ML051390178
| ML051390178 | |
| Person / Time | |
|---|---|
| Site: | Millstone  |
| Issue date: | 01/24/2005 |
| From: | Price J Dominion Nuclear Connecticut |
| To: | Conte R NRC/RGN-I/DRS/OSB |
| Conte R | |
| References | |
| Download: ML051390178 (41) | |
Text
ES-401 PWR Examination Outline Form ES-401-2 Facility: Millstone Unit 2 Date of Exam: 03/21105 I I II Note: 1. Ensure that at least two topics from every applicable WA category are sampled within each tier of the RO and SRO-only outlines (Le., except for one category in Tier 3 of the SRO-only outline, the "Tier Totals" in each WA category shall not be less than two).
- 2. The point total for each group and tier in the proposed outline must match that specified in the table.
The final point total for each group and tier may deviate by il from that specified in the table based on NRC revisions. The final RO exam must total 75 points and the SRO-only exam must total 25 points.
- 3. Systerns/evolutions within each group are identified on the associated outline; systems or evolutions that do not apply at the facility should be deleted and justified; operationally important, site-specific systems that are not included on the outline should be added. Refer to ES-401, Attachment 2, for guidance regardingthe elimination of inappropriateWA statements.
- 4. Select topics f m as many systems and evolutions as possible; sample every system or evolution in the group before selecting a second topic for any system or evolution.
- 5. Absent a plant-specific priority, only those WAS having an importance rating (IR) of 2.5 or higher shall be selected. Use the RO and SRO ratings for the RO and SRO-only portions, respectively.
- 6. Select SRO topics for Tiers 1 and 2 from the shaded systems and WA categories.
7.' The generic (G) WAS in Tiers 1 and 2 shall be selected from Section 2 of the WA Catalog, but the topics must be relevant to the applicable evolution or system.
- 8. On the following pages, enter the WA numbers, a brief description of each topic, the topics' importance ratings (IRs) for the applicable license level, and the point totals (#) for each system and category. Enter the group and tier totals for each category in the table above. Use duplicate pages for RO and SRO-only exams.
- 9. For Tier 3,select topics from Section 2 of the WA catalog, and enter the WA numbers, descriptions, IRs, and point totals (#) on Form ES-401-3. Limit SRO selections to WAS that are linked to 10 CFR 55.43.
ES-401 2 Form ES-401-2 ES-401 PWR Examination Outline Form ES-401-2 ergency and Abnormal Plant Evolutions - Tier 1lGroup 1 (RO)
WAPE ##IName ISafety Function A G WA Topic@) IR #
3 000007 (BW/E02&E10; CEIEO2)
Reactor Trip Stabilization - I and emergency operating procedures Recovery I1 000008 Pressurizer Vapor Space Accident 1 3 000009 Small Break LOCA 1 3 000011 Large Break LOCA 1 3 000015117 RCP Malfunctions I 4 000022 Loss of Rx Coolant Makeup I 2 000025 Loss of RHR System 1 4 000026 Loss of Component Cooling Water 1 8 000027 Pressurizer Pressure Control System MalfunctionI 3 000029 ATWSI1 000038 Steam Gen. Tube Rupture I 3 000040 (BWIEOS; CWEO5; WlE12) EA1.l Ability to operate and I or monitor the following as they apply to the (Excess 3.9 1 Steam Line Rupture - Steam Demand): Components, and functions of control and safety systems, including Excessive Heat Transfer I 4 instrumentation, signals, interlocks, failure modes, and automatic and manual features.
Page 2 of 18 March 2005 Millstone Unit 2 NRC Exam Outline
Page 3 of 18 March 2005 Millstone Unit 2 NRC Exam Outline ES-401 3 Form ES-401-2 ES-401 PWR Examination Outline Form ES-401-2 nd At -
m a l Plant Evolutions Tier l/Group 2 (RO)
OAPE # / Name / Safety Function WA Topic@) IR #
000001 Continuous Rod Withdrawal / 1 AA1.05 Ability to operate and / or monitor the following as they apply to the 4.3 1 Continuous Rod Withdrawal : Reactor trip switches -
000003 Dropped Control Rod / 1 AA2.01 Ability to determine and interpret the following as they apply to the 3.9 1 Dropped Control Rod: Rod position indication to actual rod position -
