC) to Mr. J. A. Tiernan (BG&E), dated October 21, 1987, Docket Nos. 50-317 and 50-318, "Safety Evaluation of Topical Report CEN-348(B)-P, Extended Statistical Combination of Uncertainties" (9)

CENPD-16.1-P-A, "TORC Code, A Computer Code for Determining the Thermal Margin of a Reactor Core," April 1986 (Methodology for Specifications 3.3.1, 3.1.6, 3.2.3, 3.2.5)

(10)

CENPD-162-P-A, "Critical Heat Flux Correlation of C-E Fuel Assemblies with Standard Spacer Grids Part 1, Uniform Axial Power Distribution," April 1975 (Methodology for Specifications 3.3.1, 3.1.6, 3.2.3, 3.2.5)

(11)

CENPD-207-P-A, "Critical Heat Flux Correlation for C-E Fuel Assemblies with Standard Spacer Grids Part 2, Non-Uniform Axial Power Distribution," December 1984 (Methodology for Specifications 3.3.1, 3.1.6, 3.2.3, 3.2.5)

(12)

CENPD-206-P-A, "TORC Code, Verification and Simplified Modeling Methods," June 1981 (Methodology for Specifications 3.3.1, 3.1.6, 3.2.3, 3.2.5)

(13)

CENPD-225-P-A, "Fuel and Poison Rod Bowing," June 1983 (Methodology for Specifications 3.3.1, 3.1.6, 3.2.3, 3.2.5)

Calvert Cliffs, 1. Cvcle 18 COLR Paize 21 of 25 Rev. 31

(14)

CENPD-266-P-A, "The ROCS and DIT Computer Code for Nuclear Design," April 1983 (Methodology for Specifications 3.3.1, 3.1.6, 3.2.1, 3.2.2, 3.2.3, 3.2.5)

(15)

CENPD-275-P-A, "C-E Methodology for Core Designs Containing Gadolinia - Urania Burnable Absorbers," May 1988 (Methodology for Specifications 3.3.1, 3.1.6, 3.2.1, 3.2.2, 3.2.3, 3.2.5)

(16)

CENPD-382-P-A, "Methodology for Core Designs Containing Erbium Burnable Absorbers," August 1993 (Methodology for Specifications 3.3.1, 3.1.6, 3.2.1, 3.2.2, 3.2.3, 3.2.5)

(17)

CENPD-139-P-A, "C-E Fuel Evaluation Model Topical Report," July 1974 (Methodology, for Specifications 3.3.1, 3.1.6, 3.2.1, 3.2.2)

(18)

CEN-161-(B)-P-A, "Improvements to Fuel Evaluation Model," August 1989 (Methodology for Specifications 3.3.1, 3.1.6, 3.2.1, 3.2.2)

(19)

CEN-161-(B)-P, Supplement 1-P, "Improvements to Fuel Evaluation Model," April 1986 (Methodology for Specifications 3.3.1, 3.1.6, 3.2.1, 3.2.2)

(20)

Letter from Mr. S. A. McNeil, Jr. (NRC) to Mr. J. A. Tiernan (BG&E), dated February 4, 1987, Docket Nos. 50-317 and 50-318, "Safety Evaluation of Topical Report CEN-161-(B)-P, Supplement 1 -P, Improvements to Fuel Evaluation Model" (Approval of CEN-161(B), Supplement l-P)

(21)

CEN-372-P-A, "Fuel Rod Maximum Allowable Gas Pressure," May 1990 (Methodology for Specifications 3.3.1, 3.1.6, 3.2.1, 3.2.2)

(22)

Letter from Mr. A. E. Scherer (CE) to Mr. J. R. Miller (NRC) dated December 15, 1981, LD-81-095, Enclosure l-P, "C-E ECCS Evaluation Model Flow Blockage Analysis" (Methodology for Specifications 3.2.1, 3.2.2)

(23)

CENPD-132, Supplement 3-P-A, "Calculative Methods for the C-E Large Break LOCA Evaluation Model for the Analysis of C-E and W Designed NSSS," June 1985 (Methodology for Specifications 3.2.1, 3.2.2 and approval of Letter LD-81-095, dated December 15, 1981)

(24)

CENPD-133, Supplement 5, "CEFLASH-4A, a FORTRAN77 Digital Computer Program for Reactor Blowdown Analysis," June 1985 (Methodology for Specifications 3.2.1, 3.2.2)

(25)

CENPD-134, Supplement 2, "COMPERC-II, a Program for Emergency Refill-Reflood of the Core," June 1985 (Methodology for Specifications 3.2.1, 3.2.2)

(26)

Letter from Mr. D. M. Crutchfield (NRC) to Mr. A. E. Scherer (CE), dated July 31, 1986, "Safety Evaluation of Combustion Engineering ECCS Large Break Evaluation Model and Acceptance for Referencing of Related Licensing Topical Reports (Approval of CENPD-133, Supplement 5 and CENPD-134, Supplement 2)

(27)

CENPD-f35, Supplement 5-P, "STRIKIN-Il, A Cylindrical Geometry Fuel Rod Heat Transfer Program," April 1977 (Methodology for Specifications 3.2.1, 3.2.2)

Calvert Cliffs 1, Cycle 18 COLR Page 22 of 25 Rev.3 I Calvert Cliffs 1. Cvcle 18 COLR Page 22 of 25 Rev. 3 1

(28)

Letter from Mr. R. L. Baer (NRC) to Mr. A. E. Scherer (CE) dated September 6, 1978, "Evaluation of Topical Report CENPD-135, Supplement 5" (29)

CENPD-137, Supplement 1-P, "Calculative Methods for the C-E Small Break LOCA Evaluation Model," January 1977 (Methodology for Specifications 3.2.1, 3.2.2)

(30)

CENPD-133, Supplement 3-P, "CEFLASH-4AS, "A Computer Program for the Reactor Blowdown Analysis of the Small Break Loss of Coolant Accident," January 1977 (Methodology for Specifications 3.2.1, 3.2.2)

(31)

Letter from Mr. K. Kniel (NRC) to Mr. A. E. Scherer (CE), dated September 27, 1977, "Evaluation of Topical Reports CENPD-133, Supplement 3-P and CENPD-137, Supplement 1-P" (32)

