View source for E900-05-027, Experimental Corporation Final Status Survey Report for OL6 and OL10, Snec Calculation Sheet

{{Adams
| number = ML052010671
| issue date = 07/14/2005
| title = Experimental Corporation Final Status Survey Report for OL6 and OL10, Snec Calculation Sheet
| author name = 
| author affiliation = GPU Nuclear Corp
| addressee name = 
| addressee affiliation = NRC/Document Control Desk, NRC/NRR
| docket = 05000146
| license number = DPR-004
| contact person = 
| case reference number = E900-05-027, Rev 0
| document type = Calculation
| page count = 50
}}

=Text=
{{#Wiki_filter:ORIGI NAL SNEC CALCULATION COVER SHEET
                                                -CALCULATION DESCRIPTION Calculation Number                                           Revision Number           Effective Date                Page Number E900-05-027                                 lo0                                                                      I     of      9 Subject OL6 and OLIO Open Land Area - Survey Design Question 1 - Is this calculation defined as 'in QA Scope'? Refer to definition 3.5. Yes           0    No  El Question 2- Is this calculation defined as a 'Design Calculation"? Refer to definitions 3.2 and 3.3. Yes           0      No El NOTES: If a 'Yes answer is obtained for Question 1,the calculation must meet the requirements of the SNEC Facility Decommissioning Quality Assurance Plan. If a 'Yes' answer is obtained for Question 2. the Calculation Originator's immediate supervisor should not review the calculation as the Technical Reviewer.
DESCRIPTION OF REVISION "Non-substantive Chancges". Entry by B.H. Brosev. 7111105 Description of Change to Calculation                                                     Affected Pages Section 1.1, Corrected total area to 22,436 m2                                           2 of 9 Table 4. Corrected OL10-3 entry (it was incorrectly fisted as OL10-1)                    4 of 9 Replaced Attachment 2-1 to 2-3 which contained a missed piece of information that does   Attachment 2-1 to 2-3 not In any way impact the calculation. Sampled areas for two samples was In error.                             I APPROVAL SIGNATURES Technical Reviewer Additional Review Additional Review

f-                    SNEC CALCULATION SHEET Calculation Number                                          Revision Number                         Page Number E900-05-027                                                                  0                            Page 2 of 9 SAtec OL6 and OL10 Open Land Area - Survey Design 1.0 PURPOSE 1.1    The purpose of this calculation is to develop a survey design for SNEC site open land areas designated 0L6, and OL10 in the northern portion of the SNEC site. These areas are collectively -22.436 square meters in total surface area, and are divided into three (3) -
Class 2 survey units and one (1) Class 1 survey unit. This design applies only to open land areas. Additional designs may be developed for structural surfaces in these areas as deemed appropriate by SNEC management (where applicable). These areas are shown on Attachment 1-1.
1.2 OL10 is sub-divided into three (3) survey units while OL6 is considered one survey unit even though it is located in three (3) separate locations. These survey units have the following approximate surface areas:
* OL10-1, -6,800 square meters,
* OL10-2, -6,860 square meters,
* 0L1 -3, -7,000 square meters, and
* 0L6, -1,775 square meters 2.0 

==SUMMARY==
OF RESULTS The following information should be used to develop a survey request for these survey units.
The effective DCGLw value is listed below for these survey units. The US NRC has reviewed and concurred with the methodology used to derive these values. See Attachment 2-1 through 2-3.
This mix is developed from samples taken from the OL6 area.
Table 1, DCGLw Values l SurveyUnits l VolumetricDCGLw(pC1g-Cs-137)           l All                 6.54 (4.9 A.L.)
NOTE. A.L Is the site Administrative Umit (75% of effective DCGLw) 2.1    Survey Design 2.1.1   Scanning of soil (and fill materials) shall be performed using a 2" D by 2" L Na!
detector with a Cs-1 37 window setting (Reference 3.1). The window shall straddle the Cs-137 662 keV full energy peak width (see typical calibration information on Attachment 3-1).
2.1.2 The instrument conversion factorlefficiency shall not be less than 206 cpmluRth -
Cs-137.
2.1.3 Other instruments of the type specified in Section 2.1.1 above may be used during the final status survey (FSS), but must demonstrate detection efficiencies at or above the value listed in Section 2.1.2.

nt_                        SNEC CALCULATION SHEET Calculation Number                                               Revision Number                      Page Number E900-05-027                                                                        0                        Page 3 of 9 Subject 0L6 and OL10 Open Land Area - Survey Design Table 2, Soil Scanning Parameters MDCscan (pCUg) - Cs-13rl Scan Speed (cmlsec)                 Maximum Distance from Surface 5.97                        25              4' (gap between detector face & soil surface)
See Attachment 4-1 through 4-3 for actual calculations' 2.1.4   If a count rate greater than the action level of Table 2 is encountered during the scanning process, the surveyor should stop and locate the boundary of the elevated area. The surveyor should then mark the elevated area with stakes and/or other appropriate marking methods. To complete the investigation, sample elevated areas(s) IAW SNEC procedure E900-IMP-4520.04 (Reference 3.2), and Section 2.2 of this calculation.
2.1.4.1 Class 1 and Class 2 soil should be scanned using a serpentine pattern that is
                                 -0.5 meters wide.
2.1.4.2 Scanning locations are randomly chosen on a per grid basis. Grids that can not be accessed should be clearly noted along with the reason for not completing the scan in that area. Scanning of partial grid areas is permitted with adequate documentation.
2.1.4.3The minimum number of scan locations are identified, and listed in Table 3 (see Attachment 5-1 for actual locations). Additional judgmentaVrandomly chosen grids are provided for the Class 2 areas so that a 50% scanning goal can be achieved even if some grid areas (or grid sections) are deemed inaccessible. There is no need to scan these extra grid areas if the minimum scanning goal is attained in the Class 2 areas (i.e., -50% coverage). Class 1 areas are scanned at 100% coverage for all available grids.
Table 3, Scanning Coverage Survey Unit          Target      Number of Grids to be Scanned Coverage OL10-1             -50%            34 needed (38 provided)
OL10-2             -50%            34 needed (38 provided)
OL10-3             -50%            35 needed (40 provided) 0L6 (all 3 sections)    -100%                  All available See Attachment 5-1.
2.1.5   The minimum number of randomly located sample points required for these survey units is listed in the following Table (see Compass output on Attachment 6-1 through 6-11). The surveyor should attempt to collect all samples listed below, but must collect the minimum values listed for each survey unit.

r_-                     SNEC CALCULATION SHEET Calculation Number                                            Revision Number                    Page Number E900-05-027                                                I                     0            l        Page 4 of 9 Subject 0L6 and OL10 Open Land Area - Survey Design Table 4, Randomly Located Sample Points Survey Unit                No. of Samples OL10-1                 14 min. (18 provided)
OL1-02                 14 min. (19 provided)
OL10-3                 14 min. (18 provided)
OL6                  16 min. (20 provided)
See Attachment 7-1 to 7.6 (7-6 = key (x, y) coordinates).
2.1.6 Sampling depth should be IAW Section 2.2.
2.1.7 Because the MDCscan (soil) is greater than the DCGLwc, 137. the Class 1 survey unit is evaluated lAW the 1Hot Spot" design criteria. No additional samples are necessary (see Attachment 6-11).
2.1.8 VSP (Reference 3.3) is used to plot some scan and sample point locations in the included diagrams (see Attachment 5-1, and 7-1 to 7-5). The actual number of random start systematically spaced measurement points may be greater than that required by the Compass computer code because of any or all of the following:
* placement of the initial random starting point (edge effects),
* odd shaped diagrams, and/or
* coverage concerns 2.1.11 The starting points for physically locating sample sites in these survey units are based on measurements from key site grid pins (see Attachment 7-1 to 7-5 and 7-6 for key x, y coordinates). Sampling points are positioned using coordinates/measurements developed from these markers and the current site grid map.
2.1.12 Some sampling points may need to be adjusted to accommodate obstructions within these survey units. Contact the SR coordinator to report any difficulties encountered when laying out sampling points.
2.1.13 When an obstruction is encountered that will not allow collection of a sample, contact the cognizant SR coordinatorfor permission to delete the sampling point.
NOTE If remediation actions are taken as a result of this survey, this survey design must be revised or re-written entirely.
2.2    Sample elevated areas(s) IAW SNEC procedure E900-IMP-4520.04 (Reference 3.2) and the following.
2.2.1 Collect one meter deep samples at all locations listed in Attachments 7-1 to 7-5.

K-                      SNEC CALCULATION SHEET Calculation Number                                         Revision Number                Page Number E900-05-027                                                               0                      Page 5 of 9 Subject OL6 and OL10 Open Land Area - Survey Design NOTE I Since the site surface dose model is 1 meter in depth, 1 meter deep samples must be collected to satisfy the initial sampling requirements of Section 2.1.5 (of this design).
Sections 4.2.3, 4.2.6 or 4.2.7 of site procedure E900-IMP-4520.04 are applicable when satisfying sampling requirements of this calculation.
2.2.2 Collect samples below one (1) meter (in 1 meter increments) to base materials (bed rock, bolder layers, etc.) at the following locations:
* in OL10-2, sample points 10, 12,16 & 18
* in OL6, sample point 15 NOTE 2 The area between grid lines -1 17 and -111, north of about the BJ grid line is an elevated area rising at least 8 feet above the surrounding grade. It appears to be a depository of building rubble and soils from earlier site excavations. Thus this area has been assigned several deep sampling requirements.
2.2.3 Clearly mark, identify and document all sample locations.
2.2.4 As a part of the investigation process, sample any location that is above the action level cited is Table 2.