000005 InoperabldStuckControl Rod / 1 AK3.05 Knowledge of the reasons for the following responses as they- apply.. - to the I 3.4 1 Inoperable / StuckControl Rod: Power limits on rod misalignment I I 000024 Emergency Boration / 1 000028 Pressurizer Level Malfunction/ 2 AK3.05 Knowledge of the reasons for the following responses as they apply to the 3.7 Pressurizer Level Control Malfunctions: Actions contained in EOP for PZR level malfunction I1 000032 000033 Loss of Source Range NI I 7 Loss of Intermediate Range NI I 7 AK3.02 Knowledge of the reasons for the following responses as they apply to the Loss of Source Range Nuclear Instrumentation: Guidance contained in EOP for loss of source-range nuclear instrumentation 2.3.4 Knowledge of radiation expcsure limits and contaminationcontrol, including 3.7 2.5 permissible levels in excess of those authorized 000036 (BW/A08) Fuel Handling Accident / 8 000037 Steam Generator Tube Leak I 3 000051 Loss of Condenser Vacuum / 4 000059 Accidental Liquid RadWaste Rel. I 9 AA2.06 Ability to determine and interpret the following as they apply to the 3.5 1 Accidental Liquid Radwaste Release: That the flow rate of the liquid being released is less than or equal to that specified on the release permit 000060 Accidental Gaseous Radwaste Rel. / 9 000061 ARM System Alarms / 7 000067 Plant Fire On-site / 8 AA1.09 Ability to operate and I or monitor the following as they apply to the Plant 3.0 1 Fire on Site: Plant fire zone panel (including detector location) 000068 (BW/A06) Control Room Evac. I 8 AK2.02 Knowledge of the interrelations between the Control Room Evacuation 3.7 1 and the following: Reactor trip system Page4of 18 March 2005 Millstone Unit 2 NRC Exam Outline
Page 5 of I8 March 2005 Millstone Unit 2 NRC Exam Outline ES-401 4 Form ES-401-2 ES-401 PWR Examination Outline Form E Plant Systems Tier UGroup 1 (RO)
K K A A A A G WA Topic@) IR 5 6 1 2 3 4 K5.94 Knowledge of the operational implications of the following concepts as 3.2 2 they apply to the RCPS: Effects of RCP shutdown on secondary parameters, such as steam pressure, steam flow, and feed flow Al.03 Ability to predict and/or monitor changes in parameters (to prevent 2.6 exceeding design limits) associated with operating the RCPS controls including: RCP motor stator winding temperatures operate and/or monitor in the control room: 1 1
7 1
Al.03 Ability to predict and/or monitor changes in parameters (to prevent on the following: -CRDS X A3.02 Ability to monitor automatic operation of the RPS, including: Bistables 3.6 X A2.04 Ability to (a) predict the impacts of the following malfunctionsor 3.6 operations on the ESFAS; and (b) based on those predictions, use procedures to correct, control, or mitigate the consequences of those malfunctionsor operations: Loss of instrument bus Page 6 of 18 March 2005 Millstone Unit 2 NRC Exam Outline
cu I" -I- cu
-L4-a 0 I-n r
c 0
3 u) 8 t
a
.-C
+ X 1
operations on the SWS; and (b) based on those predictions,use procedures to correct, control, or mitigate the consequencesof those malfunctionsor 078 InstrumentAir for the following: Cross-over to other air systems Page 8 of 18 March 2005 Millstone Unit 2 NRC Exam Outline
~~
PWR Examination Outline Form ES-401-2 System # / Name WA Topic@)
041 Steam DumWTurbine Page 9 of 18 March 2005 Millstone Unit 2 NRC Exam Outline
045 Main Turbine Generator X A2.08 Ability to (a) predict the impacts of the following malfunctions or 2.8 1 operation on the MT/G system; and (b) based on those predictions, use s
procedures to correct, control, or mitigate the consequences of those malfunctions or operations: Steam dumps are not cycling properly at low load, or stick open at higher load (isolate and use atmospheric reliefs when necessary) 055 Condenser Air Removal 056 Condensate 068 Liquid Radwaste 071 Waste Gas Disposal 072 Area Radiation Monitoring I 075 CirculatingWater WA Category Point Totals: 0 1 0 Group Point Total: 10 Page lOof 18 March 2005 Millstone Unit 2 NRC Exam Outline
ES-401 2 Form ES-401-2 ES-401 PWR Examination Outline F o ES-401-2
~
WAPE # I Name I Safety Function K 1
000007 (BWIEOPIE10; CEE02) 1 Reactor Trip Stabilization -
RecoveryI 1 -
OOOOO8 Pressurizer Vapor Space Accident I 3 000015117 RCP Malfunctions I 4 I 000022 Loss of Ax Coolant Makeup I X 2.2.12 Knowledge of surveillance procedures 3.4 2
000025 Loss of RHR System 1 4 I -
000026 Loss of Component Cooling 1 Water I 8 000027 Pressurizer Pressure Control 000029 ATWSII X EA2.09 Ability to determine or interpret the following as they apply to a ATWS: 4.5 1 Occurrence of a main turbine1reactor trip -
000038 Steam Gen. Tube Rupture I 3 X 2.1.23 Ability to perform specific system and integraed plant procedures during all 4.0 1 modes of plant operation 000040 (BWlEO5; CUE05; WIE12) X 2.4.49 Ability to perform without reference to procedures those actions that require 4.0 Steam Line Rupture - immediate operation of system compoonents and controls Excessive Heat Transfer I 4 000054 (CWEO6) Loss of Main Feedwater I 4 000055 Station Blackout I 6 Page 11 of 18 March 2005 Millstone Unit 2 NRC Exam Outline
BWlE04; WIE05 Inadequate Heat Transfer - Loss of Secondary Heat Sink I Page 12of 18 March 2005 Millstone Unit 2 NRC Exam Outline
ES-401 3 Form ES-401-2 ES-401 PWR Examination Outline Form ES-401-2 000067 Plant Fire Onalte / 8 Page 13of 18 March 2005 Millstone Unit 2 NRC Exam Outline
BWIEO9; CWA13; WlE09&E10 Natural Circ. I 4 BWE13 & E14 EOP R & ' h Endosurb ' 2 + .
