ML20236J612
| ML20236J612 | |
| Person / Time | |
|---|---|
| Site: | 07104909 |
| Issue date: | 10/21/1987 |
| From: | Winslow T GENERAL ELECTRIC CO. |
| To: | Macdonald C NRC OFFICE OF NUCLEAR MATERIAL SAFETY & SAFEGUARDS (NMSS) |
| References | |
| 28713, NUDOCS 8711060190 | |
| Download: ML20236J612 (4) | |
Text
- _ _ - _
s.;'.
3W-SM 7/-@fdf) h
~
.GENERALh ELECTRIC:
j
^
NUCLEAR FUEL & COMPONENTS MANUFACTURING-
, ( GENERAL ELECTRC COMPANY
- P,0. BOX 780. WILMINGTON. NORTH CAROUNA'28402
-:[
'87 6EtIdeN5l,I 1987
~
e
~
+
6 S
RECElVEDLy 2
OCT2 71987. N
- Mr. Charles
- E. MacDonald, Chief
[hu,$.flugEA RgulATORY Q Transportation Branch' e
Nust
?
Division of Safeguards
&' Transportation kf M
J K:
..U.
S. Nuclear Regulatory Commission b, t g g,p.
v Washington, D. C. 20555
Dear Mr. MacDonald:
~ References (1) Certificate of Compliance USA /4909/AF (2) Letter, CE MacDonald to TP Winslow, 8/26/87 2
GE Wilmington hereby requests renewal of the subject certificate 0
l for. the' GE-21PF-1 package.
.j In response' to t your letter of August -26,.1987, attached is a description. of our operating procedures, quality control' acceptance tests,'and maintenance programs.for the GE-21PF-1.
Pursuant'to-10 CFR 170.30, a check for $150 will be ' forwarded under separate cover.
If you~hava any q'uestions regarding.this matter, please contact h
me.
Very truly yours, l
8711060190 071021 GE NUCLEAR ENERGY J
PDR ADOCK 0710 9
q w&
n er T.
Preston Winslow, Manager l
[iM/CJ88 Licensing & Nuclear Materials Management
/sbm e
Attachment
' p Et x
N'N SGD-L E5
- f' mum
%s'\\
yg:~pt=[f~
L
}
a gg
.[w 6-l-
syy J / n a p &.
OCT2 71987}k i,'d;,
't g33pv j
g I2 nm i
T Liu 70-itt3 %
"'u nno" ii
/d.h occm cum J
g 1]W
\\
'c to24f//
{
"'/ & N l
\\
j= v/t 7 d "'
hff/h
~
n 1
P
.A f
i
-(
pQc -
, ]~
.j G EN ER ALk ELECTRIC l
t
]
.Mr. Charles E.'MacDonald 7
E0ctober'21, 1987
-(-
s j]
ATTACHMENT G,E-21PF-1 UF6-SHIPPING ~ PACKAGING (CASK)'
.I.
OPERATING PROCEDURES q
LA.: Assure gasket is in place and in? good condition.
i B..
Bolt Assembly-
,j 1)
Assure bolts are placed through' bottom half of: cask,
,s
. threaded end up 2)
Slowly. lower zlid and assure holes are aligned
]
3)- With lid.in place, push bolts up through ' holes in cask lid and-install washers and nuts -
- 4) ' Apply tampersafe seals II. - QUALITY ' CONTROL-ACCEPTANCE TESTS
- A.-
A Receiving. Inspection. or Source Inspection is performed.
on each. purchased' cask to assure.each. unit conformsLto drawing dimensional-requirements.. Material certificationsrare evaluated to assure conformance to-specif1ca, tion' requirements.
J3. ' A ' visual inspection is performed for each cask.
containing a UF6 cylinder that enters or. leaves the l
f acility to assure the following:
1)
Cask base and support a)
Bolted tightly to trailer b)
No broken welds I
l l
o
' GENERAL $ ELECTRIC l
1 Mr.' Charles E.
MacDonald October 21, 1987 Attachment - Page 2 I
I
'i 2)
Cask body has no holes and no dents greater than 0.5 i
inch 3)
Inside cask liner is intact with no holes or deformation 4
4)
Pads j
a)
In place-b)
No' missing pad surface c)
Not torn or defaced j
l 5)
Gaskets l
a)
Intact, no missing segments b)
Not cracked or torn 6)
Mating cask halves a)
Proper fit b)
No gaps 7)
Fastner bolts and nuts are tight 8)
Joints between outer and inner shell are seal welded and are inspected for weld integrity III.
MAINTENANCE PROGRAM A.
UF6 casks that are rejected during inspection are repaired and reinspected.
B.
Repairs shall conform with ANSI N14.1-1982, or most current revision C.
Cask gaskets are replaced every 12 nonths per NRC certificate requirements and when damaged.
l..
' I 'I t 1
e i
I 4
k l~ Y b 00CHET No.
- CONTROL NO.
_ /8!
8I DATE OF D00.
I DATE RCVD.
-FCUF PDR FCAF LPDR
_/
,/
l & E flEF, _, V -
)
SAFEGUARD 3
- i FCTC __.
OTi!ER DATEM8Y INiilAL a
I
)
I f
l i
I E
l p.
,.