==3.0 REFERENCES==

3.1    SNEC Calculation No. E900-03-018, 'Optimize Window and Threshold Settings for the Detection of Cs-137 Using the Ludlum 2350-1 and a 44/10 Nal Detector", 817/03.
3.2   SNEC Procedure E900-IMP-4520.04, 'Survey Methodology to Support SNEC License Termination".
3.3   Visual Sample Plan, Version 2.0 (or greater), Copyright 2002, Battelle Memorial Institute.
3.4   Compass Computer Program, Version 1.0.0, Oak Ridge Institute for Science and Education.
3.5    Plan SNEC Facility License Termination Plan.
3.6    SNEC Procedure E900-IMP-4500.59, uFinal Site Survey Planning and DQA7.
3.7    SNEC Survey Request No. SR-0151, SR-0152, SR-153, SR-0161, and SR-01163 covering areas in and around OL6 and OL10, August 2004.
3.8    GPU Nuclear, SNEC Facility, "Site Area Grid Map", SNECRM-020, Sheet 1, Rev 2, 1/29/03.
3.9    SNEC Calculation No. E900-03-012, Effective DCGL Worksheet Verification.
3.10   SNEC Procedure E900-IMP-4520.06, "Survey Unit Inspection in Support of FSS Design".
3.11   NUREG-1575, 'Multi-Agency Radiation Survey and Site Investigation Manual", August, 2000.
3.12   Microsoft Excel 97, Microsoft Corporation Inc., SR-2, 1985-1997.

Ap m                 SNEC CALCULATION SHEET Calculation Number                                       Revision Number                 Page Number E900-05-027                                            I0                                      Page 6 of 9 Subject OL6 and OL10 Open Land Area - Survey Design 4.0 ASSUMPTIONS AND BASIC DATA 4.1    The Compass computer program is used to calculate the required number of random start systematic samples to be taken in the survey unit (Reference 3.4).
4.2     Characterization soil samples from this area are used as the initial estimate of variability.
These results are shown on Attachment 8-1. The grid locations where these samples were taken are also shown (Reference 3.7).
4.3 The MARSSIM Sign Test is applicable for this survey design. No background subtraction will be performed under this criteria during the application of the DQA.
4.4 The number of points chosen by Compass are located on the survey map for the survey unit by the Visual Sample Plan (VSP) computer code (Reference 3.4).
4.5     Reference 3.5 and 3.6 were used as guidance during the survey design development phase.
4.6 Typical background values in the 0L6 and OL10 are less than 300 cpm (Reference 3.7).
For purposes of calculating the MDCscan value used for planning purposes, background is assumed to be approximately 200 cpm.
4.7    The site area drawing used to determine the physical extent of the area is listed as Reference 3.8.
4.8    Remediation History No significant remediation has occurred in the OL10 areas with respect to open land area.
No significant concrete structures exist in this area. Those that do exist will be addressed in separate survey designs as deemed appropriate by SNEC management.
0L6 areas have been remediated to a depth of several feet. Subsequent sampling has shown these areas to now be less than the applicable DCGLw. This area is a Class 1 area.
4.9 This survey design uses Cs-137 as a surrogate to bound the average concentration for all SNEC facility related radionuclides in the survey unit. The effective DCGLw is just the permitted Cs-137 concentration (6.6 pCi/g) lowered to compensate for the presence (or potential presence) of other SNEC related radionuclides. In addition, an administrative limit (75%) has been set that further lowers the permissible Cs-1 37 concentration to an effective DCGLw for this radionuclide.
4.10 The sample database used to determine the effective radionuclide mix for the OL10 area has been drawn from samples that were assayed at off-site laboratories. This list is shown on Attachment 2-2. The data shows Cs-1 37 to be the predominant radioactive contaminant found in these areas.
The decayed set of sample results were input to the spreadsheet titled "Effective DCGL Calculator for Cs-137' (Reference 3.9) to determine the effective volumetric DCGLw values. The output of this spreadsheet is shown on Attachment 2-3.
4.11   The Nal scan MDC calculation is determined based on a 25 cm/sec scan rate, a 1.38 index of sensitivity (95% correct detection probability and 60% false positive) and a detector sensitivity of 206 cpm/uRlh for Cs-137. Additionally, the detection system incorporates a Cs-1 37 window that lowers sensitivity to background in the survey unit.

SNEC CALCULATION SHEET Calculation Number                                      Revision Number                 Page Number E900-05-027                                                            0                     Page 7 of 9 Subject 0L6 and OL10 Open Land Area - Survey Design 4.12 The survey units described in this survey design were inspected by site personnel. A copy of portions of the SNEC facility post-remediation inspection report (Reference 3.10), is included as Attachment 9-1 to 9- *? .
4.13 No special area characteristics including any additional residual radioactivity (not previously noted during characterization) have been identified in this survey area.
4.14 The decision error for this survey design is 0.05 for the a value and 0.1 for the f3 value.
4.15 'Special measurements' (as described in the SNEC LTP) are not included in this survey design.
4.16 No additional sampling will be performed IAW this survey design beyond that described herein.
4.17 SNEC site radionuclides and their individual DCGLw values are listed on Exhibit I of this calculation.
4.18 The survey design checklist is listed in Exhibit 2.
4.19 Area factors are shown as part of Compass output (see Attachment 6-1).
5.0 CALCULATIONS 5.1     All calculations are performed internal to applicable computer codes or within an Excel spreadsheet.
6.0 APPENDICES 6.1     Attachment 1-1, is a diagram of survey areas 0L6 and OL10 areas (northern sector of SNEC site).
6.2     Attachment 2-1 to 2-3 is the sample results from the 0L6 site area. In addition, the DCGL calculation sheet has been included.
6.3     Attachment 3-1, is a copy of calibration data from typical Nal radiation detection instrumentation that may be used in this survey area (IAW Section 2.1.2).
6.4     Attachment 4-1 through 4-3, is the MDCscan calculation and supporting MicroShield output for volumetric materials.
6.5     Attachment 5-1, is the scan locations for the OL1 0 survey units.
6.6     Attachment 6-1 through 6-11, are Compass output for the 0L6, and the OL10 areas showing the number of required sampling points for these survey units.
6.7     Attachment 7-1 to 7-6, are the sample point locations with key coordinates for each survey unit own shon Attachment 7-6.
6.8     Attachment 8-1, is the soil variability results for selected soil samples from the 0L6 and OL10 areas.
6.9     Attachment 9-1 to 9- &         , is a copy of selected portions of the inspection reports for these survey units.

AFtr~             K                            SNEC CALCULATION SHEET Calculation Number                                                      Revision Number                          Page Number E900-05-027                                                                             0                               Page 8 of 9 Subject 0L6 and OLI0 Open Land Area -Survey Design Exhibit I SNEC Facility Individual Radionuclide DCGL Values                            (a) 25 mremly Limit                    4 mremly Goal 25 mremly Limit                   (All Pathways)                  (Drinking Water)
Radionuclide                   Surface Area                 Open Land Areas                  Open Land Areas (b)
(dpm/100cm2)               (Surface & Subsurface)           (Surface & Subsurface)
(pci/g)                           (pCi!9)
Am-241                         2.7E+01                           9.9                               2.3 C-14                         3.7E+06                             2                                5.4 Co-60                         7.1 E+03                           3.5                               67 Cs-1 37                       2.8E+04                            6.6                              397 Eu-152                        1.3E+04                           10.1                             1440 H-3                         1.2E+08                           132                               31.1 Ni-63                        1.8E+06                           747                            1.9E+04 Pu-238                        3.OE+01                            1.8                              0.41 Pu-239                        2.8E+01                            1.6                              0.37 Pu-241                        8.8E+02                            86                               19.8 Sr-90                         8.7E+03                            1.2                              0.61 NOTES:
(a) While drinking water DCGLs will be used by SNEC to meet the drinking water 4 mremly goal, only the DCGL values that constitute the 25 mrem/y regulatory limit will be controlled under this LTP and the NRC's approving license amendment (b) Listed values are from the subsurface model.      These values are the most conservative values between the two models (i.e..
surface & subsurface).

ai m                            SNEC CALCULATION SHEET Calculation Number                                                          Revision Number                         Page Number E900-05-027                                                              l                     0                l           Page9of 9 Subject OL6 and OLI0 Open Land Area -Survey Design Exhibit 2 Survey Design Checklist Calculation No.                                              lLoration Codes E900-05-027                           IOL6 & OLI 0 Open Land Areas Status       Reviewer REVIEW FOCUS                                           (Circle One)    Initials & Date Has a survey design calculation number been assigned and is a survey design summary description provided?
2            Are drawings/diagrams adequate for the subject area (drawings should have compass                 Ye    N            4*5 headings)?                                                   NA46 3          Are boundaries properly identified and is the survey area classification clearly indicated?              N/A             IYe 4                Has the survey area(s) been properly divided into survey units LAW EXHIBIT 10                Ye    N/A           '1-5                    Are physical characteristics of the areaflocation or system documented?             (          Nj/A&#xa3; 6                               Is a remediation effectiveness discussion included?
7             Have characterization survey and/or sampling results been converted to units that are            e    N/A comparable to applicable DCGL values?
8       Is survey and/or sampling data that was used for determining survey unit variance included?                N/ A          q4105 9          Is a description of the background reference areas (or materials) and their survey and/or                             412JI.,
sampling results included along with a justification for their selection?          Y          e s ,
10        Are applicable survey and/or sampling data that was used to determine variability included?                             "/N/A 11           Will the condition of the survey area have an impact on the survey design, and has the          Yes, probable impact been considered in the design?               Y       s       _G_   _
Has any special area characteristic incduding any additional residual radioactivity (not 12          previously noted during characterization) been identified along with its impact on survey        Yest 13          Are all necessary supporting calculations and/or site procedures referenced or included?       (Yes,"21/
14                        Has an effective DCGLw been identified for the survey unit(s)?                   CYs      N/A 15                   Was the appropriate DCGLEUc included in the survey design calculation?
16                 Has the statistical tests that will be used to evaluate the data been identified?       ()       N/A 17                 Has an elevated measurement comparison been performed (Class 1 Area)?                     Yes,.1                   4N,/js, 18         Has the decision error levels been identified and are the necessary justifications provided?   (i)       N/A              L/of 19         Has scan instrumentation been identified along with the assigned scanning methodology?          (S)      N/A 20           Has the scan rate been identified, and is the MDCscan adequate for the survey design?        CD N/A                   Lit  I 21       Are special measurements e.g., in-situ gamma-ray spectroscopy required under this design,                  N/A and is the survey methodology, and evaluation methods described?             X        .2~'
22        Is survey instrumentation calibration data included and are detection sensitivities adequate?          s N/A               L5 23      Have the assigned sample and/or measurement locations been clearly identified on a diagram                            l    Al or CAD drawing of the survey area(s) along with their coordinates?                 V   esj NM             I&II 24         Are investigation levels and administrative limits adequate, and are any associated actions clearly indicated?                                        Ye     N/A 25                    For sample analysis, have the required MDA values been determined.?                    Yes,    N/A 26      Has any special sampling methodology been identified other than provided in Reference 6.3?           Yes     N5 NOTE: a copy of this completed form or equivalent, shall be included within the survey design calculation.