I CElAll ;W E 0 8 RCS Overcooling PTS I 4 CWA16 Excess RCS Leakage I 2 IIII CUE09 Functional Recovery WA Category Point Totals: I 4 01 Group Point Total: 4 Page I4 of I8 March 2005 Millstone Unit 2 NRC Exam Outline
ES-401 4 Form ES-401-2 003 Reactor Coolant Pump associatedwkh RCP motors, including faulty motors Page 15 of 18 March 2005 Millstone Unit 2 NRC Exam Outline
Page 16 of 18 March 2005 Millstone Unit 2 NRC Exam Outline 1 - 0 W
E 2
Z "D
c m
8 h
is-401 Generic Knowledge and Abilities Outline (Tier 3) Form ES-401-3 Facility: Mills ne Unit 2 Date of Exam: 031 I lo5 I
Category WA # Topic RO SRO;Onlr, IR #
2.1.7 Ability to evaluate plant performance and make operational 3.7 1 judgments based on operating characteristics, reactor behavior, and
- 1. instrument interpretation Conduct of Operations 2.1.10 Knowledge of conditions and limitations in the facility license (43.2) 2.1.14 Knowledge of system status criteria which require the notification of 2.5 1 2.
Equipment Control 3.
Radiation Control 4.
Emergency Procedures1 Plan t
Tier 3 Point Tota
ES-401 Record of Rejected WAS Form ES-401-4 Randomly Reason for Rejection Selected WA 073. K4.02 Not applicable to Millstone Unit 2. CVCS letdown does not auto isolate on high radiation. Selected 073.K4.01.
2.1.16 Ability to operate plant phone demonstrated during simulator operating test. Randomly selected alternate GKA 2.1.14.
2.1.16 Ability to operate plant phone demonstrated during simulator operating test. Randomly selected alternate GKA 2.2.1 2 2.1.6 Ability to supervise and assume a management role during plant transients and upset conditions demonstrated during simulator operating test. Randomly selected alternate GKA
Serial No. 04-570A Attachment 1, Page 1 Attachment 1 SENIOR REACTOR AND REACTOR OPERATOR INITIAL EXAMINATIONS OPERATING EXAIMINATION OUTLINES Millstone Power Station Unit 2 Dominion Nuclear Connecticut, Inc. (DNC)
1Dominion I Mr. R. J. Conte, Chief Serial No. 04-570A Operational Safety Branch MPS Lic/BAK RO U.S. Nuclear Regulatory Commission Docket No. 50-336 Region I License No. DPR-65 475 Allendale Road King of Prussia, PA 19406-1415 DOMlNION NUCLEAR CONNECTICUT, INC.
MILLSTONE POWER STATION UNIT 2 SENIOR REACTOR AND REACTOR OPERATOR INITIAL EXAMINATIONS This letter is provided in response to the request from your office, dated September 2, 2004, to furnish the operating examination outlines by January 3, 2005, for Senior Reactor and Reactor Operator Initial Examinations at Millstone Power Station Unit 2.
Pursuant to 10 CFR 55.40(b)(3), an authorized station representative has approved the outlines contained in Attachment 1. The enclosed materials are complete and ready-to-use.
Consistent with the guidance contained in NUREG-1021 Examiners Standard 201, , the examination outline contained in Attachment 1 should be withheld from public disclosure until after the examination has been completed. No redacted versions are being supplied.
If you have any questions or require additional information, please contact Mr. Michael J. Wilson at (860) 437-2916.
Very truly yours, w-J AI n Price W V i c e President - Millstone 1
R.J. Conte letter from the U.S. Nuclear Regulatory Commission to D.A. Christian, Senior Reactor and Reactor Operator Initial Examinations - Millstone Unit 2, dated September 2, 2004.
Serial No. 04-570A Senior Reactor and Reactor Operator Initial Examinations Page 2 of 2 Attachments: 1 Commitments made in this letter: None.
cc: w/o attachment U.S. Nuclear Regulatory Commission Region I 475 Allendale Road King of Prussia, PA 19406-1415 Mr. V. Nerses Senior Project Manager U.S. Nuclear Regulatory Commission One White Flint North 11555 Rockville Pike Mail Stop 8C2 Rockville, MD 20852-2738 Mr. S. M. Schneider NRC Senior Resident Inspector Millstone Power Station U.S. Nuclear Regulatory Commission Attention: Document Control Desk Washington, DC 20555
ES-301 Control Room/ln-Plant Systems Outline Form ES-301-2 Facility: Millstone Unit 2 Date of Examination: 3/21/05 Exam Level (circle one): / SRO(I) / SRO(U) Operating Test No.: 1 Control Room Systems (8 for RO; 7 for SRO-I; 2 or 3 for SRO-U)
System / JPM Title Type Code* Safety Function
- a. Manual Makeup to the VCT: At the completion of this JPM, the D, S 1 examinee completes a manual blended make up to the VCT. (004 A2.06) (RO & SRO)
~
- b. Fill # I Safetv lniection Tank: When the examinee begins to fill # I A. M. S 3 Safety Injection Tank to between 55.2% and 59.3%, the A HPSl Pump trips. The examinee will declare the A HPSl Pump inoperable, place the B HPSl Pump in service on Facility 1, and complete filling
