View source for Backflow preventer

A '''backflow prevention device''' is used to protect [[potable water]] supplies from contamination or pollution due to [[backflow (plumbing)|backflow]].

In [[water supply]] systems, water is normally maintained at a significant pressure to enable water to flow from the tap, shower etc. When pressure fails or is reduced, as may happen if a water main bursts, pipes freeze or there is unexpectedly high demand on the water system, then such reduced pressure in the pipe may allow contaminated water from the ground, from storage or from other sources to be drawn up into the system.

==List at JAF==
{{#ask:[[Category:SSC]][[Category:Backflow preventer]]|?Description|format=ol}}

==Terminology==
Points at which a potable water system connects with a non-potable water system, are called '''cross connections'''.

'''Backflow''' means the undesirable reversal of flow of a liquid, gas or solid into the potable water supply &mdash; A '''backflow preventer''' keeps this from happening.

'''Back-siphonage''' occurs when higher pressure fluids, gases, or suspended solids move to an area of lower pressure fluids. For example, using a straw to drink a beverage; the suction of drink will make the pressure of fluid inside the straw lower, thus, liquid will move from the cup to inside the straw and then up to your mouth. This is an example of an '''indirect cross-connection''' &mdash; undesirable material is being '''pulled''' into the system.

If instead, air is blown through the straw and bubbles begin to erupt at the submerged end, this is an example of '''back-pressure'''. If instead of air, natural gas had been forced into a potable water tank, it in turn could be carried to your kitchen faucet. This is an example of a '''direct cross-connection''' &mdash; undesirable material is being '''pushed''' into the system.

Back pressure can force an undesirable contaminant to enter potable water piping. Sources of back pressure may be pumps in the water distribution system, boilers, heat exchanging equipment, or power washing equipment. In these cases there may be an almost constant risk of overcoming the static water pressure in the piping.  To reduce the risk of contamination, a backflow preventer can be fitted.  A backflow preventer is also important when potentially toxic chemicals are used, for instance for commercial/industrial descaling (boilers) or when bleaches are used for residential power washing.

==Preventive devices==
[[File:Verifiedbackflow.jpeg|thumb|backflow prevention device]]
The simplest, and a very effective way to provide backflow prevention, is to provide an [[air gap (plumbing)|air gap]]. An air gap is simply an open space between any device that connects to a plumbing system (like a valve or faucet) and any place where water can collect or pool.

Alternatively, a specialized backflow preventer valve may be installed at strategic locations in the plumbing system wherever there is a risk of contaminated fluids entering the water supply pipes.

==Regulatory requirements==
To prevent contamination due to back pressure, many health regulatory regimes require an air gap or mechanical backflow prevention assembly between the delivery point of mains water and local storage or use. Where submerged mains inflow is permitted, a backflow prevention assembly is required, which protects the potable water system from contamination hazards. A [[check valve]] is a basic form of backflow prevention, but often more complex devices are required as check valves are not considered as reliable when compared to devices with redundancies and reduced pressure zones.

In the US, the [[United States Environmental Protection Agency|Environmental Protection Agency]] (EPA) holds local water suppliers responsible for maintaining a certain amount of purity in potable water systems. Many states and/or local municipalities require annual testing of backflow prevention assemblies. In most cases, the law requires a double check (DC), Reduced Pressure Principle Device ([[Reduced pressure zone device|RP]]) device, or an air gap when backflow prevention is mandated.

===In New York===
Backflow preventers are installed for *some regulatory reference reason* and inspected annually. The reporting requirements in New York can be found in the installation/inspection form [[DOH-1013, Report on Test and Maintenance of Backflow Prevention Device]]. This form gets submitted to county and other interested parties within 30 days.

==Partial list of backflow prevention devices==
*[[Air gap (plumbing)|Air gap]]
*[[Atmospheric vacuum breaker]] (AVB)
*[[Check valve]] (usually not a legally approved method of backflow prevention)
*[[Chemigation valve]] (primarily used in agriculture)
*[[Double check valve]], or double check valve assembly (DCVA)
*[[Pressure vacuum breaker assembly]] (PVB)
*[[Reduced pressure zone device]] (RPZ)
*[[Spill resistant pressure vacuum breaker assembly]] (SPVB)
*[[Vacuum breaker]]


==See also==
* [[wikipedia:Backflow prevention device]]

{{mechanical vocabulary}}