CENPD-138, Supplement 2-P, "PARCH, A FORTRAN-IV Digital Program to Evaluate Pool Boiling, Axial Rod and Coolant Heatup," January 1977 (Methodology for Specifications 3.2.1, 3.2.2)

(33)

Letter from Mr. C. Aniel (NRC) to Mr. A. E. Scherer, dated April 10, 1978. "Evaluation of Topical Report CENPD-138, Supplement 2-P" (34)

Letter from Mr. A. E. Lundvall, Jr. (BG&E) to Mr. J. R. Miller (NRC) dated February 22, 1985, "Calvert Cliffs Nuclear Power Plant Unit 1; Docket No. 50-317, Amendment to Operating License DPR-53, Eighth Cycle License Application" (Section 7.3.2 contains Methodology for Specifications 3.1.1 and 3.1.3 and 3.1.6)

(35)

Letter from Mr. D. H. Jaffe (NRC) to Mr. A. E. Lundvall, Jr. (BG&E), dated May 20, 1985, "Safety Evaluation Report Approving Unit 1 Cycle 8 License Application" (36)

Letter from Mr. A. E. Lundvall, Jr. (BG&E) to Mr. R. A. Clark (NRC), dated September 22, 1980, "Amendment to Operating License No. 50-317, Fifth Cycle License Application" (Section 7.1.2 contains Methodology for Specifications 3.1.1, 3.9.1)

(37)

Letter from Mr. R. A. Clark (NRC) to Mr. A. E. Lundvall, Jr. (BG&E), dated December 12, 1980, "Safety Evaluation Report Approving Unit 1, Cycle 5 License Application" (38)

Letter from Mr. J. A. Tiernan (BG&E) to Mr. A. C. Thadani (NRC), dated October 1, 1986, "Calvert Cliffs Nuclear Power Plant Unit Nos. 1 & 2, Docket Nos. 50-317 &

50-318, Request for Amendment" (Methodology for Specifications 3.1.4)

(39)

. Letter from S. A. McNeil, Jr. (NRC) to Mr. J. A. Tiernan (BG&E), dated July 7, 1987, Docket Nos. 50-317 and 50-318, Approval of Amendments 127 (Unit 1) and 109 (Unit 2)

(Support for Specification 3.1.4)

(40)

CENPD-188-A, "HERMITE: A Multi-Dimensional Space-Time Kinetics Code for PWR Transients," July 1976 (Methodology for Specifications 3.3.1, 3.1.6, 3.2.1, 3.2.2, 3.2.3, 3.2.5)

Calvert Cliffs 1. Cycle 18 COLR Page 23 of 25 Rev.3 I

Calvert Cliffs 1. Cvcle 18 COLR Paize 23 of 25 Rev. 3 1

(41)

The power distribution monitoring system referenced in various specifications and the BASES, is described in the following documents:

i-.

CENPD-153-P, Revision 1-P-A, "Evaluation of Uncertainty in the Nuclear Power Peaking Measured by the Self-Powered, Fixed Incore Detector System," May 1980 (Methodology for Specifications 3.3.1, 3.1.6, 3.2.1, 3.2.2, 3.2.3, 3.2.5) ii.

CEN-1 19(B)-P, "BASSS, Use of the Incore Detector System to Monitor the DNB-LCO on Calvert Cliffs Unit 1 and Unit 2," November 1979 (Referenced in Appendix B of Unit 2 Cycle 9 License Application) iii.

Letter from Mr. G. C. Creel (BG&E) to NRC Document Control Desk, dated February 7, 1989, "Calvert Cliffs Nuclear Power Plant Unit No. 2; Docket No. 50-318, Request for Amendment, Unit 2 Ninth Cycle License Application" (Appendix B contains Methodologies for Specifications 3.1.4, 3.2.2, 3.2.3, 3.2.5) iv.

Letter from Mr. S. A. McNeil, Jr. (NRC) to Mr. G. C. Creel (BG&E), dated January 10, 1990, "Safety Evaluation Report Approving Unit 2 Cycle 9 License Application" (42)

Letter from Mr. D. G. McDonald, Jr. (NRC) to Mr. R. E. Denton (BGE), dated May 11, 1995, "Approval to Use Convolution Technique in Main Steam Line Break Analysis -

Calvert Cliffs Nuclear Power Plant, Unit Nos. 1 and 2 (TAC Nos. M90897 and M90898)"

(Methodology for Specification 3.2.3).

(43)

CENPD-387-P-A, Latest Approved Revision, "ABB Critical Heat Flux Correlations for PWR Fuel" (44)

CENPD-199-P, Supplement 2-P-A, Appendix A, Latest Approved Revision, "CE Setpoint Methodology," June 1998.

(45)

CENPD-404-P-A, Latest Approved Revision, "Implementation of ZIRLOTM Cladding Material in CE Nuclear Power Fuel Assembly Designs".

(46)

CENPD-132, Supplement 4-P-A, Latest Approved Revision, "Calculative Methods for the CE Nuclear Power Large Break LOCA Evaluation Model".

(47)

CENPD-137, Supplement 2-P-A, Latest Approved Revision, "Calculative Methods for the ABB CE Small Break LOCA Evaluation Model".

.(48)

WCAP-1 1596-P-A, "Qualification of the PHOENIX-P, ANC Nuclear Design System for Pressurized Water Reactor Cores," June 1988.

(49)

WCAP-10965-P-A, "ANC: A Westinghouse Advanced Nodal Computer Code,"

September 1986.

(50)

WCAP-10965-P-A Addendum 1, "ANC: A Westinghouse Advanced Nodal Computer Code; Enhancements to ANC Rod Power Recovery," April 1989.

Calvert Cliffs 1 Cycle 18 COLR Paize 24 of 25 Rev. 31

(51)

WCAP-16045-P-A, "Qualification of the Two-Dimensional Transport Code PARAGON," August 2004.

(52)

WCAP-1 6072-P-A, "Implementation of Zirconium Diboride Burnable Absorber Coatings in CE Nuclear Power Fuel Assembly Designs," August 2004.