132 131 130 29   128  127 INe    126 2  03  -0  10I   -0    1, II0 -~  -1 11"   t  I  ll"   "II      "I II 106 l. 107 106 106 Id 03 10 101 106 06 9 ST F      , F- 1-=--I- --              --
SRi:            MA4            MA3                            OL6 & OL 10 OPEN LAND SURVEY UNITS BQ 80
_  -              i    ,     ~~~RAYSTOWN JUNIATARIVER BRANCH                                                                                                             _
00                        0 O
:     l2 T     E 0
BO OL8
                                                        #73                                                                                                 DUMPSITE  /
   'OLS 0T0           0 0
a 00_.iZLt1 0     1     #78.      0/     0     ?I,,I ATTACHENT C0 0)

DCGL Calculation Logic - SNEC Facility Open Land Area OL6 & OL10 Survey Units: SNEC Site survey unit named OL6 and OL10
: 11.     

== Description:==
The purpose of this calculation is to determine a representative isotopic mix from available sample analyses for the OL6 and the OL10 survey areas of the SNEC Facility site. The effective volumetric DCGLWs are then determined from the mean percent of applicable samples.
Ill. Data Selection Logic Tables: The radionuclide selection logic and subsequent DCGL calculations are provided in five (5) tables. These tables were developed using Microsoft Excel. Table explanation is as follows.
Table 1: Raw Data Listing - This table provides a list of four (4) representative sample analysis results. Results are from scoping, and characterization survey activities of the OL4, OL5 & OL6 site areas (adjacent to OL1 0). The samples consist of soil samples that were taken in support of the aforementioned activities. As applicable, a sample number, sample location/description, radionuclide concentrabon, and analysis date are provided for each sample. Positive nuclide concentrations are noted with yellow shaded background fields while MDA values are noted in the gray shaded fields.
Table 2: Reduced Data Listing of Positive Results, MDAs Removed - This table provides the best overall representation of the raw data from table 1. Non-positive nuclide columns have been removed as well as all the MDA values leaving four (4) sample results. Thus, eleven (11) nuclides have been reduced to five (5) in this table.
Table 3: Decayed Sample List of Positive Results - This table decays the data from Table 2. Half-life values (in days) are listed above each respective nuclide column. Samples are decayed from their respective analysis date to March 15, 2005. Only positive results were decayed.
Table 4: Ratio to Cs-1 37 for Positive Sample Data - This table provides the calculation methodology for determining the surrogate ratio to Cs-1 37 for each radionuclide. From this information the mean, and mean % of total are calculated. The mean % of total values (normalized to 100%) are then used to calculate the effective volumetric DCGLW per MARSSIM equation 1-14.
See Table 5. Note that the mean percent values were averaged using only the positive sample results in each column. In some cases only a single nuclide value (e.g. Pu-238) had a positive result. This value is listed as the mean value in the tabulation. Therefore, this treatment results in a higher mean percent of total' value for the mix, which is considered a conservative approach.
Table 5: Effective DCGL Calculator for Cs-137 (in pCig) - This table provides the surrogate volumetric modified Cs-137 DCGLW calculation results from data derived from Table 4.
IV. Summary - The OL6 and OL10 site areas (OL4 & OL5 are adjacent to these areas), are largely soils and or rock material thus the release limit is based on a volumetric DCGLW. Additionally, these areas are in close proximity of each other. Using the above data selection logic tables the calculated Cs-1 37 surrogate volumetric DCGLW is 6.54 pCi/g. This value is reduced by 25% as part of the SNEC facilities commitment to apply an administrative limit as discussed in the License Termination Plan (LTP). Thus this methodology is considered a conservative approach.
ATTACHMEV1EN       C

TARI F I  RAW DATA I S-TING I SNEC Sample No              LAB No.               LocationlDescription      H-3     Sr-90     Co4        CS-137     Am-241          Pu-238            Pu.239     Pu-241   C-14 Ni43 Eu.152   AnalysIs Da"e SXSL5345    Teledyne, L23623-1 & L23663-.1RI BN-106, AP-1 @1Z'. OL6     0.519   0.0181     0.126       378         .Q95          0,0218            0.0026      1.48 0.1     2.7 0.769 May 27, 2004 SXSL4722           Teledyne; L23550-4         GRID BN-114, AP2, OL6     0.491 I 0.0394     0.068   I   64.6   l 0.0144                             0.028       2.92 i 0.14916.1         April 15, 2004 SXSL4873           Teslsne; L23650-2          GRID BF-118, AP1, 0L4     0.606   0.0341     2.15        213    1 0.0423           0.0423            0.0695      1.62 0.184 27.4 .657 April 28, 2004 SXSL4665           Teledyne; L23305-1        GRID BP-93 S.Soll - OL5    0,642    0.285     0.216       714 l     0. 09           0.0157             0157
                                                                                                                                                         .1              01711        0.      April 7, 2004 KEY Yellow Shaded Background - Positive Result IGray  Shaded Background - MDA TABLE 2, REDUCED DATA LISTING OF POSITIVE RESULTS, MDAs REMOVED SNEC Sample No                           LAB No.                          Locatlon/Descriptlon           Sr-90           Co-60           Cs-137           Pu-238        Pu-239       Analysis Date SXSL4665                     Teledyne; L23305-1                     GRID BP-93 S.Soil - 0L5         0.285            0.216             714                                                   004 SXSL4722                     Teledyne; L23550-4                      GRID BN-1 14, AP2, 0L6        0.0394                             64.6                      II              A      15, 2004 SXSL4873                     Teledyne; L23550-2                      GRID BF-118, AP1, 0L4         0.0341             2.15             213            0.0423        0.0695      April 28, 2004 SXSL5345           Teledyne, L23663-1 & L23663-I RI                 BN-106, AP-1 @ 12", 0L6        0.0181            0.126             378                                      May 27, 2004 TABLE 3, DECAYED SAMPLE LIST OF POSITIVE RESULTS T 112 (d)     T 112 (d)       T 1/2 (d)      T 1/2 (d)     T 112 (d)                         Decay Date 10446.2      1925.23         11019.59       32050.7 8813848                                   3/15/2005 SNEC Sample No                       LAB No.                      Location/Descriptlon         Sr-90        Co60            Cs-I 37       Pu-238         Pu-239         Elapsed (d)       Analysis Date SXSL4665                  Teledyne; L23306-1                GRID BP-93 S.Soil - 0L5       0.279         0.191         698.807                                           342          April 7, 2004 SXSL4722      I           Teledyne; L23550-4                 GRID BN-1 14, AP2, 0L6       0.039                     I  63.257      I            Il                      334        lApril  15, 2004 SXSL4873                  Teledyne; L23560-2                 GRID BF-118, AP1, 0L4        0.033         1.915         208.743          0.042          0.069             321         April28, 2004 SXSL5345         Tel      ne, L23663-1 &L23663-1RI          BN-106,AP-1 @12", 0L6         0.018         0.113         371.122                                           292          Ma    27, 2004 2
ATHACMEN'

TABLE 4, RATIO TO Cs-137 FOR POSITIVE SAMPLE DATA SNEC Sample No                             LAB No.                    Location/Description            Sr-90          Co-60        Cs-137        Pu-238         Pu-239          Analysis Date SXSL5345             Teledyne, L23663-1 & L23663-IRI           BN-106, AP-1 @ 12", 0L6         0.00040        0.00027       1.00000     _              __      _        May 27, 2004 SXSL4722                      Teledyne; L235504                GRID BN-114, AP2, 0L6           0.00061                      1.00000                                     April 15, 2004 SXSL4873                      Teledyne; L23550-2                GRID BF-118, AP1, 0L4          0.00016 0.00918              1.00000       0.00020 0.00033               April 28, 2004 SXSL4665                      Teledyne; L23305-1               GRID BP-93 S.Soil - 0L5         0.00005 0.00031              1.00000                                      April 7, 2004 Mean=>         0.00030 0.0033                1.0000       0.0002         0.0003 STDEV=>           0.00025         0.0051           0                          .                  Total Normalized to 100%=>                0.03%          0.32%        99.59%         0.02%          0.03%                 100.00%
Table 5 75%
Effective DCGL Calculator for Cs-1 37 (in pCilg)                                                                       !        6.56        Ip'ig 1       4.92    jpCi/g SAMPLE 1lUMBER(sJ* 0L6    Op en Land At e.
15.30%                25.0 mu em.' TEDE Limit                                                                                6.54         pCig         4.90      pCl!g 0.45%             _        mi enty Deinkit Wate. IDWI Limit Sample Inputthl UI_
(i)Cg, tCil,                 25 mfemly TEDE                   A - Allowed pClito                         Value Checked ftom          This Sample Isotope             etco.        'of  Total   Limits fpCigl                      25 menemly TEDE                            Column A oe B            nmuemtyTEDE 1 Ami-241                                  &deg;0.000% 9 9         -                         &deg; &deg;ltA241 z C-14                                 0.000%        2.0                                 0.00           11000                      0.00                                                 C-14 3 Co-60              0.0033            0.324%        3.5                                 0.02                                      0.02                      0.02                       Co40 4 Cs-137             1.0000           99.593%        6.6                                 6.54                                                                3.79                       Cs-137 s Ei-.152                              0.000%        10.1          _&deg;&deg;                                                             0.00                      0.00     _uu-1               52 6 H-3                                   0.000%        132                                 0.00                                      0.00                      0.00                       H-3 7 Ni-63                                 0.000%        747                     l           000                          _000                     l000                  li43 a Pu-2338            0.0002             0.020%        1.8 9 Pu-239             0.0003             0.033%        1.6                                 OM                                        0.00                      0.01                           29 i* Pti-241                               0.000%         86                                   .0.000                                                                                       P24 1'l Si-90             0.0003             0.030%        1.2               ..                0.00          .0.00                                                 00                          I9 i1.OOE+00          100.000%                                            6.56                  225.32              6.56                    3*25             0.018 Maximum Poo missfle            Maximum                                      To Use This hioi mlion     l pCilg          Pe. missile pClg                                Sample hptd Ur*s Must Be in 425 littem.:             44 muenvy)                              Icln 3
ATTACHMENT                a     f3_                                                                                                                                             C 0o

