Pages that link to "05000366/LER-1978-061, Forwards LER 78-061/03L-0"
Jump to navigation
Jump to search
The following pages link to 05000366/LER-1978-061, Forwards LER 78-061/03L-0:
Displayed 27 items.
- 05000366/LER-1978-053, Forwards LER 78-053/03L-0 (← links)
- 05000366/LER-1978-054, Forwards LER 78-054/01T-0 (← links)
- 05000366/LER-1978-039, Forwards LER 78-039/03L-0 (← links)
- 05000366/LER-1978-035, Forwards LER 78-035/03L-0 (← links)
- 05000366/LER-1978-043, Forwards LER 78-043/03L-0 (← links)
- 05000366/LER-1978-047, Forwards LER 78-047/03L-0 (← links)
- 05000366/LER-1978-041, Forwards LER 78-041/03L-0 (← links)
- ML20197D138 (redirect page) (← links)
- PM-78-432, Forwards LER 78-061/03L-0 (redirect page) (← links)
- PM-78-432 (redirect page) (← links)
- 05000366/LER-1978-061-03, /03L-0 on 781029:during Scram 2-78-14,2B21-NO24A Instru Switch 2 Failed to Actuate at Setpoint 111.6+/-3.6 Inches.Cause:Magnet on 2 Switch Had Metal Shavings on It. Instru Cover Was Loose & Shavings Entered Instru (← links)
- 05000366/LER-1978-061, Forwards LER 78-061/03L-0 (← links)
- 05000366/LER-1978-061-03, /03L-0 on 781029:during Scram 2-78-14,2B21-NO24A Instru Switch 2 Failed to Actuate at Setpoint 111.6+/-3.6 Inches.Cause:Magnet on 2 Switch Had Metal Shavings on It. Instru Cover Was Loose & Shavings Entered Instru (← links)
- 05000366/LER-1978-061 (redirect page) (← links)
- 05000366/LER-1978-060-03, /03L-0 on 781031:during Procedure HNP-2-10531 & Reactor in Run Mode,The 2R43-S001 C Diesel Failed to Reach 250 RPM W/In 7 Seconds,Due to Faulty Elec Speed Switch Signal (← links)
- 05000366/LER-1978-060, Forwards LER 78-060/03l-0 (← links)
- 05000366/LER-1978-051-03, /03L-0 on 781017:during Startup Testing While Calibrating APRM High Flux Scram Setpoints,Discerned That Trip Setpoints Were Set in Excess of Reg Guide Criteria. Caused by Deficiency in Procedures (← links)
- 05000366/LER-1978-058-03, /03L-0 on 781018:hose Stations Were Not Inspected as Req by Tech Spec.Caused by Changeover in Procedures, Resulting in Oversight.Personnel Instructed & New Procedures Implemented (← links)
- 05000366/LER-1978-058, Forwards LER 78-058/03L-0 (← links)
- 05000366/LER-1978-056-03, /03l-0 on 781027:while Performing Procedure HNP-2-10315,2E41-F001 Valve Failed to Oper During HPCI Quick Start.Caused by Motor Shunt Field Insulation Failure (← links)
- 05000366/LER-1978-056, Forwards LER 78-056/03l-0 (← links)
- 05000366/LER-1978-063-03, /03L-0 on 781102:reactor Maximum Cooldown Rate of 100 Degrees F Exceeded During Reactor Auto Scram & Vessel Depressurization.Caused by Personnel Error;Personnel Have Been Admonished (← links)
- 05000366/LER-1978-076-03, /03L-0 on 781205:w/reactor in Run Mode During Special Inspec of 3-hour Fire Barriers,A Manila Rope Was Found Thru Fire Seal of Cable Tray 2BHA902 in the RPS M.G. Set Room,Due to Constr Personnel Error (← links)
- 05000366/LER-1978-078-03, /03L-0 on 781207:during Normal Oper & Performance of Procedure HNP-2-3307,HPCI Steam Line Flow Ft&C Switch 2E41-N004 Was at -217 in Water,Due to Instru Drift (← links)
- 05000366/LER-1978-079-03, /03L-0 on 781208:during Steady State Oper,During Procedure HNP-2-3410,2E51-N017 Would Trip at -116 of Water for Low Setpoint & 111.9 of Water at High Setpoint,Due to Instru Drift (← links)
- 05000366/LER-1978-032-03, /03L-0:on 780916,continuous Fire Watch Not Established at Unsealed Conduit.When Failure Was Recognized, Continuous Fire Watch Immediately Established.Shift Foreman Supervisors Made Aware of Conditions to Prevent Recurrence (← links)
- 05000366/LER-1978-046-03, /03L-0:on 780926,rated Flow W/Two Pumps Running in Loop 1 Could Not Be Achieved for Either Loop of RHR Svc Water Pump.Caused by Damaged Cavitrol V Trims & 10 Inch Fisher Valves (← links)
- 05000366/LER-1978-033-03, /03L-0:on 780915,during Plant Startup,Drywell Pressure Exceeded 0.75 Psig Tech Spec Limit (← links)
- 05000366/LER-1978-034-03, /03L-0:on 780917,electrical Cables for Fire Dampers Between Generator & Battery Rooms Found Improperly Routed.Cables Rerouted (← links)
- 05000366/LER-1978-040-03, /03L-0:on 78092,switch 2B21-n010C Setpoint Found Higher than 200f.Caused by Drift of Temp Switch.Switch Recalibr (← links)