(?Mlve-rt Cfiff'q 1 (?vcle 1 R (M1IR~y~9 n2 PNap ?ý nf?.5 RP-.1 I I

ATTACHMENT (2)

CORE OPERATING LIMITS REPORT FOR UNIT 2, CYCLE 16, REVISION 1 Calvert Cliffs Nuclear Power Plant, Inc.

October 24, 2006

CALVERT CLIFFS NUCLEAR POWER PLANT CORE OPERATING LIMITS REPORT for UNIT 2, CYCLE 16 REVISION 1 RESPONSIBLE ENGINEER / DATE S PLENDENT REVIIEWER /DATE*

04 /0DA PRINIMIAL ENý EER - FOSU / DATE

.Calvert Cliffs 2, Cycle 16 COLR Page I of 25 Rev. I I

CORE OPERATING LIMITS REPORT CALVERT CLIFFS UNIT 2, CYCLE 16 The following limits are included in this Core Operating Limits Report:

Specification Title Page 3.1.1 3.1.3 3.1.4 3.1.6 3.2.1 3.2.2 3.2.3 3.2.5 3.3.1 3.9.1 Introduction..................................................................................................

.... 4 Definitions..........................................................................................................

5 Shutdown Margin (SDM).......................................................................................

6 Moderator Temperature Coefficient (MTC)...........................

6 Control Element Assembly (CEA) Alignment......................................................

6 Regulating Control Element Assembly (CEA) Insertion Limits...........................

6 Linear Heat Rate (LHR).........................................................................................

6 Total Planar Radial Peaking Factor (FxyT)..............................................................

7 Total Integrated Radial Peaking Factor (FT)........................................................

7 Axial Shape Index (ASI).....................................................................................

. 7 Reactor Protective System (RPS) Instrumentation - Operating.............................

7 Boron Concentration...........................................................................................

8 List of Approved Methodologies.........................................................................

21 The following figures are included in this Core Operating Limits Report:

Number Title Page Figure 3. 1.1 Figure 3.1.4 Figure 3.1.6 Figure 3.2.1-1 Figure 3.2.1-2 Figure 3.2.1-3 Figure 3.2.2" Figure 3.2.3 Figure 3.2.5 Figure 3.3.1-1 Figure 3.3.1-2 Figure 3.3.1-3 Shutdown M argin vs. Tim e in Cycle....................................................................

9 Allowable Time To Realign CEA Versus T

Initial Total Integrated Radial Peaking Factor (Fr)..........................

)..................

10 CEA Group Insertion Limits vs. Fraction of Rated Thermal Power......................... 11 Allowable Peak Linear Heat Rate vs. Time in Cycle.....................

12 Linear Heat Rate Axial Flux Offset Control Limits.............................................

13 T

Total Planar Radial Peaking Factor (Fy ) vs.

Scaling Factor (N -Factor)...................................................................................

14 T

Total Planar Radial Peaking Factor (Fxy ) vs. Allowable Fraction of Rated T herm al Pow er....................................................................................................

15 Total Integrated Radial Peaking Factor (F,) vs.

Allowable Fraction of Rated Thermal Power......................................................

16 DNB Axial Flux Offset Control Limits...............................................................

17 Axial Power Distribution - High Trip Setpoint Peripheral Axial Shape Index vs. Fraction of Rated Thermal Power.................. 18 Thermal Margin/Low Pressure Trip Setpoint - Part 1..........................................

19 Thermal Margin/Low Pressure Trip Setpoint - Part 2........................................

20 Calvert Cliffs 2, Cycle 16 COLR Page 2 of 25 Rev.l Calvert Cliffs 2, Cycle 16 COLR Page 2 of 25 Rev. I

UNIT 2 CORE OPERATING LIMITS REPORT LIST OF EFFECTIVE PAGES Page No.

Rev. No.

1 1*

2 1

3 1

4 1

5 1

6 1

7 1

8 1

9 1

10 1

11 1 _

12 1

13 1

14 1

15 1

16 1

17 1

18 1

19 1

20 1

21 1

22 1

23 1

24 1

25 1

Calvert Cliffs 2, Cycle 16 COLR Page 3 of 25 Rev. I I

INTRODUCTION This report provides the cycle-specific limits for operation of Calvert Cliffsý Unit 2, Cycle 16. It contains the limits for:

Shutdown Margin (SDM)

Moderator Temperature Coefficient (MTC)

Control Element Assembly (CEA) Alignment Regulating Control Element Assembly (CEA) Insertion Limits Linear Heat Rate (LHR)

Total Planar Radial Peaking Factor (FyT) T Total Integrated Radial Peaking Factor (Fr)

Axial Shape Index (ASI)

Reactor Protective System (RPS) Instrumentation - Operating Boron Concentration In addition, this report contains a number of figures which give limits on the parameters listed above. If any of the limits contained in this report are exceeded, corrective action will be taken as defined in the Technical Specifications.

This report has been prepared in accordance with the requirements of Technical Specifications.

The cycle specific limits have been developed using the NRC-approved methodologies given in the "List of Approved Methodologies" section of this report and in the Technical Specifications.

COLR Revision 0 Initial Release of Unit 2 Cycle 16 COLR (Safety Evaluation SE00495).

COLR Revision 1 Revised Figure 3.2.1-3 (N-Factor) as part of the corrective actions for IRE-017-571.

Calvert Cliffs 2, Cycle 16 COLR Page 4 of 25 Rev.1 II

DEFINITIONS Axial Shape Index (ASI)

ASI shall be the power generated in the lower half of the core less the power generated in the upper half of the core, divided by the sum of the power generated in the lower and upper halves of the core.

ASI = lower - upper

- YE lower + upper The Axial Shape Index (YI) used for the trip and pretrip signals in the Reactor Protection System (RPS) is the above value (YE) modified by an appropriate multiplier (A) and a constant (B) to determine the true core axial power distribution for that channel.

Y1 = AYE + B Total Integrated Radial Peaking Factor - FrT The Total Integrated Radial Peaking Factor is the ratio of the peak pin power to the average pin power in an unrodded core.

Total-Planar Radial Peaking Factor - FyT The Total Planar Radial Peaking Factor is the maximum ratio of the peak to average power density of the individual fuel rods in any of the unrodded horizontal planes.