2350 INSTRUMENT AND PROBE EFFICIENCY CHART 02/22105 Added 2350-1 #126218 with 43-68 #095080 and 2350-1
      #126188 with 43-68 #099186. Returned from DURATEK following calibration. Typical - 2" by 2" Nal (w) Inst Response InsL#      Cal Due      AP#                    Probe     - Cal Due    cpn/mRfh 95361      6/25/05     P&W                    25686 Pk      6/28/05     211,799 98620      12/01/05    G&W                    196022 Pk     12/01/05    204,609 I__      __
98642      9/28/05     B&W                    185844 Pk      9/28/05    209,771 98647      11/02/05    G &Y                   211667 Pk     11/02/05    213,180 117566    01/05/06      ROR                     402PK       01/13/06    205411 117573      5/18/05    O& Y      _            211674 Pk      5/18/05    212,173 129407     12/17/05    White     _             206280       12/17/05    222,724 129423      5/18/05     P &Y                  211687 Pk      5/18/05    213,539 129440     11/01/05    O&W                    210938 Pk 11/01/05        196,636 126198     11/22/05     R&W l_              l_ 196021       11/22/05j   210398 I Diff-rm MW-MT-ob  U. D.I Caiu  o1y inVc   (lOmY o 100)
ATTACW-I1ENT             *-t*3

MicroShield v5.05 (5.05-00121)
GPU Nuclear Page     :1                                                                                 File Ref:
DOS File: SOIL.MS5                                                                              Date:
Run Date: IMarch 29, 2005                                                                         By:
Run Time: 33:38:06 PM                                                                     Checked:
Duration : ('0:00:03 Case

==Title:==
Soil

== Description:==
Soil Density 1.45 glcc, 6" Deep Cylinder @ 4" from Surface Geometry: 8 - Cylinder Volume - End Shields Source Dimensions Height             15.24 cm              6.0 in Radius            28.21 cm              11.1 in Dose Points X                Y                 z
                                                           # 1       0 cm           27.94 cm             0cm 0.0 in             11.0 in          0.0 in Shields Shield Name       Dimension      Material Density Source         2325.091 in3    Concrete 1.45 Air Gap                            Air     0.00122 Source Input Grouping Method: Actual Photon Energies Nuclide         curies          becquerels          uCi/cm3          Bq/cm 3 Ba- 137m     5.2264e-008        1.9338e+003       1.3717e-006      5.0753e-002 Cs-137        5.5247e-008        2.0441e+003       1.4500e-006      5.3650e-002 Buildup The material reference is : Source Integration Parameters Radial                                             60 Circumferential                                    60 Y Direction (axial)                                60 Results Enermy           Activity       Fluence Rate        Fluence Rate        Exposure Rate         ExDosure Rate MeV         photons/sec       MeV/cm 2 /sec       MeV/cm 2 /sec           mR/hr                 mR/hr No Buildup         With Buildup         No BuilduD            With Buildup 0.0318        4.003e+01          6.785e-06           8.211 e-06           5.652e-08             6.840e-08 0.0322         7.386e+01          1.305e-05          1.589e-05            1.050e-07             1.278e-07 0.0364        2.688e+01          7.222e-06           9.428e-06            4.103e-08             5.357e-08 0.6616         1.740e+03         5.968e-02           1.023e-01            1.157e-04             1.983e-04 TOTALS:         1.881e+03         5.971 e-02           1.023e-01           1.159e-04             1.986e-04 ATrvtqnr z4M            J

Nal Scan MDC Calculation- CV Soil.mcd Nal Scan MDC Calculation b := 200        p :- 0.5       HS d := 56.42          SR:= 25    d := 1.38
                                                                                       -4 Conv := 206                    MS output         1-15710 HS d HS d = 2.257   ObservationInterval (seconds)
SR i     HS d ObservationInterval (seconds) 1      SR
('bo b-:=    6 60 b ; = 7.523        Counts MDCR i:= Id     . i-MDCR ; = 100.629         net counts per minute MDCR; surveyor :=
MDCR surveyor     = 142.311            net counts per minute MDCR surveyor MDERC Conv MDER = 0.691               gR/h MDER MDC scan 1 10 MS output           3 MDC scan = 5.971              pci/9 41612005                                                                                                  4 of 5 ATTACHWANT               --   -

Nal Scan MDC Calculation- CV Soil.mcd where:
b = backgroundin counts per minute b= backgroundcounts in obsenrazioninterval Conm = Nal manufacturersreportedresponse to energy ofcontaminant (cpm/uR/h) d = index of sensitivity (Table 6.5 MARSSJM), 1.38 = 95% ofcorrect detection's, 60%false positives HSd = hot spot diameter (in centimeters)
MDCsc,,, = Minimum DetectableConcentrationfor scanning (pCoig)
MDCR, = Minimum Detectable Count Rate (ncpm)
MDCRsunoor = MDCR correctedby human performancefactor (ncpm)
MDER = linimum Detectable Exposure Rate (uRlh)
MSO.fpt = MicroShield output exposure ratefor I pCilg ofcontaminant (mRPh)
O = oberrationInterval (seconds) p = humanperformancefactor SR = scan rate in centimetersper second NOTE This is an example of an MDCscan calculation that is valid for a specific set of site conditions, and assumptions. These variables include the computer model used, soil density, soil moisture content, surveyor efficiency, ground cover, soil background radionuclide content and other variables that influence calculated results. However, this scan MDC's has been deemed appropriate for initial survey planning purposes at this site location.
5 of 5 41612005 416t2005                                                                                                        5 of 5 ATTA CSaN  1NT--3-So~

132     113     130      129  *26        127      126      125       124   I23    I22  21  120 119  *18  117   116 775  714
* 3  112 it, 110 109 106 707  106 I0D I04 03 102 707 100 90 go   97 06 56   94 93  92 pi 90 89 6                 ----- --                --l--r
                                               --- I---l--- --- l---I--F--- -[
MA4                          MA3              OL6 & OL10 OPEN LAND SURVEY UNITS - SCAN AREAS IN BLUE
                                                                                  \RAYSTOWN    BRANCH M.-                                                                 JUNIATA RIVER                                                                                                             +#7j
                                                                                                                                                                                                               .O6-      ,vv 0                                   0                                                                                                                                                                             a OM06 O8              _                    OL             6                      OL0O70ABNEDHEASTV~$9                                                  L8                   #2 0L80 03,   - t.,,F\nt           .. ,*i 00               -1OLO                                                                                                                                           0--
_      #73   o                           1                            00                  0         2 o  oo  A ,    I1 M9-                                  _                                                -6                 0   0        +         0      0    0        CUREN_
                                                           .               h             *       *g          (          XRC~l                    lEpoNNNGATTACHMENT 5 - 1

Site Report Site Summary Site Name:             OLl0 Open Land Areas Planner(s):            BHB Contaminant Summary NOTE:    Surface soil DCGLw units are pCi/g.
Building surface DCGLw units are dpnml00 cm2.
Screening Contaminant                             Type           DCGLw        Value Used? Area  (m') Area Factor Cs-1 37                              Surface Soil       4.90             No         1         28.7 25         4.7 100         3.6 400          3 2,500        2.3 10,000         1 COMPASS v1.0.0                                             41812005                                Page 1 ATTACHMENT       (        2..

Surface Soil Survey Plan Survey Plan Summary Site:                         OL10 Open Land Areas Planner(s):                   BHB Survey Unit Name:             OL1 0-1 Comments:
Area (M2):                    6,800                             Classification:                   2 Selected Test:                Sign                              Estimated Sigma (pCi/g):          0.33 DCGL (pCi/g):                 4.90                              Sample Size (N):                  14 LBGR (pCi/g):                 4.4                               Estimated Conc. (pCi/g):          0.4 Alpha:                        0.050                             Estimated Power:                  1 Beta:                         0.100 Prospective Power Curve 0.9 ---
0.8 -
                  -    0.7 -I
: 0.6 ----
4    0-
                      *0.5     -~
                    -  0.4   .
4 0.3 -
60.2 E 0.1      -
0                      2             3           4             5     6 Soil Concentration (Cilg), nacluiling background
                           -        Power          -     DCGL               - -    Estimated Power
                           -        LBGR             a   1-beta COMPASS v1.0.0                                            418/2005                                      Page 1 ATTA.!-,SFMNT         &          2-CoT

Surface Soil Survey Plan Contaminant Summary DCGLw      Inferred                         Modified DCGLw         Scan MDC Contaminant    (PCi/g)    Contaminant               Ratio       (pC~Ug)             (pCiIg)
Cs-137          4.90      N/A                       NIA           NIA                 N/A Survey Unit Estimate                 Reference Area Estimate (Mean +/- 1-Sigma)                       (Mean I 1-Sigma)
Contaminant                   (pci9)___     _                        (pCig9)
Cs-1 37                     0.45 +/- 0.33                            0.28 t 0.39 COMPASS v0.0.0                              4tt2W05                                        Page 2 ATTACHMENT-k--               3

Surface Soil Survey Plan Survey Plan Summary Site:                       OLIO Open Land Areas Planner(s):                 BHB Survey Unit Name:           OL1 0-2 Comments:
Area (m2):                  6,860                               Classification:                   2 Selected Test:              Sign                                Estimated Sigma (pCi/g):          0.33 DCGL (pCi/g):               4.90                                Sample Size (N):                  14 LBGR (pCUg):                4.4                                 Estimated Conc. (pCi/g):          0.4 Alpha:                      0.050                               Estimated Power:                  1 Beta:                       0.100 Prospective Power Curve
                      -I
                   ! 0.9
_ 0.8
                  -    0.7 ci t 0.6
                    *' 0.5
_ 0.4
                  . 0.3
_0.2 E 0.1 0
0          1            2            3            4             5     6 Soil Concentainn pCi/g), incluling backgrnuml
                           -      Power            -     DCGL               --     Estimated Power
                             -    LBGR
* 1-beta COMPASS v1.0.0                                           418/2005                                       Page 1 YrrA-,t oi2    W        (9r .,     yi COG

