ML19257A884
| ML19257A884 | |
| Person / Time | |
|---|---|
| Site: | Haddam Neck File:Connecticut Yankee Atomic Power Co icon.png |
| Issue date: | 01/03/1980 |
| From: | Randy Hall BROOKHAVEN NATIONAL LABORATORY |
| To: | Ferguson R Office of Nuclear Reactor Regulation |
| References | |
| NUDOCS 8001090345 | |
| Download: ML19257A884 (3) | |
Text
.
~
'73 i j BROOKHAVEN NATIONAL LABORATORY a
C'l' ASSOCIATED UNIVERSITIES, INC L.
~n 2 Upton. New York 11973 Department of Nuclear Energy (516) 345-2144 D
January 3,1980 Mr. Robert L. Ferguson Plant Systems Branch U.S. Nuclear Regulatory Commission Washington, D.C.
20555 RE: Haddam Neck Nuclear Power Plant Fire Protection Review Item 3.2.3
Dear Bob:
Attached is the completed Fire Protection Review Item 3.P. 3 - Fire Barrier Penetration Test Data.
Respectfully yours,
/
/e
/
/
lWY obert E. Hall, Group Leader Reactor Engineering Analysis REH:lz
~
Enclosure cc:
R. Cerbone (wo/ enc.)
W. Kato E. MacDougall V. Panciera (wo/ enc.)
E. Sylvester fCOL s
1707 215
/h noo:
c e I
g pensosed '
8001000
'3 4 6
Haddam Neck FIRE PROTECTION REVIEW Item 3.2.3 Fire Barrtuf_ Penetration Test Data Section 3.2.3 of the SER indicates that the licensee will provide test data which demonstrates that the existing fire barrier penetration seals have a fire rating of three hours.
The licensee submitted, in their July 31, 1979 letter, test information on the Dow Corning Q3-6548 medium density Silicone RTV foam. The tests indicated that the mat wial was subjected to the ASTM E119-73 Fire Endurance Test and success-fully passed the test. The licensee did not indicate that the penetrations in-stalled at the plant were similar to the tested penetration seals.
The licensee was requested to submit a letter verifying that the plant's penetration was sim-ilar in construction to the ones tested.
The licensee responded to this request in a letter dated October 9,1979. The installer of the penetration seals, Insulation Consultants and Management Services, Inc., certified that all the penetration seals had been installed to provide a three (3) hour fire rating. The only exceptions are in the switchgear room, and these will meet the one (1) hour fire rating as required in the SER.
The test procedure does not require positive pressure on the fire side; in actu-ality it is generally negative but as close to zero as possible.
The majority of testing on fire barrier penetrations to date has been conducted with negative pressure on the fire side. Most furnaces used for this testing are not designed to maintain any significant positive pressures on the fire side. Extensive modifications to the furnaces are necessary to conduct the tests.
IEEE Standard 634-1978 recognizes that a positive pressure on the fire side is desirable, but they also recognize that there has been no standard method pro-posed and accepted for checking the seal during fire tests.
Underwriters Laboratories, Inc. procedure, titled " ASTM Designation E, Standard Method of Fire Tests of Electrical and Mechanical Through-Penetration Fire Pops, July 28, 1977," also recognizes that a positive pressure on the fire side is desirable. However, due to the inability of many existing test furnaces to conduct fire tests under positive pressure, they recommend that the pressure on the fire side should be as close to atmospheric as possible.
There is a good possibility that the application of a ap across the penetration will affect the outcome of the test, whichever way the o p is applied. However, we are unable to find any data which substantiate a significant difference in test results. We do feel that this area deserves further exploration.
1707 216 e
., Further, to require a positive pressure on the fire side of the penetration seal under test would be inconsistent with the test methods used for determining the fire resistance ratings of wall and ceiling assemblies and protective devices
' or other wall and floor openings, e.g., fire doors, which are almost exclusive-ly tested with a slightly negative pressure on the exposed side of the test specimen.
For these reasons, we recommend that the documentation for the penetration seals at Haddam Neck be accepted.
1707 217