Calvert Cliffs 2, Cycle 16 COLR Page 5 of 25 Rev. I I

CYCLE SPECIFIC LIMITS FOR UNIT 2, CYCLE 16 3.1.1 Shutdown Margin (SDM) (SR 3.1.1.1)

Tavg > 200 OF - Modes 3 and 4:

The shutdown margin shall be equal to or greater than the limit line of COLR Figure 3.1.1.

Tavg *<200 °F - Mode 5:

The shutdown margin shall be > 3.0% Ap.

3.1.3 Moderator Temperature Coefficient (MTC) (SR 3.1.3.2)

The Moderator Temperature Coefficient (MTC) shall be less negative than -3.0 x 10-4 Ap/°F at rated thermal power.

3.1.4 Control Element Assembly (CEA) Alignment (Action 3.1.4.B.1)

The allowable time to realign a CEA may be provided by the full core power distribution monitoring system (Better Axial Shape Selection System - BASSS) or COLR Figure 3.1.4, "Allowable Time to Realign CEA Versus Initial Total Integrated Radial Peaking Factor (F, )TY If COLR Figure 3.1.4 is used, the pre-misaligned Fr value used to determine the allowable time to realign the CEA shall be the latest measurement taken within 5 days prior to the CEA misalignment. If no measurements have been taken within 5 days prior to the misalignment and the full core power distribution monitoring system is unavailable then the time to realign is zero (0) minutes.

3.1.6 Regulating Control Element Assembly (CEA) Insertion Limits (SR 3.1.6.1 and SR 3.1.6.2)

The regulating CEA groups insertion limits are shown on COLR Figure 3.1.6.

3.2.1 Linear Heat Rate (LHR) (SR 3.2.1.2 and SR 3.2.1.4)

The linear heat rate shall not exceed the limits shown on COLR Figure 3.2.1-1.

.The axial shape index power dependent control limits are given in COLR Figure 3.2.1-2.

When using the excore detector monitoring system (SR 3.2.1.2):

The alarm setpoints are equal to the ASI. limits; therefore when the alarms are adjusted, they provide indication to the operator that ASI is not within the limits.

The axial shape index alarm setpoints are shown as a function of fraction of thermal power on COLR Figure 3.2.1-2. A scaling factor (N-Factor) vs. F"yT is shown in COLR Figure 3.2.1-3. The fraction of thermal power shown in COLR Figure 3.2.1-2 must be scaled by the N-Factor to determine the axial shape index alarm setpoints as a function of fraction of rated thermal power.

Calvert Cliffs 2, Cycle 16 COLR Page 6 of 25 Rev. I1

CYCLE SPECIFIC LIMITS FOR UNIT 2, CYCLE 16 When using the incore detector monitoring system (SR 3.2.1.4):

The alarm setpoints are adjusted to protect the Linear Heat Rate limits shown on COLR Figure 3.2.1-1 and uncertainty factors are appropriately included in the setting of these alarms.

The uncertainty factors for the incore detector monitoring system are:

1.

A measurement-calculational uncertainty factor of 1.062,

2.

An engineering uncertainty factor of 1.03,

3.

A linear heat rate uncertainty factor of 1.002 due to axial fuel densification and thermal expansion, and 4.a For measured thermal power less than or equal to 50 percent but greater than 20 percent of rated full core power a thermal power measurement uncertainty, factor of 1.03 5.

4.b For measured thermal power greater than 50 percent of rated full core power a thermal power measurement uncertainty factor of 1.020.

3.2.2 Total Planar Radial Peaking Factor (F'yT) (SR 3.2.1.1 and SR 3.2.2.1)

The calculated value of FxyT shall be limited to < 1.70.

The allowable combination of thermal power, CEA position, and FyT are shown on COLR Figure 3.2.2.

3.2.3 Total Integrated Radial Peaking Factor (Fr T) (SR 3.2.3.1)

The calculated value of FrT shall be limited to < 1.65.

The allowable combinations of thermal power, CEA position, and FrT are shown on COLR Figure 3.2.3.

3.2.5 Axial Shape Index (ASI) (SR 3.2.5.1)

The axial shape index and thermal power shall be maintained within the limits established by the Better Axial Shape Selection System (BASSS) for CEA insertions of the lead bank of

< 55% when BASSS is operable, or within the limits of COLR Figure 3.2.5 for CEA insertions specified by COLR Figure 3.1.6.

3.3.1 Reactor Protective System (RPS) Instrumentation - Operating (Reactor Trip Setpoints) (TS Table 3.3.1-1)

The Axial Power Distribution - High trip setpoint and allowable values are given in COLR Figure 3.3.1-1.

The Thermal Margin/Low Pressure (TMILP) trip setpoint is given in COLR Figures 3.3.1-2 and 3.3.1-3. The allowable values are to be not less than the larger of(1) 1875 psia or (2) the value calculated from COLR Figures.3.3.1-2 and 3.3.1-3.

Calvert Cliffs 2, Cycle 16 COLR Page 7 of 25 Rev.1 Calvert Cliffs 2, Cycle 16 COLR Page 7 of 25 Rev. I I

3.9.1 Boron Concentration (SR 3.9.1.1)

The refueling boron concentration will maintain the keff at 0.95 or less (including a 1% Ak/k conservative allowance for uncertainties). The refueling boron concentration shall be maintained uniform. For Mode 6 operation the RCS temperature must be maintained

< 140 OF. The '.'0 Credited CEAs" requirement shall apply for a Post-Refueling Upper Guide Structure or Reactor Vessel Head Lift of more than 12 inches.

Refueling Boron Concentration Limits Post-Refueling UGS or RV Head lift height restrictions. (Note 2)

<12 inches No restriction No restriction COLR/Tech Spec Limit 2255 ppm 2486 ppm 2486 ppm.