Surface Soil Survey Plan Contaminant Summary DCGLw      Inferred                             Modified DCGLw        Scan MDC Contaminant    (pCIlg)    Contaminant                   Ratio      (pCI1g)             (pCi/g)
Cs-1 37         4.90      N/A                            N/A          NIA                N/A Survey Unit Estimate                    Reference Area Estimate (Mean I -Sigma)                           (Mean 1-Sigma)
Contaminant                   (pig)                                      (pCIg)__
Cs-137                      0.45 +/- 0.33                                0.28 +/- 0.39 COMPASS v1.0.0                               418/2005                                         Page 2 ATTAVrP'Ju? 'KtT      1    . S

Surface Soil Survey Plan Survey Plan Summary Site:                      OLI0 Open Land Areas Planner(s):                BHB Survey Unit Name:          OL1 0-3 Comments:
Area (M2):                 7,000                              Classification:                 2 Selected Test:             Sign                               Estimated Sigma (pCi/g):        0.33 DCGL (pCi/g):              4.90                               Sample Size (N):                14 LBGR (pCi/g):             4.4                                Estimated Conc. (pCi/g):        0.4 Alpha:                     0.050                              Estimated Power:                1 Beta:                      0.100 Prospective Power Curve
                      -I 5 0.9 N
CA 0.5
_ 0.7
                  'a i 0.6 0.3
                  - ;~0.5
                  ;r_0.4 U
4 0.3 L  0.2
                  ?E 0.1 0          1          2             3           4            5     6 Soil Ceoceniraen.n (pCilg, including backgxruni
                               - Power          -     DCGL                - -  Estimated Power
                          -      LBGR
* l-beta COMPASS v1.0.0                                         4J812005                                    Page 1 Co0

                 'REZ-5/    Surface Soil Survey Plan Contaminant Summary DCGLw      Inferred                            Modified DCGLw        Scan MDC Contaminant       (pCl/g)    Contaminant                Ratio        (pCilg)             (pClIg)
Cs-137              4.90     NIA                         NIA            NIA                NIA Survey Unit Estimate                   Reference Area Estimate (Mean +/- 1-Sigma)                         (Mean +/- 1-Sigma)
Contaminant                      (pC11g)                                   (pCIlg)
Cs-1 37                        0.45 +/- 0.33                               0.28 +/- 0.39 V1.D.0 LUMPAbS vi.0.0                                 41812005 COMPASS                                        4A812005                                          Page 2 ATTACHMENT           6    *    > .~:

Site Report Site Summary Site Name:              OL6 Open Land Area Planner(s):             BHB Contaminant Summary NOTE:    Surface soil DCGLw units are pCVg.
Building surface DCGLw units are dpm/100 cm2.
Screening Contaminant                              Type           DCGLw   _    _
Value Used? Area (m') Area Factor Cs-1 37                              Surface Soil        4.90               No                  28.7 25        4.7 100        3.6 400         3 2,500       2.3 10,000        1 41812005                                 Page 1 COMPASS u1.0.0 COMPASS    vi.0.0                                           4U8/2005                                 Page I ATT^^W;t=          6 . 8

Surface Soil Survey Plan Survey Plan Summary Site:                          OL6 Open Land Area Planner(s):                    BHB Survey Unit Name:              OL6 Comments:                      INCLUDES THREE LOCATIONS Area (m 2):                    1,775                                  Classification:                     1 Selected Test:                 Sign                                   Estimated Sigma (pCi/g):            1.7 DCGL (pCi/g):                  4.90                                   Sample Size (N):                    16 LBGR (pCi/g):                  2.6                                    Estimated Conc. (pCi/g):            2.6 Alpha:                         0.050                                  Estimated Power:                    1 Beta:                          0.100                                  EMC Sample Size (N):                16 Scanning Instrumentation:                          2" by 2" Nal (w)
Prospective Power Curve X                    _                                        _    _
sj  09    -_ _                           _   _      _____
0.8 c            _______
                   -0.7 0.6
* 0.5
                   -C           _n                                             ___._
4 0.4                                                       _      _
                    -   0.3     ___
60.2-_ _
D 0.1 2.5            3.0        3.5         4.0       4.5         5.0        5.5   6.0 Soil Concextrteix (aCi/g), icliiding backgrsmil
                           -           Power                   DCGL                  -    Estimated Power
                           -           LBGR                    Il-beta COMPASS v1.0.0                                                  4J812005                                        Page 1 ATTACNWENT             6    -

MYSurface Soil Survey Plan Contaminant Summary DCGLw      Inferred                         Modified DCGLw         Scan MDC Contaminant    (pCi/n)    Contaminant                Ratio      (pCIg)              (pCi/g)
Cs-1 37         4.90      N/A                         N/A         N/A                5.971 Survey Unit Estimate                 Reference Area Estimate (Mean t I-Sigma)                       (Mean +/- I-Sigma)
Contaminant                    (pCIlg)                                (pC11g)
Cs-I 37                       2.6 +/- 1.7                            0.28 +/- 0.39 COMPASS v1.0.0                              418/2005                                       Page 2 ATTAC09MENTL

If! XI U,
* x                                              :;   ::      f 101 xi ison (EMC)
Q_               No additional sample, e reqwed because the actual scan MDC iless than the requoed scan MDC.                            ing instrumentation used.Then enterascan MDCforeach ALCULATE buttontoviewthe integrated survey design scan MDCand DCGL unts are in pCig.
Scanning Instrumentation

== Description:==
12" by 2' Nal (w)
                                                                            -Enter Scan MDC Contaminant. -,.      Il    Scan MDC: l: -I Cs-1 37                         5.971 l CALcuJLATE:. I Statistical Design-.                                   Hot Spot Design N: l       16                       Actual Scan MDC:     5.971 BoundedArea(m5: l            110.9.                           AreaFactor l     NJA AreaFactor. l          3.58                . .BoundedArea(m):           NIA I                           DCGLw. l          4.90                          -.Post-EMC N: l    16 Scan MDC Required:               17.5 I .;
    -                                               rw Enable Training Card Help
. i     .. i  .
vi .0.0                                                  8AK           NEXI ATTACHMEiNT          6          /

132    131    130   120   128   127   126   12$  124   123    122   121  120    11   1   a 1t7   '18  115  114 113  112   I      11   109 108   107 106  06   104 103 IT7-A--OL                                                                                                               P LA                     SURVEY UNITS-----------
F             ',         1-~MA4 n         .
                                                  +
r- MA3
                                                               ~RAYSTOWN BRANCH OL6 & OL IO OPEN LAND SURVEY UNITS t
BR _         \          X BR B0  __-                                                           JUNIATA RIVER                                                                         o                                               +#74t\\_ 0   0 7\
BP _OOO-   2
         ,cTDIE4-30_OC08                                                                       -                                L6                                       l                       12'5 I3          /
                                                                                                                                                                                                       #NORTH'EAST Ba                                                                                     18L14C*1                                                  9                 11       12 a a1~   *   ~    7L
                              #73 r7 3H 811t  _
Bl
_L      IOL.IOO        7 A       -    1              l 6   O        7  O ^1        4     ~+1a            t      2
                                                                                                                                             \
7                                 , :j E tu                _      F2                                      121             XF1     l%      _      O                         _
2_        3                                     L8 BD                                   __             9     ai              *n4 i        *^W0         ;7     r/
3*                               0L4 BA BE     -                                                                                                                  a    a               TA2O ATTAC8MENi                   r7-           fI COcL

132  131 130 129 128 127 126  125  124  123  122  121     120  119 118 117   116 115  114 113  112    111 BT BS FI          i                         I         IV BR
                 ,        -MA4                                                0M & OL0O OPEN LAN OL6 RAYSTOWN BRANCH BO    __ -                        i  mJUNIATA               RIVER                            e             OW 4P-BP      -
BO     -
BN_
BM_
4        +15       +1 BL_
OL1O-2 BK_
BJ_
I   (10         11      #192
                                                                                                                ,t 19 m BI BH    -
BG_
BF BE _
ATTACHMENT               7 -Z

TTACHMENT -.3 104 103 102 101   100   99   98     97 96 95 94 93 92 91
,ND SURVEY UNITS ATTACKMENT    e    *__
CI Z

125      124       123    122  121 120 119 118 117   116 115           114          113           112     111  110 109 108 107 106    105 BT BS T     -e
_                                     _  _                   I   I       I BR OL6 OPEN LA fVD SURVEY UNIT RAYSTOWN BRANCH ow-A BQ                             JUNIATA RIVER                                                                   OW-4R-0                                           W4
        --   CONCRETE BP    -
BO _
BN_
Bm   _tOL6 11        1!     13        .
BL               8_1       9+     1/
                                                                                                             #54 BK _         '+        t't 6     $7                           #70                                            0
* I ABANDONED AIR SAMPLING BJ
_          2Q(9     3)+      4 STATION                 t 2        3                                                                                                                    #92 By                                                              l    l ....... :::::::::  lll: .........  : Al_
I r t%,