- c. Start 4hRCP; The examinee will start the RCP, monitor critical RCP A. N, L. S parameters, including alarms, and secure the RCP per OP 2301C and/or ARP 25908-083. (003 A2.03) (RO & SRO)
- d. Perform TDAFP Operabilitv Test: Examinee completes the assigned section of 2610B, determines that the TDAFP is not operable, and shuts down the pump. (061 A2.04) (RO & SRO)
~~
e A DG Operability Test (Alternate Path) Examinee performs the 6 Facility 1 Diesel Generator Operability Test, SP 2613A, on the A D/G, recognizes the D/G 12U Trouble annunciator Upon receipt of information from the PEO in the diesel room the examinee trips the A D/G (064 A4 01) (RO) f Power Ranqe Safetv Channel and Delta T Power Channel 7 Calibration During the performance of SP 2601 D, Power Range Safety Channel and Delta T Power Channel Calibration, the examinee determines that the -10 Volt power Supply voltage is not in the acceptable range and bypasses the channel (012 A2 04) (RO & SRO) g Placinq B RBCCW Pump and Heat ExchanQer in Service and D. S Removinq A RBCCW Pump and Heat Exchanqer The examinee places B RBCCW Pump and Heat Exchanger in service in place of A RBCCW Pump and Heat Exchanger (008 A4 01) (RO & SRO) h Change the Alarm Setpoint of the SJAE RM 5099 The examinee will N. S adjust the setpoint of the Steam Jet Air Ejector Radmonitor as specified on the attached SP2833-007 (071 A4 25) (RO & SRO)
I (SPARE) Hvdroqen Recombiner Surveillance At the completion of A. D. S 5 this JPM the examinee will have A Hydrogen Recombiner in service in accordance with SP 2608A (028 A4 01) (RO & SRO)
ES-301, Page 23 of 27 In-Plant Systems@(3 for RO; 3 for SRO-I; 3 or 2 for SRO-U)
- a. Removinq Section 201A-I, of Battery Charger 201A, From Service: At the completion of this JPM, battery charger section 201A-1 will be removed from service in accordance with 2345C section 4.13.
I 1063 K1.03) (RO & SRO) b Local Manual Operation of the A Atmospheric Dump Valve Examinee has taken local manual control of the A ADV and placed in D. E. L, R 1 4 (S) to 25% open per OP 2316A (041 A2 03) (RO & SRO) c Cross-Tie Station Air With Unit 3 to Supply Unit 2 Instrument Air E. L, N 8 The examinee has successfully performed the alignment to allow Unit 3 d
to supply Unit 2 with Station Air and to permit Station Air to supply Instrument Air (079 A2 01) (RO & SRO)
(SPARE) Loss of SDC/ Vent the A LPSl Pp. At the completion of this JPM the examinee will have simulated venting the A LPSl Pp uer AOP 2572 Loss of SDC 1005 A2 031 (RO & SROJ Ir/l E. L, N,R
- Type Codes Criteria for RO / SRO-I I SRO-U
Appendix D Scenario Outline Form ES-D-1
~ ~~
Facility: MP2 Scenario No.: ES04LI1 Op-Test No.: 1 Examiners: Operators:
Initial Conditions: 100% Power, EOL. RCS Boron is 35 ppm, Equilibrium Xenon, Bus 24E is aligned to Bus 24D. SG blowdown is 25 gpm on each SG. All swing components are aligned to Facilitv 2, Facilitv 2 is protected. Four hours prior to this shift, a minor earthquake, (0.09 g ZPA) was felt. No equipment is out of service.
Turnover:
100% Power. Facility 2 is protected. RCS Boron is 35 ppm, Blend ratio is 165:l. SGBD @ 25 gpm per SG, 24E aligned to 24D, Minor earthquake about 4 hour4.62963e-5 days <br />0.00111 hours <br />6.613757e-6 weeks <br />1.522e-6 months <br /> ago. All actions for AOP 2562, Earthquake, are complete. No apparent equipment damage. No equipment 00s. Need to perform SP 2654B, Forcing Sprays.
I Event I Malf. 1 Event 1 Event No. No. Type* Description 1 NIA N (ATC) Commence Forcing Sprays IAW SP 2654B.
N (SRO) 2 SWOlC C (BOP) Loss of C Service Water Pump.
C (SRO) 3 FW38B I (BOP) Feedwater Heater 6A Level Transmitter, L-5043A, fails low.
I (SRO) 4 RCOSA C (ATC) Pressurizer Safety Valve, RC-200, leakage.
C (SRO) 5 NA R (ATC) Plant shutdown required by Tech Specs, using AOP 2575, R (SRO) Rapid Downpower.
N (BOP) 6 ~CO5A M (ALL) Pressurizer Safety Valve, RC-200, opens resulting in a LOCA and plant trip.
7 Alarm A-4 C (ATC) A Containment Air Cooling Fan high vibration alarm.
on C-01 C (SRO) 8 SG02A C (All) Tube rupture in # I SG.
l* (N)ormal, (R)eactivity, (I)nstrument, (C)omponent, (M)ajor Appendix D, Page 38 of 39
Appendix D Scenario Outline Form ES-D-1 Facility: MP2 Scenario No.: ES04L12 Op-Test No.: 2 Examiners: Operators:
Initial Conditions: 1% Power, EOL, RCS Boron is 466 ppm, Equilibrium Xenon, Bus 24E is aliqned to Bus 24C. SG blowdown is 40 qpm on each SG. Group 7 CEAs are at 120 steps, Facility 2 is protected. No equipment is out of service.