Chemistry Sampling 23 ppm 25 ppm 25 ppm Boron-10 Depletion 47 ppm 51 ppm 51 ppm Refueling Boron Concentration

> 2325 ppm

> 2562 ppm

> 2562 ppm Limit including Chemistry Sampling uncertainty and Boron-10 Depletion Dilution of the Refueling Pool between Low and 73 ppm 80 ppm 80 ppm High Level Alarms with Refueling Pool Flooded Any number of Temporary An allowance of 20 An allowance of 20 Rotations of Fuel ppm is already included ppm is already included Rotations of Fuel Assemblies in the above in the above COLR/Tech Spec Limit COLR/Tech Spec Limit An allowance of 50 An allowance of 50 U2C16 In-Core Shuffle.

ppm is already included ppm is already included Allowance in the above in the above AncoreS COLR/Tech Spec Limit COLR/Tech Spec Limit Allowed Refueling Boron Concentration Administrative Limit

? 2398 pprn

> 2642 ppm

> 2642 ppm (Note

_)

Note:

(1) The above table specifies the minimum technical requirements.

conservatively list higher ppm values.

(2)

Fuel and CEAs must be in their final U2C16 configurdtion.

It is acceptable forNEOP-23 to Calvert Cliffs 2, Cycle 16 COLR Page 8 of 25 Rev. I I

6 5-I i a I

z z

o 2-0-

I-

"I" 0)

ACCEPTABLE OPERATION (EOC, 4.5)

REGION (BOC, 3.5)

MINIMUM SHUTDOWN MARGIN UNACCEPTABLE OPERATION REGION I

BOC EOC TIME IN CYCLE Figure 3.1.1 Shutdown Margin vs. Time in Cycle Calvert Cliffs 2, Cycle 16 COLR Page 9 of 25 Rev.1 Calvert Cliffs 2, Cycle 16 COLR Page 9 of 25 Rev. I1

70 60 (1.53,60) 50 D

I-z 40 S978-600Frt z

3 0

_J w

O 20 w

10 ALLOWED REGION 0

(1.63, 0)

I I

I I

I I

I I

I I

I I

I I

I

• I I

1.50 1.55 1.60 1.65 1.70 MEASURED PRE-MISALIGNED TOTAL INTEGRATED RADIAL PEAKING.

FACTOR Figure 3.1.4 Allowable Time to Realign CEA Versus Initial Total Integrated Radial Peaking Factor (FrT)

Calvert Cliffs 2, Cycle 16 COLR Page 10 of 25 Rev. I I

(1.00 FRTP, Group 5 @ 35% Inserted) 0.900 -~

-t-

~

H 0.800 U N U.

(0.475 FRT Group 5 @ 50% nsertedy t

OERA ING W

1(0.70 FRTP, Grdup 5 @60/ Inserted) z OPERATING

-=..

R.

I..--

4o a -'

(0.651FRTP, roup 5 @85% Inerted) i

... RF I

-j 9

-'I--

I t

t%

0 0

oGroup 50%

To.. 6 FR15 0.5 0 0.....

IU.

I 0.400 j

0.5 0 0 o......o M

0.100

-I-__

0.200 Ao 4

(A0bove2ero Po ter P001 SetpointI Group 31@ 60%

eserted)

Setpoint I-0%

20%

40%

60%

80%

100%

0%

20%

400/

60%

80%

100%

0%

20%

40/%

60/%

80%

100%

135' 108' 81 54 27" 0"

135

108, 81" 54" 27" 0"

135" 108" 81 54 27 0

0 '

• 0+

I RL AI "

4 RE U AIN I

2 0%

20%

40%

60%

80%

100%

0%

20%

40%

60%

80%

100%

135" 108" 81" 54" 2T' 0"

135" 108" 81" 54" 27" 0"

%CEA INSERTION INCHES CEA WITHDRAWN (ARO is defined in NEOP-23)

Figure 3.1.6 CEA Group Insertion Limits vs. Fraction of Rated Thermal Power Calvert Cliffs 2, Cycle 16 COLR Page I I of 25 Rev. I I

17.0 16.5 I.-

U-a.i I-0 I-ILl

_z 0.u

..J 03 0

_,1 16.0 0

1-155 a

0

+

15.0 1-J

,.-)

w 14.5

,. 14.3 UNACCEPTABLE OPERAT1ON ACCEPTABLE OPERATION 14.0 13.5 13.0 BOC EOC TIME IN CYCLE Figure 3.2.1-1 Allowable Peak Linear Heat Rate vs. Time in Cycle Calvert Cliffs 2, Cycle 16 COLR Page 12 of 25 Rev.1 Calvert Cliffs 2, Cycle 16 COLR Page 12 of 25 Rev. I I

W 0~

-JJ I.

I-U-

0z 0

P 0*1 LLI 1.100-1.050 1.000

(-0.08,1.00)0.12,1.00) 0.950 UNACCEPTABLEUNACCEPTABLE UNACCEPTABL 0.900-OPERATION OPERATION REGION REGION 0.850*

G 0.800 0.750 0.700

(-0.3,*0.70)

ACCEPTABLE (0.3, 0.70)

OPERATION 0.650 REGION 0.600 0.550 0.500

(-0.3, 0.50) 0.450 0.400 0.350 0.300 0.250

(-0.42, 0.20)

(0.3, 0.20) 0.200 tI III I

-0.60

-0.40

-0.20 0.00 0.20 0.40 PERIPHERAL AXIAL SHAPE INDEX, Y Figure 3.2.1-2 Linear Heat Rate Axial Flux Offset Control Limits (LCO Limits are not needed below 20% thermal power per SE00433)

(See NEOP-23 for Administrative Limits) 0.60 Calvert Cliffs 2, Cycle 16 COLR Page 13 of 25 Rev. 1

.1

1.00 0.90--

0.80-I-"

0 M-

• ,0.70-0 o 0.60 U-CD ACCEPTABLE VALUE zS0.50-0.40--

0.30-0.20 1.35 1.40 1.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 Fxy T Figure 3.2.1-3 Total Planar Radial Peaking Factor (FxyT) vs.

Scaling Factor (N-Factor)

(See NEOP-23 for Administrative Limits)

Calvert Cliffs 2, Cycle 16 COLR Page 14 of25 Rev.1 Calvert Cliffs 2, Cycle 16 COLR Page 14 of 25 Rev. I I

1.05 W05-UItI-(M I IUN 0.95 (1.70, 1.00)

REGION CL 0.85 M

(1.7850, 0.8)

W, 0.75-F-rT LIMIT CURVE

- 0.65 IL 0.55 0z0 i

0.45-0.3 ACCEPTABLE OPERATION REGION S0.25-0 (1.874, 0.20) 0.15 0.05I 1.60 1.65 1.70 1.75 1.80 1.85 1.90 T

Fxy Figure 3.2.2 Total Planar Radial Peaking Factor (FxyT) VS.