OL10-1 SURVEY UNIT                      OL-6 SURVEY UNIT KEY GRID COORDINATES (in Metersi        KEY GRID COORDINATES (in Meters)
Location      Grid No.       (X,. Y)    Location    Grid No.      (X, Y)
No.1           BE- 24       3        7  No. I        BI-125     3        4 No. 6          BI-130       0        4  No.2         BJ-125     9        3 No.4           BG-125       2        6  No. 3        BJ-124     9        3 No. 4        BJ-123     9        3 OL10-2 SURVEY UNIT               No. 5       BK-125      3        2 KEY GRID COORDINATES (in Meters)     No. 6       BK-124      4        2 Location      Grid No.       (X, Y)-    No.7        BK-123      4        2 No.1           BA-117       3        5  No.8         BL-125     9        1 No.2           BE-117       3        3  No. 9        BL-124     9        1 No. 3          BE-115       5        3  No.10        BL-123     9        1 No.4           BE-113       7        3  No.11        BL-125     3        9 No. 5          BG-112       8        2  No.12        BL-124     4        9 No.6           BI-117       3        1  No.13        BL-123     4        9 No.10          BK-116       4        1  No.14        BN-114     5        7 No. 15       BN-113     5        7 OL10-3 SURVEY UNIT               No.16        BN-112     5        7 KEY GRID COORDINATES in Meters)      No.17        BO-114    10        5 Location      Grid No.'      (X, Y)     No.18        BO-112     0        5 No. 1          BK-107       2        5  No.19       BM-106      1        8 No. 2          BK-105       3        5  No. 20       BN-106     6        7 No. 6          BM-108       1        3 No.15           BR-95       9        8 No.16           BR-92       0        8 No. 17          BP-91       1       10 No.18          BM-91         1       3 AA4 k,* fcWT,  -q    -    G

se-                               Ieassalr7 Sample     C-. nL10 G              PCLl Sa     Ng*
No. Gnts in OLo  C SXSL6699    BK-103, SPI   014   SXSL6725  BK-124, API 43 SXSi6700    BK-103, SP2   013   SXSL6726  BK-124 AP2  2.5 SXSL6701    BL-103, SPI   015   SXSL6727  BJ-124, API 42 SXSL6702    BL-103SP2     0.14  SXSL6728  BJ-124. AP2 28 SXSL6703   BM-103. SPI   0.18  SXSL6821  BJ15I API     2 SXSL6704    BM-103. SP2    O0. SXSL6822  OJ-125. AP2 29 SXSL67O5   BK-104, SPI   017   SXSL6823  8.-125, AP3   2 SXSL6706    BK-104, SP2   014   SXSL6024  BK-125. SPI  1.7 SXSL6707    BL-104, SPI   013   SXSL6825  BK-t25, SP2 14 SXSL6706    BL-104 ,SP2   013   SXSL6826  8L-125s SPI 2.9 SXSL6709    BM-104 SPI    0.12  SXSL6027  BL-125 SP2  29 SXSL67tO IM-104 SP2        0.1  SXSL6832  BK-125, SPI  17 SXSL6711     _L           013   SXSL6833  BL4124 AP1  28 SXSL6722    BJ-110, SPI    0.1 SXSL6834   BL-124, SP2 23 SXSL673     BJ-110,SP2    012   SXSL6840  BJ-123 SPI  0 65 SXSL671    BK-105 SPI    025   SXSL6841  BJ-123. SP2 05 SXSL6772   BK-05, SP2    0.14  SXSL6042  B5-123, SP2 0.46 SXSL6773   BL-105, SP1   009   SXSL6843  BK-123, SPI   2 SXSL6774    B-t105, SP2   0.14  SXSL6844  BK-123, SP2  1.9 SXSL677S   BK-16, SPI    0o18  SXSL6845  BL-123, SPt  01O SXS16T76    BK-16. SP2    0.08  SXSL6846  BL-123, SP2 08 SXSL6777   BL-106 SPI     0.1  SXSL7354   B-125, AP1  33 SXSL6778    8-106, SP2    0.18  SXSL7355   8B-125,API 4 8 SXSL6779   BK-107. SP1   0.17  SXSL7356  BU25, AP2    33 SXS16780   BK-107, SP2   048   SXSL7357   81-25, AP3  1.2 SXSL697S   BG-1 12, API  027   SXSL7358   8125, AP4  4 5 SXSL6976    8G-1 12 AP2   056   SXSL737O   8-125. API  47 SXSL7M)9   BF-112. SP1    08   SXSL7371   8125, AP2   18 SXSL70O1 BF-112, SP2     046   SXSL73372  B-2
                                             -    AP3  83 SXSL701    BE-112, SPI    06   SXSL7373   BU25, AP4    3 SXSL7012   BE-12
               -     SP2  066                     o.-  2-6 SXSL7013   BE-113 SPI    093                S7DEV-    1.7 SXSL7014   BE-113 SP2     06 SXSL7017   SE-1A sPi      06 SXSL7018   BE-114 .SP2    07 SXSL7023   8B-117 SPI     09 SXSL7024   8B-117 SP2    02o SXSL70-3   BC-117?SPI    056 SXSL7037   BC-1 t SP2    063 SXSL72tO   B8-117, API   0.13 SXSL7230   BCl12, LA2     03 SXSL7375   BB-17. SPI    0 88 SXSL6540     BK-119-1    025 SXSL6566     BK-114-1    0 28 SXSL6578 IBJ-114-1        03 SXSL6M1       s1- 14-1   028 SXSL6S54     BU-1s-1      03 SXSL6587     BJ-115-1    0 24 SXSL6607     B1-16-1     0.16 SXSL6610     BU-17-1     016 SXSL6613     BS-117-      06 SXSL6616     BH-118-1     05 SXSL6619     B5-116-1    0.12 SXSL6625     BK-117-1    025 SXSL6628     81-117-1     03 SXSL6666     BK-118-1    013 SXSL6669     BJ-119-1     04 SXSL66S8      S-1 19-1   055 SXSL6691     B1-119-i    0 16 SXSL68M8    8M-125 SPI     0.7 SXSL6M2S   BM-125. SP2    0.5 SXSL6835   BM-124 SPI     06 SXSL6836 BM-W24.SP2         I SXSL6837   BM-124, SP2    09 SXSL6919    BK-122, SPI    08 SXSL6920    BK-122, SP2      1 SXSL5921    BL-122, SPI    05 SXSL6M22    BL-122. SP2    05 SXSL6923    BL-121, SPI   066 SXSL6924    BL-121 SP2     06 SXSL6925    BM-121, SPI      1 SXSL6926    BM-121t SP2   095 SXSL6s6S   BM-123, SP2     07 SXSL5969    BM-t22 SPI     1.2 SXSL7262 I8J-126 SPI       08 SXSL7263    BJ-126, SP2    1.2 SXSL7264    BK-126, SPI      1 SXSL7265    BK-126, SP2   039 SXSL279     BE-123, SP1    06 SXSL72aO    BE-123. SP2    1.1 SXSL1'279   BF-123, SP1    12 SXSL7298    BF-123, SP2    0.2 UeW,-"   0.45 S7DEV.>   oM3 ArACHIAEN

Exhibit 1 Survey Unit Inspection Check Sheet ORIGINAL SECTION 1 - SURVEY UNIT INSPECTION DESCRIPTION Survey Unit #                    OL6                Survey Unit Location                           Northeast Quad. of Grid Map Date       115/05            Time         1145       Inspection Team Members                                    K. Lane SECTION 2 - SURVEY UNIT INSPECTION SCOPE Inspection Requirements (Check the appropriate Yes/No answer.)                                         Yes   No     N/A
: 1. Have sufficient surveys (i.e., post remediation, characterization, etc.) been obtained for the survey unit?          X
: 2. Do the surveys (from Question 1) demonstrate that the survey unit will most likely pass the FSS?                     X
: 3. Is the physical work (i.e.. remediation & housekeeping) in or around the survey unit complete?                            X
: 4. Have all tools, non-permanent equipment, and material not needed to perform the FSS been removed?                         X
: 5. Are the survey surfaces relatively free of loose debris (i.e., dirt, concrete dust, metal filings, etc.)?                 X
: 6. Are the survey surfaces relatively free of liquids (i.e.. water, moisture, oil, etc.)?                               X
: 7. Are the survey surfaces free of all paint, which has the potential to shield radiation?                              X
: 8. Have the Surface Measurement Test Areas (SMTA) been established? (Refer to Exhibit 2 for instructions.)                            X
: 9. Have the Surface Measurement Test Areas (SMTA) data been collected? (Refer to Exhibit 2 for instructions.)                         X
: 10. Are the survey surfaces easily accessible? (No scaffolding, high reach, etc. is needed to perform the FSS)           X
: 11. Is lighting adequate to perform the FSS?                                                                             X
: 12. Is the area industrially safe to perform the FSS? (Evaluate potential fall & trip hazards, confined spaces, etc.)          X
: 13. Have photographs been taken showing the overall condition of the area?                                              X
: 14. Have all unsatisfactory conditions been resolved?                                                                         X NOTE: If a 'No' answer is obtained above, the inspector should immediately correct the problem or initiate corrective actions through the responsible she department, as applicable. Document actions taken and/or justifications in the 'Comrnents' section below. Attach additional sheets as necessary.
Comments:
Response to Question 3,4,5 BI-125 contains sawhorse barrier. BN-112 has many rock piles from excavation.
Response to Question 12 BM-106 has roped off small hole approximately 3' x 3'.
Survey Unit Inspector (print/sign)            Kevin Lane /
11 ---
Survey Designer (print/sign) I .            b) H3R0SE' E 9?a         -o5-- 6z7

Exhibit I Survey Unit Inspection Check Sheet                          ORIGINAL SECTION 1 - SURVEY UNIT INSPECTION DESCRIPTION Survey Unit # l                 OL 0                Survey Unit Location                           Northeast Quad. of Grid Map Date          4/15/05       l Time I 1100             Inspection Team Members                                     K. Lane SECTION 2 - SURVEY UNIT INSPECTION SCOPE Inspection Requirements (Check the appropriate Yes/No answer.)                                         Yes   No     N/A
: 1. Have sufficient surveys (i.e., post remediation, characterization, etc.) been obtained for the survey unit?          X
: 2. Do the surveys (from Question 1) demonstrate that the survey unit will most likely pass the FSS?                     X 3    Is the physical wordg (i e . remediation & housekeeping) in or around the survey unit complete?                           X
: 4. Have all tools, non-permanent equipment, and material not needed to perform the FSS been removed?                         X
: 5. Are the survey surfaces relatively free of loose debris (i.e.. dirt, concrete dust, metal filings, etc.)?                 X
: 6. Are the survey surfaces relatively free of liquids (i.e., water, moisture, oil, etc.)?                               X
: 7. Are the survey surfaces free of all paint, which has the potential to shield radiation?                              X
: 8. Have the Surface Measurement Test Areas (SMTA) been established? (Refer to Exhibit 2 for instructions.)                           X
: 9. Have the Surface Measurement Test Areas (SMTA) data been collected? (Refer to Exhibit 2 for instructions.)                        X
: 10. Are the survey surfaces easily accessible? (No scaffolding, high reach, etc. is needed to perform the FSS)                X
: 11. Is lighting adequate to perform the FSS?                                                                             X
: 12. Is the area industrially safe to perform the FSS? (Evaluate potential fall & trip hazards, confined spaces, etc.)        X
: 13. Have photographs been taken showing the overall condition of the area?                                              X
: 14. Have all unsatisfactory conditions been resolved?                                                                          X NOTE: If a 'No' answer is obtained above, the inspector should immediately correct the problem or initiate corrective actions through the responsible site department, as applicable. Document actions taken and/or justifications in the 'Comments' section below. Attach additional sheets as necessary.
Comments:
Response to Question 3,4,5 Grass getting high on french drain mound. BN-126 contains fallen trees. BO-116 contains 40%
multifloral rose jagger bushes on steep bank. BM-115 contains concrete block approx. 30" x 30". BP-111 and BO-1 11 wash out to river trip hazard. BO-1 09 (2) concrete REMP well heads approx. 2' x 2'. BN-91 contains stumps and fallen trees. BK-110 to 105 contains silt, fence and straw bales. BI-112 abandoned air sampling station concrete pad.
Response to Question 10 Majority of grids along riverbank are steep and unsafe to survey.
Response to Question 12 Survey unit has many tripping hazards such as fallen tree limbs and rough terrain.
Survey Unit Inspector (print/sign)              Kevin Lane I/                                                          Date    4115105 Survey Designer (print/sign) I             ,.        Ijg         b        /           .,  k                           Date                 C-.
A/Ja-Is OD- 65 q- a?