Turnover:
1YO Power. Facility 2 is protected. RCS Boron is 466 ppm, Blend ratio is 11.8: 1. SGBD CFiZ 40 qpm per SG, 24E aligned to 24C. A snow storm is in progress with sustained winds of 20-25 mph. Need to raise power to 4%, using PMW, to commence warming the main turbine. Reactor Engineering would like to leave Group 7 CEAs at 120 steps up to 5%
power to allow for better AS1 control when raising power above 5%. OP 2203, Plant Startup is complete up through step 4.5.10.
Event Malf. Event Event No. No. TY Pe* Description 1 NIA N (BOP) Raise power to 4%.
R (ATC) 2 CV28A I (ATC) PMW Addition Valve, CH-210X, fails open.
3 CW02D C (BOP) D Circulating Water Screen D/P increases causing loss of D Circulatina Water PumD.
4 RMOIO I (ATC) Control Room Ventilation Radiation Monitor, RM-9799A, fails high.
5 A h r m (2-8 C (BOP) #2 MSlV Low Air Pressure alarm on C-05.
on C-05 6 MSO6B C (BOP) #2 MSlV closes resulting in a plant trip and a steam line break WXQB M (ALL) upstream of #2 MSIV.
7 ED16B C (ALL) Loss of Vital Instrument Bus, VA 20.
I* (N)ormal, (R)eactivity, (I)nstrument, (C)omponent, (M)ajor Appendix D, Page 38 of 39
Appendix D Scenario Outline Form ES-D-1 Facility: MP2 Scenario No.: ES04L13 Op-Test No.: 3 Examiners: Operators:
Initial Conditions: 100% Power, BOL, RCS Boron is 1201 ppm, Equilibrium Xenon, Bus 24E is aligned to Bus 24C. SG blowdown is 40 qpm on each SG. Facilitv 1 is protected. The Turbine Driven Auxiliary Feed Pump is out of service. F-16 is out for filter replacement.
Turnover:
100% Power. RCS Boron is 1201 ppm, Equilibrium Xenon, Blend ratio is 3.4:1, SGBD @
40 gpm per SG. Bus 24E is aligned to Bus 24C. Facilitv 1 is protected. The Turbine Driven Auxiliary Feed Pump is out of service. Radwaste Fan, F-16 is out for filter replacement.
Containment pressure is approximatelv 21 inches. Containment will need to be depressurized. Steps 4.13.1 through 4.13.7 are complete in OP 2314B. Chemical use has been prohibited in the Enclosure Building for the past week.
Event I Malf. Event No. I No. Type*
1 2
II NA PCOl N (ATC)
C (ALL)
Depressurize Containment IAW OP 2314B, Containment and Enclosure Building Purge.
Loss of the Plant Process Computer 3
I NA R (ATC)
I (ATC)
Restore AS1 to the normal operating range using AOP 2575, Rapid Downpower to reduce power by approximately 5%
RP1OC Channel C Pressurizer Pressure transmitter fails low.
C (ALL) Degradation of condenser vacuum requiring a continued reduction of Dower usina AOP 2575. RaDid DownDower.
FW33 M (ALL) Loss of condenser vacuum requiring a plant trip and a loss of main feedwater.
7 I ED05C C (ALL) Overload trip of Bus 24C resulting in a complete loss of all feedwater.
I ES03J C (ATC) Failure of C HPSl to automatically start on SlAS resulting in loss of all HPSl PumDs.
(N)ormal, (R)eactivity, (I)nstrument, (C)omponent, (M)ajor Appendix D, Page 38 of 39
ES-301 Transient and Event Checklist Form ES-301-5 Facility: Aillsto ? 2 Date of Exam: 3/21/05 Operating Test No.: 1 A E Scenarios P v P E L N 1 2 3 4 I T I T ESO4Lll ES04 L I2 ES04L13 0 C CREW POSITION I CREW POSITION I CREW POSITION I CREW POSITION T A T N Y T P
- E
- RX NOR I/C
~
MAJ
-TS a
SRO-I
~
~
RX NOR I/C SRO-U MAJ ~
TS a
SRO-I
~
RX NOR I/C SRO-U MAJ ~
~
~
TS Instructions:
- 1. Circle the applicant level and enter the operating test number and Form ES-D-1 event numbers for each evolution type; TS are not applicable for RO applicants. ROs must serve in both the at the controls (ATC) and balance of plant (BOP) positions; Instant SROs must do one scenario, including at least two instrument or component (I/C) malfunctions and one major transient, in the ATC position.
- 2. Reactivity manipulations may be conducted under normal or controlled abnormal conditions (refer to Section D.5.d) but must be significant per Section C.2.a of Appendix D.
- Reactivity and normal evolutions may be replaced with additional instrument or component malfunctions on a l-for-1 basis.
- 3. Whenever practical, both instrument and component malfunctions should be included; only those that require verifiable actions that provide insight to the applicants competence count toward the minimum requirement.
ES-3-1, Page 26 of 27
ES-301 Administrative Topics Outline Form ES-301-1 1 Facility: Millstone Unit 2
- Date of Examination: 3/21/05 l Examination Level (circle one): -5W3
-~
Operating Test N u m b e r : L Administrative Topic Type Describe activity to be performed (see Note) Code*
Validate an ECP (Faulted): The examinee reviews the completed ECF Conduct of Operations N and determines that there is an error. (2.1.25)
RO Taq Clearance Preparation: At the completion of this JPM, the Equipment Control N examinee will present a recommended tagging clearance to the tagging authority. (2.2.13)
Review RWP and Survey Map: At the completion of this JPM the examinee has reviewed the applicable RWP and survey map to Radiation Control N determine the radiological requirements to perform the assigned task.