Allowable Fraction of Rated Thermal Power T

While operating with Fxy greater than 1.70, withdraw CEAs to or above the Long Term Steady State Insertion Limits (Figure 3.1.6)

Calvert Cliffs 2, Cycle 16 COLR Page 15 of25 Rev.1 Calvert Cliffs 2, Cycle 16 COLR Page 15 of 25 Rev. I I

1.05 UNACI-PI ABLIE W 0.95--

OPERATION 0

REGION 0.85 (10.7325, 0.80)

UJ0.65-u, 0.55 0z 0.45 ACCEPTABLE o

OPERATION Ug0.35-REGION

-j

< 0.25 O..j:0.1 (1.819,0.20)l 0.1 0.05 1.60 1.65 1.70 1.75 1.80 1.85 T

Fr Figure 3.2.3 Total Integrated Radial Peaking Factor (FrT) VS.

Allowable Fraction of Rated Thermal Power While operating with FrT greater than 1.65, withdraw CEAs to or above the Long Term Steady State Insertion Limits (Figure 3.1.6)

Calvert Cliffs 2, Cycle 16 COLR Page 16 of 25 Rev. I I

-JW W

-J w

0 ILJ 0~

.. i

-J D

0-J

-J u.

U-0 z.

1.100-1.050 1.000 0.950 t

0.900 0.850

.0.800 0.750 0.700 0.650 0.600 0.550 0.500 0.450 0A400 0.350 0.300 0.250 0.2004-

-0.60

-0.40

-0.20 0.00 0.20 0.40 PERIPHERAL AXIAL SHAPE INDEX, Yi 0.60 Figure 3.2.5 DNB Axial Flux Offset Control Limits (LCO Limits are not needed below 20% thermal power per SE00433)

(See NEOP-23 for Administrative Limits)

Calvert Cliffs 2, Cycle 16 COLR Page 17 of 25 Rev.1 Calvert Cliffs 2, Cycle 16 COLR Page 17 of 25 Rev. I1

W 0~

(L I-9 LL 0z 0

0.

1.300 1.250 1.200 1.150 1.100 1.050 1.000 0.950 0.900 0.850 0.800 0.750 0.700 0.650 0.600 0.550 0.500 0.450 0.400 0.350 0.300 0.250 0.200 0.150

-0.80

-0.60

-0.40

-0.20 0.00 0.20 0.40 PERIPHERAL AXIAL SHAPE INDEX, Yi 0.60 0.80 Figure 3.3.1-1 Axial Power Distribution - High Trip Setpoint Peripheral Axial Shape Index vs. Fraction of Rated Thermal Power Calvert Cliffs 2, Cycle 16 COLR Page 18 of 25 Rev. I

1.60 1.50 -

QDNB A1 x QR1 1.40 1.30

(-0.6, 1.3) 1.20 A

17 x AI + 1.

1..10._

Al

-0.5 x 1I+10 1.00__

(0.0, 1 0) 0.90

-0.60 -0.50 -0.40 -0.30 -0.20 -0.10 0.00 0.10 0.20 0.30 0.40 ASI Figure 3.3.1-2 Thermal Margin/Low Pressure Trip Setpoint - Part I (ASI vs. A1) 0.50 0.60 Calvert Cliffs 2, Cycle 16 COLR Page 19 of25 Rev.1 Calvert Cliffs 2, Cycle 16 COLR Page 19 of 25 Rev. I I

pTrip-2895x(

Pvar 2869.5 x (A1) x (QR1) + 17.98 x Ti, - 10820 QDNB

=Al x QR1 1.2 1.1 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 (1.2, 1.2) 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 FRACTION OF RATED THERMAL POWER (RTP)

Figure 3.3.1-3 Thermal Margin/Low Pressure Trip Setpoint - Part 2 (Fraction of Rated Thermal Power vs. QR1 )

Calvert Cliffs 2, Cycle 16 COLR Page 20 of 25 Rev. I I

LIST OF APPROVED METHODOLOGIES (1)

CENPD-199-P, Rev 1-P-A, "C-E Setpoint Methodology: C-E Local Power Density and DNB LSSS and LCO Setpoint Methodology for Analog Protection Systems," January 1986.

Additionally, Supplement 2-P-A dated June 1998. (Methodology for Specifications 3.3.1, 3.1.6, 3.2.1, 3.2.2, 3.2.3, 3.2.5)

(2)

CEN-124(B)-P, "Statistical Combination of Uncertainties Methodology Part 1: C-E Calculated Local Power Density and Thermal Margin/Low Pressure LSSS for Calvert Cliffs Units I and II,"

December 1979 (Methodology for Specifications 3.3.1, 3.1.6, 3.2.2, 3.2.3)

(3)

CEN-124(B)-P, "Statistical Combination of Uncertainties Methodology Part 2: Combination of System Parameter Uncertainties in Thermal Margin Analyses for Calvert Cliffs Units 1 and 2,"

January 1980 (Methodology for Specifications 3.3.1, 3.1.6, 3.2.3, 3.2.5)

(4)

CEN-124(B)-P, "Statistical Combination of Uncertainties Methodology Part 3: C-E Calculated Departure from Nucleate Boiling and Linear Heat Rate Limiting Conditions for Operation for Calvert Cliffs Units 1 and 2," March 1980 (Methodology for Specifications 3.1.6, 3.2.1, 3.2.2, 3.2.3, 3.2.5)

(5)

CEN-191(B)-P. "CETOP-D Code Structure and Modeling Methods for Calvert Cliffs Units 1 and 2," December 1981 (Methodology for Specifications 3.3.1, 3.1.6, 3.2.3, 3.2.5)

(6)

Letter from Mr. D. H. Jaffe (NRC) to Mr. A. E. Lundvall, Jr. (BG&E), dated June 24, 1982, Unit 1 Cycle 6 License Approval (Amendment No. 71 to DPR-53.and SER) [Approval to CEN-124(B)-P (three parts) and CEN-191(B)-P)]

(7)