SURVEY REQUEST CONTINUATION SHEET SR NUMBER             l        0216           l AREA/LOCATION                             OL6 SPECIFIC SAMPLING/SURVEY INSTRUCTIONS OR COMMENTS RESULTS 

==SUMMARY==
FOR SR-0216 SR-0216 was issued to obtain radiological survey and sampling data to ensure Final Site Survey activities are complete. The survey unit covered under this SR is 0L6 (grids are listed in the SR). The SR required the following radiological measurements.
* Surface scan measurements using a 2" x 2" Nal detector (set to identify Cs-137). Survey techniques will be lAW the SR.
* A total of 20 Site Surface Dose Model Samples (SSDM) were provided to be taken for analysis. SNEC Calculation Sheet using 'COMPASS' program required 16 samples to be taken.
* Site Surface Dose Model Samples (Auger Method). Obtain samples as directed in the SR. Using the auger, obtain a sample 1 meter in depth.
* QC Repeat Measurements: A minimum of 5% of all surface scan measurements and sampling were re-performed using identical methodology. SSDM sampling was performed by taking a second sample from the same drill hole.
* QC Repeat Analysis: A minimum of 1 sample per SR or 5%, whichever is greater, of all SSDM samples were analyzed using identical methodology.
* Additional sampling/surveys were performed at the request of the SR coordinator.
: 1. Summary of Results A. Surface Scan Measurements (2" x 2" Nal Detector)
A 100% surface scan was required of all accessible areas of certain grids, lAW the SR. A total of 100.99%
of this Class 1 area was surveyed, which is well within design basis. (See Exceptions and Discrepancies, #4)
Results: With the exception of one location in grid 61--125, no areas indicated activity above the action level of > 350 GCPM (gross counts per minute).
B. Surface Static Measurements A static measurement was obtained in B1-125 at alarm point (AP) 1.
Results: AP-1: 529 gcpm.
Page 1 of 3 5/31/2005

SURVEY REQUEST CONTINUATION SHEET SRNUMBER              l          0216          l AREA/LOCATIONl                         OL6 SPECIFIC SAMPLING/SURVEY INSTRUCTIONS OR COMMENTS C. Site Surface Dose Model Sampling Twenty (20) SSDM samples were obtained. Two (2) SSDM QC samples were taken. These samples were statistically spaced based on a random starting point due to the lack of noticeable elevated activity during final post remediation scan/static surveys.
Results: Twelve (12) SSDM samples taken for this SR did not contain Cs-137. MDA activity range is from 0.06 pCig to 0.18 pCilg (forthe surrogate isotope, Cs-137). Forthe eight (8) samples, not including QC samples that did contain Cs-137, activities were 0.22 pCi/g to 0.81 pCi/g. No other licensed isotopes identified for this particular SR.
: 2. Quality Control (QC) Measurements and Comparisons
* Repeat Scan measurements and SSDM samples were performed and met the applicable acceptance criteria established in Section 4.6 of E900-IMP-4520.04. QC scan measurements were repeated for 6.69% of the area scanned. SSDM sample QC measurements were repeated for 10.00% of SSDM samples.
: 3. Quality Control Sample Recounts
* Repeat QC replicate recount - SNEC has determined that, at a minimum, one SSDM sample, or five per cent (5%) of SSDM samples from each SR will have replicate gamma spectroscopy counts performed on them. In the case of this SR, 2 SSDM samples had replicate counts performed; samples
       #1-23954 and sample #1-23974, satisfying this requirement.
: 4. Exceptions and DiscrepanciestS
* The total area scanned of 100.99% value is due to a variance in estimated area taken from the Survey Design used in writing the SR, versus land area actually measured during survey of the area.
* When the actual land area surveyed value is used and the obstructions due to trees and the Juniata River is taken into account the actual percentage of land scan surveyed is 99.58% which equates to 100% of accessible areas.
Page 2 of 3 5/31t2005

SURVEY REQUEST CONTINUATION SHEET SR NUMBER             l         0216            l AREA/LOCATIONl                         OL6 SPECIFIC SAMPLING/SURVEY INSTRUCTIONS OR COMMENTS
: 5. Special Note(s)
* As stated previously, as this is a Class 1 area, scan coverage of approximately 100% will suffice to show due diligence in survey technique for release of the site for unrestricted use.
* QC Static measurement taken at AP-1 was 623 gcpm.
* One (1) SSDM sample was taken at the AP. Three (3) additional samples were taken to bound the AP to ensure no activity migration has occurred. All samples were taken in grid BI-125.
* Cs-1 37 activity found in soil at the AP was 1.53 pCig.
* One (1) bounding sample showed activity greater than MDA at 0.26 pCi/g.
* MDA for samples taken for AP resolution ranged from 0.05 to 0.12 pCilg.
* A replicate sample for sample #1-23887 was performed.
g yW        57.                                                                       6 Print/Signature                                                                                Date Page 3 of 3 5/3 1/2005

SURVEY REQUEST CONTINUATION SHEET SR NUMBER              l       0217          l AREA/LOCATION l                         OL10-1 SPECIFIC SAMPLING/SURVEY INSTRUCTIONS OR COMMENTS RESULTS 

==SUMMARY==
FOR SR-0217 SR-0217 was issued to obtain radiological survey and sampling data to ensure Final Site Survey activities are complete. The survey unit covered under this SR is OL10-1 (grids are listed in the SR). The SR required the following radiological measurements.
* Surface scan measurements using a 2 x 2" Nal detector (set to identify Cs-137). Survey techniques will be JAW the SR.
* A total of 18 Site Surface Dose Model sample (SSDM) points were provided to be taken for analysis.
SNEC Calculation Sheet using 'COMPASS" program required 14 samples to be taken.
* Site Surface Dose Model Samples (Auger Method). Obtain samples as directed in the SR. Using the auger, obtain a sample 1 meter in depth.
* QC Repeat Measurements: A minimum of 5% of all surface scan measurements and sampling were re-performed using identical methodology. SSDM sampling was performed by taking a second sample from the same drill hole.
* QC Repeat Analysis: A minimum of 1 sample per SR or 5%, whichever is greater, of all SSDM samples were analyzed using identical methodology.
* Additional sampling/surveys were performed at the request of the SR coordinator.
: 1. Summary of Results A. Surface Scan Measurements (2" x 2" Nal Detector)
A 100% surface scan was required of all accessible areas of certain grids, lAW the SR. A total of 55.45%
of this Class 2 area was surveyed, which is well within design basis.
Results: With the exception of one location in grid BH-125, no areas indicated activity above the action level of > 350 GCPM (gross counts per minute).
B. Surface Static Measurements A static measurement was obtained in BH-125 at alarm point (AP) 1.
Results: AP-1: 498 gcpm.
Page I of 3 5/31/2005

                  --      ISURVEY REQUEST CONTINUATION SHEET SR NUMBER                         0217           AREA/LOCATION I                      OL10-1 I                       SPECIFIC SAMPLING/SURVEY INSTRUCTIONS OR COMMENTS                                       I C. Site Surface Dose Model Sampling Eighteen (18) SSDM samples were obtained. Two (2) SSDM QC samples were taken. These samples were statistically spaced based on a random starting point due to the lack of noticeable elevated activity during final post remediation scan/static surveys.
Results: Nine (9) SSDM samples taken for this SR did not contain Cs-137. MDA activity range is from 0.06 pCi/g to 0.15 pCVg (for the surrogate isotope, Cs-137). For the nine (9)samples, not including C samples that did contain Cs-137, activities were 0.09 pCVg to 0.50 pCi/g. No other licensed isotopes identified for this particular SR.
: 2. Quality Control (QC) Measurements and Comparisons
* Repeat Scan measurements and SSDM samples were performed and met the applicable acceptance criteria established in Section 4.6 of E900-IMP-4520.04. QC scan measurements were repeated for 5.83% of the area scanned. SSDM sample QC measurements were repeated for 11.11% of SSDM samples.
: 3. Quality Control Sample Recounts
* Repeat CC replicate recount - SNEC has determined that, at a minimum, one SSDM sample, or five per cent (5%) of SSDM samples from each SR will have replicate gamma spectroscopy counts performed on them. In the case of this SR, 2 SSDM samples had replicate counts performed; samples,
        #1-23994 and sample #2-23996, satisfying this requirement.
: 4. Exceptions and Discrepancies
* The grids requiring 100%/ scan that were not scanned to this standard had obstacles such as power poles and trees located within the grid areas. This equates to 100% of the accessible grid area being surveyed.
* Grid BG-124 was changed to grid BG-125 on SR by the SR Coordinator.
* Sample Points (SP) 6 & 7 taken at a depth of 6' due to being north of the Penelec electric substation.
Page 2 of 3 611/2005 Page 3 of 3 sqnlnnnv

SURVEY REQUEST CONTINUATION SHEET SRNUMBER                        0217              AREAILOCATION                          OL10-1 SPECIFIC SAMPLING/SURVEY INSTRUCTIONS OR COMMENTS
: 5. Special Note(s)
* As stated previously, as this is a Class 2 area, scan coverage of approximately 30-50% will suffice to show due diligence in survey technique for release of the site for unrestricted use.
* QC Static measurement taken at AP-1 was 468 gcpm.
* One (1) SSDM sample was taken at the AP. Three (3) additional samples were taken to bound the AP to ensure no activity migration has occurred. All samples were taken in grid BH-1125.
* Cs-1 37 activity found in soil at the AP was 3.13 pCi/g.
* One (2) bounding samples showed activity greater than MDA at 0.10 pCi/g and 1.11 pCilg.
* MDA for samples taken for AP resolution ranged from 0.06 to 0.12 pCilg.
* A replicate sample for sample #1-23882 was performed.
Print/Signature                                                                                  Date Page 3 of 3 5/31/2005