(2.3.10)
Use RATS to Determine and Prioritize the Safety Functions: The
~ Emergency Plan examinee will correctly identify and prioritize the Safety Function Success Paths. (2 4.4)
NOTE: All items (5 total) are required for SROs. RO applicants require only 4 items unless they are retakins only the administrative topics, when 5 are required.
(N)ew or (M)odified from bank (21)
(P)revious 2 exams (51; randomly selected)
(S)i mulator ES-301, Page 22 of 27
ES-301 Administrative Topics Outline Form ES-301-1 Facility: Millstone Unit 2 Date of Examination: 3/21/05 Examination Level (circle one): W /@ Operating Test Number: 2 Administrative Topic TY Pe Describe activity to be performed (see Note) Code*
SRO Shift Turnover: At the completion of this JPM, the Conduct of Operations N SRO has performed a review of turn over documents and found incorrect information related to a shift turnover. (2.1.3)
SRO Tag Clearance Approval: At the completion of this JPM, the examinee will have discovered that the tag out is in error. He will recommend the clearance not be approved unti Conduct of Operations N the Cross tie valve 2-CHW-125 is added to the clearance and the other Cross tie valve 2-CHW-124 is removed.
(2.1.24)
SRO AWO Acceptance: At the completion of this JPM, the Equipment Control N examinee will recommend the correct PMT, HPSl Pump IST (SP2604A-003). (2.2.21)
SRO Review and Approve a Radioactive Liquid Waste Release Permit: At the completion of this JPM, the Radiation Control N examinee will have discovered a plant operating condition that will NOT allow authorizing a radioactive liquid waste discharge. (2.3.6)
Classify the Event: At the completion of this JPM, the Emergency Plan examinee will determine the classification of the scenario to be an Alert/Cl. (2.4.41)
NOTE: All items (5 total) are required for SROs. RO applicants require only 4 items unless they are retaking only the administrative topics, when 5 are required.
(N)ew or (M)odified from bank (21)
(P)revious 2 exams (21; randomly selected)
(S)imulator ES-301, Page 22 of 27
ES-301 Control Room/ln-Plant Systems Outline Form ES-301-2 Facility: Millstone Unit 2 Date of Examination: 3/21/05 Exam Level (circle one): Operating Test No.: 1 Control Room Systems (8 for RO; 7 for SRO-I; 2 or 3 for SRO-U System / JPM Title Safety Function
- a. Manual Makeup to the VCT: At the completion of this JPM, the 1 examinee has recognized an inadvertent dilution in progress and recommends/secures the dilution. (004 A2.06) (RO & SRO)
- b. HPSl Pump Operabiliw Test: At the completion of this JPM, A, D, S 3 the examinee has initiated Facility I HPSl pump surveillance on A HPSl pump and recognized the failure of the pump to start, and states that the pump has failed its surveillance and/or that it is inoperable. (006 A4.06) (RO & SRO)
- c. Start 4hRCP; The examinee will start the RCP, monitor critical RCP parameters including alarms and secure the RCP per OP 2301C and/or ARP 25908-083. (003 A2.03) (RO & SRO)
- d. Perform TDAFP Operability Test: Examinee completes the A. N, S assigned section of 26106 and determines that the TDAFP is not operable. (061 A2.04) (RO & SRO)
- e. A DG Operability Test (Alternate Path): Examinee performs 6 the Facility 1 Diesel Generator Operability Test, SP 261 3A, on the A DIG, recognizes the DIG 12U Trouble annunciator.
Upon requesting information from the PEO in the diesel room, the examinee recommends, or trips the A D/G. (064 A4.01)
(RO)
Power Range Safety Channel and Delta T Power Channel 7
~
Calibration: During the performance of SP 2601 D, Power Range Safety Channel and Delta T Power Channel Calibration, the examinee determines that the -1 0 Volt power Supply voltage is not in the acceptable range and bypasses the channel. (012 A2.04) (RO & SRO)
- g. Placing B RBCCW Pump and Heat Exchanger in Service 8 and Removing A RBCCW Pump and Heat Exchanger:
During the swap of the A RBCCW Pump and Heat Exchanger to the 6 RBCCW Pump and Heat Exchanger, the examinee observes a problem with the B RBCCW Heat Exchanger and swaps back to the A RBCCW Heat Exchanger. (008 A2.03)
ES-301, Page 23 of 27
examinee will adjust the setpoint of the Steam Jet Air Ejector Radmonitor as specified on the attached SP2833-007. (071 1 A4.25) (RO & SRO) 1 I
- i. (SPARE) Hydroqen Recombiner Surveillance: At the A, D, S 1 completion of this JPM, the examinee will have A Hydrogen Recombiner in service in accordance with SP-2608A. (028 A4.01) (RO & SRO)
- c. Cross-Tie Station Air With Unit 3 to Supply Unit 2 E. L, N Instrument Air: The examinee has successfully performed the alignment to allow Unit 3 to supply Unit 2 with Station Air and to permit Station Air to supply Instrument Air. (079 A2.01) (RO &