CEN-348(B)-P, "Extended Statistical Combination of Uncertainties," January 1987 (Methodology for Specifications 3.3.1, 3.1.6, 3.2.3, 3.2.5)

(8)

Letter from Mr. S. A. McNeil, Jr. (NRC) to Mr. J. A. Tiernan (BG&E), dated October 21, 1987, Docket Nos. 50-317 and 50-318, "Safety Evaluation of Topical Report CEN-348(B)-P, Extended Statistical Combination of Uncertainties" (9)

CENPD-161-P-A, "TORC Code, A Computer Code for Determining the Thermal Margin of a Reactor Core," April 1986 (Methodology for Specifications 3.3.1, 3.1.6, 3.2.3, 3.2.5)

(10)

CENPD-162-P-A, "Critical Heat Flux Correlation of C-E Fuel Assemblies with Standard Spacer Grids Part 1, Uniform Axial Power Distribution," April 1975 (Methodology for Specifications 3.3.1, 3.1.6, 3.2.3, 3.2.5)

(11)

CENPD-207-P-A, "Critical Heat Flux Correlation for C-E Fuel Assemblies with Standard Spacer Grids Part 2, Non-Uniform Axial Power Distribution," December 1984 (Methodology for Specifications 3.3.1, 3.1.6, 3.2.3, 3.2.5)

(12)

CENPD-206-P-A, "TORC Code, Verification and Simplified Modeling Methods," June 1981 (Methodology for Specifications 3.3.1, 3.1.6, 3.2.3, 3.2.5)

(13)

CENPD-225-P-A, "Fuel and Poison Rod Bowing," June 1983 (Methodology for Specifications 3.3.1, 3.1.6, 3.2.3, 3.2.5)

Calvert Cliffs 2, Cycle 16 COLR Page 21 of 25 Rev. I I

(14)

CENPD-266-P-A, "The ROCS and DIT Computer Code for Nuclear Design," April 1983 (Methodology for Specifications 3.3.1, 3.1.6, 3.2.1, 3.2.2, 3.2.3, 3.2.5)

(15)

CENPD-275-P-A, "C-E Methodology for Core Designs Containing Gadolinia - Urania Burnable Absorbers," May 1988 (Methodology for Specifications 3.3.1, 3.1.6, 3.2.1, 3.2.2, 3.2.3, 3.2.5)

(16)

CENPD-3 82-P-A, "Methodology for Core Designs Containing Erbium Burnable Absorbers," August 1993 (Methodology for Specifications 3.3.1, 3.1.6, 3.2.1, 3.2.2, 3.2.3, 3.2.5)

(17)

CENPD-139-P-A, "C-E Fuel Evaluation Model Topical Report," July 1974 (Methodology for Specifications 3.3.1, 3.1.6, 3.2.1, 3.2.2)

(18)

CEN-161-(B)-P-A, "Improvements to Fuel Evaluation Model," August 1989 (Methodology for Specifications 3.3.1, 3.1.6, 3.2.1, 3.2.2)

(19)

CEN-161-(B)-P, Supplement l-P, "Improvements to Fuel Evaluation Model," April 1986 (Methodology for Specifications 3.3.1, 3.1.6, 3.2.1, 3.2.2)

(20)

Letter from Mr. S. A. McNeil, Jr. (NRC) to Mr. J. A. Tiernan (BG&E), dated February 4, 1987, Docket Nos. 50-317 and 50-318, "Safety Evaluation of Topical Report CEN-161-(B)-P, Supplement 1 -P, Improvements to Fuel Evaluation Model" (Approval of CEN-161(B), Supplement 1-P)

(21)

CEN-372-P-A, "Fuel Rod Maximum Allowable Gas Pressure," May 1990 (Methodology for Specifications 3.3.1, 3.1.6, 3.2.1, 3.2.2)

(22)

Letter from Mr. A. E. Scherer (CE) to Mr. J. R. Miller (NRC) dated December 15, 1981, LD-81-095, Enclosure l-P, "C-E ECCS Evaluation Model Flow Blockage Analysis" (Methodology for Specifications 3.2.1, 3.2.2)

(23)

CENPD-132, Supplement 3-P-A, "Calculative Methods for the C-E Large Break LOCA Evaluation Model for the Analysis of C-E and W Designed NSSS," June 1985 (Methodology for Specifications 3.2.1, 3.2.2 and approval of Letter LD-81-095, dated December 15, 1981)

(24)

CENPD-133, Supplement 5, "CEFLASH-4A, a FORTRAN77 Digital Computer Program for Reactor Blowdown Analysis," June 1985 (Methodology for Specifications 3.2.1, 3.2.2)

(25)

CENPD-134, Supplement 2, "COMPERC-II, a Program for Emergency Refill-Reflood of the Core," June 1985 (Methodology for Specifications 3.2.1, 3.2.2)

(26)

Letter from Mr. D. M. Crutchfield (NRC) to Mr. A. E. Scherer (CE), dated July 31, 1986, "Safety Evaluation of Combustion Engineering ECCS Large Break Evaluation Model and Acceptance for Referencing of Related Licensing Topical Reports (Approval of CENPD-133, Supplement 5 and CENPD-134, Supplement 2)

(27)

CENPD-135, Supplement 5-P, "STRIKIN-II, A Cylindrical Geometry Fuel Rod Heat Transfer Program," April 1977 (Methodology for Specifications 3.2.1, 3.2.2)

Calvert Cliffs 2, Cycl 16 COLR Page 22 of 25 Rev. I I

(28)

Letter from Mr. R. L. Baer (NRC) to Mr. A. E. Scherer (CE) dated September 6, 1978, "Evaluation of Topical Report CENPD-135, Supplement 5" (29)

CENPD-137, Supplement l-P, "Calculative Methods for the C-E Small Break LOCA Evaluation Model," January 1977 (Methodology for Specifications 3.2.1, 3.2.2)

(30)

CENPD-133, Supplement 3-P, "CEFLASH-4AS, "A Computer Program for the Reactor Blowdown Analysis of the Small Break Loss of Coolant Accident," January 1977 (Methodology for Specifications 3.2.1, 3.2.2)

.(31)

Letter from Mr. K. Kniel (NRC) to Mr. A. E. Scherer (CE), dated September 27, 1977, "Evaluation of Topical Reports CENPD-133, Supplement 3-P and CENPD-137, Supplement 1-P" (32)

