ML20205C744
| ML20205C744 | |
| Person / Time | |
|---|---|
| Site: | Hope Creek  |
| Issue date: | 09/18/1985 |
| From: | Mittl R Public Service Enterprise Group |
| To: | Butler W Office of Nuclear Reactor Regulation |
| Shared Package | |
| ML20205C750 | List: |
| References | |
| NUDOCS 8509230192 | |
| Download: ML20205C744 (3) | |
Text
..
O PS Puttc Servd Electnc and Gas Company 80 Park Plaza. Newark, NJ 07101/ 201430-8217 MAlLING ADDRESS / P.O. Box 570 Newark, NJ 07101 Robert L Mitti General Manager Nuclear Assurance and Regulation September 18, 1985 Director of Nuclear Reactor Regulation
-United States Nuclear Regulatory Commission 7920 Norfolk Avenue Bethesda, Maryland 20814 Attention:
Mr. Walter Butler, Chief Licensing Branch 2 Division of Licensing Gentlemen:
RESPONSE TO SQRT CONFIRMATORY ISSUE 5 HOPE CREEK GENERATING STATION DOCKET NO. 50-354 Pursuant to the NRC, PVORT/SQRT audit held at the Hope Creek Generating Station on May 7-10, 1985, Public Service Electric and Gas Company hereby submits the attached response to SQRT Confirmatory Issue 5-DSER Open Item.103/SER Open Item 2,
" Equipment' Qualification".
This response regards the extent to which draft standards ANSI /ASME QP-1 (N551.1),
QP-2 (N551.2),~QP-3 (N551.3), QP-4 (N551.4), and issued standards ANSI N41.6 and ANSI B16.41-1983 are used for Hope Creek pump and valve qualification / operability as requested in letter; A.
Schwencer (NRC) to R.L. Mittl (PSE&G), dated February 11, 1985.
This response is presented in check list form for a pump and motor and a valve which were reviewed for extent of compliance with the standards listed above.
This information will be included in Amendment 13 to the HCGS FSAR in fulfillment of the request in the letter cited above.
8509230192 850918
~
PDR ADOCM 05000354
{
E PDR i
' i,\\
l The Energy People 96 4'112 (3M) 4 R4
s Director of Nuclear 2
'9/18/85 Reactor Regulation This completes the resolution of the SQRT audit action items which were a result of the PVORT/SQRT audit.
Should you have any, questions in this regard, please contact us.
Very truly yours, 1J m
-s Attachment C
D.H. Wagner USNRC Licensing Project Manager A.R. Blough USNRC Senior Resident Inspector J.
Singh EGiG Idaho, Inc.
i I
e
ATTACHMENT DSER Open Item No. 103.
E xtent of Pump and Valve Qualification / Operability per Draf t Standards ANSI /ASME QP-1 (N551.1), QP-2 (N551.2), QP-3 (N551.3), QP-4 (N551.4),
and Issued ANSI Standards N41.6 and B16.41-1983 The subject standards are not included in the Acceptance Criteria of NRC Standard Review Plan (SRP ) 3.10.
However, these standa rds are identified in the review procedure.
The extent to which these draft standards are used in the qualification of pumps and valves is given below:
Valves:
ANSI Std. N 41.6 is the same as IEEE Std. 382-1972.
This standard is complied f ully in the qualification of all the valves.
The extent of qualification of one 18" Motor Operated Valve has been reviewed against the requirements of ANSI Std. B16.41-19 83.
The check list is given in Attachment A.
Essentially the require-ments of this standard are met in the qualification of 18 "Moto r Operated Valve.
Pumps and Motors:
The qualification of Safety Auxiliaries Cooling '
System Pump and Valve has been reviewed per the requirements of Draf t Standards QP-1, QP-2, QP-3, QP-4.
Some additional inf o rma-tion was obtained from the manuf acturer recently in this connec-tion.
Attachment B gives a check list for SACS Pump and Motor.
Essentially, the requirements of these standards are met, except for that of QP-3 (Shaf t Seal Assemblies).
F6/49 i J
e
.,.. -