SRO)
- d. (SPARE) Loss of SDC / Vent the A LPSl Pp.: At the 41 completion of this JPM, the examinee will have simulated venting the A LPSl Pp. per AOP 2572, Loss of SDC. (005 A2 03) (RO & SRO)
)II 1 @ All Control Room (and In-Plant) systems must be different and serve different safety functions: In-Plant svstems and functions mav overlaD those tested in the Control Ro
- Type Codes: Criteria for RO I SRO-I I SRO-U (A)Ite rnat e path ~ ~~
4-6 14-6 12-3 (C)ontrol room ~-
(D)irect from bank ~
(E)mergency or abnormal in-plant,
~
( L)ow - Powe r (N)ew or (M)odified from bank including 1(A)
~~
(P)revious 2 exams __
(R)CA (Shmulator
1Dominion AN 7 1 7m Mr. R. J. Conte, Chief Serial No. 04-570B Operational Safety Branch MPS Lic/BAK RO U.S. Nuclear Regulatory Commission Docket No. 50-336 Region I License No. DPR-65 475 Allendale Road King of Prussia, PA 19406-1415 This letter is provided in response to the request from your office, dated September 2, 2004, to furnish by February 8 , 2005, the proposed operating test and supporting documents for Senior Reactor and Reactor Operator Initial Examinations at Millstone Power Station Unit 2. of this letter transmits the operating examination materials which were developed in accordance with NUREG-I 021, Operator Licensing Examination Standards for Power Reactors, Revision 9, Examination Standard ES-301, Preparing Initial Operating Tests. Pursuant to 10 CFR 55.40(b)(3), an authorized station representative has approved the proposed operating tests contained in Attachment 1. contains the supporting documents. The attached materials are complete and ready for use.
Consistent with the guidance contained in NUREG-1021 Examiners Standard 201, , the attachments should be withheld from public disclosure until after the examination has been completed. No redacted versions are being supplied.
If you have any questions or require additional information, please contact Mr. Michael J. Wilson at (860) 437-2916.
Very truly yours,
- Millstone 1
R.J. Conte letter from the U.S.Nuclear Regulatory Commission to D.A. Christian, Senior Reactor and Reactor Operator Initial Examinations - Millstone Unit 2, dated September 2, 2004.
Serial No. 04-5708 Senior Reactor and Reactor Operator Initial Examinations Page 2 of 2 Attachments: 2 Commitments made in this letter: None.
cc: w/o attachment U.S. Nuclear Regulatory Commission Region I 475 Allendale Road King of Prussia, PA 19406-141 5 Mr. V. Nerses Senior Project Manager U.S. Nuclear Regulatory Commission One White Flint North 1 1555 Rockville Pike Mail Stop 8C2 Rockville, MD 20852-2738 Mr. S. M. Schneider NRC Senior Resident Inspector Millstone Power Station U.S. Nuclear Regulatory Commission Attention: Document Control Desk Washington, DC 20555
Serial No. 04-570B Attachment 1, Page 1 Attachment 1 SENIOR REACTOR AND REACTOR OPERATOR INITIAL EXAMINATIONS PROPOSED OPERATING TESTS Millstone Power Station Unit 2 Dominion Nuclear Connecticut, Inc. (DNC)
Serial No. 04-570B Attachment 2, Page 1 Attachment 2 SENIOR REACTOR AND REACTOR OPERATOR INITIAL EXAMINATIONS SUPPORTING DOCUMENTS Millstone Power Station Unit 2 Dominion Nuclear Connecticut, Inc. (DNC)
Appendix D Scenario 0utline Form ES-D-1 Facility: MP2 Scenario No.: ES04LI1 Op-Test No.: 1 Examiners: Operators:
Initial Conditions: 100% Power, EOL, RCS Boron is 35 ppm, Equilibrium Xenon, Bus 24E is aligned to Bus 24D. SG blowdown is 25 gpm on each SG. All swing components are aligned to Facility 2, Facility 2 is protected. Four hours prior to this shift, a minor earthquake, (0.09 g ZPA) was felt. No equipment is out of service.
Turnover :
100% Power. Facilitv 2 is protected. RCS Boron is 35 ppm, Blend ratio is 165:l. SGBD @ 25 gpm per SG, 24E aligned to 24D, Minor earthquake about 4 hour4.62963e-5 days <br />0.00111 hours <br />6.613757e-6 weeks <br />1.522e-6 months <br /> aqo. All actions for AOP 2562, Earthquake, are complete. No apparent equipment damage. No equipment 0 0 s . Need to perform SP 2654B, Forcing Sprays.
Event Event Type* Description 1 N/A N (ATC) Commence Forcing Sprays IAW SP 2654B.
N (SRO) 3 I
~
swOc FW38B C (BOP)
C (SRO)
I (BOP)
Loss of C Service Water Pump.
Feedwater Heater 6A Level Transmitter, L-5043A, fails low I (SRO) 4 1 RC05A C (ATC) Pressurizer Safety Valve, RC-200, leakage C (SRO)
R (ALL) Plant shutdown required by Tech Specs, using AOP 2575, N (ALL) Rapid Downpower.
6 1 RC05A C (ATC) Pressurizer Safety Valve, RC-200, opens resulting in a C (SRO) LOCA and plant trip.
M (ALL)
Alarm A-4 C (ATC) A Containment Air Cooling Fan high vibration alarm on C-01 C (SRO) ~
SG02A C (BOP) Tube rupture in #I SG.