SURVEY REQUEST CONTINUATION SHEET SR NUMBER                        0218           AREAILOCATION                          OL10-2 SPECIFIC SAMPLING/SURVEY INSTRUCTIONS OR COMMENTS RESULTS 

==SUMMARY==
FOR SR-0218 SR-0218 was issued to obtain radiological survey and sampling data to ensure Final Site Survey activities are complete. The survey unit covered under this SR is OL10-2 (grids are listed in the SR). The SR required the following radiological measurements.
* Surface scan measurements using a 2" x 2" Nal detector (set to identify Cs-1 37). Survey techniques will be IAW the SR.
* A total of 19 Site Surface Dose Model (SSDM) sample points were provided to be taken for analysis.
SNEC Calculation Sheet using OCOMPASS" program required 14 samples to be taken.
* Site Surface Dose Model Samples (Auger Method). Obtain samples as directed in the SR. Using the auger, obtain a sample 1 meter in depth.
* Site Surface Dose Model Samples (Track Hoe Method). In areas where the auger does not penetrate the ground, obtain samples in areas as directed by the SR.
* QC Repeat Measurements: A minimum of 5% of all surface scan measurements and sampling were re-performed using identical methodology. SSDM sampling was performed by taking a double size batch of soil and dividing it into 2 separate samples.
* QC Repeat Analysis: A minimum of 1 sample per SR of all SSDM samples were analyzed using identical methodology.
* Additional sampling/surveys were not performed.
: 1. Summary of Results A. Surface Scan Measurements (2" x 2" Nal Detector)
A 100% surface scan was required of all accessible areas of certain grids, IAW the SR. A total of 54.11%
of this Class 2 area was surveyed, which is well within design basis. (See section #4)
Results: No areas indicated activity above the action level of >350 GCPM (gross counts per minute).
B. Surface Static Measurements No static measurements were obtained.
Results: Not Applicable.
Page 1 of 3 6/16/2005

I SURVEY REQUEST CONTINUATION SHEET                                                   I SR NUMBER                        0218            AREA/LOCATIONl                        OLIO-2 SPECIFIC SAMPLINGISURVEY INSTRUCTIONS OR COMMENTS C. Site Surface Dose Model Sampling Twenty five (25) SSDM samples were obtained. Two (2) SSDM QC samples were taken. These samples were statistically spaced based on a random starting point due to the lack of noticeable elevated activity during final post remediation scan/static surveys. (See Section 5)
Results: Sixteen (16) SSDM samples taken for this SR were less than MDA. MDA activity range is from 0.05 pCi/g to 0.17 pCilg (forthe surrogate isotope, Cs-137). Forthe nine (9) samples, not including QC samples, that did contain Cs-1 37 greater than the sample MDA, activities ranged from 0.10 pCi/g to 0.37 pCilg. No other licensed isotopes identified for this particular SR.
: 2. Quality Control (QC) Measurements and Comparisons
* Repeat Scan measurements and SSDM samples were performed and met the applicable acceptance criteria established in Section 4.6 of E900-IMP-4520.04. QC scan measurements were repeated for 5.39% of the area scanned. SSDM sample QC measurements were repeated for 8.00% of SSDM samples.
: 3. Quality Control Sample Recounts
* Repeat QC replicate recount - SNEC has determined that, at a minimum, one SSDM sample from each SR will have replicate gamma spectroscopy counts performed on them. In the case of this SR, 2 SSDM samples had a replicate count performed; sample #2-24034 and #2-24114, satisfying this requirement. In addition, monthly, approximately five per cent (5%) of all samples counted on the gamma spectroscopy system or Tri-Carb system, lAW SNEC Procedure E900-QAP-4220.02, are required to be counted for replicate analysis. (e.g. FSS soil samples) E900-4MP-4520.04 requires 5%
replicate recounts.
: 4. Exceptions and Discrepancies
* A total of 3,800 m2 was designed for complete scanning. Due to trees, gullies, rocks, poles and steep slopes 3,711.94 m2 was actually scanned. See individual surveys for more detailed information.
* SSDM sample points (SP) 12B, SP-16B, and SP18B, depths were 1 meter to 2 meters.
* SSDM SP-12C, SP-16C, and SP-18C depths were 2 meters to 3 meters.
Page 2 of 3 6116/2005

SURVEY REQUEST CONTINUATION SHEET SR NUMBER            l           0218            lAREA/LOCATION I                           OL10-2 SPECIFIC SAMPLING/SURVEY INSTRUCTIONS OR COMMENTS
: 5. Special Note(s)
* As stated previously, as this is a Class 2 area, scan coverage of approximately 10%-50% will suffice to show due diligence in survey technique for release of the site for unrestricted use.
* SSDM samples SP-10, SP-12, SP-16 and SP-18 were taken with a track-hoe
* The Track-Hoe was needed for the above sample points due to overlying debris that prevented access to the site base soil. As all calculations for the release of the site for unrestricted use are based on the amounts of radioactivity present in the base soil, the debris needed to be removed for correct sampling methodology.
C/419 I 1W4/X1/,15 Print/Signature
                                            /5%!                                                       Date Page 3 of 3 6f16/2005

SURVEY REQUEST CONTINUATION SHEET SR NUMBER           l         0219          l AREAILOCATION I                       OLIO-3 SPECIFIC SAMPLING/SURVEY INSTRUCTIONS OR COMMENTS RESULTS 

==SUMMARY==
FOR SR-0219 SR-0219 was issued to obtain radiological survey and sampling data to ensure Final Site Survey activities are complete. The survey unit covered under this SR is OL10-3 (grids are listed in the SR). The SR required the following radiological measurements.
* Surface scan measurements using a 2" x 2" Nal detector (set to identify Cs-137). Survey techniques will be 1AW the SR.
* A total of 18 Site Surface Dose Model (SSDM) sample points were provided for samples to be taken for analysis. SNEC Calculation Sheet using "COMPASS" program required 14 samples to be taken.
* Site Surface Dose Model Samples (Auger Method). Obtain samples as directed in the SR. Using the auger, obtain a sample 1 meter in depth.
* QC Repeat Measurements: A minimum of 5% of all surface scan measurements and sampling were re-performed using identical methodology. SSDM sampling was performed by taking a second sample from the same drill hole.
* QC Repeat Analysis: A minimum of I sample per SR or 5%, whichever is greater, of all SSDM samples were analyzed using identical methodology.
* Additional sampling/surveys were not performed.
: 1. Summary of Results A. Surface Scan Measurements (2" x 2" Nal Detector)
A 100% surface scan was required of all accessible areas of certain grids, lAW the SR. A total of 45.41%
of this Class 2 area was surveyed, which is well within design basis.
Results: No areas indicated activity above the action level of >350 GCPM (gross counts per minute).
B. Surface Static Measurements No static measurements were obtained.
Results: Not Applicable.
Page l of 3 6116/2005

SURVEY REQUEST CONTINUATION SHEET SR NUMBER            -           0219           l AREAILOCATION l                      OL1O-3 SPECIFIC SAMPLING/SURVEY INSTRUCTIONS OR COMMENTS C. Site Surface Dose Model Sampling Fifteen (15) SSDM samples were obtained. Two (2) SSDM QC samples were taken. These samples were statistically spaced based on a random starting point due to the lack of noticeable elevated activity during final post remediation scan/static surveys.
Results: Fourteen (14) SSDM samples taken for this SR were less than MDA. MDA activity range is from 0.04 pCig to 0.17 pCilg (for the surrogate isotope, Cs-137). For the one (1)sample, not including QC samples, that did contain Cs-1 37 activity greater than the sample MDA, activity was 0.15 pCilg. No other licensed isotopes identified for this particular SR.
: 2. Quality Control (QC) Measurements and Comparisons
* Repeat Scan measurements and SSDM samples were performed and met the applicable acceptance criteria established in Section 4.6 of E900-IMP-4520.04. QC scan measurements were repeated for 6.29% of the area scanned. SSDM sample QC measurements were repeated for 13.33% of SSDM samples.
: 3. Quality Control Sample Recounts
* Repeat QC replicate recount - SNEC has determined that, at a minimum, one SSDM sample, or five per cent (5%) of SSDM samples from each SR will have replicate gamma spectroscopy counts performed on them. In the case of this SR, 1 SSDM sample had a replicate count performed; sample
       #5-24014, satisfying this requirement.
: 4. Exceptions and Discrepancies            I*
* Trees and the bank of the Raystown Branch of the Juniata River precluded 100% survey of the grids listed in the SR. See individual surveys for area not surveyed in each grid.
* Six (6)grids were deleted by the SR Coordinator due to being underwater/river bank too steep; with the Design Engineer's concurrence.
* Survey Design package calls for a minimum of 35 grids to be scanned in the area covered by this SR.
By deleting 6 grids a total of 34 grids were scanned. (see Section 5 for details)
* SP-14, SP-15, SP-16 were deleted by the design engineer due to either being in the river or being on too steep a slope for safe sampling.
* SP-3 depth of penetration halted at 0.5 meters due to rock formations.
Page 2 of 3 6/16!2005

SURVEY REQUEST CONTINUATION SHEET SR NUMBER            l         0219           l AREA/LOCATIONl                           OL10-3 SPECIFIC SAMPLING/SURVEY INSTRUCTIONS OR COMMENTS
: 5. Special Note(s)
* As stated previously, as this is a Class 2 area, scan coverage of approximately 10%-50% will suffice to show due diligence in survey technique for release of the site for unrestricted use.
* Per discussion with the unit Design Engineer at approximately 1030 EDT on 612/05, the number of grids designed by the program was intended to provide 50% coverage of the area. As the areas surveyed provided sufficient scanned area for this Class 2 area release no further action is required for documentation purposes.
A, /41[V,                   I-Print/Signature                                                                                   Date Page 3 of 3 6116/2005}}