CENPD-138, Supplement 2-P, "PARCH, A FORTRAN-IV Digital Program to Evaluate Pool Boiling, Axial Rod and Coolant Heatup," January 1977 (Methodology for Specifications 3.2.1, 3.2.2)

(33)

Letter from Mr. C. Aniel (NRC) to Mr. A. E. Scherer, dated April 10, 1978. "Evaluation of Topical Report CENPD-138, Supplement 2-P" (34)

Letter from Mr. A. E. Lundvall, Jr. (BG&E) to Mr. J. R. Miller (NRC) dated February 22, 1985, "Calvert Cliffs Nuclear Power Plant Unit 1; Docket No. 50-317, Amendment to Operating License DPR-53, Eighth Cycle License Application" (Section 7.3.2 contains Methodology for Specifications 3.1.1 and 3.1.3 and 3.1.6)

(35)

Letter from Mr. D. H. Jaffe (NRC) to Mr. A. E. Lundvall, Jr. (BG&E), dated May 20, 1985, "Safety Evaluation Report Approving Unit 1 Cycle 8 License Application" (36)

Letter from Mr. A. E. Lundvall, Jr. (BG&E) to Mr. R. A. Clark (NRC), dated September 22, 1980, "Amendment to Operating License No. 50-317, Fifth Cycle License Application" (Section 7.1.2 contains Methodology for Specifications 3.1.1, 3.9.1)

(37)

Letter from Mr. R. A. Clark (NRC) to Mr. A. E. Lundvall, Jr. (BG&E), dated December 12, 1980, "Safety Evaluation Report Approving Unit 1, Cycle 5 License Application" (38)

Letter from Mr. J. A. Tiernan (BG&E) to Mr. A. C. Thadani (NRC), dated October 1, 1986, "Calvert Cliffs Nuclear Power Plant Unit Nos. 1 & 2, Docket Nos. 50-317 &

50-318, Request for Amendment" (Methodology for Specifications 3.1.4)

(39)

Letter from S. A. McNeil, Jr. (NRC) to Mr. J. A. Tiernan (BG&E), dated July 7, 1987, Docket Nos. 50-317 and 50-318, Approval of Amendments 127 (Unit 1) and 109 (Unit 2)

(Support for Specification 3.1.4)

(40)

CENPD-188-A, "HERMITE: A Multi-Dimensional Space-Time Kinetics Code for PWR Transients," July 1976 (Methodology for Specifications 3.3.1, 3.1.6, 3.2.1, 3.2.2, 3.2.3, 3.2.5)

Calvert Cliffs 2, Cycle 16 COLR Page 23 of 25 Rev.1 Calvert Cliffs 2, Cycle 16 COLR Page 23 of 25 Rev. I I

(41)

The power distribution monitoring system referenced in various specifications and the BASES, is described in the following documents:

CENPD-153-P, Revision 1-P-A, "Evaluation of Uncertainty in the Nuclear Power Peaking Measured by the Self-Powered, Fixed Incore Detector System," May 1980 (Methodology for Specifications 3.3.1, 3.1.6, 3.2.1, 3.2.2, 3.2.3, 3.2.5) ii.

CEN-1 19(B)-P, "BASSS, Use of the Incore Detector System to Monitor the DNB-LCO on Calvert Cliffs Unit 1 and Unit 2," November 1979 (Referenced in Appendix B of Unit 2 Cycle 9 License Application) iii.

Letter from Mr. G. C. Creel (BG&E) to NRC Document Control Desk, dated February 7, 1989, "Calvert Cliffs Nuclear Power Plant Unit No. 2; Docket No. 50-318, Request for Amendment, Unit 2 Ninth Cycle License Application".

(Appendix B contains Methodologies for Specifications 3.1.4, 3.2.2, 3.2.3, 3.2.5) iv.

Letter from Mr. S. A. McNeil, Jr. (NRC) to Mr. G. C. Creel (BG&E), dated January 10, 1990, "Safety Evaluation Report Approving Unit 2 Cycle 9 License Application" (42)

Letter from Mr. D. G. McDonald, Jr. (NRC) to Mr. R. E. Denton (BGE), dated May 11, 1995, "Approval to Use Convolution Technique in Main Steam Line Break Analysis -

Calvert Cliffs Nuclear Power Plant, Unit Nos. 1 and 2 (TAC Nos. M90897 and M90898)"

(Methodology for Specification 3.2.3).

(43)

CENPD-387-P-A, Latest Approved Revision, "ABB Critical Heat Flux Correlations for PWR Fuel" (44)

CENPD-199-P, Supplement 2-P-A, Appendix A, Latest Approved Revision, "CE Setpoint Methodology," June 1998.

(45)

CENPD-404-P-A, Latest Approved Revision, "Implementation of ZIRLOTM Cladding Material in CE Nuclear Power Fuel Assembly Designs".

(46)

CENPD-132, Supplement 4-P-A, Latest Approved Revision, "Calculative Methods for the CE Nuclear Power Large Break LOCA Evaluation Model".

(47)

CENPD-137, Supplement 2-P-A, Latest Approved Revision, "Calculative Methods for the ABB CE Small Break LOCA Evaluation Model".

(48)

WCAP-1 1596-P-A, "Qualification of the PHOENIX-P, ANC Nuclear Design System for Pressurized Water Reactor Cores," June 1988.

(49)

WCAP-10965-P-A, "ANC: A Westinghouse Advanced Nodal Computer Code,"

September 1986.

(50)

WCAP-10965-P-A Addendum 1, "ANC: A Westinghouse Advanced Nodal Computer Code; Enhancements to ANC Rod Power Recovery," April 1989.

Calvert Cliffs 2, Cycle 16 COLR Page 24 of 25 Rev. I I

(51)

WCAP-16045-P-A, "Qualification of the Two-Dimensional Transport Code PARAGON," August 2004.

(52)

WCAP-16072-P-A, "Implementation of Zirconium Diboride Burnable Absorber Coatings in CE Nuclear Power Fuel Assembly Designs," August 2004.

Calvert Cliffs 2, Cycle 16 COLR Page 25 of 25 Rev. I I