C (SRO)
L M (ALL)
- (N)ormal, (R)eactivity, (I)nstrument, (C)omponent, (M)ajor Appendix D, Page 38 of 39
Appendix D Scenario Out Ii ne Form ES-D-1 Facility: MP2 Scenario No.: ES04L12 Op-Test No.: 2 Examiners: Operators:
Initial Conditions: 1% Power, EOL, RCS Boron is 466 ppm, Equilibrium Xenon, Bus 24E is aligned to Bus 24C. SG blowdown is 40 gpm on each SG. Group 7 CEAs are at 120 steps, Facility 2 is protected. No equipment is out of service.
Turnover:
1% Power. Facilitv 2 is protected. RCS Boron is 466 ppm, Blend ratio is 11.8:l. SGBD @
40 gpm per SG, 24E aligned to 24C. A snow storm is in progress with sustained winds of 20-25 mph. Need to raise power to 4%, using PMW, to commence warming the main turbine and to start a main feed pump. Reactor Enqineering would like to leave Group 7 CEAs at 120 steps up to 5% power to allow for better AS1 control when raising power above 5%. OP 2203, Plant Startup is complete up through step 4.3.20, establishing a condenser Event Malf. Event Event NO. 1 NO. Type* Description 1 ' N/A N (ALL) Raise power to 4%.
R (ATC)
CV28A I (ATC) PMW Addition Valve, CH-210X, fails open.
C (BOP) "D" Circulating Water Screen DIP increases causing loss of "D" Circulating Water Pump.
4 j RMOIO I (ATC) Control Room Ventilation Radiation Monitor, RM-9799A, fails high.
5 ~ Alarm C-8 C (BOP) #2 MSlV Low Air Pressure alarm on C-05.
on C-05 6 MSR16 C (ALL) #2 MSlV closes resulting in a plant trip and a steam line break MS02B M (ALL) upstream of #2 MSIV.
7 ED16B C (ALL) Loss of Vital Instrument Bus, VA 20.
M (ALL) k (N)ormal, (R)eactivity, (I)nstrument, (C)omponent, (M)ajor Appendix D, Page 38 of 39
Appendix D Scenario Outline Form ES-D-1 Facility: MP2 Scenario No.: ES04L13 Op-Test No.: 3 Examiners: Operators:
Initial Conditions: 100% Power, BOL, RCS Boron is 1201 ppm, Equilibrium Xenon, Bus 24E is aliqned to Bus 24C. SG blowdown is 40 qpm on each SG. Facility 1 is protected. The Turbine Driven Auxiliary Feed Pump is out of service.
Turnover:
100% Power. RCS Boron is 1201 ppm, Equilibrium Xenon, Blend ratio is 3.9:1, SGBD @
40 qpm per SG. Bus 24E is aliqned to Bus 24C. Facility 1 is protected. The Turbine Driven Auxiliary Feed Pump is out of service. Containment pressure is approximately 22 inches.
Containment will need to be depressurized. Steps 4.13.1 throuqh 4.13.7 are complete in OP Event Event TY Pe* Description N (ATC) Depressurize Containment IAW OP 2314B, Containment and Enclosure Building Purge.
C (ALL) Loss of the Plant Process Computer R (ALL) Restore AS1 to the normal operating range using AOP 2575, Rapid N (ALL) Downpower to reduce power by approximately 5%
I (ATC) Channel C Pressurizer Pressure transmitter fails low. -
C (ALL) Degradation of condenser vacuum requiring a continued reduction of power using AOP 2575, Rapid Downpower.
C (ALL) Loss of condenser vacuum requiring a plant trip and a loss of main M (ALL) feedwater.
C (ALL) Overload trip of Bus 24C resulting in a complete loss of all feedwater.
M (ALL)
C (ATC) Failure of C HPSl to automatically start on SlAS resulting in loss of all HPSl Pumps.
- (N)ormal, (R)eactivity, (I)nstrument, (C)omponent, (M)ajor 11 Appendix D, Page 38 of 39
ES-301 Transient and Event Checklist Form ES-30 1-5
~~ ~~~
[Faclllty E Scenarios V
I E N 1 2 3 4 / T I M C
A T
T I ES04LI1 CREW POSITION ~
ES04L12 CREW POSITION 1 ES04L13 CREW POSITION ~
j CREW POSITION 1 I 0
T A i l 1
N N Y S A B S A B S A B S A B L ~ M P R T O R T O R T O R T O I "
1 Instructions:
I Circle the applicant level and enter the operating test number and Form ES-D-1 event numbers for each
~ 1
~
evolution type; TS are not applicable for RO applicants. ROs must serve in both the "at the controls (ATC)"
~
and "balance of plant (BOP)" positions; Instant SROs must do one scenario, including at least two instrument
~
or component (I/C) malfunctions and one major transient, in the ATC position.
~ 2 Reactivity manipulations may be conducted under normal or controlled abnormal conditions (refer to Section
~
D.5.d) but must be significant per Section C.2.a of Appendix D.
- Reactivity and normal evolutions may be
~
replaced with additional instrument or component malfunctions on a I-for-1 basis.
~ 3. Whenever practical, both instrument and component malfunctions should be included; only those that require
~
verifiable actions that provide insight to the applicant's competence count toward the minimum requirement.
Author NRC Reviewer.
J ES-3-1, Page 26 of 27