View source for 1CAN108206, Discusses Operability of Dresser Model 31739A Pressurizer Safety in Util & Vendor Documentation.Ring Settings Should Not Cause Valve Chatter & Mechanical Damage.Analytical Models Being Developed for plant-specific Data

{{Adams
| number = ML20069J645
| issue date = 10/19/1982
| title = Discusses Operability of Dresser Model 31739A Pressurizer Safety in Util & Vendor Documentation.Ring Settings Should Not Cause Valve Chatter & Mechanical Damage.Analytical Models Being Developed for plant-specific Data
| author name = Marshall J
| author affiliation = ARKANSAS POWER &amp; LIGHT CO.
| addressee name = Stolz J
| addressee affiliation = NRC OFFICE OF NUCLEAR REACTOR REGULATION (NRR)
| docket = 05000313
| license number = 
| contact person = 
| document report number = 1CAN108206, NUDOCS 8210250206
| document type = CORRESPONDENCE-LETTERS, INCOMING CORRESPONDENCE, UTILITY TO NRC
| page count = 2
}}

=Text=
{{#Wiki_filter:?
ARKANSAS POWER & LIGHT COMPANY POST OFFICE box 551 UTTLE ROCK. ARKANSAS 72203 (501)371-4000 October 19, 1982 1CAN108206 Director of Huclear Reactor Regulation ATTN:    Mr. J. F. Stolz, Chief Operating Reactors Branch #4 Division of Licensing U. S. Nuclear Regulatory Commission Washington, D. C. 20555

==Subject:==
Arkansas Nuclear One - Unit 1 Docket No. 50-313 License No. DPR-51 Operability of Pressurizer Safety Valves Gentlemen:
The purpose of this letter is to document AP&L's position relative to the operability of the pressurizer safety valves installed on ANO-1. This issue has recently received increased attention due to i determination by Duke Power Company on October 14, 1982, that the Dresser safety valves on Oconee 2 were inoperable. Oconee 2 was subsequently shut down to perform adjustments on these valves. This decision was based on data obtained from the EPRI Relief and Safety Valve test program. This test program was established to address NRC concerns relative to safety and relief valve performance documented in NUREG 0737.
As described via letter from Mr. J. H. Taylor of B&W to Dr. R. C. DeYoung of the NRC dated October 15, 1982, the data examined which led to this concern was for valve models 31739A and 31709NA, manufactured by Dresser Industry.
A recent review indicated that for certain adjustment ring settings and back pressure conditions, full design capacity may not be achieved. In addition, at extreme ring settings, valve chatter could occur.
The final results of the EPRI test program were submitted to the NRC via {{letter dated|date=April 1, 1982|text=letter dated April 1,1982}}, from Mr. David Hoffman of Consumers Power Company. These results were later referenced on the ANO-1 docket by {{letter dated|date=July 28, 1982|text=letter dated July 28, 1982}}, (1CAN078211). It should be noted that the safety valves installed on ANO-1 are Dresser model 31759A valves, which are intermediate in size compared to the model 31739A and 31709NA tested in the EPRI program. Therefore, optimum adjustment ring settings are not directly available from the EPRI test data, nor can degradation of valve capacity be quantitatively determined for given adjustment ring settings. As noted in our {{letter dated|date=July 28, 1982|text=July 28, 1982, letter}}, however, AP&L has been continuing in our efforts to evaluate the effects of ring settings on valve performance.            This involves a cooperative effort with other B&W owners to develop analytical 8210250206 821019 PDR ADOCK 050003'.3 P                 pyg MEMBER MtOOLE SOUTH UTILITIES GYSTEM

                                                                  . w                         -
J. F. Stolz                          2                               Octob r 19, 1982
                                                                                     .                                                 m models which could be used to extrapolate from the EPRI data ,to'obtain plant specific valve adjustments.                                 ?       -
In the interim AP&L has determined, by a review of'AP&L and vendor                              '
N4 documentation, the current safety valve adjustment ringmsettings and has j                                                 f compared these settings to EPRI data for similar settings on the larger and-/                                               ,
s" smaller valves. Based on this review, we conclude the ANO-1 pressurizer
* N safety valves will perform satisfactorily.        Specifically, the adjustment rings are not in a range where valve chatter and resultant mechanical damage                                               ,/
would be expected. Although there may be some reduction in valve capacity, we do not feel that such reduction would prevent the valves from performing their intended function. As discussed in B&W's {{letter dated|date=October 15, 1982|text=October 15, 1982, letter}}, only a small percentage of the flow from one valve is needed for moderate frequency events. Calculations also indicate that even a postulated rod withdrawal from low power would require full capacity from only one valve (or fify percent capacity from each valve). This event is the basis for ANO-1 Technical Specification 3.1.1.3, which requires these valves to be operable. ANO-1 is currently operating with all rods out during an end of cycle coastdown. Based on our review of the EPRI data we do not feel that flow reductions below fifty percenticapacity.are probable with our current
                                     ~
valve adjustments.
The in'ormation discussed above was reviewed by the ANO-1 Plant Safety Committee (PSC) on Friday, October 15, 1982~ The PSC determined the safety valves to be operable as required by Technical Specification 3.1.1.3.
Therefore we c'o not plan to take further action at this time. We are,                                                           ,
however, continuing in our efforts to utilize the results of the EPRI test                                                       A data to determine optimum, plant specific, valve adjustments. As this work continues we will make adjustments to the safety valves as needed.
                                                                                                                            ~
ery truly yours, .
                                                            . //                                                            N. ,
John R. Marshall                                                             [
Manager, ligensing                         ,
JRM:DH:rd                                             s .,
0              ,
                                                                                                                      . n        ,
                                                                                         .g            4     Y,
                                                                                                  /
                                                                                           %.*'fx    /.
y 4
s       J 1
h
                                                        -       -   -..      , - -                       -          - --             ,}}